VIN
EN
GND
FB
VOUT
LMZ10503
VIN VOUT
SS
Cin
CO
Rfbt
Rcomp Ccomp
Rfbb
CSS
1
2
34, EP
5
6, 7
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
LMZ10503 3-A SIMPLE SWITCHER
®
Power Module With 5.5-V Maximum Input Voltage
1
1 Features
1 Integrated Shielded Inductor
Flexible Start-up Sequencing Using External Soft
Start, Tracking, and Precision Enable
Protection Against In-Rush Currents and Faults
Such as Input UVLO and Output Short Circuit
Single Exposed Pad and Standard Pinout for Easy
Mounting and Manufacturing
Pin-to-Pin Compatible With
LMZ10504 (4 A / 20 W Maximum)
LMZ10505 (5 A / 25 W Maximum)
Electrical Specifications
15-W Maximum Total Output Power
Up to 3-A Output Current
Input Voltage Range 2.95 V to 5.5 V
Output Voltage Range 0.8 V to 5 V
±1.63% Feedback Voltage Accuracy Over
Temperature
Performance Benefits
Operates at High Ambient Temperatures
High Efficiency up to 96% Reduces System
Heat Generation
Low Radiated Emissions (EMI) Tested to
EN55022 Class B Standard (EN 55022:2006,
+A1:2007, FCC Part 15 Subpart B: 2007. See
Table 9 and layout information for more
regarding device under test.)
Fast Transient Response for Powering FPGAs
and ASICs
Create a Custom Design Using the LMZ10503
With the WEBENCH®Power Designer
2 Applications
Point-of-Load Conversions From 3.3-V and 5-V
Rails
Space-Constrained Applications
Noise Sensitive Applications (that is, Transceiver,
Medical)
3 Description
The LMZ10503 SIMPLE SWITCHER power module
is a complete, easy-to-use DC-DC solution capable of
driving up to a 3-A load with exceptional power
conversion efficiency, output voltage accuracy, line
and load regulation. The LMZ10503 is available in an
innovative package that enhances thermal
performance and allows for hand or machine
soldering.
The LMZ10503 can accept an input voltage rail
between 2.95 V and 5.5 V and can deliver an
adjustable and highly accurate output voltage as low
as 0.8 V. One megahertz fixed-frequency PWM
switching provides a predictable EMI characteristic.
Two external compensation components can be
adjusted to set the fastest response time, while
allowing the option to use ceramic and/or electrolytic
output capacitors. Externally programmable soft-start
capacitor facilitates controlled startup. The LMZ10503
is a reliable and robust solution with the following
features: lossless cycle-by-cycle peak current limit to
protect for over current or short-circuit fault, thermal
shutdown, input undervoltage lockout, and prebiased
start-up.
Device Information(1)(2)
PART NUMBER PACKAGE BODY SIZE (NOM)
LMZ10503 TO-PMOD (7) 10.16 mm × 9.85 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
(2) Peak reflow temperature equals 245°C. See Design Summary
LMZ1xxx and LMZ2xxx Power Module Family (SNAA214) for
more details.
Typical Application Circuit Efficiency VOUT = 3.3 V
2
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Typical Characteristics.............................................. 7
7 Detailed Description............................................ 10
7.1 Overview................................................................. 10
7.2 Functional Block Diagram....................................... 10
7.3 Feature Description................................................. 10
7.4 Device Functional Modes........................................ 13
8 Application and Implementation ........................ 14
8.1 Application Information............................................ 14
8.2 Typical Application.................................................. 14
8.3 System Examples ................................................... 20
9 Power Supply Recommendations...................... 23
10 Layout................................................................... 23
10.1 Layout Guidelines ................................................. 23
10.2 Layout Examples................................................... 24
10.3 Estimate Power Dissipation and Thermal
Considerations......................................................... 26
10.4 Power Module SMT Guidelines ............................ 27
11 Device and Documentation Support................. 28
11.1 Device Support...................................................... 28
11.2 Documentation Support ........................................ 28
11.3 Receiving Notification of Documentation Updates 28
11.4 Community Resources.......................................... 28
11.5 Trademarks........................................................... 29
11.6 Electrostatic Discharge Caution............................ 29
11.7 Glossary................................................................ 29
12 Mechanical, Packaging, and Orderable
Information........................................................... 29
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision J (September 2015) to Revision K Page
Changed language of WEBENCH list item; added additional content and links for WEBENCH further in data sheet ......... 1
Changed equation 1 in Enable and UVLO .......................................................................................................................... 10
Changes from Revision I (October 2013) to Revision J Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Removed Easy-To-Use PFM 7-Pin Package image ............................................................................................................. 1
Changes from Revision H (April 2013) to Revision I Page
Deleted 10 mils....................................................................................................................................................................... 4
Changed 10 mils................................................................................................................................................................... 23
Added Power Module SMT Guidelines................................................................................................................................. 27
Exposed Pad
Connect to GND
5 FB
6 VOUT
3 SS
1 VIN
2 EN
4 GND
7 VOUT
3
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
5 Pin Configuration and Functions
NDW Package
7-Lead TO-PMOD
Top View
Pin Functions
PIN TYPE DESCRIPTION
NAME NO.
EN 2 Analog Active-high enable input for the device.
Exposed Pad Ground Exposed pad is used as a thermal connection to remove heat from the device. Connect this pad to
the PCB ground plane in order to reduce thermal resistance value. EP must also provide a direct
electrical connection to the input and output capacitors ground terminals. Connect EP to pin 4.
FB 5 Analog Feedback pin. This is the inverting input of the error amplifier used for sensing the output voltage.
Keep the copper area of this node small.
GND 4 Ground Power ground and signal ground. Provide a direct connection to the EP. Place the bottom
feedback resistor as close as possible to GND and FB pin.
SS 3 Analog Soft-start control pin. An internal 2-µA current source charges an external capacitor connected
between SS and GND pins to set the output voltage ramp rate during startup. The SS pin can also
be used to configure the tracking feature.
VIN 1 Power Power supply input. A low ESR input capacitance should be located as close as possible to the
VIN pin and exposed pad (EP).
VOUT 6, 7 Power The output terminal of the internal inductor. Connect the output filter capacitor between VOUT pin
and EP.
4
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) For soldering specifications, refer to the Absolute Maximum Ratings for Soldering (SNOA549).
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN MAX UNIT
VIN, VOUT, EN, FB, SS to GND –0.3 6 V
Power Dissipation Internally Limited
Junction Temperature 150 °C
Peak Reflow Case Temperature (30 sec) 245 °C
Storage Temperature, Tstg –65 150 °C
(1) The human body model is a 100-pF capacitor discharged through a 1.5-kresistor into each pin. Test method is per JESD22-AI14S.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM)(1) ±2000 V
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
VIN to GND 2.95 5.5 V
Junction Temperature (TJ) –40 125 °C
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report.
(2) RθJA measured on a 2.25-in × 2.25-in (5.8 cm x 5.8 cm) 4-layer board, with 1-oz. copper, thirty six thermal vias, no air flow, and 1-W
power dissipation. Refer to Layout or Evaluation Board Application Note AN-2024 LMZ1420x / LMZ1200x Evaluation Board (SNVA422).
6.4 Thermal Information
THERMAL METRIC(1) LMZ10503
UNITNDW (TO-PMOD)
7 PINS
RθJA Junction-to-ambient thermal resistance (2) 20 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 1.9 °C/W
5
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
(1) Minimum and maximum limits are 100% production tested at an ambient temperature (TA) of 25°C. Limits over the operating
temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate
Average Outgoing Quality Level (AOQL).
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
6.5 Electrical Characteristics
Specifications are for TJ= 25°C unless otherwise specified. Minimum and maximum limits are ensured through test, design,
or statistical correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference
purposes only. VIN = VEN = 3.3 V, unless otherwise indicated in the conditions column.
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
SYSTEM PARAMETERS
VFB Total Feedback Voltage
Variation Including Line and
Load Regulation
VIN = 2.95 V to 5.5 V
VOUT = 2.5 V
IOUT = 0 A to 3 A
0.8 V
over the operating junction
temperature range TJof –40°C
to 125°C
0.78 0.82
VFB Feedback Voltage Variation VIN = 3.3 V, VOUT = 2.5
V
IOUT = 0 A
0.8 V
over the operating junction
temperature range TJof –40°C
to 125°C
0.787 0.812
VFB Feedback Voltage Variation VIN = 3.3 V, VOUT = 2.5
V
IOUT = 3 A
0.798 V
over the operating junction
temperature range TJof –40°C
to 125°C
0.785 0.81
VIN(UVLO) Input UVLO Threshold
(Measured at VIN pin)
Rising
2.6 V
over the operating junction
temperature range TJof –40°C
to 125°C
2.95
Falling
2.4
over the operating junction
temperature range TJof –40°C
to 125°C
1.95
ISS Soft-Start Current Charging Current 2 µA
IQNon-Switching Input
Current VFB = 1 V
1.7 mA
over the operating junction
temperature range TJof –40°C
to 125°C
3
ISD Shutdown Quiescent
Current VIN = 5.5 V, VEN = 0 V
260 µA
over the operating junction
temperature range TJof –40°C
to 125°C
500
IOCL Output Current Limit
(Average Current) VOUT = 2.5 V
5.2 A
over the operating junction
temperature range TJof –40°C
to 125°C
3.8 6.7
fFB Frequency Fold-back In current limit 250 kHz
PWM SECTION
fSW Switching Frequency 1000 kHz
over the operating junction temperature range TJof –40°C
to 125°C 750 1160
Drange PWM Duty Cycle Range over the operating junction temperature range TJof –40°C
to 125°C 0% 100%
ENABLE CONTROL
VEN-IH EN Pin Rising Threshold 1.23 V
over the operating junction temperature range TJof –40°C
to 125°C 1.8
VEN-IF EN Pin Falling Threshold 1.06 V
over the operating junction temperature range TJof –40°C
to 125°C 0.8
6
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
Electrical Characteristics (continued)
Specifications are for TJ= 25°C unless otherwise specified. Minimum and maximum limits are ensured through test, design,
or statistical correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference
purposes only. VIN = VEN = 3.3 V, unless otherwise indicated in the conditions column.
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
THERMAL CONTROL
TSD TJfor Thermal Shutdown 145 °C
TSD-HYS Hysteresis for Thermal
Shutdown 10 °C
PERFORMANCE PARAMETERS
ΔVOUT Output Voltage Ripple Refer to Table 1
VOUT = 2.5 V
Bandwidth Limit = 2 MHz
7 mVpk-
pk
ΔVOUT Output Voltage Ripple Refer to Table 5 Bandwidth Limit = 20 MHz 5 mVpk-
pk
ΔVFB /
VFB Feedback Voltage Line
Regulation ΔVIN = 2.95 V to 5.5 V
IOUT = 0 A 0.04%
ΔVOUT /
VOUT Output Voltage Line
Regulation ΔVIN = 2.95 V to 5.5 V
IOUT = 0 A, VOUT = 2.5 V 0.04%
ΔVFB /
VFB Feedback Voltage Load
Regulation IOUT = 0 A to 3 A 0.25%
ΔVOUT /
VOUT Output Voltage Load
Regulation IOUT = 0 A to 3 A
VOUT = 2.5 V 0.25%
EFFICIENCY
ηPeak Efficiency (1 A) VIN =
5 V
VOUT = 3.3 V 96.3%
VOUT = 2.5 V 94.9%
VOUT = 1.8 V 93.3%
VOUT = 1.5 V 92.2%
VOUT = 1.2 V 90.5%
VOUT = 0.8 V 86.9%
ηPeak Efficiency (1 A) VIN =
3.3 V
VOUT = 2.5 V 95.7%
VOUT = 1.8 V 94%
VOUT = 1.5 V 92.9%
VOUT = 1.2 V 91.3%
VOUT = 0.8 V 87.9%
ηFull Load Efficiency (3 A)
VIN = 5 V
VOUT = 3.3 V 94.8%
VOUT = 2.5 V 93%
VOUT = 1.8 V 90.8%
VOUT = 1.5 V 89.3%
VOUT = 1.2 V 87.1%
VOUT = 0.8 V 82.3%
ηFull Load Efficiency (3 A)
VIN = 3.3 V
VOUT = 2.5 V 92.4%
VOUT = 1.8 V 89.8%
VOUT = 1.5 V 88.2%
VOUT = 1.2 V 85.9%
VOUT = 0.8 V 80.8%
7
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
6.6 Typical Characteristics
Unless otherwise specified, the following conditions apply: VIN = VEN = 5 V, CIN is 47 µF 10-V X5R ceramic capacitor; TA=
25°C for efficiency curves and waveforms.
VOUT = 3.3 V
Figure 1. Efficiency
VOUT = 2.5 V
Figure 2. Efficiency
VOUT = 1.8 V
Figure 3. Efficiency
VOUT = 1.5 V
Figure 4. Efficiency
VOUT = 1.2 V
Figure 5. Efficiency
VOUT = 0.8 V
Figure 6. Efficiency
8
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = VEN = 5 V, CIN is 47 µF 10-V X5R ceramic capacitor; TA=
25°C for efficiency curves and waveforms.
VIN = 5 V, RθJA = 20°C/W
Figure 7. Current Derating
VIN = 3.3 V, RθJA = 20°C/W
Figure 8. Current Derating
VIN = 5 V, VOUT = 2.5 V, IOUT = 3 A
Figure 9. Radiated Emissions (EN55022, Class B)
Evaluation Board
VOUT = 2.5 V, IOUT = 0 A
Figure 10. Start-Up
VOUT = 2.5 V, IOUT = 0 A
Figure 11. Prebiased Start-Up
VIN = 3.3 V, VOUT = 2.5 V, IOUT = 0.3 A to 2.7 A to 0.3-A Step
20-MHz Bandwidth Limited. Refer to Table 5 for BOM, includes
optional components
Figure 12. Load Transient Response
9
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = VEN = 5 V, CIN is 47 µF 10-V X5R ceramic capacitor; TA=
25°C for efficiency curves and waveforms.
VIN = 5 V, VOUT = 2.5 V, IOUT = 0.3 A to 2.7 A to 0.3-A step
20-MHz Bandwidth Limited. Refer to Table 5 for BOM, includes
optional components
Figure 13. Load Transient Response
VIN = 3.3 V, VOUT = 2.5 V, IOUT = 3 A,
20 mV/DIV. Refer to Table 5 for BOM
Figure 14. Output Voltage Ripple
VIN = 5 V, VOUT = 2.5 V, IOUT = 3 A,
20 mV/DIV. Refer to Table 5 for BOM
Figure 15. Output Voltage Ripple
ent enb
IN(UVLO) enb
R R
V 1.23V R
u
EN
VIN
Voltage
Mode
Control VOUT
GND
SS
FB
2.2 PH
2.2 PF
2.2 PF
1:
1
2
3
4, EP
5
6, 7
Drivers
P-MOSFET
N-MOSFET
10
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
The LMZ10503 SIMPLE SWITCHER power module is a complete, easy-to-use DC-DC solution capable of
driving up to a 3-A load with exceptional power conversion efficiency, output voltage accuracy, line and load
regulation. The LMZ10503 is available in an innovative package that enhances thermal performance and allows
for hand or machine soldering. The LMZ10503 is a reliable and robust solution with the following features:
lossless cycle-by-cycle peak current limit to protect for overcurrent or short-circuit fault, thermal shutdown, input
undervoltage lockout, and prebiased start-up.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Enable
The LMZ10503 features an enable (EN) pin and associated comparator to allow the user to easily sequence the
LMZ10503 from an external voltage rail, or to manually set the input UVLO threshold. The turnon or rising
threshold and hysteresis for this comparator are typically 1.23 V and 0.15 V respectively. The precise reference
for the enable comparator allows the user to ensure that the LMZ10503 will be disabled when the system
demands it to be.
The EN pin should not be left floating. For always-on operation, connect EN to VIN.
7.3.2 Enable and UVLO
Using a resistor divider from VIN to EN as shown in the schematic diagram below, the input voltage at which the
part begins switching can be increased above the normal input UVLO level according to
(1)
For example, suppose that the required input UVLO level is 3.69 V. Choosing Renb = 10 k, then we calculate
Rent = 20 k.
ss ss
SS FB
t I
CV
u
VIN
EN
GND
VOUT
Renb
Rent
VIN
Cin1
Master Power Supply
VOUT1
VOUT2
CO1
LMZ10503
VIN
EN
GND
LMZ10503
Renb
Rent
VIN
Cin1
11
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Feature Description (continued)
Figure 16. Setting Enable and UVLO
Alternatively, the EN pin can be driven from another voltage source to cater to system sequencing requirements
commonly found in FPGA and other multi-rail applications. Figure 17 shows an LMZ10503 that is sequenced to
start based on the voltage level of a master system rail (VOUT1).
Figure 17. Setting Enable and UVLO Using External Power Supply
7.3.3 Soft-Start
The LMZ10503 begins to operate when both the VIN and EN, voltages exceed the rising UVLO and enable
thresholds, respectively. A controlled soft-start eliminates inrush currents during start-up and allows the user
more control and flexibility when sequencing the LMZ10503 with other power supplies.
In the event of either VIN or EN decreasing below the falling UVLO or enable threshold respectively, the voltage
on the soft-start pin is collapsed by discharging the soft-start capacitor by a 14-µA (typical) current sink to
ground.
7.3.4 Soft-Start Capacitor
Determine the soft-start capacitance with the following relationship:
where
VFB is the internal reference voltage (nominally 0.8 V), ISS is the soft-start charging current (nominally 2 µA)
and CSS is the external soft-start capacitance. (2)
Thus, the required soft-start capacitor per unit output voltage startup time is given by:
(3)
For example, a 4-ms soft-start time will yield a 10-nF capacitance. The minimum soft-start capacitance is 680 pF.
VOLTAGE
TIME
RATIOMETRIC STARTUP
VOUT2
EN
VOUT1
trkt
trkb OUT1
R
RV 1.0V
VIN
EN
GND
SS
Rtrkb
Rtrkt
VIN
Cin1
Master Power
Supply
VOUT1
VOUT2
CO1
VSS
LMZ10503VOUT
12
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
Feature Description (continued)
7.3.5 Tracking
The LMZ10503 can track the output of a master power supply during soft-start by connecting a resistor divider to
the SS pin. In this way, the output voltage slew rate of the LMZ10503 will be controlled by a master supply for
loads that require precise sequencing. When the tracking function is used, a small value soft-start capacitor
should be connected to the SS pin to alleviate output voltage overshoot when recovering from a current limit
fault.
Figure 18. Tracking Using External Power Supply
7.3.6 Tracking - Equal Soft-Start Time
One way to use the tracking feature is to design the tracking resistor divider so that the master supply output
voltage, VOUT1, and the LMZ10503 output voltage, VOUT2, both rise together and reach their target values at the
same time. This is termed ratiometric start-up. For this case, the equation governing the values of tracking divider
resistors Rtrkb and Rtrkt is given by:
(4)
Equation 4 includes an offset voltage, of 200 mV, to ensure that the final value of the SS pin voltage exceeds the
reference voltage of the LMZ10503. This offset will cause the LMZ10503 output voltage to reach regulation
slightly before the master supply. A value of 33 k1% is recommended for Rtrkt as a compromise between high
precision and low quiescent current through the divider while minimizing the effect of the 2-µA soft-start current
source.
For example, if the master supply voltage VOUT1 is 3.3 V and the LMZ10503 output voltage was 1.8 V, then the
value of Rtrkb needed to give the two supplies identical soft-start times would be 14.3 k.Figure 19 shows an
example of tracking using the equal soft-start time.
Figure 19. Timing Diagram for Tracking Using Equal Soft-Start Time
VOLTAGE
TIME
SIMULTANEOUS STARTUP
VOUT2
EN
VOUT1
OUT2 OUT1
V 0.8 V u
trkb trkt
OUT2
0.8V
R R
V 0.8V
u
13
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Feature Description (continued)
7.3.7 Tracking - Equal Slew Rates
Alternatively, the tracking feature can be used to have similar output voltage ramp rates. This is referred to as
simultaneous start-up. In this case, the tracking resistors can be determined based on Equation 5:
(5)
and to ensure proper overdrive of the SS pin:
(6)
For the example case of VOUT1 =5VandVOUT2 = 2.5 V, with Rtrkt set to 33 kas before, Rtrkb is calculated from
the above equation to be 15.5 k.Figure 20 shows an example of tracking using the equal slew rates.
Figure 20. Timing Diagram for Tracking Using Equal Slew Rates
7.3.8 Current Limit
When a current greater than the output current limit (IOCL) is sensed, the ON-time is immediately terminated and
the low-side MOSFET is activated. The low-side MOSFET stays on for the entire next four switching cycles.
During these skipped pulses, the voltage on the soft-start pin is reduced by discharging the soft-start capacitor by
a current sink on the soft-start pin of nominally 14 µA. Subsequent overcurrent events will drain more and more
charge from the soft-start capacitor, effectively decreasing the reference voltage as the output droops due to the
pulse skipping. Reactivation of the soft-start circuitry ensures that when the overcurrent situation is removed, the
part will resume normal operation smoothly.
7.3.9 Overtemperature Protection
When the LMZ10503 senses a junction temperature greater than 145°C (typical), both switching MOSFETs are
turned off and the part enters a standby state. Upon sensing a junction temperature below 135°C (typical), the
part will re-initiate the soft-start sequence and begin switching once again.
7.4 Device Functional Modes
7.4.1 Prebias Start-Up Capability
At start-up, the LMZ10503 is in a prebiased state when the output voltage is greater than zero. This often occurs
in many multi-rail applications such as when powering an ASIC, FPGA, or DSP. The output can be prebiased in
these applications through parasitic conduction paths from one supply rail to another. Even though the
LMZ10503 is a synchronous converter, it will not pull the output low when a prebias condition exists. The
LMZ10503 will not sink current during start-up until the soft-start voltage exceeds the voltage on the FB pin.
Because the device does not sink current it protects the load from damage that might otherwise occur if current
is conducted through the parasitic paths of the load.
VIN
EN
GND
FB
VOUT
LMZ10503
VIN VOUT
SS
Cin
CO
Rfbt
Rcomp Ccomp
Rfbb
CSS
1
2
34, EP
5
6, 7
14
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LMZ10503 is a step-down DC-to-DC power module. It is typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of 3 A. The following design procedure can be used to select
components for the LMZ10503. Alternately, the WEBENCH software may be used to generate complete designs.
When generating a design, the WEBENCH software uses iterative design procedure and accesses
comprehensive databases of components. Please go to www.ti.com for more details.
8.2 Typical Application
Figure 21. Typical Application Circuit
8.2.1 Design Requirements
For this example the following application parameters exist.
VIN =5V
VOUT = 2.5 V
IOUT =3A
ΔVOUT = 20 mVpk-pk
ΔVo_tran = ±20 mVpk-pk
Table 1. Bill of Materials, VIN =3.3Vto5V,VOUT = 2.5 V, IOUT (MAX) = 3 A, Optimized for Electrolytic Input
and Output Capacitance
DESIGNATOR DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N QUANTITY
U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ10503 1
Cin1 150 µF, 6.3 V, 18 mC2, 6.0 x 3.2 x 1.8 mm Sanyo 6TPE150MIC2 1
CO1 330 µF, 6.3 V, 18 mD3L, 7.3 x 4.3 x 2.8
mm Sanyo 6TPE330MIL 1
Rfbt 100 k0603 Vishay Dale CRCW0603100KFKEA 1
Rfbb 47.5 k0603 Vishay Dale CRCW060347K5FKEA 1
Rcomp 15 k0603 Vishay Dale CRCW060315K0FKEA 1
Ccomp 330 pF, ±5%, C0G, 50 V 0603 TDK C1608C0G1H331J 1
CSS 10 nF, ±10%, X7R, 16 V 0603 Murata GRM188R71C103KA01 1
15
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Table 2. Bill of Materials, VIN = 3.3 V, VOUT = 0.8 V, IOUT (MAX) = 3 A, Optimized for Solution Size and
Transient Response
DESIGNATOR DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N QUANTITY
U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ10503TZ 1
Cin1, CO1 47 µF, X5R, 6.3 V 1206 TDK C3216X5R0J476M 2
Rfbt 110 k0402 Vishay Dale CRCW0402100KFKED 1
Rcomp 1.0 k0402 Vishay Dale CRCW04021K00FKED 1
Ccomp 27 pF, ±5%, C0G, 50 V 0402 Murata GRM1555C1H270JZ01 1
CSS 10 nF, ±10%, X7R, 16 V 0402 Murata GRM155R71C103KA01 1
8.2.2 Detailed Design Procedure
LMZ10503 is fully supported by WEBENCH and offers the following: component selection, performance,
electrical, and thermal simulations as well as the Build-It board, for a reduced design time. On the other hand, all
external components can be calculated by following the design procedure below.
1. Determine the input voltage and output voltage. Also, make note of the ripple voltage and voltage transient
requirements.
2. Determine the necessary input and output capacitance.
3. Calculate the feedback resistor divider.
4. Select the optimized compensation component values.
5. Estimate the power dissipation and board thermal requirements.
6. Follow the PCB design guideline.
7. Learn about the LMZ10503 features such as enable, input UVLO, soft start, tracking, prebiased start-up,
current limit, and thermal shutdown.
8.2.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LMZ10503 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
Run electrical simulations to see important waveforms and circuit performance
Run thermal simulations to understand board thermal performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
IN OUT
Lsw
(V V ) D
iL f
u
'
u
> @
L
Osw OUT L ESR
i
C8 f V ( i R )
'
tu u ' ' u
Cin(RMS) 2.5V 2.5V
I 3A 1 1.5A
5V 5V
§ ·
u
¨ ¸
© ¹
Cin(RMS) OUT
I I D(1 D) u
in
2.5V 2.5V
3A 1
5V 5V
C 15 F
1 MHz 50mV
§ · § ·
u u
¨ ¸ ¨ ¸
© ¹ © ¹
t t P
u
OUT
IN
V
DV
OUT
in sw IN
I D (1 D)
Cf V
u u
t
u '
16
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
8.2.2.2 Input Capacitor Selection
A 22-µF or 47-µF, high-quality dielectric (X5R, X7R) ceramic capacitor rated at twice the maximum input voltage
is typically sufficient. The input capacitor must be placed as close as possible to the VIN pin and GND exposed
pad to substantially eliminate the parasitic effects of any stray inductance or resistance on the PCB and supply
lines.
Neglecting capacitor equivalent series resistance (ESR), the resultant input capacitor AC ripple voltage is a
triangular waveform. The minimum input capacitance for a given peak-to-peak value (ΔVIN) of VIN is specified as
follows:
where
the PWM duty cycle, D, is given by Equation 8: (7)
(8)
If ΔVIN is 1% of VIN, this equals to 50 mV and fSW = 1 MHz.
(9)
A second criteria before finalizing the Cin bypass capacitor is the RMS current capability. The necessary RMS
current rating of the input capacitor to a buck regulator can be estimated by:
(10)
(11)
With this high AC current present in the input capacitor, the RMS current rating becomes an important
parameter. The maximum input capacitor ripple voltage and RMS current occur at 50% duty cycle. Select an
input capacitor rated for at least the maximum calculated ICin(RMS).
Additional bulk capacitance with higher ESR may be required to damp any resonance effects of the input
capacitance and parasitic inductance.
8.2.2.3 Output Capacitor Selection
In general, 22-µF to 100-µF, high-quality dielectric (X5R, X7R) ceramic capacitor rated at twice the maximum
output voltage is sufficient given the optimal high-frequency characteristics and low ESR of ceramic dielectrics.
Although, the output capacitor can also be of electrolytic chemistry for increased capacitance density.
Two output capacitance equations are required to determine the minimum output capacitance. One equation
determines the output capacitance (CO) based on PWM ripple voltage. The second equation determines CO
based on the load transient characteristics. Select the largest capacitance value of the two.
The minimum capacitance, given the maximum output voltage ripple (ΔVOUT) requirement, is determined by
Equation 12:
where
the peak to peak inductor current ripple (ΔiL) is equal to Equation 13: (12)
(13)
fbt fbb
OUT fbb
R R
V 0.8V R
u
O
C 42 F t P
O2.4A 0.8V 2.2 H 5V
C4 2.5V (5V 2.5V) 20mV
u u P u
tu u u
step FB IN
OOUT IN OUT
I V L V
C4 V (V V ) Vo_tran
u u u
t
u u u '
O
C 4 F t P
O568 mA
C8 1 MHz 20 mV 568 mA 3 m
tª º
u u u :
¬ ¼
2.5V
5V
L(5V 2.2V)
i 568 mA
2.2 H 1 MHz
u
'
P u
17
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
RESR is the total output capacitor ESR, L is the inductance value of the internal power inductor, where L = 2.2
µH, and fSW = 1 MHz. Therefore, per the design example:
(14)
The minimum output capacitance requirement due to the PWM ripple voltage is:
(15)
(16)
Three mΩis a typical RESR value for ceramic capacitors.
Equation 17 provides a good first pass capacitance requirement for a load transient:
where
Istep is the peak-to-peak load step (for this example Istep = 10% to 90% of the maximum load)
VFB = 0.8 V
and ΔVo_tran is the maximum output voltage deviation, which is ±20 mV. (17)
Therefore the capacitance requirement for the given design parameters is:
(18)
(19)
In this particular design the output capacitance is determined by the load transient requirements.
Table 3 lists some examples of commercially available capacitors that can be used with the LMZ10503.
Table 3. Recommended Output Filter Capacitors
CO(µF) VOLTAGE (V), RESR (m) MAKE MANUFACTURER PART NUMBER CASE SIZE
22 6.3, < 5 Ceramic, X5R TDK C3216X5R0J226M 1206
47 6.3, < 5 Ceramic, X5R TDK C3216X5R0J476M 1206
47 6.3, < 5 Ceramic, X5R TDK C3225X5R0J476M 1210
47 10.0, < 5 Ceramic, X5R TDK C3225X5R1A476M 1210
100 6.3, < 5 Ceramic, X5R TDK C3225X5R0J107M 1210
100 6.3, 50 Tantalum AVX TPSD157M006#0050 D, 7.5 x 4.3 x 2.9 mm
100 6.3, 25 Organic Polymer Sanyo 6TPE100MPB2 B2, 3.5 x 2.8 x 1.9 mm
150 6.3, 18 Organic Polymer Sanyo 6TPE150MIC2 C2, 6.0 x 3.2 x 1.8 mm
330 6.3, 18 Organic Polymer Sanyo 6TPE330MIL D3L, 7.3 x 4.3 x 2.8
mm
470 6.3, 23 Niobium Oxide AVX NOME37M006#0023 E, 7.3 x 4.3 x 4.1 mm
8.2.2.3.1 Output Voltage Setting
A resistor divider network from VOUT to the FB pin determines the desired output voltage as follows:
(20)
Rfbt is defined based on the voltage loop requirements and Rfbb is then selected for the desired output voltage.
Resistors are normally selected as 0.5% or 1% tolerance. Higher accuracy resistors such as 0.1% are also
available.
VIN
EN
GND
FB
LMZ10503 Rfbt Rcomp
Ccomp
Rfbb
VIN
VOUT
18
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
(1) In the special case where the output voltage is 0.8 V, TI recommends to remove Rfbb and keep Rfbt, Rcomp, and Ccomp for a type III
compensation.
The feedback voltage (at VOUT = 2.5 V) is accurate to within –2.5% / +2.5% over temperature and over line and
load regulation. Additionally, the LMZ10503 contains error nulling circuitry to substantially eliminate the feedback
voltage variation over temperature as well as the long term aging effects of the internal amplifiers. In addition the
zero nulling circuit dramatically reduces the 1/f noise of the bandgap amplifier and reference. The manifestation
of this circuit action is that the duty cycle will have two slightly different but distinct operating points, each evident
every other switching cycle.
8.2.2.4 Loop Compensation
The LMZ10503 preserves flexibility by integrating the control components around the internal error amplifier while
using three small external compensation components from VOUT to FB. An integrated type II (two pole, one zero)
voltage-mode compensation network is featured. To ensure stability, an external resistor and small value
capacitor can be added across the upper feedback resistor as a pole-zero pair to complete a type III (three pole,
two zero) compensation network. The compensation components recommended in Table 4 provide type III
compensation at an optimal control loop performance. The typical phase margin is 45° with a bandwidth of 80
kHz. Calculated output capacitance values not listed in Table 4 should be verified before designing into
production. The detailed application note AN-2013 LMZ1050x/LMZ1050xEXT SIMPLE SWITCHER Power
Module (SNVA417) is available to provide verification support. In general, calculated output capacitance values
below the suggested value will have reduced phase margin and higher control loop bandwidth. Output
capacitance values above the suggested values will experience a lower bandwidth and increased phase margin.
Higher bandwidth is associated with faster system response to sudden changes such as load transients. Phase
margin changes the characteristics of the response. Lower phase margin is associated with underdamped ringing
and higher phase margin is associated with overdamped response. Losing all phase margin will cause the
system to be unstable; an optimized area of operation is 30° to 60° of phase margin, with a bandwidth of 100
kHz ±20 kHz.
Figure 22. Loop Compensation Control Components
Table 4. LMZ10503 Compensation Component Values
VIN (V) CO(µF) ESR (m)Rfbt (k)(1) Ccomp (pF)(1) Rcomp (k)(1)
MIN MAX
5
22 2 20 150 47 1
47 2 20 100 100 4.53
100 1 10 71.5 180 2
150 1 5 56.2 270 0.499
150 10 25 100 180 4.53
150 26 50 182 100 8.25
220 15 30 133 160 4.99
220 31 60 200 100 6.98
19
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Table 4. LMZ10503 Compensation Component Values (continued)
VIN (V) CO(µF) ESR (m)Rfbt (k)(1) Ccomp (pF)(1) Rcomp (k)(1)
MIN MAX
3.3
22 2 20 100 56.2 5.62
47 2 20 76.8 120 3.32
100 1 10 49.9 220 1
150 1 5 40.2 430 1
150 10 25 43.2 390 3.32
150 26 50 100 180 4.53
220 15 30 80.6 240 3.32
220 31 60 140 150 4.99
8.2.3 Application Curves
VOUT = 3.3 V
Figure 23. Current Derating
VOUT = 3.3 V
Figure 24. Efficiency
Figure 25. Radiated Emissions (EN 55022, Class B)
VIN
EN
GND FB
VIN VOUT
SS
Cin1
CO1
Rfbt
Rcomp
Ccomp
Rfbb
CSS
U1
VOUT
LMZ10503 CO2 CO3
1
2
34, EP
5
6, 7 Optional
+
Cin2
Optional
20
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
(1) Optional components, include for low input and output voltage ripple.
8.3 System Examples
8.3.1 Application Schematic for 3.3-V to 5-V Input and 2.5-V Output With Optimized Ripple and Transient
Response
The compensation for each solution was optimized to work over the full input range. Many applications have a
fixed input voltage rail. It is possible to modify the compensation to obtain a faster transient response for a given
input voltage operating point.
Figure 26. Optimized Schematic for 2.5-V Output Based on 3.3-V to 5-V Input
Table 5. Bill of Materials, VIN =3.3Vto5V,VOUT = 2.5 V, IOUT (MAX) = 3 A, Optimized for Low Input and
Output Ripple Voltage and Fast Transient Response
DESIGNATOR DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N QTY.
U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ10503 1
Cin1 22 µF, X5R, 10 V 1210 AVX 1210ZD226MAT 2
Cin2(1) 220 µF, 10 V, AL-
Elec E Panasonic EEE1AA221AP 1
CO1(1) 4.7 µF, X5R, 10 V 0805 AVX 0805ZD475MAT 1
CO2(1) 22 µF, X5R, 6.3 V 1206 AVX 12066D226MAT 1
CO3 100 µF, X5R, 6.3 V 1812 AVX 18126D107MAT 1
Rfbt 75 k0402 Vishay Dale CRCW040275K0FKED 1
Rfbb 34.8 k0402 Vishay Dale CRCW040234K8FKED 1
Rcomp 1 k0402 Vishay Dale CRCW04021K00FKED 1
Ccomp 220 pF, ±5%, C0G,
50 V 0402 Murata GRM1555C1H221JA01D 1
CSS 10 nF, ±10%, X7R,
16 V 0402 Murata GRM155R71C103KA01 1
Table 6. Output Voltage Setting (Rfbt = 75 k)
VOUT Rfbb
3.3V 23.7 k
2.5 V 34.8 k
1.8 V 59 k
1.5 V 84.5 k
1.2 V 150 k
0.9 V 590 k
VIN
EN
GND
FB
VIN VOUT
SS
Cin1
CO1
Rfbt
Rcomp Ccomp
Rfbb
CSS
U1
VOUT
LMZ10503
Cin2
Cin3
CO2 CO3
Cin4
Cin5 +Ren1
1
2
34, EP
5
6, 7
21
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
8.3.2 Application Schematic for 3.3-V to 5-V Input and 2.5-V Output
The compensation for each solution was optimized to work over the full input range. Many applications have a
fixed input voltage rail. It is possible to modify the compensation to obtain a faster transient response for a given
input voltage operating point.
Figure 27. Schematic for 2.5-V Output Based on 3.3-V to 5-V Input
Table 7. Bill of Materials for Evaluation Board, VIN =3.3Vto5V,VOUT = 2.5 V, IOUT (MAX) =3A
DESIGNATOR DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N QUANTITY
U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ10503 1
Cin1 1 µF, X7R, 16 V 0805 TDK C2012X7R1C105K 1
Cin2, CO1 4.7 µF, X5R, 6.3 V 0805 TDK C2012X5R0J475K 2
Cin3, CO2 22 µF, X5R, 16 V 1210 TDK C3225X5R1C226M 2
Cin4 47 µF, X5R, 6.3 V 1210 TDK C3225X5R0J476M 1
Cin5 220 µF, 10 V, AL-Elec E Panasonic EEE1AA221AP 1
CO3 100 µF, X5R, 6.3 V 1812 TDK C4532X5R0J107M 1
Rfbt 75 k0805 Vishay Dale CRCW080575K0FKEA 1
Rfbb 34.8 k0805 Vishay Dale CRCW080534K8FKEA 1
Rcomp 1.1 k0805 Vishay Dale CRCW08051K10FKEA 1
Ccomp 180 pF, ±5%, C0G, 50 V 0603 TDK C1608C0G1H181J 1
Ren1 100 k0805 Vishay Dale CRCW0805100KFKEA 1
CSS 10 nF, ±5%, C0G, 50 V 0805 TDK C2012C0G1H103J 1
Table 8. Output Voltage Setting (Rfbt = 75 k)
VOUT Rfbb
3.3V 23.7 k
2.5 V 34.8 k
1.8 V 59 k
1.5 V 84.5 k
1.2 V 150 k
0.9 V 590 k
VIN
EN
GND
FB
VIN VOUT
SS
Cin1
CO1
Rfbt
Rcomp Ccomp
Rfbb
CSS
U1
VOUT
LMZ10503
Cin2
Cin3
1
2
34, EP
5
6, 7
22
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
8.3.3 EMI Tested Schematic for 2.5-V Output Based on 3.3-V to 5-V Input
The compensation for each solution was optimized to work over the full input range. Many applications have a
fixed input voltage rail. It is possible to modify the compensation to obtain a faster transient response for a given
input voltage operating point.
Figure 28. EMI Tested Schematic for 2.5-V Output Based on 3.3-V to 5-V Input
Table 9. Bill of Materials, VIN =5V,VOUT = 2.5 V, IOUT (MAX) = 3 A, Tested With EN55022 Class B Radiated
Emissions
DESIGNATOR DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N QUANTITY
U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ10503 1
Cin1 1 µF, X7R, 16 V 0805 TDK C2012X7R1C105K 1
Cin2 4.7 µF, X5R, 6.3 V 0805 TDK C2012X5R0J475K 1
Cin3 47 µF, X5R, 6.3 V 1210 TDK C3225X5R0J476M 1
CO1 100 µF, X5R, 6.3 V 1812 TDK C4532X5R0J107M 1
Rfbt 75 k0805 Vishay Dale CRCW080575K0FKEA 1
Rfbb 34.8 k0805 Vishay Dale CRCW080534K8FKEA 1
Rcomp 1.1 k0805 Vishay Dale CRCW08051K10FKEA 1
Ccomp 180 pF, ±5%, C0G, 50 V 0603 TDK C1608C0G1H181J 1
CSS 10 nF, ±5%, C0G, 50 V 0805 TDK C2012C0G1H103J 1
Table 10. Output Voltage Setting (Rfbt = 75 k)
VOUT Rfbb
3.3 V 23.7 k
2.5 V 34.8 k
1.8 V 59 k
1.5 V 84.5 k
1.2 V 150 k
0.9 V 590 k
23
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
9 Power Supply Recommendations
The LMZ10503 device is designed to operate from an input voltage supply range between 2.95 V and 5.5 V. This
input supply should be well regulated and able to withstand maximum input current and maintain a stable
voltage. The resistance of the input supply rail should be low enough that an input current transient does not
cause a high enough drop at the LMZ10503 supply voltage that can cause a false UVLO fault triggering and
system reset. If the input supply is more than a few inches from the LMZ10503, additional bulk capacitance may
be required in addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47-
μF or 100-μF electrolytic capacitor is a typical choice.
10 Layout
10.1 Layout Guidelines
The PCB copper heat sink must be connected to the exposed pad (EP). Approximately thirty six, 8 mil thermal
vias spaced 59 mils (1.5 mm) apart must connect the top copper to the bottom copper. For an extended
discussion and formulations of thermal rules of thumb, refer to AN-2020 Thermal Design By Insight, Not
Hindsight (SNVA419). For an example of a high thermal performance PCB layout with RθJA of 20°C/W, refer to
the evaluation board application note AN-2022 LMZ1050x Evaluation Board (SNVA421) and for results of a study
of the effects of the PCB designs, refer to AN-2026 Effect of PCB Design on Thermal Performance of SIMPLE
SWITCHER Power Modules (SNVA424).
PCB layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a
DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce and resistive voltage drop in
the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability.
Good layout can be implemented by following a few simple design rules.
1. Minimize area of switched current loops.
From an EMI reduction standpoint, it is imperative to minimize the high di/dt current paths. The high current
that does not overlap contains high di/dt, see Figure 29. Therefore physically place input capacitor (Cin1) as
close as possible to the LMZ10503 VIN pin and GND exposed pad to avoid observable high-frequency noise
on the output pin. This will minimize the high di/dt area and reduce radiated EMI. Additionally, grounding for
both the input and output capacitor should consist of a localized top side plane that connects to the GND
exposed pad (EP).
2. Have a single point ground.
The ground connections for the feedback, soft-start, and enable components should be routed only to the
GND pin of the device. This prevents any switched or load currents from flowing in the analog ground traces.
If not properly placed, poor grounding can result in degraded load regulation or erratic output voltage ripple
behavior. Provide the single point ground connection from pin 4 to EP.
3. Minimize trace length to the FB pin.
Both feedback resistors, Rfbt and Rfbb, and the compensation components, Rcomp and Ccomp, should be
located close to the FB pin. Since the FB node is high impedance, keep the copper area as small as
possible. This is most important as relatively high value resistors are used to set the output voltage.
4. Make input and output bus connections as wide as possible.
This reduces any voltage drops on the input or output of the converter and maximizes efficiency. To optimize
voltage accuracy at the load, ensure that a separate feedback voltage sense trace is made at the load. Doing
so will correct for voltage drops and provide optimum output accuracy.
5. Provide adequate device heat-sinking.
Use an array of heat-sinking vias to connect the exposed pad to the ground plane on the bottom PCB layer.
If the PCB has multiple copper layers, thermal vias can also be employed to make connection to inner layer
heat-spreading ground planes. For best results use a 6 × 6 via array with minimum via diameter of 8 mils
thermal vias spaced 59 mils (1.5 mm). Ensure enough copper area is used for heat-sinking to keep the
junction temperature below 125°C.
SS
FB
GND
VIN
1 2 3 4 5 6 7
Top View
VIN
COUT
VOUT
RENT
GND
Thermal Vias
VOUT
CIN
GND
RENB
CFF
RFBT
RFBB
GND Plane
EXPOSED PAD
CSS
EN
VOUT
24
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
10.2 Layout Examples
Figure 29. Critical Current Loops to Minimize
Figure 30. PCB Layout Guide
Figure 31. Top Copper
25
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Layout Examples (continued)
Figure 32. Internal Layer 1 (Ground)
Figure 33. Internal Layer 2 (Ground and Signal Traces)
Figure 34. Bottom Copper
o
o
2
2500 C cm
Board Area_cm W
C
69.5W
u
t u
o2
2
CA
500 C cm
Board Area_cm W
u
t u
T
o o o o
CA 125 C 85 C C C
1.9 69.5
0.56 W W W
T
J(MAX) A(MAX)
CA JC
IC_LOSS
T T
P
T t T
26
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
10.3 Estimate Power Dissipation and Thermal Considerations
Use the current derating curves in the Typical Characteristics section to obtain an estimate of power loss
(PIC_LOSS). For the design case of VIN =5V,VOUT = 2.5 V, IOUT =3A,TA(MAX) = 85°C , and TJ(MAX) = 125°C, the
device must see a thermal resistance from case to ambient (θCA) of less than:
(21)
(22)
Given the typical thermal resistance from junction to case (θJC) to be 1.9°C/W (typical). Continuously operating at
a TJgreater than 125°C will have a shorten life span.
To reach θCA = 69.5°C/W, the PCB is required to dissipate heat effectively. With no airflow and no external heat,
a good estimate of the required board area covered by 1-oz. copper on both the top and bottom metal layers is:
(23)
(24)
As a result, approximately 7.2 square cm of 1-oz. copper on top and bottom layers is required for the PCB
design.
27
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
10.4 Power Module SMT Guidelines
The recommendations below are for a standard module surface mount assembly
Land Pattern Follow the PCB land pattern with either soldermask defined or non-soldermask defined pads
Stencil Aperture
For the exposed die attach pad (DAP), adjust the stencil for approximately 80% coverage of the PCB land
pattern
For all other I/O pads use a 1:1 ratio between the aperture and the land pattern recommendation
Solder Paste Use a standard SAC Alloy such as SAC 305, type 3 or higher
Stencil Thickness 0.125 to 0.15 mm
Reflow - Refer to solder paste supplier recommendation and optimized per board size and density
Maximum number of reflows allowed is one
Refer to Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214) for reflow information.
Figure 35. Sample Reflow Profile
Table 11. Sample Reflow Profile Table
PROBE MAX TEMP
(°C) REACHED
MAX TEMP TIME ABOVE
235°C REACHED
235°C TIME ABOVE
245°C REACHED
245°C TIME ABOVE
260°C REACHED
260°C
1242.5 6.58 0.49 6.39 0.00 0.00
2242.5 7.10 0.55 6.31 0.00 7.10 0.00
3241.0 7.09 0.42 6.44 0.00 0.00
28
LMZ10503
SNVS641K JANUARY 2010REVISED MAY 2017
www.ti.com
Product Folder Links: LMZ10503
Submit Documentation Feedback Copyright © 2010–2017, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.1.2 Development Support
11.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LMZ10503 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
Run electrical simulations to see important waveforms and circuit performance
Run thermal simulations to understand board thermal performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
AN-2027 Inverting Application for the LMZ14203 SIMPLE SWITCHER Power Module (SNVA425)
Absolute Maximum Ratings for Soldering (SNOA549)
AN-2022 LMZ1050x Evaluation Board (SNVA421)
AN-2024 LMZ1420x / LMZ1200x Evaluation Board (SNVA422)
AN-2013 LMZ1050x/LMZ1050xEXT SIMPLE SWITCHER Power Module (SNVA417)
AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419)
AN-2026 Effect of PCB Design on Thermal Performance of SIMPLE SWITCHER Power Modules (SNVA424)
Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214)
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
29
LMZ10503
www.ti.com
SNVS641K JANUARY 2010REVISED MAY 2017
Product Folder Links: LMZ10503
Submit Documentation FeedbackCopyright © 2010–2017, Texas Instruments Incorporated
Community Resources (continued)
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.7 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LMZ10503TZ-ADJ/NOPB ACTIVE TO-PMOD NDW 7 250 RoHS (In
Work) & Green
(In Work)
CU SN Level-3-245C-168 HR -40 to 125 LMZ10503
TZ-ADJ
LMZ10503TZE-ADJ/NOPB ACTIVE TO-PMOD NDW 7 45 RoHS (In
Work) & Green
(In Work)
CU SN Level-3-245C-168 HR -40 to 125 LMZ10503
TZ-ADJ
LMZ10503TZX-ADJ/NOPB ACTIVE TO-PMOD NDW 7 500 RoHS (In
Work) & Green
(In Work)
CU SN Level-3-245C-168 HR -40 to 125 LMZ10503
TZ-ADJ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2017
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMZ10503TZ-ADJ/NOPB TO-
PMOD NDW 7 250 330.0 24.4 10.6 14.22 5.0 16.0 24.0 Q2
LMZ10503TZX-ADJ/NOP
BTO-
PMOD NDW 7 500 330.0 24.4 10.6 14.22 5.0 16.0 24.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 27-May-2018
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMZ10503TZ-ADJ/NOPB TO-PMOD NDW 7 250 367.0 367.0 45.0
LMZ10503TZX-ADJ/NOPB TO-PMOD NDW 7 500 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 27-May-2018
Pack Materials-Page 2
MECHANICAL DATA
NDW0007A
www.ti.com
TZA07A (Rev D)
TOP SIDE OF PACKAGE
BOTTOM SIDE OF PACKAGE
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LMZ10503TZ-ADJ/NOPB LMZ10503TZE-ADJ/NOPB LMZ10503TZX-ADJ/NOPB