SCLS104D - MARCH 1984 - REVISED AUGUST 2003 D Wide Operating Voltage Range of 2 V to 6 V D High-Current 3-State Outputs Interface D Directly With System Bus or Can Drive Up To 15 LSTTL Loads Low Power Consumption, 80-A Max ICC SN54HC125 . . . FK PACKAGE (TOP VIEW) 1 14 2 13 3 12 11 5 10 6 9 7 8 VCC 4OE 4A 4Y 3OE 3A 3Y 1Y NC 2OE NC 2A 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4A NC 4Y NC 3OE 2Y GND NC 3Y 3A 4 1A 1OE NC VCC 4OE SN54HC125 . . . J OR W PACKAGE SN74HC125 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) 1OE 1A 1Y 2OE 2A 2Y GND D Typical tpd = 11 ns D 6-mA Output Drive at 5 V D Low Input Current of 1 A Max NC - No internal connection description/ordering information These quadruple bus buffer gates feature independent line drivers with 3-state outputs. Each output is disabled when the associated output-enable (OE) input is high. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PACKAGE TA PDIP - N SN74HC125N Tube of 50 SN74HC125D Reel of 2500 SN74HC125DR Reel of 250 SN74HC125DT SOP - NS Reel of 2000 SN74HC125NSR HC125 SSOP - DB Reel of 2000 SN74HC125DBR HC125 Reel of 2000 SN74HC125PWR Reel of 250 SN74HC125PWT CDIP - J Tube of 25 SNJ54HC125J SNJ54HC125J CFP - W Tube of 150 SNJ54HC125W SNJ54HC125W LCCC - FK Tube of 55 SNJ54HC125FK TSSOP - PW -55C -55 C to 125 125C C TOP-SIDE MARKING Tube of 25 SOIC - D -40C to 85C ORDERABLE PART NUMBER SN74HC125N HC125 HC125 SNJ54HC125FK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !"#$ % &'!!($ #% )'*+&#$ ,#$(!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($% %$#,#!, 0#!!#$1- !,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2 #++ )#!#"($(!%- )!,'&$% &")+#$ $ 34 #++ )#!#"($(!% #!( $(%$(, '+(%% $.(!0%( $(,- #++ $.(! )!,'&$% )!,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2 #++ )#!#"($(!%- POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCLS104D - MARCH 1984 - REVISED AUGUST 2003 FUNCTION TABLE (each buffer) INPUTS OE A OUTPUT Y L H H L L L H X Z logic diagram (positive logic) 1OE 1A 2OE 2A 1 2 3OE 3 1Y 3A 4 5 4OE 6 2Y 4A 10 9 8 3Y 13 12 11 4Y Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 mA Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS104D - MARCH 1984 - REVISED AUGUST 2003 recommended operating conditions (see Note 3) SN54HC125 VCC VIH Supply voltage VCC = 2 V VCC = 4.5 V High-level input voltage VCC = 6 V VCC = 2 V VIL VI VO t/v MIN NOM MAX 2 5 6 Input voltage MAX 2 5 6 3.15 3.15 4.2 4.2 0 VCC = 6 V UNIT V V 0.5 0.5 1.35 1.35 1.8 1.8 VCC VCC VCC = 2 V VCC = 4.5 V Input transition rise/fall time NOM 1.5 0 Output voltage MIN 1.5 VCC = 4.5 V VCC = 6 V Low-level input voltage SN74HC125 0 VCC VCC 0 1000 1000 500 500 400 400 V V V ns TA Operating free-air temperature -55 125 -40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS VI = VCC or 0, MIN MAX SN74HC125 MIN MAX UNIT 1.9 1.998 1.9 1.9 IOH = -20 A 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 IOH = -6 mA IOH = -7.8 mA 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 5.34 2V 0.002 0.1 0.1 0.1 IOL = 20 A 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V 0.1 100 1000 1000 nA 6V 0.01 0.5 10 5 A 8 160 80 A 10 10 10 pF IOL = 6 mA IOL = 7.8 mA ICC Ci SN54HC125 2V VI = VIH or VIL VI = VCC or 0 VO = VCC or 0 TA = 25C MIN TYP MAX 4.5 V VI = VIH or VIL II IOZ VCC IO = 0 6V 2 V to 6 V POST OFFICE BOX 655303 3 * DALLAS, TEXAS 75265 V V 3 SCLS104D - MARCH 1984 - REVISED AUGUST 2003 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) TA = 25C TYP MAX SN54HC125 SN74HC125 PARAMETER FROM (INPUT) TO (OUTPUT) VCC 2V 48 120 150 150 tpd A Y 4.5 V 14 24 36 30 6V 11 20 25 26 ten OE tdis Y OE Y tt Any MIN MIN MAX MIN MAX 2V 53 120 180 150 4.5 V 14 24 36 30 6V 11 20 31 26 2V 30 120 180 150 4.5 V 15 24 36 30 6V 14 20 31 26 2V 28 60 90 75 4.5 V 8 12 18 15 6V 6 10 15 13 UNIT ns ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 150 pF (unless otherwise noted) (see Figure 1) PARAMETER tpd ten FROM (INPUT) TA = 25C MIN TYP MAX SN54HC125 SN74HC125 TO (OUTPUT) VCC 2V 67 150 225 190 Y 4.5 V 19 30 45 38 6V 15 25 39 32 2V 100 135 200 170 4.5 V 20 27 40 34 6V 17 23 34 29 2V 45 210 315 265 4.5 V 17 42 63 53 6V 13 36 53 45 A OE Y tt Any MIN MAX MIN MAX UNIT ns ns ns operating characteristics, TA = 25C PARAMETER Cpd 4 TEST CONDITIONS Power dissipation capacitance per gate POST OFFICE BOX 655303 No load * DALLAS, TEXAS 75265 TYP 45 UNIT pF SCLS104D - MARCH 1984 - REVISED AUGUST 2003 PARAMETER MEASUREMENT INFORMATION VCC PARAMETER Test Point From Output Under Test S1 tPZH ten RL CL (see Note A) 1 k tPZL tPHZ tdis S2 RL 1 k CL S1 S2 50 pF or 150 pF Open Closed Closed Open Open Closed Closed Open Open Open 50 pF tPLZ tpd or tt -- LOAD CIRCUIT 50 pF or 150 pF VCC Input 50% 50% 0V tPLH In-Phase Output 50% 10% tPHL 90% VOH 50% 10% V OL tf 90% tr tPHL Out-of-Phase Output 90% tPLH 50% 10% 50% 10% 90% VOH VOL tf tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES Output Control (Low-Level Enabling) VCC 50% 50% 0V tPZL Output Waveform 1 (See Note B) tPLZ 10% tPZH Input 50% 10% 90% VCC 90% 50% 10% 0 V tr Output Waveform 2 (See Note B) VCC VCC 50% VOL tPHZ 50% 90% VOH 0 V tf VOLTAGE WAVEFORM INPUT RISE AND FALL TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES FOR 3-STATE OUTPUTS NOTES: A. CL includes probe and test-fixture capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr = 6 ns, tf = 6 ns. D. The outputs are measured one at a time with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-8772101CA ACTIVE CDIP J 14 1 TBD Call TI Call TI SN54HC125J ACTIVE CDIP J 14 1 TBD SN74HC125D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) SN74HC125DBLE OBSOLETE SSOP DB 14 SN74HC125DBR ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DBRE4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DBRG4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125DTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 25 Pb-Free (RoHS) TBD SN74HC125N ACTIVE PDIP N 14 SN74HC125N3 OBSOLETE PDIP N 14 SN74HC125NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) SN74HC125NSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) TBD Addendum-Page 1 N / A for Pkg Type CU NIPDAU Level-1-260C-UNLIM Call TI Call TI CU NIPDAU N / A for Pkg Type Call TI Samples (Requires Login) 5962-87721012A A42 (3) Call TI CU NIPDAU N / A for Pkg Type CU NIPDAU Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 5-Sep-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) SN74HC125NSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125NSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWT ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWTE4 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC125PWTG4 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54HC125FK ACTIVE LCCC FK 20 1 TBD SNJ54HC125J ACTIVE CDIP J 14 1 TBD POST-PLATE N / A for Pkg Type A42 N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54HC125, SN74HC125 : * Catalog: SN74HC125 * Automotive: SN74HC125-Q1, SN74HC125-Q1 * Military: SN54HC125 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 20-Aug-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74HC125DBR SSOP DB 14 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 SN74HC125DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN74HC125DT SOIC D 14 250 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN74HC125NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN74HC125PWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 SN74HC125PWT TSSOP PW 14 250 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Aug-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74HC125DBR SSOP DB 14 2000 346.0 346.0 33.0 SN74HC125DR SOIC D 14 2500 346.0 346.0 33.0 SN74HC125DT SOIC D 14 250 346.0 346.0 33.0 SN74HC125NSR SO NS 14 2000 346.0 346.0 33.0 SN74HC125PWR TSSOP PW 14 2000 346.0 346.0 29.0 SN74HC125PWT TSSOP PW 14 250 346.0 346.0 29.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connctivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated