95
Subminiature Basic Switch SSG
Subminiature Basic Switch Conforming
to EN61058-1 (IEC1058-1), UL1054, and
CSA C22.2 No.54
A wide operating temperature range of –25°C to
125°C is available for at high-temperature use.
A wide variety of terminals:
Solder, Tab (#110), and PCB Terminal Models.
PCB T
erminal Models are resistant to flux.
Ordering Information
Actuator Rating OF
max.
Solder
(see note)
T
ab (#1
10) PCB
(see note)
Pin plunger
0.1 A
1.50 N
SSG-01H SSG-01T SSG-01P
pu ge
0.50 N
SSG-01H-5 SSG-01T-5 SSG-01P-5
5 A
1.50 N
SSG-5H SSG-5T SSG-5P
0.50 N
SSG-5H-5 SSG-5T-5 SSG-5P-5
Hinge lever
0.1 A
0.60 N
SSG-01L1H SSG-01L1T SSG-01L1P
geee
0.20 N
SSG-01L1H-5 SSG-01L1T-5 SSG-01L1P-5
5 A
0.60 N
SSG-5L1H SSG-5L1T SSG-5L1P
0.20 N
SSG-5L1H-5 SSG-5L1T-5 SSG-5L1P-5
Simulated hinge lever
0.1 A
0.60 N
SSG-01L3H SSG-01L3T SSG-01L3P
S uaed geee
0.20 N
SSG-01L3H-5 SSG-01L3T-5 SSG-01L3P-5
5 A
0.60 N
SSG-5L3H SSG-5L3T SSG-5L3P
0.20 N
SSG-5L3H-5 SSG-5L3T-5 SSG-5L3P-5
Hinge roller lever
0.1 A
0.60 N
SSG-01L2H SSG-01L2T SSG-01L2P
geoe ee
0.20 N
SSG-01L2H-5 SSG-01L2T-5 SSG-01L2P-5
5 A
0.60 N
SSG-5L2H SSG-5L2T SSG-5L2P
0.20 N
SSG-5L2H-5 SSG-5L2T-5 SSG-5L2P-5
Note:
EN61058-1 (IEC1058-1) approved by TÜV Rheinland.
Back
SSG SSG
96
Specifications
Ratings
1. General Ratings
Non-inductive
load Inductive laod
Resistive load
Lamp load
Inductive load
Motor load
Rated voltage
NC NO NC NO NC NO NC NO
125 V
AC
5 (0.1) A (see note 1)
1.5 A 0.7 A
3 A
2.5 A 1.3 A
250 V
AC
3 A 1 A
0.5 A
2 A
1.5 A 0.8 A
8 VDC
5 A 2 A 5 A 3 A
14 VDC
5 A 2 A 4 A 3 A
30 VDC
4 (0.1) A (see note 1)
2 A 3 A 3 A
125 VDC
0.4 A
0.05 A
0.4 A
0.05 A
250 VDC
0.2 A
0.03 A
0.2 A
0.05 A
Note: 1.
The values in the parentheses are for the SSG-01.
2.
The above current ratings are the values of the steady-state current.
3.
Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC).
4.
Lamp load has an inrush current of 10 times the steady-state current.
5.
Motor load has an inrush current of 6 times the steady-state current.
6.
If the switch is used in a DC circuit and is subjected to a surge current, connect a surge suppressor across the switch.
2. TÜV Rheinland Approved Rating (EN61058-1/IEC1058-1)
SSG-5 series:
5 A at 250 V
AC (T125, 50,000 operations)
SSG-01 series:
0.1 A at 30 VDC (T125, 50,000 operations)
3. UL, CSA Approved Rating
SSG-5 series:
5 A at 125 V
AC, 3 A at 250 VAC (6,000 operations)
SSG-01 series:
0.1 A at 125 V
AC, 0.1 A at 30 VDC (6,000 operations)
Characteristics
Operating
speed
0.1 mm to 1 m/s (at pin plunger)
Operating frequency
Mechanical:
400 operations/min
Electrical:
60 operations/min
Insulation resistance
100 M
Ω
min.
Contact resistance
OF 1.50 N:
SSG-5 series:
30 m
Ω
max.
SSG-01 series:
50 m
Ω
max.
OF 0.50 N
SSG-5 series:
50 m
Ω
max.
SSG-01 series:
100 m
Ω
max.
Dielectric strength
1,000 V
AC, 50/60 Hz for 1 min between contacts of the same polarity
(600 V
AC for SSG-01H and SSG-01T series)
1,500 V
AC, 50/60 Hz for 1 min between each terminal and ground
1,500 V
AC, 50/60 Hz for 1 min between each terminal and non-current-carrying metal part
Inrush current
SSG-5: NO:
20 A max.
NC:
10 A max.
SSG–01: NO:
1 A max.
NC:
1 A max.
V
ibration resistance
Malfunction: 10 to 2,000 Hz, 196 m/s
2
(20G) (Contact open: 10
µ
s max., lever position: at TTP)
Shock resistance
Malfunction: 490 m/s
2
(approx. 50G) (Contact open: 10
µ
s max., lever position: at TTP)
Life expectancy
Mechanical:
10,000,000 operations min. (OT
: rated value)
Electrical:
200,000 operations min. (5 A at 125 V
AC for SSG-5, 0.1 A at 125 V
AC for SSG-01,
resistive OT:full)
Degree of protection (IP code)
IP00 (IEC1058-1)
Degree of protection against
electrical shock
Class I (IEC1058-1)
Proof tracking index
175 V (IEC1058-1)
Switch category (IEC335-1)
D (IEC1058-1)
SSG SSG
97
Contact
Item SSG-5 SSG-01
Specification Rivet Crossbar
Material Silver PGS
alloy
Safety Standards
Certification
body
Standard
File no.
TÜV Rheinland
EN61058-1 (IEC1058-1)
T9451449
UL UL1054 E32667
CSA
C22.2 No.54
LR21642
Operating Characteristics
Solder/Tab Terminal
Type Pin
plunger
Hinge lever
Simulated hinge lever
Hinge roller lever
SSG-01j
SSG-5jSSG-01j-5
SSG-5j-5 SSG-01L1j
SSG-5L1jSSG-01L1j-5
SSG-5L1j-5 SSG-01L3j
SSG-5L3jSSG-01L3j-5
SSG-5L3j-5 SSG-01L2j
SSG-5L2jSSG-01L2j-5
SSG-5L2j-5
OF max.
1.50 N
(153 gf)
0.50 N
(51 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
RF min.
0.25 N
(25 gf)
0.04 N
(4 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf)
PT max.
0.6 mm 1.0 mm 1.0 mm 1.0 mm
OT min.
0.4 mm 0.8 mm 0.8 mm 0.8 mm
MD max.
0.1 mm
--- --- ---
FP max.
---
13.6 mm 15.5 mm 19.0 mm
OP 8.4±
0.3 mm
8.8+1.0/–0.6
mm
10.7+1.0/–0.6
mm
14.5+1.0/–0.6
mm
PCB Terminal
Type Pin
plunger
Hinge lever
Simulated hinge lever
Hinge roller lever
SSG-01P
SSG-5P SSG-01P-5
SSG-5P-5 SSG-01L1P
SSG-5L1P SSG-01L1P-5
SSG-5L1P-5 SSG-01L3P
SSG-5L3P SSG-01L3P-5
SSG-5L3P-5 SSG-01L2P
SSG-5L2P SSG-01L2P-5
SSG-5L2P-5
OF max.
1.50 N
(153 gf)
0.50 N
(51 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
0.60 N
(61 gf) 0.20 N (20 gf)
RF min.
0.25 N
(25 gf)
0.04 N
(4 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf)
PT max.
0.6 mm 1.0 mm 1.0 mm 1.0 mm
OT min.
0.4 mm 0.8 mm 0.8 mm 0.8 mm
MD max.
0.1 mm
--- --- ---
FP max.
---
17.0 mm 18.9 mm 22.4 mm
OP 11.8±
0.4 mm
12.2+1.1/–0.7
mm
14.4+1.1/–0.7
mm
17.9+1.1/–0.7
mm
SSG SSG
98
Dimensions
Note: 1.
All units are in millimeters unless otherwise indicated.
2.
Every actual model number includes the code instead of
j
for the kind of terminals incorporated by the model.
3.
Unless otherwise specified, a tolerance of
±
0.4 mm applies to all dimensions.
Terminal Model
Solder/Tab Terminal
Pin Plunger
SSG-01j
SSG-5j
SSG-01j-5
SSG-5j-5
2.2+0.1
0
1.8
7.5±0.3
2.2
2.5 dia.
5.1 8.9
(see note) 7.2
(see note)
9.5±0.1
0.5
6.9 7.7
3.5
3.2
6.4±0.2 Three, 1.6 dia. holes
Note: At
switch bottom
6.1
19.8
2.2+0.1
0 dia. hole
CNONC
1.6
(see note)
PT
OP
Hinge Lever
SSG-01L1j
SSG-5L1j
SSG-01L1j-5
SSG-5L1j-5
Simulated Hinge Lever
SSG-01L3j
SSG-5L3j
SSG-01L3j-5
SSG-51L3j-5
8.9
(see note)
6.9
5.3±0.4
6.9 7.7
t0.3 Stainless lever
2.2+0.1
0
3.6
6.1
2.2
5.1
2.5 dia.
7.2
(see note) 0.5
Note: At
switch bottom
9.5±0.1
2.2 +0.1
0 dia. hole 3.2
6.4+0.2 Three, 1.6 dia. holes
CNONC
3.2
6.4±0.2 Three, 1.6 dia. holes
7.7
6.1
2.2
19.8
5.1
2.5 dia.
t0.3 Stainless lever
0.5
Note: At
switch bottom
9.5±0.1
3.6
2.2+0.1
0 dia. hole
R
1.3
6.3±0.4
19.8
CNONC
8.9
(see note) 7.2
(see note)
1.6
(see note)
2.2+0.1
0
1.6
(see note)
OP FP
OP FP
SSG SSG
99
Hinge Roller Lever
SSG-01L2j
SSG-5L2j
SSG-01L2j-5
SSG-5L2j-5 3.8
5±0.4
6.9 7.7
6.1
2.2
3.2
6.4±0.2
19.8
5.1
2.5 dia.
t0.3 Stainless lever
0.5
Note: At
switch bottom
4.8
× 3.2 dia.
Acetal resin roller
9.5±0.1
2.2+0.1
–0
Three, 1.6 dia. holes
CNONC
8.9
(see note) 7.2
(see note)
1.6
(see note)
2.2+0.1
0 dia. hole
OP FP
PCB Terminal
Pin Plunger
SSG-01P
SSG-5P
SSG-01P-5
SSG-5P-5
Hinge Lever
SSG-01L1P
SSG-5L1P
SSG-01L1P-5
SSG-5L1P-5
C
1.3±0.3
0.5±0.05
6.4±0.2
2.87±0.1
4.8±0.3
3.4±0.1
2.5 dia.
5.15
7.62±0.2
1.8
7.62±0.2
3.5
4±0.3
1.8
Three, 1.2±0.1
Three, 0.8
7.7
NC
NO
2.2+0.1
–0
19.8
6.9
2.2+0.1
0 dia. hole
9.5±0.1
PT
OP
6.9
5.3±0.4
19.8
5.15
2.5 dia.
t0.3 Stainless lever
7.62±0.2
3.4±0.1
2.2+0.1
0
2.87±0.1
9.5±0.1 7.62±0.2
Three, 0.8
Three, 1.2±0.1
CNC
NO
1.3±0.3
0.5±0.05
6.4±0.2 4±0.3
3.6
7.7
2.2+0.1
0 dia. hole 1.8
OPFP
SSG SSG
100
Simulated Hinge Lever
SSG-01L3P
SSG-5L3P
SSG-01L3P-5
SSG-51L3P-5
2.2+0.1
0 dia. hole
6.9
Three,
1.2
±0.1
t0.3 Stainless lever R 1.3 6.3±0.4
7.7
19.8
5.15
2.5 dia.
7.62±0.2
3.4±0.1
2.2+0.1
0
2.87±0.1
9.5±0.1 7.62±0.2
Three, 0.8
NO
1.3±0.3
0.5±0.05
6.4±0.2 1.84±0.3
3.6
CNC
OP FP
Hinge Roller Lever
SSG-01L2P
SSG-5L2P
SSG-01L2P-5
SSG-5L2P-5
Three,
1.2
±0.1
6.9
NO
4.8
× 3.2 dia.
Acetal resin roller
1.3±0.3
0.5±0.05
6.4±0.2
1.84±0.3
5±0.4
19.8
5.15
2.5 dia.
t0.3 Stainless lever
7.62±0.2
3.4±0.1
2.87±0.1
9.5±0.1 7.62±0.2
Three, 0.8
CNC
2.2+0.1
0
Three, 1.2±0.1
3.8
2.2+0.1
0 dia. hole
OP FP
7.7
SSG SSG
101
Kind of Terminals
Solder Terminals Tab Terminals (#110)
PCB Terminals
PCB
Mounting
2.2+0.1
0
1.8
7.5±0.3
2.2
2.5 dia.
5.1 8.9
(see note) 7.2
(see note)
9.5±0.1
0.5
6.9 7.7
3.5
3.2
6.4±0.2
Three, 1.6 dia. holes
Note: At
switch bottom
6.1
19.8
2.2+0.1
0 dia. hole
CNONC
1.6
(see note)
PT
OP 2.2+0.1
0
1.8
7.5±0.3
2.2
2.5 dia.
5.1 9.5±0.1
0.5
19.8
6.9 7.7
3.5
3.2
6.4±0.2
Three,
1.2 dia.
holes
Note: At
switch bottom
2.8±0.2
10.6
NO NC
7.2
(see note)
7.1
2.2+0.1
0 dia. hole
8.9
(see note)
1.6
(see note)
C
PT
OP
2.78±0.1
C
1.3±0.3
0.5±0.05
6.4±0.2
2.87±0.1
4.8±0.3
3.4±0.1
2.5 dia.
5.15
7.62±0.2
1.8
7.62±0.2
3.5
4±0.3
1.8
Three, 1.2±0.1
Three, 0.8
7.7
NC
NO 7.62±0.1
9.5±0.1
Three, 1.35 dia. to 1.5 dia.
2.2+0.1
–0
19.8
6.9
15.24±0.1
2.2+0.1
0 dia. hole
9.5±0.1
PT
OP
SSG SSG
102
Precautions
Mounting
Use two 2.2 mounting screws with spring washers to mount the
switch. Tighten the screws to a torque of 0.20 to 0.25 N S m (2 to
2.5 kgf
S cm).
Mounting Holes
9.5±0.1
The
switch does not have a ground terminal. The minimum
distance
through insulation
(IEC1058-1) is 0.9 mm. If proper insulation for the
end
product cannot be secured, additional insulation such as a sep
-
arator
or insulation cover should be attached.
Soldering
When soldering switch terminals, apply a soldering iron rated at
60 W
max. and finish soldering quickly within 3
seconds. During sol
-
dering and 1 minute after soldering, do not apply external force to
the
terminals.
Solder terminal is provided with a hole so that a conductor can be
secured mechanically
.
The
conductors
for a soldering terminal (H type) should be flexible
and
its cross section should be A
WG18 to 20 for the SSG-5H Series
and
A
WG20 to 22 for the SSG-01H Series.
To
automatically solder the
switch to a PCB in a soldering bath, com
-
plete
soldering within 5 seconds
at a flux temperature of 250
°
C and
avoid the overflow of flux onto the surface of the PCB where the
switch
or other parts are mounted.
Actuating
Make sure that the operating speed and frequency are within the
permissible
range of the switch.
1. Do not use the switch in an application where the operating
speed is extremely slow or the switching operation could
become unstable or malfunctioning could result due to
contact
failure or contact welding.
2. Do not use the switch in an application where the operating
speed
is too fast, or the switch will be broken
due to a shock or
the
movable contact will not keep up with the speed.
The
reliability of a switch is maintained within the permissible oper
-
ating
speed and frequency of the switch. The life of a switch is deter
-
mined
at a specified operating
speed, therefore, it varies with the ac
-
tual
operating speed and frequency
.
The
switch should be set so that its stroke will be in the range of 60%
to
90% of the rated OT when the switch is operated. The stroke must
not
exceed the rated OT value.
Malfunctioning
can result if the switch is set with its stroke exceed
-
ing
the rated OT
. Therefore the proper adjustment of the
mounting
position
is essential when installing the switch.
Do
not apply excessive force to the actuator
. Be very careful not to
apply
force in
the opposite and lateral directions relative to the oper
-
ating
direction.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To
convert millimeters into inches, multiply by 0.03937. T
o convert grams into ounces, multiply by 0.03527.
Cat. No. B096-E1-1
