PL IA N T Features CO M Carbon element *R oH S Ganging up to 8 sections available Knurled and flatted shaft styles Audio taper option Tracking error within 3 dB RoHS compliant* PTD90 Series - 9 mm Multi-Ganged Potentiometer Environmental Characteristics Operating Temperature .................................-10 C to +50 C Rotational Life ................... 15,000 cycles IP Rating .......................................... IP 40 Mechanical Characteristics Mechanical Angle ...................300 10 Running Torque ...............10 to 250 g-cm Stop Strength .......................... 4.0 kg-cm Shaft Push/Pull Strength .......5.0 kgf min. Shaft Wobble .....0.6 x L/20 mm p-p max. Mounting Torque ............. 7.0 kg-cm min. Soldering Condition Manual Soldering ........96.5 Sn/3.0 Ag/0.5 Cu solid wire or no-clean rosin cored wire 270 C max. for 3 seconds Wave Soldering ............. 96.5 Sn/3.0 Ag/0.5 Cu solder with no-clean flux 260 C max. for 5 seconds Wash Process ...... Not recommended Mounting Hardware ........ One flat washer and one mounting nut supplied per potentiometer Product Dimensions PTD901 PTD902 9.65 0.5 (.380 .020) 7.05 0.5 (.278 .020) M7XP0.75 M7XP0.75 0.8 0.2 (.031 .008) R1 0.7 (.028) 0.3 (.012) R2 R1 0.3 (.012) 5.0 (.197) 2.5 (.098) 2 PLCS. 0.7 (.028) 0.8 0.2 (.031 .008) 5.0 (.197) 2 PLCS. RECOMMENDED PCB LAYOUT 5.0 (.197) DIA. HOLES 3 PLCS. 1.0 +0.2/-0 (.039 +.008/-0) 3 2 MOUNTING SURFACE 1 5.0 (.197) RECOMMENDED PCB LAYOUT DIA. HOLES 6 PLCS. 1.0 +0.2/-0 (.039 +.008/-0) R1 SCHEMATIC 3 2 2 1 1 R2 R1 3 DIMENSIONS: 5.0 (.197) 3 5.0 (.197) 2 R1 1 MM (INCHES) SCHEMATIC MOUNTING SURFACE 2.5 (.098) 2 R1 1 3 R2 1' 3' 2' Derating Curve Rating Power Ratio (%) Electrical Characteristics Standard Resistance Range ....................... 1 K ohms to 1 M ohms Total Resistance Tolerance .................................10 % or 20 % Standard Tapers ................Linear & audio Maximum Operating Voltage ............................... 150 VAC, 20 VDC Rated Power Linear Taper .......................0.05 watts Audio Taper ......................0.025 watts Noise .................................. 100 mV max. Insulation Resistance @ 250 VDC ....................................... 100 M ohms Dielectric Withstanding Voltage ..............................................300 VAC End Resistance .................20 ohms max. Tracking Error (-40 dB to 0 dB).......3 dB 100 80 60 40 33 20 0 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (C) Standard Resistance Table Resistance (Ohms) 1,000 2,000 5,000 10,000 20,000 50,000 100,000 200,000 500,000 1,000,000 Resistance Code 102 202 502 103 203 503 104 204 504 105 *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. Applications Audio/TV sets Automotive sound systems Amplifiers/mixers/drum machines/synthesizers/DJ equipment Multimedia sound systems Portable electronics PTD90 Series - 9 mm Multi-Ganged Potentiometer Product Dimensions PTD904 PTD906 PTD908 17.2 0.5 (.677 .020) 24.7 0.5 (.972 .020) M7XP0.75 M7XP0.75 R4 R3 R2 R1 2.5 (.098) 3 3 3 2 2 2 2 1 1 1 1 5.0 (.197) 2.5 (.098) DIA. HOLES 2.5 12 PLCS. (.098) 1.0 +0.2/-0 (.039 +.008/-0) 3 3 5.0 (.197) 2.5 (.098) 3 3 3 3 3 2 2 2 2 2 1 1 1 1 1 1 5.0 R6 R5 (.197) R4 R3 1 R3 2.5 (.098) DIA. HOLES 18 PLCS. 1.0 +0.2/-0 (.039 +.008/-0) 5.0 (.197) 3 3 3 3 3 2 2 2 2 3 3 5.0 (.197) 3 3 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 R6 R5 2.5 (.098) 2 5.0 (.197) 3 5.0 R8 R7 (.197) 2 1 R2 2.5 (.098) 5.0 (.197) 5.0 (.197) MOUNTING SURFACE R2 R1 2.5 (.098) 2.5 (.098) 2 1 R4 M7XP0.75 0.8 0.2 (.031 .008) 5.0 (.197) 5.0 (.197) RECOMMENDED PCB LAYOUT 5.0 (.197) 2 3 2 R2 R1 2.5 (.098) 2.5 (.098) 3 3 2 R4 R3 5.0 (.197) SCHEMATIC 2 R6 R5 5.0 (.197) 5.0 (.197) 5.0 (.197) SCHEMATIC 3 2.5 (.098) R8 R7 0.8 0.2 (.031 .008) RECOMMENDED PCB LAYOUT MOUNTING SURFACE R2 R1 2.5 (.098) R2 R1 5.0 (.197) 5.0 (.197) 3 R4 R3 R4 R3 2.5 (.098) RECOMMENDED PCB LAYOUT 5.0 (.197) 5.0 (.197) R6 R5 0.8 0.2 (.031 .008) 5.0 (.197) 2.5 (.098) 32.2 0.5 (1.268 .020) 3 R4 R3 2.5 (.098) 2.5 (.098) 3 3 MOUNTING SURFACE DIA. HOLES 24 PLCS. 1.0 +0.2/-0 2.5 (.039 +.008/-0) (.098) R2 R1 SCHEMATIC 3 3 3 3 3 3 3 3 1 R1 1 R6 1 R5 1 R4 DIMENSIONS: 1 R3 MM (INCHES) 1 R2 1 R1 2 2 2 1 1 R8 R7 2 2 1 1 R6 R5 2 2 1 1 R4 R3 2 1 1 R2 R1 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. PTD90 Series - 9 mm Multi-Ganged Potentiometer How To Order Product Dimensions SHAFT STYLE "K" L B PTD90 1 - 2 0 20 K - B 203 SHAFT STYLE "F" 0.5 (.020) 1.5 (.059) Model * PTD90 = No Switch 0.5 L (.020) B 18 TEETH KNURL A 4.5 (.177) 1.0 (.039) 6.0 +0/-0.1 (.236 +0/-.004) DIA. 30 9.5 0.3 (.374 .012) 6.0 (.236) No. of Sections * 1 = 1 Section * 2 = 2 Sections * 3 = 3 Sections * 4 = 4 Sections * 5 = 5 Sections * 6 = 6 Sections * 8 = 8 Sections F 9.5 0.3 (.374 .012) 4.8 0.3 (.189 .012) 6.0 +0/-0.1 (.236 +0/-.004) DIA. 60 Pin Style * 1 = PC Pins vertical/ down facing and 10 % Total Resistance Tolerance 4.8 0.3 (.189 .012) 4.5 (.177) *2= 6.5 0.3 (.256 .012) 6.5 0.3 (.256 .012) 6.0 (.236) 0.8 (.031) 5.0 (.197) Center Detent Option * 0 = No Detent * 2 = Center Detent 3.5 (.138) 2.0 (.079) 0.8 (.031) 3.5 (.138) 2.0 (.079) 0.8 (.031) 0.8 (.031) Standard Shaft Length * 15 = 15 mm * 20 = 20 mm * 25 = 25 mm 5.0 (.197) Shaft Styles * K = Knurled Type Shaft (Metal) 18 Toothed Serration Type * F = Flatted Metal Shaft SHAFT SHOWN IN CCW POSITION SHAFT SHOWN IN CCW POSITION PC Pins vertical/ down facing and 20 % Total Resistance Tolerance L 15 (.591) 20 (.787) 25 (.984) L 15 (.591) 20 (.787) 25 (.984) B 5 (.197) 7 (.276) 10 (.394) B 5 (.197) 7 (.276) 10 (.394) Resistance Taper (See Taper Charts) Taper Series followed by Curve Number A 6 (.236) 10 (.394) 12 (.472) F 7 (.276) 12 (.472) 12 (.472) Resistance Code (See Table) DIMENSIONS: Other shaft styles available. MM (INCHES) Tapers C Series Tapers B Series Tapers A Series Tapers 100 100 50 40 30 A6 A5 ): : 0A A) (3 (25 A4 A): (20 5A): A (1 A2 A): (10 A): A1 (05 20 10 0 10 20 30 40 50 60 Rotational Travel (%) 70 80 90 100 Terminal 1-2 Output Voltage X 100 (%) Terminal 1-3 Input Voltage 60 (5B ): B 5 4 (3B ): B 3 (2B ): B 2 (B ): (1B B ): B 80 70 90 80 ): B 90 80 (4B 90 Terminal 1-2 Output Voltage X 100 (%) Terminal 1-3 Input Voltage Terminal 1-2 Output Voltage X 100 (%) Terminal 1-3 Input Voltage 1 100 70 60 50 40 30 70 60 50 40 20 20 10 10 0 10 20 30 40 50 60 Rotational Travel (%) 70 80 90 100 (3 (25 0C): C C (20 ): C 6 C) 5 (15 : C 4 C (10 ): C (05 C): C 2 C) :C 1 30 0 10 20 30 40 50 60 Rotational Travel (%) REV. 12/14 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. 70 80 90 100 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bourns: PTD902-10BAP-B203 PTD902-10C5P-A203 PTD902-10DAP-B203 PTD902-20BAP-C203 PTD904-20BAP-C203 PTD904-20CAP-C203 PTD906-20BAP-C203 PTD908-20BAP-C203 PTD901-2020K-B503 PTD901-2025K-B102 PTD902-2015F-A103 PTD902-2015F-B103 PTD902-2015K-B503 PTD904-1015K-B103 PTD904-1215K-B203 PTD908-1215K-B203 PTD901-2220F-B502 PTD902-2215K-B104 PTD901-2015F-B503 PTD901-2015K-A102 PTD901-2015K-A103 PTD901-2015K-A104 PTD901-2015K-A502 PTD901-2015K-A503 PTD901-2015K-B102 PTD901-2015K-B103 PTD901-2015K-B104 PTD901-2015K-B203 PTD901-2015K-B502 PTD901-2015K-B503 PTD901-2015K-C104 PTD901-2015P-B203 PTD901-2020K-A102 PTD901-2020K-B102 PTD901-2020K-B104 PTD901-20AAG-B203 PTD902-1015K-A102 PTD902-1015K-B102 PTD902-1015P-B203 PTD902-1015P-B502 PTD902-2015K-A104 PTD902-2015K-A502 PTD902-2015K-A503 PTD902-2015K-B103 PTD902-2015K-B502 PTD902-2015P-A203 PTD902-2015P-B203 PTD902-2015P-B502 PTD902-2015P-C504 PTD902-2020K-A103 PTD902-2020K-B103 PTD902-2215K-B203 PTD902-2215K-B204 PTD902-2215K-B502 PTD903-2015P-A203 PTD903-2015P-B203 PTD904-1015P-B203 PTD904-2015K-A203 PTD904-2015K-B203 PTD904-2015P-B203 PTD904-2015P-C203 PTD904-2015P-C204 PTD904-2020K-B103 PTD905-2015P-A203 PTD905-2015P-B203 PTD906-2015P-C203 PTD908-1015P-B203 PTD908-2015P-C203 PTD908-2015P-C504 PTD901-1015F-B103 PTD901-1015K-B103 PTD901-1015K-B503 PTD901-1025K-B503 PTD901-1215F-B103 PTD902-1010K-B203 PTD902-1015F-B103 PTD902-1020K-B203 PTD902-1025K-A103 PTD902-1025K-B503 PTD904-1015F-A104 PTD904-2220K-B203 PTD908-1020F-B103 PTD908-1020F-B502 PTD904-1020K-A103 PTD901-1015F-B203 PTD902-1215K-B503 PTD902-1215F-B104 PTD901-1025K-B203 PTD902-2015F-A203 PTD901-2015F-C103 PTD902-1215K-A502 PTD901-2015F-A105 PTD901-2215F-B103 PTD901-2025K-A203 PTD902-2020K-A104 PTD902-1020K-A103 PTD908-1020K-A103 PTD902-1225F-B203 PTD902-1015K-A104 PTD904-1225F-B203