8 7 6 5 4 3 VICOR CONFIDENTIAL THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. F SEE NOTE 6 <> .16 TYP (12) PL. SEE NOTE 5 <> #30 DRILL THRU ( .1285 ) (6) PL. 2 1 REV. DESCRIPTION DATE APPROVED 1 RELEASED PER ECO REQUEST E070416 REJH 03/05/07 EF 2 REVISED PER ECO REQUEST E091085 AR 07/14/09 REJH 3 REDRAWN PER E100871 DCS 6/11/10 KUK 4 REVISED PER E120702 ZMB 07/31/12 REJH .40 F .010 MATL TO BE REMOVED E E 2.000 <> 2.220 D D .11 .190 1.800 <> -A3.600 <> .50 .100 <> 4.60 .005 C C .410 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. <> 3. CLEAR FINISH, RoHS COMPLIANT PER CST-0001, LATEST REVISION PER A.) CHROMIUM FREE, OR B.) TRIVALENT CHROMIUM IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASS 1A OR 3. SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. 4. "<>" DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION.' 5. DIMENSIONS APPLIES AT SURFACE -A- (12) PL. 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. 7. DIMENSIONS ARE INCHES ONLY. A DRAWN BY DATE D.P. KELLY 10/05 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / [MM] TOLERANCES ARE: DECIMALS ANGLES X.XX [X.X] = 0.01 [0.25] 1 X.XXX [X.XX] = 0.005 [0.127] THIRD ANGLE PROJECTION DO NOT SCALE DRAWING 8 7 6 5 4 3 VICOR SWD HS CFG 'A' LONG .4H LOW FLOW, THRU HOLE SIZE C CAGE CODE SCALE 1:1 2 67131 DWG NO REV 30718 4 SHEET 1 OF 2 1 A 8 7 6 5 4 3 2 1 REVISIONS VICOR CONFIDENTIAL THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. REV DATE DESCRIPTION APPROVED SEE SHEET 1 F E F E R.035 (24) PL. SEE DETAIL A A 3.00 1.5 EACH SIDE OF VERT R.035 .410 .200 .235 .110 D 1.756 * .133 (9) PL. * .060 (8) PL. * .138 (2) PL. R.010 (2) PL. R.018 (2) PL. * .058 (2) PL. * .269 D .023 .036 .031 +.020 2.220 - .000 .040 .017 (2) PL. .080 R.030 (8) PL. C .252 C * .030 * .060 PROFILE COMMON FOR B DETAIL A SCALE 8 : 1 30195 30718 32188 30482 NOTES: 1. MATL: ALUMINUM 6063-T5 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. DIMENSIONS ARE INCHES ONLY DRAWN BY DATE A. RAGIPANI 07/14/09 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / [MM] TOLERANCES ARE: DECIMALS ANGLES X.XX [X.X] = 0.01 [0.25] 1 X.XXX [X.XX] = 0.005 [0.127] A THIRD ANGLE PROJECTION DO NOT SCALE DRAWING 8 7 6 B 5 4 3 VICOR SWD HS CFG "A" LONG .4H LOW FLOW, THRU HOLE, EXTRUSION SIZE CAGE CODE C 67131 SCALE 1:1 2 DWG NO REV 30718 4 SHEET 2 OF 2 1 A