ADS2807 ADS 280 7 SBAS169B - NOVEMBER 2000 - REVISED MAY 2002 Dual, 12-Bit, 50MHz Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES APPLICATIONS HIGH SNR: 66dB (2Vp-p), 68dB (3Vp-p) LOW POWER: 720mW INTERNAL OR EXTERNAL REFERENCE LOW DLE: 0.6LSB FLEXIBLE INPUT RANGE: 2Vp-p to 3Vp-p TQFP-64 POWER PACKAGE DESCRIPTION COMMUNICATIONS IF PROCESSING COMMUNICATIONS BASESTATIONS TEST EQUIPMENT MEDICAL IMAGING VIDEO DIGITIZING CCD DIGITIZING The ADS2807 provides an over-range indicator flag to indicate an input signal that exceeds the full-scale input range of the converter. This flag can be used to reduce the gain of front-end gain control circuitry. There is also an output enable pin to allow for multiplexing and testability on a PC board. The ADS2807 is a dual, high-speed, high dynamic range, 12-bit pipelined Analog-to-Digital Converter (ADC). This converter includes a high-bandwidth track-and-hold that gives excellent spurious performance up to and beyond the Nyquist rate. The differential nature of this track-and-hold and ADC circuitry minimizes even-order harmonics and gives excellent common-mode noise immunity. The trackand-hold can also be operated single-ended. The ADS2807 employs digital error correction techniques to provide excellent differential linearity for demanding imaging applications. The ADS2807 is available in a TQFP-64 power package. The ADS2807 provides for setting the full-scale range of the converter without any external reference circuitry. The internal reference can be disabled allowing low-drive, external references to be used for improved tracking in multichannel systems. +VS CMA VIN ADS2807 INA 12-Bit Pipelined ADC T&H INA (Opt.) INT/EXT Internal Reference FSSEL VIN INB T&H INB (Opt.) OEA OVRA Error Correction Logic 3-State Outputs Timing Circuitry 12-Bit Pipelined ADC Error Correction Logic D12A * * * D1A CLK 3-State Outputs D12B * * * D1B CMB Optional External Reference OEB OVRB Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright (c) 2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS(1) +VS ....................................................................................................... +6V Analog Input ........................................................... (-0.3V) to (+VS + 0.3V) This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. Logic Input ............................................................. (-0.3V) to (+VS + 0.3V) Case Temperature ......................................................................... +100C Junction Temperature .................................................................... +150C Storage Temperature ..................................................................... +150C ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. PACKAGE/ORDERING INFORMATION SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR(1) ADS2807Y TQFP-64 PAP -40C to +85C ADS2807Y ADS2807Y/1K5 Tape and Reel, 1500 " " " " ADS2807Y/250 Tape and Reel, 250 " NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com. ELECTRICAL CHARACTERISTICS At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MHz, unless otherwise noted. ADS2807Y PARAMETER CONDITIONS MIN RESOLUTION SPECIFIED TEMPERATURE RANGE ANALOG INPUT 2V Full-Scale Input Range 2V Full-Scale Input Range 3V Full-Scale Input Range 3V Full-Scale Input Range Analog Input Bias Current Analog Input Bandwidth Input Impedance TYP MAX 12 Tested (Differential) (Single-Ended) (Differential) (Single-Ended) Ambient Air 2Vp-p, 2Vp-p, 3Vp-p, 3Vp-p, INT INT INT INT or or or or EXT EXT EXT EXT Ref Ref Ref Ref DYNAMIC CHARACTERISTICS Differential Linearity Error (largest code error) f = 1MHz f = 10MHz No Missing Codes Integral Linearity Error, f = 1MHz Spurious-Free Dynamic Range(1) f = 1MHz (-1dBFS input) f = 10MHz (-1dBFS input) f = 20MHz (-1dBFS input) 2-Tone Intermodulation Distortion(3) f = 12MHz and 13MHz (-7dBFS each tone) Signal-to-Noise Ratio (SNR) f = 1MHz (-1dBFS input) f = 10MHz (-1dBFS input) f = 20MHz (-1dBFS input) f = 1MHz (-1dBFS input) f = 10MHz (-1dBFS input) Bits -40 +85 C 2 1.5 1.75 1 3 3.5 3.25 4 V V V V A MHz M || pF 50M Samples/s Clock Cycles 1.0 1.0 LSB LSB 5.0 LSBs 1 270 1.25 || 3 CONVERSION CHARACTERISTICS Sample Rate Data Latency 10k 6 0.6 0.6 Tested Tested 3.5 fS = 40MHz fS = 50MHz,TA = +25C fS = 40MHz, Full Temp TA = +25C 60 60 3Vp-p 3Vp-p UNITS 72 70 70 dBFS(2) dBFS dBFS -71.8 dBc 66 65 65 68 68 dBFS dBFS dBFS dBFS dBFS ADS2807 2 www.ti.com SBAS169B ELECTRICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MHz, unless otherwise noted. ADS2807Y PARAMETER DYNAMIC CHARACTERISTICS (Cont.) Signal-to-(Noise + Distortion) (SINAD)(4) f = 1MHz (-1dBFS input) f = 10MHz (-1dBFS input) f = 20MHz (-1dBFS input) f = 1MHz (-1dBFS input) f = 10MHz (-1dBFS Input) Channel-to-Channel Crosstalk Output Noise Aperture Delay Time Aperture Jitter Overvoltage Recovery Time DIGITAL INPUTS Logic Family Convert Command High Level Input Current(5) (VIN = 5V) Low Level Input Current (VIN = 0V) High Level Input Voltage Low Level Input Voltage Input Capacitance DIGITAL OUTPUTS Logic Family Logic Coding Low Output Voltage (IOL = 50A) Low Output Voltage, (IOL = 1.6mA) High Output Voltage, (IOH = 50A) High Output Voltage, (IOH = 0.5mA) Low Output Voltage, (IOL = 50A) High Output Voltage, (IOH = 50A) 3-State Enable Time 3-State Disable Time Output Capacitance ACCURACY (Internal Reference, 2Vp-p, Unless Otherwise Noted) Zero Error (Midscale) Zero Error Drift (Midscale) Gain Error(6) Gain Error Drift(6) Gain Error(7) Gain Error Drift(7) Power-Supply Rejection of Gain REFT Tolerance 2V Full-Scale 3V Full-Scale REFB Tolerance 2V Full-Scale 3V Full-Scale External REFT Voltage Range External REFB Voltage Range Reference Input Resistance POWER-SUPPLY REQUIREMENTS Supply Voltage: +VS Supply Current: +IS Power Dissipation: VDRV = 5V VDRV = 3V VDRV = 5V VDRV = 3V Thermal Resistance, JA TQFP-64 CONDITIONS MIN TYP MAX 65 64 64 68 68 85 0.2 2 1.2 2 57 3Vp-p 3Vp-p 2Vp-p Input Grounded UNITS dBFS dBFS dBFS dBFS dBFS dBFS LSBs rms ns ps rms ns +3V/+5V CMOS Compatible Rising Edge of Convert Clock Start Conversion +50 +10 +2.4 +1.0 5 A A V V pF CMOS Straight Offset Binary VDRV = 5V VDRV = 5V VDRV = 5V VDRV = 5V VDRV = 3V VDRV = 3V OE = L(5) OE = H(5) +0.1 +0.2 +4.9 +4.8 +0.4 +2.4 20 2 5 40 10 V V V V V V ns ns pF VS = 5% 1.0 16 1.5 66 1.0 23 70 Deviation From Ideal 3.0V Deviation From Ideal 3.25V 10 20 65 mV mV Deviation From Ideal 2.0V Deviation From Ideal 1.75V 10 20 3 2 375 65 mV mV V V at 25C at 25C at 25C REFB + 0.4 1.70 Operating Operating External Reference External Reference Internal Reference Internal Reference +4.75 +5.0 134 720 700 740 720 21.5 %FS ppm/C %FS ppm/C %FS ppm/C dB VS - 1.70 REFT - 0.4 +5.25 760 V mA mW mW mW mW C/W NOTES: (1) Spurious-Free Dynamic Range refers to the magnitude of the largest harmonic. (2) dBFS means dB relative to Full-Scale. (3) 2-tone intermodulation distortion is referred to the largest fundamental tone. This number will be 6dB higher if it is referred to the magnitude of the 2-tone fundamental envelope. (4) Effective number of bits (ENOB) is defined by as (SINAD - 1.76)/6.02. (5) A 50k pull-down resistor is inserted internally on OE pins. (6) Includes internal reference. (7) Excludes internal reference. ADS2807 SBAS169B 3 www.ti.com TIMING DIAGRAM N+2 N+1 Analog In N+4 N+3 N tD N+5 tL tCONV N+6 N+7 tH Clock 6 Clock Cycles t2 Data Out N-6 N-5 N-4 N-3 N-2 N-1 N Data Invalid N+1 t1 t3 Data Valid t4 SYMBOL DESCRIPTION MIN tCONV tL tH tD t1(1) t2(1) t3 t4 Convert Clock Period Clock Pulse LOW Clock Pulse HIGH Aperture Delay Data Hold Time, CL = 0pF New Data Delay Time, CL = 15pF max Data Valid Falling Edge Delay, CL = 15pF max Data Valid Rising Edge Delay, CL = 15pF max 20 9.0 9.0 TYP MAX UNITS 100s ns ns ns ns ns ns ns ns tCONV/2 tCONV/2 2 2.7 8.2 7.5 5.6 12 NOTE: (1) t1 and t2 times are valid for VDRV voltages of +2.7V to +5V. 61 60 59 58 57 54 53 52 51 50 GND INA INA TQFP CMA 55 REFTA 56 REFBA +VS GND REFBB CMB INB 62 GND 63 INT/EXT 64 INB GND Top View REFTB PIN CONFIGURATION 49 GND 1 48 GND GND 2 47 GND +VS 3 46 +VS GND 4 45 SEL +VS 5 44 GND OEB 6 43 +VS GND 7 42 OEA VDRVB 8 OVRB 9 41 GND ADS2807Y 40 VDRVA B12 (LSB) 10 39 OVRA 24 25 26 27 28 29 30 31 32 A8 A7 23 A9 22 A10 21 A11 20 A12 (LSB) 19 DVA 18 GND 17 CLK 33 A6 GND 34 A5 B6 16 DVB B7 15 B1(MSB) 35 A4 B2 36 A3 B8 14 B3 37 A2 B9 13 B4 38 A1 (MSB) B10 12 B5 B11 11 ADS2807 4 www.ti.com SBAS169B PIN DESCRIPTIONS PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 I/O DESIGNATOR I O O O O O O O O O O O O O O I O O O O O O O O GND GND +VS GND +VS OEB GND VDRVB OVRB B12 (LSB) B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 (MSB) DVB GND CLK GND DVA A12 (LSB) A11 A10 A9 A8 A7 A6 DESCRIPTION PIN Ground Ground +5V Supply Ground +5V Supply Output Enable, Channel B GND Logic Driver Supply Voltage, Channel B Over-Range Indicator, Channel B Data Bit 12 (D0), Channel B Data Bit 11 (D1), Channel B Data Bit 10 (D2), Channel B Data Bit 9 (D3), Channel B Data Bit 8 (D4), Channel B Data Bit 7 (D5), Channel B Data Bit 6 (D6), Channel B Data Bit 5 (D7), Channel B Data Bit 4 (D8), Channel B Data Bit 3 (D9), Channel B Data Bit 2 (D10), Channel B Data Bit 1 (D11), Channel B Data Valid, Channel B Ground Clock Ground Data Valid, Channel A Data Bit 12 (D0), Channel A Data Bit 11 (D1), Channel A Data Bit 10 (D2), Channel A Data Bit 9 (D3), Channel A Data Bit 8 (D4), Channel A Data Bit 7 (D5), Channel A Data Bit 6 (D6), Channel A 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 ADS2807 SBAS169B I/O DESIGNATOR O O O O O O A5 A4 A3 A2 A1 (MSB) OVRA VDRVA GND OEA +VS GND SEL +VS GND GND GND INA INA CMA REFTA REFBA GND INT/EXT I I I I O I/O I/O I I/O I/O O I I +VS GND REFBB REFTB CMB INB INB GND DESCRIPTION Data Bit 5 (D7), Channel A Data Bit 4 (D8), Channel A Data Bit 3 (D9), Channel A Data Bit 2 (D10), Channel A Data Bit 1 (D11), Channel A Over-Range Indicator, Channel A Logic Driver Supply Voltage, Channel A Ground Output Enable, Channel A +5V Supply Ground Input Range Select: HIGH = 3V, LOW = 2V +5V Supply Ground Ground Ground Analog Input, Channel A Complementary Analog Input, Channel A Common-Mode, Channel A Top Reference/Bypass, Channel A Bottom Reference/Bypass, Channel A Ground Reference Select: HIGH = External, LOW = Internal 50k Pull-Up Resistor +5V Supply Ground Bottom Reference/Bypass, Channel B Top Reference/Bypass, Channel B Common-Mode, Channel B Complementary Analog Input, Channel B Analog Input, Channel B Ground 5 www.ti.com TYPICAL CHARACTERISTICS At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MSPS, unless otherwise noted. SPECTRAL PERFORMANCE (Differential, 2Vp-p) SPECTRAL PERFORMANCE (Differential, 2Vp-p) 0 0 fIN = 1MHz SFDR = 72.7dBFS SNR = 65.1dBFS Amplitude (dBFS) Amplitude (dBFS) -20 -40 -60 -80 -40 -60 -80 -100 -100 -120 -120 0 5 10 15 20 0 25 5 15 20 Frequency (MHz) SPECTRAL PERFORMANCE (Differential, 3Vp-p) SPECTRAL PERFORMANCE (Differential, 3Vp-p) 25 0 fIN = 1MHz SFDR = 71.8dBFS SNR = 67.2dBFS fIN = 10MHz SFDR = 68.4dBFS SNR = 66.4dBFS -20 Amplitude (dBFS) -20 -40 -60 -80 -100 -40 -60 -80 -100 -120 -120 0 5 10 15 20 25 0 5 Frequency (MHz) 10 15 20 25 Frequency (MHz) DYNAMIC PERFORMANCE vs CLOCK 2-TONE INTERMODULATION DISTORTION 80 0 REF = 2V fIN = 3.5MHz f1 = 12MHz f2 = 13MHz IMD(3) = -71.8dBc 75 SNR, SFDR (dBFS) -20 Amplitude (dBFS) 10 Frequency (MHz) 0 Amplitude (dBFS) fIN = 10MHz SFDR = 69.8dBFS SNR = 64.9dBFS -20 -40 -60 -80 SFDR 70 65 SNR 60 -100 55 -120 0 5 10 15 20 25 35 40 45 50 55 60 Clock (MHz) Frequency (MHz) ADS2807 6 www.ti.com SBAS169B TYPICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MSPS, unless otherwise noted. DYNAMIC PERFORMANCE vs CLOCK DYNAMIC PERFORMANCE vs INPUT FREQUENCY 80 85 REF = 3V fIN = 3.5MHz Dynamic Performance (dBFS) 80 SNR, SFDR (dBFS) 75 SFDR 70 SNR 65 60 55 SFDR 75 70 THD 65 SNR 60 55 SINAD 50 45 Power = -1dBFS 40 35 40 45 50 55 60 1 10 Clock (MHz) SWEPT POWER (SFDR) DYNAMIC PERFORMANCE vs INPUT FREQUENCY 85 100 fIN = 10MHz dBFS 90 80 80 SFDR 75 SFDR (dBFS, dBc) Dynamic Performance (dBFS) 100 Frequency (MHz) 70 THD 65 60 SNR SINAD 60 50 dBc 40 30 20 55 10 Power = -6dBFS 50 1 70 10 0 100 -60 -50 -40 -30 -20 -10 Frequency (MHz) Input Amplitude (dBFS) DIFFERENTIAL LINEARITY ERROR (Differential, 2Vp-p) INTEGRAL LINEARITY ERROR (Differential, 2Vp-p) 0 6 2 fIN = 10MHz fIN = 10MHz 1.5 4 2 0.5 ILE (LSB) DLE (LSB) 1 0 -0.5 0 -2 -1 -4 -1.5 -6 -2 0 1024 2048 3072 4096 ADS2807 SBAS169B 0 1024 2048 3072 4096 Code Code 7 www.ti.com TYPICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MSPS, unless otherwise noted. INTEGRAL LINEARITY ERROR (Differential, 3Vp-p) DIFFERENTIAL LINEARITY ERROR (Differential, 3Vp-p) 5 0.75 fIN = 10MHz 0.50 3 2 ILE (LSB) 0.25 DLE (LSB) fIN = 10MHz 4 0 -0.25 1 0 -1 -2 -3 -0.50 -4 -5 -0.75 0 1024 2048 3072 0 4096 1024 2048 3072 CROSSTALK (Channel A) OUTPUT NOISE HISTOGRAM (DC Input) 500k 0 3V Full Scale fIN = 4.8MHz -25 Amplitude (dBFS) 400k Counts 4096 Output Codes Code 300k 200k -50 -75 -100 100k -110 N-2 N-1 N N+1 0 N+2 2.5 5 7.5 DYNAMIC PERFORMANCE vs TEMPERATURE 12.5 15 17.5 20 22.5 25 CROSSTALK (Channel B) 75 0 fIN = 10MHz fIN = 3.5MHz 70 -25 Amplitude (dBFS) SFDR SNR, SFDR (dBFS) 10 Frequency (MHz) Code 65 SNR 60 -50 -75 55 -100 50 -110 -60 -40 -20 0 20 40 60 80 100 0 Temperature (C) 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 Frequency (MHz) ADS2807 8 www.ti.com SBAS169B APPLICATION INFORMATION * Even-order harmonics are minimized. THEORY OF OPERATION * Improves the noise immunity based on the converter's common-mode input rejection. The ADS2807 integrates two high-speed CMOS ADCs and an internal reference. The ADCs utilize a pipelined converter architecture consisting of eleven internal stages. Each stage feeds its data into the digital error correction logic, ensuring excellent differential linearity and no missing codes at the 12-bit level. The output data becomes valid after the rising clock edge (see Timing Diagram). The pipeline architecture results in a data latency of 6 clock cycles. The analog input of the ADS2807 consists of a differential track-and-hold circuit. The differential topology along with tightly matched poly-poly capacitors produce a high level of AC performance at high sampling rates and in some undersampling applications. Both inputs (IN, IN) require external biasing using a common-mode voltage that is typically at the mid-supply level (+VS/2). DRIVING THE ANALOG INPUTS The analog inputs of the ADS2807 are very high impedance and should be driven through an R-C network designed to pass the highest frequency of interest. This prevents highfrequency noise in the input from affecting SFDR and SNR. The ADS2807 can be used in a wide variety of applications and deciding on the best performing analog interface circuit depends on the type of application. The circuit definition should include considerations of input frequency spectrum and amplitude, single-ended or differential drive, and available power supplies. For example, communication (frequency domain) applications process frequency bands not including DC. In imaging (time domain) applications, the input DC component must be maintained into the ADC. Features of the ADS2807 include full-scale select (SEL), external reference, and CM output, providing flexibility to accommodate a wide range of applications. The ADS2807 should be configured to meet application objectives, while observing the headroom requirements of the driving amplifiers, to yield the best overall performance. The ADS2807 input structure allows it to be driven either single-ended or differentially. Differential operation of the ADS2807 requires an in-phase input signal and a 180 outof-phase part simultaneously applied to the inputs (IN, IN). The differential operation offers a number of advantages that, in most applications, will be instrumental in achieving the best dynamic performance of the ADS2807: * The signal swing is half of that required for the singleended operation and, therefore, is less demanding to achieve while maintaining good linearity performance from the signal source. * The reduced signal swing allows for more headroom in the interface circuitry and, therefore, a wider selection of the best suitable driver op amp. Using the single-ended mode, the signal is applied to one of the inputs, while the other input is biased with a DC voltage to the required common-mode level. Both inputs are equal in terms of their impedance and performance, except that applying the signal to the complementary input (IN) instead of the IN input will invert the input signal relative to the output code. For example, in the case when the input driver operates in inverting mode, using IN as the signal input will restore the phase of the signal to its original orientation. Time-domain applications may benefit from a single-ended interface configuration and its reduced circuit complexity. Driving the ADS2807 with a single-ended signal will result in a reduction of the distortion performance, while maintaining good signal-to-noise ratio (SNR). Employing dual-supply amplifiers and AC-coupling will usually yield the best results, while DC-coupling and/or single-supply amplifiers impose additional design constraints due to their headroom requirements, especially when selecting the 3Vp-p input range. However, single-supply amplifiers have the advantage of inherently limiting their output swing to within the supply rails. Alternatively, a voltage limiting amplifier, like the OPA688, may be considered to set fixed-signal limits and avoid any severe overrange condition for the ADC. The full-scale input range of the ADS2807 is defined by the reference voltages. For example, setting the range select pin to SEL = LOW, and using the internal references (REFT = +3.0V and REFTB = +2.0V), the full-scale range is defined as: FSR = 2 * (REFT - REFB) = 2Vp-p. The trade-off of the differential input configuration versus the single-ended is its higher complexity. In either case, the selection of the driver amplifier should be such that the amplifier's performance will not degrade the ADC's performance. The ADS2807 operates on a single power supply that requires a level shift for ground-based bipolar input signals to comply with its input voltage range requirements. The input of the ADS2807 is of a capacitive nature and the driving source needs to provide the current to charge or discharge the input sampling capacitor while the track-andhold is in track mode. This effectively results in a dynamic input impedance that depends on the sampling frequency. In most applications, it is recommended to add a series resistor, typically 20 to 50, between the drive source and the converter inputs. This will isolate the capacitive input from the source, which can be crucial to avoid gain peaking when using wideband operational amplifiers. Secondly, it will create a first-order, low-pass filter in conjunction with the specified input capacitance of the ADS2807. Its cutoff frequency can be adjusted even further by adding an external shunt capacitor from each signal input to ground. The optimum values of this R-C network depend on a variety of factors that include the ADS2807 sampling rate, the selected op amp, the interface configuration and the particular application (time domain versus frequency domain). Generally, ADS2807 SBAS169B 9 www.ti.com increasing the size of the series resistor and/or capacitor will improve the SNR performance, but depending on the signal source, large resistor values may be detrimental to achieving good harmonic distortion. In any case, optimizing the R-C values for the specific application is encouraged. Transformer Coupled, Single-Ended to Differential Configuration If the application requires a signal conversion from a singleended source to drive the ADS2807 differentially, an RF transformer might be a good solution. The selected transformer must have a center tap in order to apply the commonmode DC voltage necessary to bias the converter inputs. AC grounding the center tap will generate the differential signal swing across the secondary winding. Consider a step-up transformer to take advantage of a signal amplification without the introduction of another noise source. Furthermore, the reduced signal swing from the source may lead to improved distortion performance. The differential input configuration provides the noticeable advantage of achieving high SFDR over a wide range of input frequencies. In this mode, both inputs of the ADS2807 see matched impedances. Figure 1 shows the schematic for the suggested transformer coupled interface circuit. The component values of the R-C low-pass may be optimized depending on the desired roll-off frequency. The resistor across the secondary side (RT) should be calculated using the equation RT = n2 * RG to match the source impedance (RG) for good power transfer and VSWR. The circuit example of Figure 1 shows voltage feedback amplifier OPA680 driving the RF transformer, which converts the single-ended signal into a differential. The OPA680 can be employed for either single- or dual-supply operation. For details on how to optimize its frequency response, refer to the OPA680 data sheet. With the 49.9 series output resistor, the amplifier emulates a 50 source (RG). Any DC content of the signal can be easily blocked by a capacitor (0.1F) to avoid DC loading of the op amp's output stage. AC-Coupled, Single-Ended to Differential Interface with Dual-Supply Op Amps Some applications demand a very high dynamic range and low levels of intermodulation distortion, but usually allow the input signal to be AC-coupled into the ADC. Appropriate driver amplifiers need to be selected to maintain the excellent distortion performance of the ADS2807. Often, these op amps deliver the lowest distortion with a small, groundcentered signal swing that requires dual power supplies. Because of the AC-coupling, this requirement can be easily accomplished, and the needed level shifting of the input signal can be implemented without affecting the driver circuit. RG VIN 49.9 0.1F 1:n 24.9 IN OPA680 47pF R1 1/2 ADS2807Y RT 24.9 R2 IN CM +2.5V 47pF + One Channel of Two 10F 0.1F FIGURE 1. Converting a Single-Ended Input Signal into a Differential Signal Using an RF-Transformer. ADS2807 10 www.ti.com SBAS169B to the ADS2807. With a minimum gain stability of +3, the gain resistors have to be modified, as well as optimizing the series resistor and shunt capacitance at each of the converter inputs. Figure 2 shows an example of such an interface circuit specifically designed to maximize the dynamic performance. The voltage feedback amplifier, OPA642, maintains an excellent distortion performance for input frequencies of up to 15MHz. The two amplifiers (A1, A2) are configured as an inverting and noninverting gain stage to convert the input signal from single-ended to differential. The nominal gain for this stage is set to +2V/V. The outputs of the OPA642s are AC-coupled to the converter's differential inputs. This will keep the distortion performance at its best since the signal range stays within the linear region of the op amp and sufficient headroom to the supply rails can be maintained. Four resistors located between the top (REFT) and bottom (REFB) reference shift the input signal to a common-mode voltage of approximately +2.5V. AC-Coupled, Single-Ended-to-Differential Interface for Single-Supply Operation The previously discussed interface circuit can be modified if the system only allows for a single-supply operation, e.g., VS = +5V. Single-supply operation requires the driver amplifier to be biased as well in order to process a bipolar input signal. Typically, single-supply amplifiers do not achieve distortion performance as well as dual-supply op amps. The driver amplifier's output swing must exceed the full-scale input range of the converter. In addition, dual op amps, such as the current-feedback OPA2681, should be considered since they provide the closest open-loop gain and phase matching between the two channels. Shown in Figure 3 is a single-supply interface circuit for an AC-coupled input signal. With the ADS2807 set to the 2Vp-p input range, the top and bottom references (REFT, REFB) provide an output voltage The interface circuit of Figure 2 can be modified to extend the bandwidth to approximately 25MHz, by replacing the OPA642 with its decompensated version, the OPA643. The OPA643 provides the necessary slew rate for a low distortion front end 402 200 VIN 0.1F 16.5 A1 OPA642 1.82k 1.82k REFT IN 100pF 402 1/2 ADS2807Y 402 0.1F 16.5 A2 OPA642 IN 100pF 1.82k REFB 1.82k One Channel of Two FIGURE 2. AC-Coupled Differential Driver Interface with OPA642. RF 499 0.1F VIN RIN 249 1/2 OPA2681 RS 24.9 IN RP 499 499 68pF VCM = +2.5V 1/2 ADS2807Y CM 0.1F +5V RS 24.9 1/2 OPA2681 IN 68pF RF 499 RG 249 RP 499 One Channel of Two 0.1F FIGURE 3. AC-Coupled, Differential Interface for Single-Supply Operation. ADS2807 SBAS169B 11 www.ti.com of +3.0V and +2.0V, respectively. The CM output of the ADS2807 is used to bias the inputs of the driving amplifiers. Using the OPA2681 on a single +5V supply, its ideal common-mode point is +2.5V, which coincides with the recommended common-mode input level for the ADS2807, thus eliminating the need for coupling capacitors between the amplifiers and the converter. The addition of a small series resistor (RS) between the output of the op amps and the input of the ADS2807 will be beneficial in almost all interface configurations. It will decouple the op amp's output from the capacitive load and avoid gain peaking that can result in increased noise. For best spurious and distortion performance, the resistor value should be kept below 100. Furthermore, the series resistor, in combination with the shunt capacitor, establishes a passive low-pass filter limiting the bandwidth for the wideband noise, thus improving the SNR. The spurious free dynamic range of this single-supply front end is limited by the second harmonic distortion. An improvement of several dB may be realized by adding a pull-down resistor (RP) at the output of each amplifier. This pulls a DC bias current out of the output stage of the amplifier. It is set to approximately 5mA, see Figure 3, but will vary depending on the amplifier used. Single-Ended, AC-Coupled, Dual-Supply Interface The circuit provided in Figure 4 shows typical connections for using the ADS2807 in a single-ended input configuration. The bias requirements for AC-coupling are provided by a single resistor to the CM output lead. The single-ended mode of operation should be considered for ease of interface complexity and applications where the dynamic performance can be compromised. The series resistor RS, along with the shunt capacitance, provide the means to adjust the bandwidth and optimize the performance towards good signal-tonoise ratio. In addition, the amplifier configuration can be easily modified for an anti-aliasing filter based on a secondorder Sallen-Key or Multiple-Feedback topology. The interface example, shown in Figure 4, operates with the full-scale range of the ADS2807 set to 2Vp-p, leaving sufficient headroom for the output of the OPA642 to drive the converter and maintain low signal distortion. +5V RS 16.5 VIN 0.1F IN OPA642 68pF 1/2 ADS2807Y -5V RF 402 1.82k CM IN 0.1F RG 402 One Channel of Two FIGURE 4. AC-Coupling the Dual-Supply Amplifier OPA642 to the ADS2807 for a 2Vp-p Full-Scale Input Range. ADS2807 12 www.ti.com SBAS169B DC-Coupled, Differential Driver with Level Shift Several applications will require that the bandwidth of the signal path include DC, in which case, the signal has to be DC-coupled to the ADC. An op amp based interface circuit can be configured to scale and level shift the input signal to be compatible with the selected input range of the ADC. The circuit shown in Figure 5 employs a dual op amp, OPA2681, to drive the input of the ADS2807 differentially. The singlesupply, general-purpose op amp OPA234 is added to buffer the common-mode voltage of +2.5V, available at the CM pin, and apply it to the input of the driver amplifier. This sets the correct DC voltage to bias the inputs of the ADS2807. It should be noted that any DC voltage differences between the IN and IN inputs of the ADS2807 will result in an offset error. Using the OPA2681, this circuit can be operated either with a single or a dual 5V supply. down resistor at the range select pin (SEL). Therefore, this pin can be either hardwired to ground or left unconnected, which will default the converter to a 2Vp-p full-scale input range (FSR). While set for the 2Vp-p range, the top and bottom reference voltages will be REFT = +3.0V and REFB = +2.0V. Switching to the 3Vp-p range changes those voltages to REFT = +3.25V and REFB = +1.75V. The reference buffers can be utilized to supply up to 1mA/channel (2mA total, sink and source) to external circuitry. To ensure proper operation with any reference configuration, it is necessary to provide solid bypassing at all reference pins in order to keep the clock feedthrough to a minimum, as shown in Figure 6. Good performance requires using 0.1F low inductance capacitors. All bypassing capacitors should be located as close to their respective pins as possible. REFERENCE OPERATION The internal reference consists of a bandgap voltage reference, the drivers for the top and bottom reference, and the resistive reference ladder. References are internally connected, e.g.: REFTA is connected to REFTB, and REFBA is connected to REFBB. The bandgap reference circuit includes logic functions that allow setting the analog input swing of the ADS2807 to a differential full-scale range of either 2Vp-p or 3Vp-p by simply tying the SEL pin to a LOW or HIGH potential, respectively. While operating the ADS2807 in the external reference mode, the buffer amplifiers for REFT and REFB are disabled. The ADS2807 has an internal 50k pull- 1/2 ADS2807 REFT + 10F CM 0.1F + 10F REFB 0.1F + 10F 0.1F FIGURE 6. Recommended Bypassing for the Reference Pins. 499 249 VIN 1/2 OPA2681 24.9 IN 22pF 499 249 1/2 ADS2807Y 499 IN 249 24.9 CM 1/2 OPA2681 22pF 499 24.9 OPA234 249 0.1F 0.1F 0.1F 1k One Channel of Two FIGURE 5. DC-Coupled Input Driver with Level Shifting. ADS2807 SBAS169B 13 www.ti.com USING EXTERNAL REFERENCES For even more design flexibility, the internal reference can be disabled and an external reference voltage used. Driving both channels with an external reference offers the best performance, as it allows the channels to maintain balance. The utilization of an external reference may be considered for applications requiring higher accuracy, improved temperature performance, or a wide adjustment range of the converter's full-scale range. In multichannel applications, the use of a common external reference has the benefit of obtaining better matching and drift of the full-scale range between converters. Figure 7 gives an example of an external reference circuit using a single-supply, low-power, dual op amp (OPA2234). The external references can vary as long as the value of the external top reference (REFT) stays within the range of VS - 1.70V and REFB + 0.4V, and the external bottom reference (REFB) stays within 1.70V and REFT - 0.4V. Note that the function of the range selector pin (SEL) is disabled while the converter operates in external reference mode. Setting the ADS2807 for external reference mode requires the INT/EXT pin (pin 18) to be HIGH. The logic level applied to the INT/EXT pin of the ADS2807 determines if the converter operates with either the built-in reference or external reference voltages. Due to this function pin having an internal 50k pull-up resistor, the default configuration is external reference mode. Grounding this pin will activate the internal reference option. IN (see Figure 3) results in 2Vp-p on the output of the trackand-hold. Likewise, 2Vp-p on the IN and 0Vp-p on the IN (see Figure 4) results in 2Vp-p on the output of the track-and-hold. Therefore, the reference voltages, REFT and REFB, are the same for both differential and single-ended inputs, as shown in Table I. INPUT REFERENCE IN (Pins-50, 63) IN (Pins-51, 62) REFT REFB 2Vp-p Differential 1Vp-p Times 2 Inputs Internal or External 2V to 3V 3V to 2V +3V +2V 2Vp-p Single-Ended 2Vp-p Times 1 Input Internal or External 1.5V to 3.5V 2.5VDC +3V +2V 3Vp-p Differential 1.5Vp-p Times 2 Inputs Internal or External 3Vp-p Single-Ended 3Vp-p Times 1 Input Internal or External 1.75V to 3.35V 3.25V to 1.75V +3.25V +1.75V 1V to 4V 2.5VDC +3.25V +1.75V TABLE I. Reference Voltages for Input Signal Ranges. The external references may be changed for different tasks. The ADS2807 will follow the external references with a latency of 8 to 10 clock cycles. If it is desired to use INT/EXT and SEL to change the configuration of a circuit for different tasks, a large amount of time must be allowed. This time could be hundreds of microseconds. Refer to the Diagram on the front page. Note that there is no disconnect for external references. If it is desired to switch between internal and external references, disconnect switches must be added between the external references and the ADS2807. The input track and hold amplifier is differential. A positive 1Vp-p on the IN and its compliment, a negative 1Vp-p, on the +5V +5V OPA2234 A1 4.7k < 3.30V Top Reference R3 R4 R1 REF1004 +2.5V + 10F R2 0.1F OPA2234 A2 > 1.70V Bottom Reference One Channel of Two FIGURE 7. Example for an External Reference Driver Using the Dual, Single-Supply Op Amp, OPA2234. ADS2807 14 www.ti.com SBAS169B DIGITAL INPUTS AND OUTPUTS Clock Input Requirements Data Outputs Both channels of the ADS2807 are controlled by the same clock on the rising edge. Utilizing a single clock reduces timing uncertainty in the sampling of the two channels. Clock jitter is critical to the SNR performance of high-speed, highresolution ADCs. Clock jitter leads to aperture jitter (tA), which adds noise to the signal being converted. The ADS2807 samples the input signal on the rising edge of the CLK input. Therefore, this edge should have the lowest possible jitter. The jitter noise contribution to total SNR is given by the following equation. If this value is near your system requirements, input clock jitter must be reduced. Jitter SNR = 20 log 1 rms signal to rms noise 2 IN t A where: IN is input signal frequency tA is rms clock jitter Particularly in undersampling applications, special consideration should be given to clock jitter. The clock input should be treated as an analog input in order to achieve the highest level of performance. Any overshoot or undershoot of the clock signal may cause degradation of the performance. When digitizing at high sampling rates, the clock should have 50% duty cycle (tH = tL), along with fast rise and fall times of 2ns or less. The clock input of the ADS2807 can be driven with either 3V or 5V logic levels. Using low-voltage logic (3V) may lead to improved AC performance of the converter. Over Range Indicator (OVR) If the analog input voltage exceeds the set full-scale range, an over range condition exists. The "OVR" pin of the ADS2807 can be used to monitor any such out-of-range condition. This "OVR" output is updated along with the data output corresponding to the particular sampled analog input voltage. Therefore, the OVR data is subject to the same pipeline delay as the digital data. The OVR output is LOW when the input voltage is within the defined input range. It will go to HIGH if the applied signal exceeds the full-scale range. The digital outputs of the ADS2807 can be set to a highimpedance state by driving OE (pins 6 and 42) with a logic HIGH. Normal operation is achieved with pins 6 and 42 LOW due to internal pull-down resistors. This function is provided for testability purposes and is not meant to drive digital buses directly, or be dynamically changed during the conversion process. The output data format of the ADS2807 is in positive Straight Offset Binary code, as shown in Tables II and III. This format can easily be converted into the Binary Two's Complement code by inverting the MSB. SINGLE-ENDED INPUT (IN = CM, Pins 52, 61) +FS-1LSB (IN = CMV + FSR/2) 1111 1111 1111 +1/2 FS 1100 0000 0000 Bipolar Zero (IN = VCM) 1000 0000 0000 -1/2 FS 0100 0000 0000 -FS (IN = CMV - FSR/2) 0000 0000 0000 TABLE II. Coding Table for Single-Ended Input Configuration with IN Tied to the Common-Mode Voltage. DIFFERENTIAL INPUT STRAIGHT OFFSET BINARY (SOB) +FS-1LSB (IN = +3V, IN = +2V) 1111 1111 1111 +1/2 FS 1100 0000 0000 Bipolar Zero (IN = IN = VCM) 1000 0000 0000 -1/2 FS 0100 0000 0000 -FS (IN = +2V, IN = +3V) 0000 0000 0000 TABLE III. Coding Table for Differential Input Configuration. Data output is in the form of two parallel words. It is recommended that the capacitive loading on the data lines be as low as possible (< 15pF). Higher capacitive loading will cause larger dynamic currents as the digital outputs are changing. Those high current surges can feed back to the analog portion of the ADS2807 and affect the performance. If necessary, external buffers or latches close to the converter's output pins may be used to minimize the capacitive loading. They also provide the added benefit of isolating the ADS2807 from high-frequency digital noise on the bus coupling back into the converter. ADS2807 SBAS169B STRAIGHT OFFSET BINARY (SOB) 15 www.ti.com Digital Output Driver Supply (VDRV) high-frequency designs. Multilayer PC boards are recommended for best performance since they offer distinct advantages, such as minimizing ground impedance, separation of signal layers by ground layers, etc. The ADS2807 should be treated as an analog component. Whenever possible, the supply pins should be powered by the analog supply. This will ensure the most consistent results, since digital supply lines often carry high levels of noise that otherwise would be coupled into the converter and degrade the achievable performance. The ground pins should directly connect to an analog ground plane that covers the PC board area under the converter. While designing the layout it is important to keep the analog signal traces separated from any digital lines to prevent noise coupling onto the analog signal path. Due to its high sampling rate, the ADS2807 generates high-frequency current transients and noise (clock feedthrough) that are fed back into the supply and reference lines. This requires that all supply and reference pins are sufficiently bypassed. Figure 8 shows the recommended decoupling scheme for the ADS2807. In most cases, 0.1F ceramic chip capacitors at each pin are adequate to keep the impedance low over a wide frequency range. Their effectiveness largely depends on the proximity to the individual supply pin. Therefore, they should be located as close to the supply pins as possible. If system supplies are not a low enough impedance, adding a small tantalum capacitor will yield the best results. Each channel of the ADS2807 has a separate dedicated supply pin (8, 40) for the output logic drivers, VDRV, which are not internally connected to the other supply pins. Setting the voltage at VDRV to +5V or +3V, the ADS2807 produces corresponding logic levels and can directly interface to the selected logic family. The output stages are designed to supply sufficient current to drive a variety of logic families. However, it is recommended to use the ADS2807 with +3V logic supply. This will lower the power dissipation in the output stages due to the lower output swing and reduce current glitches on the supply line that may affect the AC performance of the converter. In some applications, it might be advantageous to decouple the VDRV pin with additional capacitors or a pi-filter. OUTPUT ENABLE (OE ) The digital outputs of the ADS2807 can be set to high impedance (tri-state) by driving OE A and OE B (pins 6, 42) with a logic HIGH. Normal operation is achieved with the same pins pulled LOW. GROUNDING AND DECOUPLING Proper grounding, bypassing, short trace lengths, and the use of power and ground planes are particularly important for ADS2807 +VS GND 57 0.1F 55, 58 +VS +VS GND 3 (46) 1, 2, 64 (47, 48, 49) GND 5 (43) 0.1F 0.1F +5V 4 (44) GND VDRV 7 (41) 8 (40) GND 23, 25 0.1F +3V/+5V Numbers in Parenthesis Indicate Pins for Channel A FIGURE 8. Recommended Bypassing for the Supply Pins. ADS2807 16 www.ti.com SBAS169B PACKAGE OPTION ADDENDUM www.ti.com 21-May-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) ADS2807Y/1K5 ACTIVE HTQFP PAP 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ADS2807Y/1K5G4 ACTIVE HTQFP PAP 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ADS2807Y/250 ACTIVE HTQFP PAP 64 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ADS2807Y/250G4 ACTIVE HTQFP PAP 64 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant ADS2807Y/1K5 HTQFP PAP 64 1500 330.0 24.8 13.0 13.0 1.5 16.0 24.0 Q2 ADS2807Y/250 HTQFP PAP 64 250 330.0 24.4 13.0 13.0 1.4 16.0 24.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS2807Y/1K5 HTQFP PAP 64 1500 367.0 367.0 45.0 ADS2807Y/250 HTQFP PAP 64 250 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated