Stratum 3E High Stability Oven Stabilized Oscillator OH200-Series 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Connor-Winfield's high stability OH200series are exceptionally precise frequency standards, excellent for use in cellular base stations, test equipment, Synchronous Ethernet, VSAT and Stratum 3E applications These unique OCXO and OCVCXO products provide temperature stabilities in the range of 3 ppb to 25 ppb, over the commercial, extended commercial or the industrial temperature range. Power requirements are 3W over the commercial temperature range and 4.5W over the industrial temperature range. Additionally, excellent aging is achieved through the use of overtone SC cut crystals. The OH200 series is available with CMOS logic or Sinewave output along with Electronic Frequency Tuning. These oscillators provide outstanding phase noise that varies depending on frequency. Frequencies are available from 5.0 to 40.0 MHz. Allan Variance specifications are rated for primary reference standards. Warm up times are on the order of 5 minutes to 0.10 ppm of final frequency. 32 12 F 3C 00 61 Hz 0- M 20 .8 12 2 OH 1 90 78 56 34 12 Fax: 630- 851- 5040 Description Features * Frequency Range: 5.0 to 40.0 MHz * OCXO - Fixed Frequency * OCVCXO - Voltage Controlled Frequency * 3.3 Vdc, 5.0 Vdc or 12.0 Vdc Operation * Available Frequency Stabilities: 3 ppb, 5 ppb, 10 ppb or 25 ppb * Available Temperature Ranges: 0 to 70C, -20 to 70C, -40 to 70C or -40 to 85C * Low Phase Noise / Phase Jitter * Available Outputs: CMOS or Sinewave * Package: 1.1" x 1.4" x 0.5" (CO-8) * RoHS Compliant / Lead Free Ordering Information OH200Package OH200- = 1.1x1.4 CO8 6 10 03 C Temperature Range Frequency Stability 06 = 3 ppb 10 = 5 ppb 20 = 10 ppb 50 = 25 ppb Supply Voltage Output Type OCXO Type 03 = 3.3 Vdc 05 = 5.0 Vdc 12 = 12.0 Vdc C = CMOS S = Sinewave F = Fixed Freq. V = Voltage Controlled Freq. 5 = 0 to 70C 6 = -40 to 85C 7 = -20 to 70C 8 = -40 to 70C F {(Fmax-Fmin)/(2*Fo)} - 012.8M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Amount of numbers after the decimal point. M = MHz Example Part Number: OH200-61003CF-012.8M = 1.1" x 1.4" x 0.5" CO-8 package, -40 to 85C temperature range, 5.0 ppb frequency stability, 3.3 Vdc supply voltage, CMOS square wave output, fixed frequency OCXO, 12.8 MHz output frequency. To order a OH200-61003CF with an output frequency of: 6.4 MHz = OH200-61003CF-006.4M To order a OH200-61003CF with an output frequency of 16.384 MHz = OH200-61003CF-016.384M. Bulletin Page Revision Date Cx193 1 of 11 13 May 2013 OH200-712005SV-040.0M = 1.1" x 1.4" x 0.5" CO-8 package, -20 to 70C temperature range, 10.0 ppb frequency stability, 5.0 Vdc supply voltage, Sinewave output, voltage controlled output frequency OCVCXO, 40 MHz output frequency. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Parameter Storage Temperature Supply Voltage (Vcc) Control Voltage (Vc) Operating Supply Voltage 3.3 Vdc (Vcc) Operating Supply Voltage 5.0 Vdc (Vcc) Operating Supply Voltage 12 Vdc (Vcc) Absolute Maximum Ratings Minimum -55 -0.5 -0.5 3.13 4.75 11.40 Nominal 3.30 5.00 12.00 Maximum 125 13.5 7.0 3.47 5.25 12.60 Units C Vdc Vdc Vdc Vdc Vdc Notes Absolute Ratings: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only. The functional operation of the device at those or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to conditions outside the "recommended operating conditions" for any extended period of time may adversely impact device reliability and result in failures not covered by warranty. Parameter Center Frequency: (Fo) Operating Temperature Range: Temperature Code 5 Temperature Code 6 Temperature Code 7 Temperature Code 8 Frequency Calibration: Frequency Stability vs. Change in Temperature: Stability Code 06 Stability Code 10 Stability Code 20 Stability Code 50 Frequency Stability vs. Load Frequency Stability vs. Voltage Aging: Daily: 5 MHz to 20 MHz >20 MHz to 40 MHz Aging: First Year: 5 MHz to 20 MHz >20 MHz to 40 MHz Lifetime Tolerance: (20 Years) 5 MHz to 20 MHz- >20 MHz to 40 MHz Supply Voltage: (Vcc) Voltage Code 03 Voltage Code 05 Voltage Code 12 Power Consumption: Turn-On 0 to 70C Models -20 to 70C Models -20 to 75C Models -40 to 85C Models Power Consumption: Steady State @ 25C 0 to 70C Models -20 to 70C Models -20 to 75C Models -40 to 85C Models Phase Jitter: (BW: 10 Hz to Fo/2) Models with Fo: 5 MHz to 20 MHz Models with Fo: >20 MHz to 40 MHz Short Term Allan Deviation (1s) Start-Up Time: Warm Up Time @ 25C: Operating Specifications Minimum Nominal Maximum 0 -40 -20 -40 -0.1 - 70 85 70 70 0.1 C C C C ppm @ 25C -3.0 -5.0 -10.0 -25.0 -5.0 -5.0 - 3.0 5.0 10.0 25.0 5.0 5.0 ppb ppb ppb ppb ppb ppb 1 1 1 1 5% 5% -1.0 -2.0 - 1.0 2.0 ppb/day ppb/day 2 2 -50 -100 - 50 100 ppb ppb -300 -500 - 300 500 ppb ppb 3 3 3.13 4.75 11.40 3.30 5.00 12.00 3.47 5.25 12.60 Vdc Vdc Vdc 4 4 4 - - 3.00 3.20 3.30 3.80 W W W W 5 5 5 5 - - 1.10 1.10 1.20 1.50 W W W W 5 5 5 5 - 1.0E-11 - 1.0 2.0 500 5 ps rms ps rms rms ms minutes 6 5.0 - 40.0 Notes: 1. Frequency stability vs. change in temperature [(Fmax-Fmin)/(2*Fo)]. 2. At time of shipment after 48 hours of operation. 3. Inclusive of calibration, operating temperature, supply voltage change, load change and 20 years aging. 4. Supply voltage must reach Vcc levels monotonically within a ramp-up time of <12 ms. 5. Measured with Vcc = Nominal, in calm air. 6. Measured @ 25C, within 5 minutes, referenced one hour after turn-on. 7. To ensure proper operation of OCVCXO's the control voltage input must be biased the nominal control voltage. Failure to bias the Vc input will cause an unstable output condition. Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Units MHz Bulletin Page Revision Date Notes Cx193 2 of 5 11 13 May 2013 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Phase Noise Characteristics Typical Phase Noise for OXCO's with CMOS Output SSB Phase Noise 5 - 12 MHz @1Hz offset @ 10Hz offset @ 100Hz offset @ 1KHz offset @ 10KHz offset @ 100KHz offset 12.1- 20 MHz -85 -115 -140 -145 -150 -150 -80 -110 -135 -140 -150 -150 20.1 - 30 MHz -70 -100 -125 -140 -150 -150 30.1 - 40 MHz -65 -95 -120 -140 -150 -150 Units dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz OCVCXO Input Characteristics (OCXO Type Code V) Parameter Control Voltage Range: 3.3 Vdc Models 5.0 Vdc Models 12.0 Vdc Models Frequency Pullability: Models with Fo 5 to 20 MHz Models with Fo >20 to 40 MHz Input Impedance Minimum Nominal Maximum Units Notes 0.30 0.50 0.50 1.65 2.50 2.50 3.00 4.50 4.50 V V V Vcc = 3.3 Vdc Vcc = 5.0 Vdc Vcc = 12.0 Vdc 0.4 0.6 100K - - ppm ppm Ohms 7 7 Notes CMOS Output Characteristics (Output Code C) Parameter Load Output Voltage: 3.3 Vdc Models High (Voh) Low (Vol) 5.0 Vdc Models High (Voh) Low (Vol) 12.0 Vdc Models High (Voh) Low (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% Spurious Output Minimum Nominal Maximum Units 3.0 4.7 4.7 45 - 50 - 0.4 0.4 0.4 55 6 -80 V - 15 - pF V V % ns dBc Sinewave Output Characteristics (Output Code S) Parameter Load Output Power Harmonics Spurious Minimum 5.0 - Nominal 50 - Maximum -30 -80 Units Ohms dBm: dBc dBc Notes Package Characteristics OH200 Package Hermetically sealed, resistive welded package with grounded case. Environmental Characteristics Shock Sinusoidal Vibration Random Vibration Moisture Marking Permanency Attachment Method PCB Resistance to Solder Heat Solder Process 500 G's 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. 0.06" D.A. or 10G's Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. 5.35 G's rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Per MIL-STD-202G, Method 215J. Through Hole Mounted Per MIL-STD-202G, Method 210, Condition E. RoHS compliant, lead free. See solder profile. Bulletin Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Page Revision Date Cx193 3 of 5 11 13 May 2013 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Re stabilization Time Off Time <1 Hour <6 Hour <24 Hour 1 to 16 Days >16 Days Re stabilization Time <2 Hours * <12 Hours * <48 Hours * 48 Hours + 1/4 Off Time * <6 Days * * For a given off time, the time required to meet daily aging, short term stability and TEV requirements. Package Outline Package Marking 0.500 Max. 12.70mm 0.035 Dia. 0.88mm Dia. 0.244 6.2mm 0.025 0.635mm 1232 1.417 36mm 1 0.600 15.24mm 5 0.700 17.78mm OH200-61003CF 12.8 MHz 123456789012 123456789012 Bottom View 4 1.063 0.350 27mm 8.9mm 2 3 Date Code (YYWW) Model Number Output Frequency Serial # Barcode Serial Number Pin 1 0.700 17.78mm 1.000 25.4mm Keep Out Area: Under the OCXO is a keep out area, do not place any parts in this area. Test Circuit Vcc Vcc 10 uF to 100 uF 0.01 uF Pin Connections Pin Connection 1: Control Voltage or N/C 2: N/C 3: Supply Voltage (Vcc) 4: Output 5: Ground (Case) Output N/C 15 pF Total Output Load N/C Ground or Control Voltage Solder Profile Temperature 260C CMOS Output Waveform 260C 220C 90% 180C 150C 120C 50% 10% 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Bulletin Page Revision Date Cx193 4 of 5 11 13 May 2013 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Revision History Rev 00, Rev 01, Rev 02, Rev 03, Rev 04, Rev 05, Rev 06, Rev 07, Rev 08, Rev 09, Rev 10, Rev 11, New release, 10/16/09. Added -20 to 75C and 50ppb stability. 02/09/10. Changed 75C to 70C. 03/29/10. Added 8 = -40 to 70C temperature code. 04/05/10. Corrected temperature on page 2, from -20 to 80c to -40 to 70C. 05/19/11. Updated power consumption. 07/27/11. Added sinewave models to the data sheet. 09/08/11. Changed package height from 0.530" to 0.500". 01/23/12. Changed frequency stability from "Absolute" to "+/-" with note 1 added as reference. 03/821/12. Changed marking to Label marking. 08/22/12. Added application note information. 12/07/12. Changed note 4 and removed note from power supply line. and added absolute note. 05/13/13. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Bulletin Page Revision Date Cx193 5 of 5 11 13 May 2013