EH1300HSTS-100.000M-G TR EH13 00 HS RoHS Pb TS -100.000M - G TR Series RoHS Compliant (Pb-free) 3.3V 8 Pin DIP Metal Thru-Hole LVCMOS High Frequency Oscillator Packaging Options Tape & Reel Gull Wing Gull Wing Frequency Tolerance/Stability 100ppm Maximum Value Added Option Prefix Package Operating Temperature Range 0C to +70C Duty Cycle 50 10(%) Nominal Frequency 100.000MHz Pin 1 Connection Tri-State (Disabled Output: High Impedance) ELECTRICAL SPECIFICATIONS Nominal Frequency 100.000MHz Frequency Tolerance/Stability 100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Ouput Load Change, 1st Year Aging at 25C, Shock, and Vibration.) Aging at 25C 5ppm/year Maximum Operating Temperature Range 0C to +70C Supply Voltage 3.3Vdc 0.3Vdc Input Current 35mA Maximum (No Load) Output Voltage Logic High (Voh) 2.7Vdc Minimum (IOH = -8mA) Output Voltage Logic Low (Vol) 0.5Vdc Maximum (IOL = +8mA) Rise/Fall Time 4nSec Maximum (Measured at 20% to 80% of waveform) Duty Cycle 50 10(%) (Measured at 50% of waveform) Load Drive Capability 15pF Maximum Output Logic Type CMOS Pin 1 Connection Tri-State (Disabled Output: High Impedance) Tri-State Input Voltage (Vih and Vil) 70% of Vdd Minimum to enable output, 20% of Vdd Maximum to disable output (High Impedance), No Connect to enable output. Absolute Clock Jitter 250pSec Maximum, 100pSec Typical One Sigma Clock Period Jitter 50pSec Maximum, 40pSec Typical Start Up Time 10mSec Maximum Storage Temperature Range -55C to +125C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS Fine Leak Test MIL-STD-883, Method 1014, Condition A Gross Leak Test MIL-STD-883, Method 1014, Condition C Lead Integrity MIL-STD-883, Method 2004 Mechanical Shock MIL-STD-202, Method 213, Condition C Resistance to Soldering Heat MIL-STD-202, Method 210 Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010 Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 1 of 6 EH1300HSTS-100.000M-G TR MECHANICAL DIMENSIONS (all dimensions in millimeters) 7.620 0.203 1 7.620 0.203 8 0.8 0.1 (X3) 4 DIA 0.457 0.1 (X4) 5 PIN CONNECTION 1 Tri-State (High Impedance) 4 Case/Ground 5 Output 8 Supply Voltage LINE MARKING 5.08 MIN 5.6 MAX 13.2 MAX MARKING ORIENTATION 1 ECLIPTEK 2 EH13TS EH13=Product Series 3 100.00M 4 XXYZZ XX=Ecliptek Manufacturing Code Y=Last Digit of the Year ZZ=Week of the Year 13.2 MAX CLOCK OUTPUT TRI-STATE INPUT OUTPUT WAVEFORM & TIMING DIAGRAM VIH VIL VOH 80% of Waveform OUTPUT DISABLE (HIGH IMPEDANCE STATE) 50% of Waveform 20% of Waveform VOL tPLZ Fall Time Rise Time tPZL TW T Duty Cycle (%) = TW/T x 100 www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 2 of 6 EH1300HSTS-100.000M-G TR Test Circuit for CMOS Output Frequency Counter Oscilloscope + + Power Supply _ Current Meter _ Supply Voltage (VDD) Probe (Note 2) Output + Voltage Meter _ 0.01F (Note 1) 0.1F (Note 1) Ground CL (Note 3) No Connect or Tri-State Note 1: An external 0.1F low frequency tantalum bypass capacitor in parallel with a 0.01F high frequency ceramic bypass capacitor close to the package ground and VDD pin is required. Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>300MHz) passive probe is recommended. Note 3: Capacitance value CL includes sum of all probe and fixture capacitance. www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 3 of 6 EH1300HSTS-100.000M-G TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak tP Time (t) High Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 3C/second Maximum 150C 175C 200C 60 - 180 Seconds 3C/second Maximum 217C 60 - 150 Seconds 260C Maximum for 10 Seconds Maximum 250C +0/-5C 20 - 40 seconds 6C/second Maximum 8 minutes Maximum Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 4 of 6 EH1300HSTS-100.000M-G TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak tP Time (t) Low Temperature Infrared/Convection 185C TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 5C/second Maximum N/A 150C N/A 60 - 120 Seconds 5C/second Maximum 150C 200 Seconds Maximum 185C Maximum 185C Maximum 2 Times 10 seconds Maximum 2 Times 5C/second Maximum N/A Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 5 of 6 EH1300HSTS-100.000M-G TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak tP Time (t) Low Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 5C/second Maximum N/A 150C N/A 30 - 60 Seconds 5C/second Maximum 150C 200 Seconds Maximum 245C Maximum 245C Maximum 1 Time / 235C Maximum 2 Times 5 seconds Maximum 1 Time / 15 seconds Maximum 2 Times 5C/second Maximum N/A Level 1 Low Temperature Manual Soldering 185C Maximum for 10 seconds Maximum, 2 times Maximum. High Temperature Manual Soldering 260C Maximum for 5 seconds Maximum, 2 times Maximum. www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 2/19/2010 | Page 6 of 6