PWM-120 120W PWM Output LED Driver series 2 (for DA2-Type only) IS 15885(Part 2/Sec13) IP67 05 THOMAS SAMUEL THOMAS SAMUEL R-41027766 ( for PWM-120-12,24 only) except for 12DA type File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver series SPECIFICATION MODEL OUTPUT PWM-120-12 PWM-120-24 PWM-120-36 PWM-120-48 DC VOLTAGE 12V 24V 36V 48V RATED CURRENT 10A 5A 3.4A 2.5A RATED POWER 120W 120W 122.4W 120W DIMMING RANGE 0 ~ 100% PWM FREQUENCY (Typ.) 1.47kHz for Blank/DA-Type, 2.5kHz for DA2-Type SETUP, RISE TIME Note.2 Note.9 500ms, 80ms/ 230VAC or 115VAC INPUT HOLD UP TIME (Typ.) 16ms/230VAC or 115VAC VOLTAGE RANGE Note.3 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.97/115VAC, PF>0.96/230VAC, PF>0.93/277VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< 20%(@load60%/115VAC, 230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION" section) EFFICIENCY (Typ.) 88% AC CURRENT (Typ.) 1.3A / 115VAC INRUSH CURRENT (Typ.) COLD START 60A(twidth=520s measured at 50% Ipeak) at 230VAC; Per NEMA 410 90% 0.65A / 230VAC 90% 90.5% 0.55A / 277VAC MAX. NO. of PSUs on 16A 4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT NO LOAD/STANDBY POWER CONSUMPTION OVERLOAD SHORT CIRCUIT PROTECTION OVER VOLTAGE <0.25mA / 277VAC No load power consumption<0.5w for blank-type;standby power consumption<0.5W for DA-type/DA2-type 108 ~ 130% rated output power Hiccup mode, recovers automatically after fault condition is removed 12V/24V hiccup mode and 36V/48V shut down mode(including DA-type/except for DA2-type) Hiccup mode,recovers automatically after fault condition is removed (only for DA2-type) 15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, re-power on to recover WORKING TEMP. Tcase=-40 ~ +90 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=+90 ENVIRONMENT WORKING HUMIDITY 20 ~ 95% RH non-condensing STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 45,except 0 ~ 40 for 12V) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.5 UL8750( type "HL" )(except for 12DA type), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP67,BIS IS15885( for PWM-120-12,24 only), EAC TP TC 004,GB19510.1,GB19510.14 approved; Design refer to EN60335-1; According to EN61347-2-13 appendix J suitable for emergency installations DALI STANDARDS IEC62386-101, 102, 207,251 for DA/DA2-Type only, Device type 6(DT6) SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC; I/P-DA:1.5KVAC; O/P-DA:1.5KVAC EMC ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH EMC EMISSION Note.6 OTHERS NOTE Compliance to EN55015, EN61000-3-2 Class C (@load60%) ; EN61000-3-3,GB17743 and GB17625.1,EAC TP TC 020 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 MTBF 860.4K hrs min. DIMENSION PACKING 191*63*37.5mm (L*W*H) 0.97Kg; 15pcs/15.6Kg/0.87CUFT Telcordia SR-332 (Bellcore) ; 228.7K hrs min. MIL-HDBK-217F (25) , https://www.meanwell.com/serviceDisclaimer.aspx File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver series DIMMING OPERATION AC/L(Brown) AC/N(Blue) DIM+(Blue)* DIM-(White)** +V(Red)(Brown for DA-type) -V(Black)(Blue for DA-type) PWM-120 * DIM+ for Blank-Type DA+ for DA/DA2-type * *DIM- for Blank-Type DA- for DA/DA2-type Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current. ON Output DC current Duty cycle(%) = T ON x100% T Output PWM frequency : 1.47kHz for Blank/DA-Type 2.5kHz for DA2-Type OFF Io=0A T ON T 3 in 1 dimming function (for Blank-Type) Apply one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. Dimming source current from power supply: 100A (typ.) Applying additive 0 ~ 10VDC 100% 90% +V -V + Duty cycle of output current (%) LED Strips + - - DIM+ + Additive Voltage 10% DIM- 70% 60% 50% 40% 30% 20% 10% 0.15% "DO NOT connect "DIM- to -V" 80% 0.6V 0% 0V 1V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): Duty cycle of output current (%) 100% LED Strips +V -V + + - - DIM+ Additive PWM signal DIM"DO NOT connect "DIM- to -V" 10% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0.15% 6% 10% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver Applying additive resistance: 100% 90% -V + Duty cycle of output current (%) LED Strips +V series + - - DIM+ Additive Resistance 10% DIM"DO NOT connect "DIM- to -V" 0.15% 80% 70% 60% 50% 40% 30% 20% 10% 6K/N 10K/N 0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Note : 1. Min. duty cycle of output current is about 0.15%, and the dimming input is about 6K or 0.6VDC, or 10V PWM signal with 6% duty cycle. 2. The duty cycle of output current could drop down to 0% when dimming input is less than 6K or less than 0.6VDC, or 10V PWM signal with duty cycle less than 6%. DALI Interface (primary side; for DA/DA2-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 0.2% of output File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver series OUTPUT LOAD vs TEMPERATURE 100 80 100 80 230VAC Input only 60 60 LOAD (%) 12V only 50 LOAD (%) 230VAC Input only 40 20 -40 -25 0 15 30 40 45 50 60 70 (HORIZONTAL) 40 20 -40 -25 0 20 AMBIENT TEMPERATURE,Ta () 45 65 75 85 90 (HORIZONTAL) Tcase () STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 80 100 90 80 PF LOAD (%) 70 60 50 40 1 .0 0 0 .9 5 0 .9 0 0 .8 5 0 .8 0 0 .7 5 0 .7 0 0 .6 5 0 .6 0 0 .5 5 0 .5 0 0 .4 5 0 .4 0 0 .3 5 0 .3 0 277V 230V 115V 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% (75W) 90 100 125 135 145 155 165 175 180 200 230 305 LOAD INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD PWM-120 series possess superior working efficiency that up to 90.5% can be reached in field applications. 48V Model, Tcase at 80 48V Model, Tcase at 80 30% 20% 277VAC 15% 230VAC 115VAC 10% 5% 0% 50% 60% 70% 80% LOAD 90% 100% EFFICIENCY(%) THD 25% 92 91 90 89 88 87 86 85 84 83 82 81 80 277V 230V 115V 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver series LIFETIME 120 100 LIFETIME(Kh) 80 60 40 20 0 20 30 40 50 60 70 80 90 Tcase( ) File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver Block Diagram I/P series PFC fosc : 50~120KHz PWM fosc : 60~130KHz EMI FILTER & RECTIFIERS +V RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT DIMMING CIRCUIT -V O.L.P. O.T.P. O.L.P. DIM+ DIM- DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. Mechanical Specification Case No. PWM-120 Unit:mm Blank-Type 30020 30020 191 5 5 T case tc UL2464 18AWGx2C DIM+(Blue) DIM-(White) +V(Red) -V(Black) 95.5 31.5 2- SJTW 18AWGx2C 5 4. 5 63 503 AC/L(Brown) AC/N(Blue) SJTW 14AWGx2C 503 5 : Max. Case Temperature 3 37.5 tc DA/DA2-Type 30020 30020 191 5 5 UL2464 18AWGx2C DA+(Blue) DA-(White) +V(Brown) -V(Blue) 95.5 2- 31.5 T case tc SJOW 17AWGx2C &H05RN-F 1.0mm 2 5 : Max. Case Temperature 37.5 tc 503 3 SJOW 17AWGx2C &H05RN-F 1.0mm 2 5 4. 5 63 503 AC/L(Brown) AC/N(Blue) File Name:PWM-120-SPEC 2021-04-1 PWM-120 120W PWM Output LED Driver series Recommend Mounting Direction Installation Manual Connection for Blank-type DIM-(WHITE) + AC/L(BROWN) 0~10Vdc or 10V PWM or resistance Dimmer or DALI Dimmer DIM+(BLUE) AC/N(BLUE) -V(BLACK) + LED Strip +V(RED) Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM- to -V". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. For more information about installation, Please refer to : http://www.meanwell.com/manual.html for details. File Name:PWM-120-SPEC 2021-04-1