QL6325-6PQ208C - QuickLogic Corp.

www.quicklogic.com

•

• • • • • •

Device Highlights

Flexible Programmable Logic

• 0.25 µ, 5 layer metal CMOS process

• 2.5 V Vcc, 2.5/3.3 V dive capable I/O

• Up to 4032 logic cells

• Up to 583,000 max system gates

• Up to 347 I/O

Embedded Dual Port SRAM

• Up to thirty-six 2,304-bit dual port SRAM blocks

• Up to 82,900 RAM bits

• RAM/ROM/FIFO Wizard for automatic

configuration

• Configurable and cascadable

Applications

• Signal processing operators

• Signal processing functions

• Networking/communications for VoIP

• Speech/voice processing

• Channel coding

Programmable I/O

• High performance: <3.2 ns Tco

• Programmable slew rate control

• Programmable I/O standards:

LVTTL, LVCMOS, PCI, GTL+, SSTL2,

and SSTL3

Eight independent I/O banks

Three register configurations: input, output and

output enable

Advanced Clock Network

• Nine global clock networks

One dedicated

Eight programmable

• Sixteen I/O (high-drive) networks

• Twenty quad-net networks: five per quadrant

Figure 1: Eclipse Block Diagram

Embedded RAM BlocksPLL PLL

Fabric

Embedded RAM BlocksPLL PLL

Combining Performance, Density, and Embedded RAM

Eclipse Family Data Sheet

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QuickWorks Design Software

The QuickWorks® package provides the most complete ESP and FPGA software solution from design entry

to logic synthesis, to place and route to simulation. The packages provide a solution for designers who use

third party tools from Cadence, Mentor, OrCAD, Synopsys, Viewlogic and other third-party tools for design

entry, synthesis, or simulation.

Process Data

Eclipse is fabricated on a 0.25 μm five-layer metal CMOS process. The core voltage is 2.5 V VCC supply and

3.3 V tolerant I/O with the addition of 3.3 V VCCIO. Eclipse is available in commercial, industrial, and military

temperature grades.

Programmable Logic Architectural Overview

The Eclipse logic cell structure is presented in Figure 2. This architectural feature addresses current register-

intensive designs.

Table 1: Eclipse Product Family Members

QL6250 QL6325 QL6500 QL6600

Max Gates 248,160 320,640 488,064 583,008

Logic Array 40x24 48x32 64x48 72x56

Logic Cells 960 1,536 3,072 4,032

Max Flip-Flops 2,670 4,002 7,185 9,105

Max I/O 250 310 347 347

RAM Modules 20 24 32 36

RAM bits 46,100 55,300 73,700 82,900

Packages

PQFP 208 208 - -

PBGA (1.27 mm) - - 516 516

FPBGA (1.0 mm) 484 484 484 484

LFBGA (0.8 mm) 280 280 280 280

Table 2: Max I/O per Device /Package Combination

Device 208 PQFP 280 FPBGA 484 PBGA 516 PBGA

QL6250 99 163 250 -

QL6325 99 163 310 -

QL6500 - 163 327 347

QL6600 -163 327 347

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 2: Eclipse Logic Cell

The second register has a two-to-one multiplexer controlling its input. The register can be loaded from the NZ

output or directly from a dedicated input.

NOTE: The input “PP” is not an “input” in the classical sense. It can only be tied high or low using default

links only and is used to select which path “NZ” or “PS” is used as an input to the register. All other inputs

can be connected not only to “tiehi” and “tielo” but to multiple routing channels as well.

The complete logic cell consists of 2 six-input AND gates, 4 two-input AND gates, 7 two-to-one multiplexers,

and 2 D flip-flop with asynchronous SET and RESET controls. The cell has a fan-in of 30 (including register

control lines) and fits a wide range of functions with up to 17 simultaneous inputs. It has 6 outputs;

4 combinatorial and 2 registered. The high logic capacity and fan-in of the logic cell accommodate many user

functions with a single level of logic delay while other architectures require two or more levels of delay.

Table 3: Performance Standards

Function Description Slowest Speed Grade Fastest Speed Grade

Multiplexer 16:1 5 ns 2.8 ns

Parity Tree 24 6 ns 3.4 ns

36 6 ns 3.4 ns

Counter 16 bit 250 MHz 450 MHz

32 bit 250 MHz 450 MHz

FIFO

128 x 32 155 MHz 280 MHz

256 x 16 155 MHz 280 MHz

128 x 64 155 MHz 280 MHz

Clock to Out 4.5 ns 2.5 ns

System

clock 200 MHz 400 MHz

Q2Z

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

RAM Modules

The Eclipse Family includes multiple dual-port 2,304-bit RAM modules for implementing RAM, ROM and

FIFO functions. Each module is user-configurable into four different block organizations. Modules can also be

cascaded horizontally to increase their effective width or vertically to increase their effective depth as shown

in Figure 3. The RAM can also be configured as a modified Harvard Architecture, similar to those found in

DSPs.

Figure 3: 2,304-bit Eclipse RAM Module

The number of RAM modules varies from 20 to 36 blocks within the Eclipse family, for a total of 46.1 to 82.9

K bits of RAM. Using two “mode” pins, designers can configure each module into 128 x 18 (Mode 0), 256 x

9 (Mode 1), 512 x 4 (Mode 2), or 1024 x 2 blocks (Mode 3). The blocks are also easily cascadable to increase

their effective width and/or depth. See Figure 4.

Figure 4: Cascaded RAM Modules

The RAM modules are dual-port, with completely independent READ and WRITE ports and separate READ

and WRITE clocks. The READ ports support asynchronous and synchronous operation, while the WRITE

ports support synchronous operation. Each port has 18 data lines and 10 address lines, allowing word lengths

of up to 18 bits and address spaces of up to 1024 words. Depending on the mode selected, however, some

higher order data or address lines may not be used.

MODE[1:0]

WA[9:0]

WD[17:0]

WCLK

SYNCRD

RA[9:0]

RD[17:0]

RCLK

WDATA

RDATA

WADDR

WDATA

RADDR

RAM

Module

(2,304 bits)

RAM

Module

(2,304 bits)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

The Write Enable (WE) line acts as a clock enable for synchronous write operation. The Read Enable (RE) acts

as a clock enable for synchronous READ operation (ASYNCRD input low), or as a flow-through enable for

asynchronous READ operation (ASYNCRD input high).

Designers can cascade multiple RAM modules to increase the depth or width allowed in single modules by

connecting corresponding address lines together and dividing the words between modules.

A similar technique can be used to create depths greater than 512 words. In this case address signals higher

than the ninth bit are encoded onto the write enable (WE) input for WRITE operations. The READ data outputs

are multiplexed together using encoded higher READ address bits for the multiplexer SELECT signals.

The RAM blocks can be loaded with data generated internally (typically for RAM or FIFO functions) or with

data from an external PROM (typically for ROM functions).

Phase Locked Loops (PLLs)

Instead of requiring extra components, designers simply need to instantiate one of the pre-configured models

described in this section and listed in Table 4. The QuickLogic built-in PLLs support a wider range of

frequencies than many other PLLs. Also, QuickLogic PLLs can be cascaded to support different ranges of

frequency multiplications or divisions, driving the device at a faster or slower rate than the incoming clock

frequency. Most importantly, they achieve a very short clock-to-out time—generally less than 3 ns. This low

clock-to-out time is achieved by the PLL subtracting the clock tree delay through the feedback path, effectively

making the clock tree delay zero.

Figure 5 illustrates a typical QuickLogic ESP PLL.

Figure 5: PLL Block

vco

Filter

FIN

FOUT

1st Quadrant

2nd Quadrant

3rd Quadrant

4th Quadrant

Clock

Tree

Frequency Divide

Frequency Multiply

PLL Bypass

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Fin represents a very stable high-frequency input clock and produces an accurate signal reference. This signal

can either bypass the PLL entirely, thus entering the clock tree directly, or it can pass through the PLL itself.

Within the PLL, a voltage-controlled oscillator (VCO) is added to the circuit. The external Fin signal and the

local VCO form a control loop. The VCO is multiplied or divided down to the reference frequency, so that a

phase detector (the crossed circle in Figure 5) can compare the two signals. If the phases of the external and

local signals are not within the tolerance required, the phase detector sends a signal through the charge pump

and loop filter (Figure 5). The charge pump generates an error voltage to bring the VCO back into alignment

and the loop filter removes any high frequency noise before the error voltage enters the VCO. This new VCO

signal enters the clock tree to drive the chip's circuitry.

Fout represents the clock signal that emerges from the output pad (the output signal PLLPAD_OUT is explained

in Table 5). This clock signal is meaningful only when the PLL is configured for external use; otherwise, it

remains in high Z state, as shown in the post-simulation waveform.

Most QuickLogic products contain four PLLs, one to be used in each quadrant. The PLL presented in

Figure 5 controls the clock tree in the fourth Quadrant of its ESP. As previously mentioned, QuickLogic PLLs

compensate for the additional delay created by the clock tree itself by subtracting the clock tree delay through

the feedback path.

For more specific information on the Phase Locked Loops, refer to Application Note 58 at

http://www.quicklogic.com/images/appnote58.pdf.

PLL Modes of Operation

QuickLogic PLLs have eight modes of operation, based on the input frequency and desired output frequency—

Table 4 indicates the features of each mode.

Table 4: PLL Mode Frequencies

PLL Model Output Frequency Input Frequency Rangea

a. The input frequency can range from 12.5 MHz to 500 MHz, while output frequency ranges from 25 MHz to 250 MHz. When you

add PLLs to your top-level design, be sure that the PLL mode matches your desired input and output frequencies.

Output Frequency Range

PLL_HFb

b. HF stands for high frequency and LF stands for low frequency.

Same as input frequency 66 MHz–150 MHz 66 MHz–150 MHz

PLL_LF Same as input frequency 25 MHz–133 MHz 25 MHz–133 MHz

PLL_MULT2HF 2 × input frequency 50 MHz–125 MHz 100 MHz–250 MHz

PLL_MULT2LF 2 × input frequency 16 MHz–50 MHz 32 MHz–100 MHz

PLL_DIV2HF 1/2 × input frequency 100 MHz–250 MHz 50 MHz–125 MHz

PLL_DIV2LF 1/2 × input frequency 50 MHz–100 MHz 25 MHz–50 MHz

PLL_MULT4 4 × input frequency 16 MHz–40 MHz 64 MHz–160 MHz

PLL_DIV4 1/4 × input frequency 100 MHz–300 MHz 25 MHz–75 MHz

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

PLL Signals

Table 5 summarizes the key signals in QuickLogic PLLs.

NOTE: For PLL AC specifications, contact the factory.

Table 5: PLL Signals

Signal Name Description

PLLCLK_INa

a. Because PLLCLK_IN and PLLRST signals have INPAD, and PLLPAD_OUT has OUTPAD, you do not have to add additional pads

to your design.

Input clock signal

PLLRST Active High Reset If PLLRST is asserted, then CLKNET_OUT and PLLPAD_OUT are reset to 0.

This signal must be asserted and then released in order for the LOCK_DETECT to work.

ONn_OFFCHIP

PLL output This signal selects whether the PLL will drive the internal clock network or be used off-

chip. This is a static signal, not a dynamic signal.

Tied to GND = outgoing signal drives internal gates.

Tied to VCC = outgoing signal used off-chip.

CLKNET_OUT Out to internal gates This signal bypasses the PLL logic before driving the internal gates. Note that

this signal cannot be used in the same quadrant where the PLL signal is used (PLLCLK_OUT).

PLLCLK_OUT Out from PLL to internal gates This signal can drive the internal gates after going through the PLL.

For this to work, ONn_OFFCHIP must be tied to GND.

PLLPAD_OUT Out to off-chip This outgoing signal is used off-chip. For this to work, ONn_OFFCHIP signal must

be tied to VCC.

LOCK_DETECT

Active High Lock detection signal NOTE: For simulation purposes, this signal gets asserted after

10 clock cycles. However, it can take a maximum of 200 clock cycles to sync with the input clock

upon release of the RESET signal.

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

I/O Cell Structure

Eclipse features a variety of distinct I/O pins to maximize performance, functionality, and flexibility with bi-

directional I/O pins and input-only pins. All I/O pins are 2.5 V and 3.3 V tolerant and comply with the specific

I/O standard selected. All dedicated input pins are 2.5 V tolerant and comply with the LVCMOS2 standard.For

single ended I/O standards, VCCIO specifies the input tolerance and the output drive. For voltage referenced

I/O standards (e.g., SSTL), the voltage supplied to the INREF pins in each bank specifies the input switch

point. For example, the VCCIO pins must be tied to a 3.3 V supply to provide 3.3 V compliance. Eclipse can

also support the LVDS and LVPECL I/O standards with the use of external resistors (see Table 6).

As designs become more complex and requirements more stringent, several application-specific I/O standards

have emerged for specific applications. I/O standards for processors, memories, and a variety of bus

applications have become commonplace and a requirement for many systems. In addition, I/O timing has

become a greater issue with specific requirements for setup, hold, clock to out, and switching times. Eclipse

has addressed these new system requirements and now includes a completely new I/O cell which consists of

programmable I/Os as well as a new cell structure consisting of three registers—Input, Output, and Output

Enable (OE).

Eclipse offers banks of programmable I/Os that address many of the bus standards that are popular today. As

shown in Figure 6 each bi-directional I/O pin is associated with an I/O cell which features an input register,

an input buffer, an output register, a three-state output buffer, an output enable register, and 2 two-to-one

output multiplexers.

Table 6: I/O Standards and Applications

I/O

Standard

INREF Reference

Voltage Output Voltage Application

LVTTL n/a 3.3 General Purpose

LVC MO S2 n/a 2.5 General Purpose

PCI n/a 3.3 PCI Bus Applications

GTL+ 1.0 n/a Backplane

SSTL3 1.5 3.3 SDRAM

SSTL2 1.25 2.5 SDRAM

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 6: Eclipse I/O Cell

The bi-directional I/O pin options can be programmed for input, output, or bi-directional operation. As shown

in Figure 6, each bi-directional I/O pin is associated with an I/O cell which features an input register, an input

buffer, an output register, a three-state output buffer, an output enable register, and 2 two-to-one multiplexers.

The select lines of the two-to-one multiplexers are static and must be connected to either VCC or GND.

For input functions, I/O pins can provide combinatorial, registered data, or both options simultaneously to the

logic array. For combinatorial input operation, data is routed from I/O pins through the input buffer to the

array logic. For registered input operation, I/O pins drive the D input of input cell registers, allowing data to

be captured with fast set-up times without consuming internal logic cell resources. The comparator and

multiplexor in the input path allows for native support of I/O standards with reference points offset from

traditional ground.

For output functions, I/O pins can receive combinatorial or registered data from the logic array. For

combinatorial output operation, data is routed from the logic array through a multiplexer to the I/O pin. For

registered output operation, the array logic drives the D input of the output cell register which in turn drives

the I/O pin through a multiplexer. The multiplexer allows either a combinatorial or a registered signal to be

driven to the I/O pin. The addition of an output register will also decrease the Tco. Since the output register

does not need to drive the routing the length of the output path is also reduced.

The three-state output buffer controls the flow of data from the array logic to the I/O pin and allows the I/O

pin to act as an input and/or output. The buffer's output enable can be individually controlled by the logic cell

array or any pin (through the regular routing resources), or it can be bank-controlled through one of the global

networks. The signal can also be either combinatorial or registered. This is identical to that of the flow for the

output cell. For combinatorial control operation data is routed from the logic array through a multiplexer to

the three-state control. The IOCTRL pins can directly drive the OE and CLK signals for all I/O cells within the

same bank.

PAD

OUTPUT ENABLE

OUTPUT

INPUT

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

For registered control operation, the array logic drives the D input of the OE cell register which in turn drives

the three-state control through a multiplexer. The multiplexer allows either a combinatorial or a registered

signal to be driven to the three-state control.

When I/O pins are unused, the OE controls can be permanently disabled, allowing the output cell register to

be used for registered feedback into the logic array.

I/O cell registers are controlled by clock, clock enable, and reset signals, which can come from the regular

routing resources, from one of the global networks, or from two IOCTRL input pins per bank of I/Os. The

CLK and RESET signals share common lines, while the clock enables for each register can be independently

controlled. I/O interface support is programmable on a per bank basis. Figure 7 illustrates the I/O bank

configurations.

Each I/O bank is independent of other I/O banks and each I/O bank has its own VCCIO and INREF supply

inputs. A mixture of different I/O standards can be used on the device; however, there is a limitation as to

which I/O standards can be supported within a given bank. Only standards that share a common VCCIO and

INREF can be shared within the same bank (e.g., PCI and LVTTL).

Figure 7: Multiple I/O Banks

Embedded RAM BlocksPLL PLL

Fabric

Embedded RAM BlocksPLL PLL

VCCIO 0 INREF 0 VCCIO 1 INREF 1

VCCIO 2

INREF 2

VCCIO 3

INREF 3

INREF 4VCCIO 4

INREF 5

VCCIO 5

INREF 6

VCCIO 6

INREF 7

VCCIO 7

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Programmable Slew Rate

Each I/O has programmable slew rate capability. The rate is programmable to one of two slew rates either

fast or slow. The slower rate can be used to reduce ground bounce noise.

Programmable Weak Pull-Down

Programmable weak-pull down resistor is available on each I/O. The I/O Weak Pull-Down eliminates the need

for external pull down resistor for used I/O. The spec for pull-down current is maximum of 150 µA under

worst case condition.

Figure 8: Programmable I/O Weak Pull-Down

I/O Output Logic PA D

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Clock Networks

Global Clocks

There are eight global clock networks in the Eclipse device family. Global clocks can drive logic cell, I/O, and

RAM blocks in the device. Five global clocks have access to a Quad Net (local clock network) connection with

a programmable connection to the register inputs. Global clock pins are 2.5 V, LVCMOS2, compliant.

Figure 9: Global Clock Methodology

Quad Net

CLK Pin

Global Clock Net

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Quad-Net Network

There are five Quad-Net local clock networks in each quadrant for a total of 20 in a device. Each Quad-Net is

local to a quadrant. Before driving the columns clock buffers, the quad-net is driven by the output of a mux

which selects between the CLK input and an internally generated clock source (see Figure 10).

Figure 10: Global Clock Structure Schematic

Dedicated Clock

There is one dedicated clock each device of the Eclipse Family (QL6250, QL6325, QL6500, and QL6600).

This clock connects to the clock input of the Logic Cell and I/O registers, and RAM blocks through a hardwired

connection and is multiplexed with the programmable clock input. The dedicated clock provides a fast global

network with low skew. Users have the ability to select either the dedicated clock or the programmable clock

(Figure 11). The dedicated clock is 2.5 V, LVCMOS2, compliant.

Figure 11: Dedicated Clock Circuitry within Logic Cell

NOTE: For more information on the clocking capabilities of Eclipse FPGAs, refer to the QuickLogic

Application Note 68 at http://www.quicklogic.com/images/appnote68.pdf.

I/O Control and Local Hi-Drives

Each bank of I/Os has two input-only pins that can be programmed to drive the RST, CLK and EN inputs of

I/Os in that bank. These input only pins also serve as high drive inputs to a quadrant. As an I/O control or

high drive, these buffers can be driven by the internal logic. I/O control pins, called IOCTRL in the pin tables,

are 2.5 V, LVCMOS2, compliant.

tPGCK tBGCK

Internally generated clock, or

clock from general routing network

Global Clock

(CLK) Input

Global Clock Network

Global Clock Buffer

Programmable Clock or

General Routing

Dedicated Clock CLK

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Programmable Logic Routing

Eclipse devices are delivered with six types of routing resources as follows: short (sometimes called segmented)

wires, dual wires, quad wires, express wires, distributed networks, and default wires. Short wires span the

length of one logic cell, always in the vertical direction. Dual wires run horizontally and span the length of two

logic cells. Short and dual wires are predominantly used for local connections. Default wires supply VCC and

GND (Logic ‘1’ and Logic ‘0’) to each column of logic cells.

Quad wires have passive link interconnect elements every fourth logic cell. As a result, these wires are typically

used to implement intermediate length or medium fan-out nets.

Express lines run the length of the programmable logic uninterrupted. Each of these lines has a higher

capacitance than a quad, dual, or short wire, but less capacitance than shorter wires connected to run the

length of the device. The resistance is lower because the express wires do not require the use of “pass” links.

Express wires provide higher performance for long routes or high fan-out nets.

Distributed networks are described in the clock/control section. These wires span the programmable logic and

are driven by “column clock” buffers. All clock network pin buffers (Dedicated and Global) are hard wired to

individual sets of column clock buffers.

Global POR (Power-On Reset)

The Eclipse family of devices features a global power-on reset. This reset is hardwired to all registers and resets

them to Logic ‘0’ upon power-up of the device. In QuickLogic devices, the asynchronous Reset input to flip-

flops has priority over the Set input. Therefore, the Global POR resets all flip-flops during power-up. If you

want to set the flip-flops to Logic ‘1’, you must assert the “Set” signal after the Global POR signal has been

deasserted.

Figure 12: Power-On Reset

VCC

Power-on

Reset

QXXXXXXX 0

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Joint Test Access Group (JTAG)

Figure 13: JTAG Block Diagram

Microprocessors and Application Specific Integrated Circuits (ASICs) pose many design challenges, not in the

least of which concerns the accessibility of test points. The Joint Test Access Group (JTAG) formed in response

to this challenge, resulting in IEEE standard 1149.1, the Standard Test Access Port and Boundary Scan

Architecture.

The JTAG boundary scan test methodology allows complete observation and control of the boundary pins of

a JTAG-compatible device through JTAG software. A Test Access Port (TAP) controller works in concert with

the Instruction Register (IR), which allow users to run three required tests along with several user-defined tests.

JTAG tests allow users to reduce system debug time, reuse test platforms and tools, and reuse subsystem tests

for fuller verification of higher level system elements.

The 1149.1 standard requires the following three tests:

•Extest Instruction. The Extest instruction performs a PCB interconnect test. This test places a device into

an external boundary test mode, selecting the boundary scan register to be connected between the TAP's

Test Data In (TDI) and Test Data Out (TDO) pins. Boundary scan cells are preloaded with test patterns (via

the Sample/Preload Instruction), and input boundary cells capture the input data for analysis.

•Sample/Preload Instruction. This instruction allows a device to remain in its functional mode, while

selecting the boundary scan register to be connected between the TDI and TDO pins. For this test, the

boundary scan register can be accessed via a data scan operation, allowing users to sample the functional

data entering and leaving the device.

TCK

TMS

TRSTB

RDI TDO

Instruction Decode

Control Logic

TAp Controller

State Machine

(16 States)

Instruction Register

Boundary-Scan Register

(Data Register)

Mux

Bypass

Mux

Internal

User Defined Data Register

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

•Bypass Instruction. The Bypass instruction allows data to skip a device's boundary scan entirely, so the

data passes through the bypass register. The Bypass instruction allows users to test a device without passing

through other devices. The bypass register is connected between the TDI and TDO pins, allowing serial data

to be transferred through a device without affecting the operation of the device.

JTAG BSDL Support

• BSDL-Boundary Scan Description Language

• Machine-readable data for test equipment to generate testing vectors and software

• BSDL files available for all device/package combinations from QuickLogic

• Extensive industry support available and Automatic Test-vector Generation (ATG)

Security Fuses

There are two security links: one to disable reading logic from the array, and the second to disable JTAG access

to the device. Programming these optional links completely disables access to the device from the outside

world and provides an extra level of design security not possible in SRAM-based FPGAs. The option to

program these fuses is selectable via QuickWorks in the Tools/Options/Device Programming window in

SpDE.

Flexibility Fuse

The flexibility link enables Power-Up loading of the Embedded RAM blocks. If the link is programmed, the

Power Up Loading state machine is activated during power-up of the device. The state machine communicates

with an external EPROM via the JTAG pins to download memory contents into the on-chip RAM. If the link

is not programmed, Power-Up Loading is not enabled and the JTAG pins function as they normally would.

The option to program this bit is selectable via QuickWorks in the Tools/Options/Device Programming

window in SpDE. For more information on Power-Up Loading refer to QuickLogic Application Note 55 at

http://www.quicklogic.com/images/appnote55.pdf.

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

JTAG Pin Descriptions

NOTE: All JTAG inputs are clamped to the VCC rail, not the VCCIO. Therefore, these pins can only be driven

up to VCC + 0.3 V. These input pins are LVCMOS2 compliant only (2.5 V). All JTAG outputs are driven by the

VCC rail, not VCCIO. Therefore, these output pins can only drive up to VCC + 0.3 V. These output pins are

LVCMOS2 compliant only (2.5 V).

Table 7: JTAG Pin Descriptions

Pin Function Description

TDI/RSI Test Data In for JTAG/RAM init.

Serial Data In

Hold HIGH during normal operation. Connects to serial PROM

data in for RAM initialization. Connect to VCC if unused

TRSTB/RRO Active low Reset for JTAG/RAM

init. reset out

Hold LOW during normal operation. Connects to serial PROM

reset for RAM initialization. Connect to GND if unused

TMS Test Mode Select for JTAG Hold HIGH during normal operation. Connect to VCC if not used for

JTAG

TCK Test Clock for JTAG Hold HIGH or LOW during normal operation. Connect to VCC or

ground if not used for JTAG

TDO/RCO Test data out for JTAG/RAM init.

clock out

Connect to serial PROM clock for RAM initialization. Must be left

unconnected if not used for JTAG or RAM initialization

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Electrical Specifications

DC Characteristics

The DC Specifications are provided in Table 8 through Table 12.

Table 8: Absolute Maximum Ratings

Parameter Value Parameter Value

VCC Voltage -0.5 V to 3.6 V DC Input Current ±20 mA

VCCIO Voltage -0.5 V to 4.6 V ESD Pad Protection ±2000 V

INREF Voltage 2.7 V Leaded Package

Storage Temperature -65° C to + 150° C

Input Voltagea

a. All dedicated inputs including the CLK, DEDCLK, PLLIN, PLLRST, and IOCTRL pins, are clamped to the VCC rail, not the VCCIO.

Therefore, these pins can only be driven up to VCC + 0.3 V. These input pins are LVCMOS2 compliant only (2.5 V).

-0.5 V to VCCIO +0.5 V Laminate Package (BGA)

Storage Temperature -55° C to + 125° C

Latch-up Immunity ±100 mA

Table 9: Operating Range

Symbol Parameter Military Industrial Commercial Unit

Min. Max. Min. Max. Min. Max.

VCC Supply Voltage 2.3 2.7 2.3 2.7 2.3 2.7 V

VCCIO I/O Input Tolerance Voltage 2.3 3.6 2.3 3.6 2.3 3.6 V

TA Ambient Temperature -55 -40 85 0 70 °C

TC Case Temperature -125 - - - - °C

KDelay

Factor

-4 Speed Grade 0.42 2.3 0.43 2.16 0.47 2.11 n/a

-5 Speed Grade 0.42 1.92 0.43 1.80 0.46 1.76 n/a

-6 Speed Grade 0.42 1.35 0.43 1.26 0.46 1.23 n/a

-7 Speed Grade 0.42 1.27 0.43 1.19 0.46 1.16 n/a

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

NOTE: If PLLs are not used, the VCCPLL and PLLRST pins may be grounded to the lower ICC for the device.

NOTE: The data provided in Table 12 are JEDEC and PCI Specifications. QuickLogic devices either meet

or exceed these requirements.

NOTE: All dedicated inputs including the CLK, DEDCLK, PLLIN, PLLRST, and IOCTRL pins, are clamped

to the VCC rail, not the VCCIO. Therefore, these pins can only be driven up to VCC + 0.3 V. These input pins

are LVCMOS2 compliant only (2.5 V).

Table 10: DC Characteristics

Symbol Parameter Conditions Min. Max. Unit

III or I/O Input Leakage Current VI = VCCIO or GND -10 10 µA

IOZ 3-State Output Leakage Current VI = VCCIO or GND -10 10 µA

CIInput Capacitancea

a. Capacitance is sample tested only. Clock pins are 12 pF maximum.

--8pF

IOS Output Short Circuit Currentb

b. Only one output at a time. Duration should not exceed 30 seconds.

Vo = GND

Vo = VCC

-15

-180

210

ICC D.C. Supply Currentc

c. For -4/-5/-6/-7 commercial grade devices only. See Table 11 for more details on ICC characteristics.

VI,Vo = VCCIO or GND 0.50 (typ) 2 mA

ICCIO D.C. Supply Current on VCCIO - 0 2 mA

ICCIO(DIF) D.C. Supply Current on VCCIO

for Differential I/O ---mA

IREF D.C. Supply Current on INREF --10 10 µA

IPD Pad Pull-down (programmable) VCCIO = 3.6 V - 150 µA

Table 11: ICC Characteristics

Characteristic Condition Temperature

Commercial Industrial Military

ICC

VCCPLL = GND 2 mA (max) 3 mA (max) 5 mA (max)

VCCPLL = VCC 3.25 mA (max) 5 mA (max) 10 mA (max)

Table 12: DC Input and Output Levels

INREF VIL VIH VOL VOH IOL IOH

VMIN VMAX VMIN VMAX VMIN VMAX VMAX VMIN mA mA

LVTTL n/a n/a -0.3 0.8 2.0 VCCIO + 0.3 0.4 2.4 2.0 -2.0

LVC MO S2 n/a n/a -0.3 0.7 1.7 VCCIO + 0.3 0.7 1.7 2.0 -2.0

GTL+ 0.88 1.12 -0.3 INREF - 0.2 INREF + 0.2 VCCIO + 0.3 0.6 n/a 40 n/a

PCI n/a n/a -0.3 0.3 x VCCIO 0.5 x VCCIO VCCIO + 0.5 0.1 x VCCIO 0.9 x VCCIO 1.5 -0.5

SSTL2 1.15 1.35 -0.3 INREF - 0.18 INREF + 0.18 VCCIO + 0.3 0.74 1.76 7.6 -7.6

SSTL3 1.3 1.7 -0.3 INREF - 0.2 INREF + 0.2 VCCIO + 0.3 1.10 1.90 8-8

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

I/O Characteristics

Figure 14: IOL vs. VOL

Figure 15: IOH vs. VOH

IOL vsVOL

100

120

140

160

180

0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00

Supply voltage (V)

Current (mA)

Vccio = 3.6V

Vccio = 3.3V

Vccio = 3.0V

Vccio = 2.7V

Vccio = 2.5V

Vccio = 2.3V

-120

-100

-80

-60

-40

-20

0.00

0.10

0.30

0.50

0.70

0.90

1.10

1.30

1.50

1.70

1.90

2.10

2.30

2.50

2.70

2.90

3.00

3.10

3.30

3.50

3.60

Supply voltage (V)

Current (mA)

VccI/O = 2.3V

VccI/O = 2.5V

VccI/O = 2.7V

VccI/O = 3.3V

VccI/O = 3.6V

VccI/0 = 3.0V

IOH vsVOH

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

AC Characteristics at VCC = 2.5 V, TA = 25° C (K = 1.00)

The AC Specifications are provided from Table 13 to Table 21. Logic Cell diagrams and waveforms are

provided from Figure 16 to Figure 21.

Figure 16: Eclipse Logic Cell

Table 13: Logic Cells

Symbol Parameter Value

Min. Max.

tPD

Combinatorial Delay of the longest path: time taken by the combinatorial

circuit to output 0.205 ns 1.01 ns

tSU

Setup time: time the synchronous input of the flip flop must be stable before the

active clock edge 0.231 ns -

tHL

Hold time: time the synchronous input of the flip flop must be stable after the

active clock edge 0 ns -

tCO

Clock to out delay: the amount of time taken by the flip flop to output after the

active clock edge. -0.427 ns

tCWHI Clock High Time: required minimum time the clock stays high 0.46 ns -

tCWLO Clock Low Time: required minimum time that the clock stays low 0.46 ns -

tSET

Set Delay: time between when the flip flop is “set” (high) and when the output is

consequently “set” (high) - 0.585 ns

tRESET

Reset Delay: time between when the flip flop is “reset” (low) and when the output

is consequently “reset” (low) -0.658 ns

tSW Set Width: time that the SET signal remains high/low 0.3 ns -

tRW Reset Width: time that the RESET signal remains high/low 0.3 ns -

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 17: Logic Cell Flip Flop

Figure 18: Logic Cell Flip Flop Timings - First Waveform

Figure 19: Logic Cell Flip Flop Timings - Second Waveform

SET

CLK

RESET

SET

RESET

CLK

CWHI

(min) t

CWLO

(min)

RESET

SET

CLK

tSU tHL

tCO

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 20: Eclipse Global Clock Structure

Figure 21: Global Clock Structure Schematic

Table 14: Eclipse Global Clock Tree Delays

Clock Segment Parameter Value

Max. Rise Max. Fall

tPGCK Global clock pin delay to quad net 0.990 ns 1.386 ns

tBGCK Global clock buffer delay (quad net to flip flop) 0.534 ns 1.865 ns

Quad net

Programmable Clock

External Clock

Global Clock Buffer

Global Clock

tPGCK tBGCK

Clock

Select

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 22: RAM Module

Table 15: RAM Cell Synchronous Write Timing

Symbol Parameter Value

Min. Max.

RAM Cell Synchronous Write Timing

tSWA

WA setup time to WCLK: time the WRITE ADDRESS must be stable before the

active edge of the WRITE CLOCK 0.675 ns -

tHWA

WA hold time to WCLK: time the WRITE ADDRESS must be stable after the

active edge of the WRITE CLOCK 0 ns -

tSWD

WD setup time to WCLK: time the WRITE DATA must be stable before the

active edge of the WRITE CLOCK 0.654 ns -

tHWD

WD hold time to WCLK: time the WRITE DATA must be stable after the active

edge of the WRITE CLOCK 0 ns -

tSWE

WE setup time to WCLK: time the WRITE ENABLE must be stable before the

active edge of the WRITE CLOCK 0.276 ns -

tHWE

WE hold time to WCLK: time the WRITE ENABLE must be stable after the

active edge of the WRITE CLOCK 0 ns -

tWCRD

WCLK to RD (WA = RA): time between the active WRITE CLOCK edge and the

time when the data is available at RD - 2.796 ns

WCLK

RCLK

RAM Mod ule

[9:0]

[17:0]

[9:0]

[17:0]

ASYNCRD

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 23: RAM Cell Synchronous Write Timing

Table 16: RAM Cell Synchronous and Asynchronous Read Timing

Symbol Parameter Value

Min. Max.

RAM Cell Synchronous Read Timing

tSRA

RA setup time to RCLK: time the READ ADDRESS must be stable before the

active edge of the READ CLOCK 0.686 ns -

tHRA

RA hold time to RCLK: time the READ ADDRESS must be stable after the active

edge of the READ CLOCK 0 ns -

tSRE

RE setup time to WCLK: time the READ ENABLE must be stable before the active

edge of the READ CLOCK 0.243 ns -

tHRE

RE hold time to WCLK: time the READ ENABLE must be stable after the active

edge of the READ CLOCK 0 ns -

tRCRD

RCLK to RD: time between the active READ CLOCK edge and the time when the

data is available at RD - 2.225 ns

RAM Cell Asynchronous Read Timing

rPDRD

RA to RD: time between when the READ ADDRESS is input and when the DATA

is output - 2.405 ns

tSWA

tSWD

tSWE

tHWA

tHWD

tHWE

tWCRD

old data new data

WCLK

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 24: RAM Cell Synchronous and Asynchronous Read Timing

Figure 25: Eclipse Cell I/O

SRA

HRA

RCLK

SRE

HRE

RCRD

old data new data

PDRD

PAD

OUTPUT ENABLE

OUTPUT

INPUT

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 26: Eclipse Input Register Cell

Table 17: Input Register Cell

Symbol Parameter Value

Min. Max.

tISU

Input register setup time: time the synchronous input of the pin must be stable

before the active clock edge 3.308 ns 3.526 ns

tIHL

Input register hold time: time the synchronous input of the flip-flop must be

stable after the active clock edge 0 ns -

tICO

Input register clock to out: time taken by the flip-flop to output after the active

clock edge - 0.494 ns

tIRST

Input register reset delay: time between when the flip-flop is “reset” (low) and

when the output is consequently “reset” (low) -0.464 ns

tIESU

Input register clock enable setup time: time “enable” must be stable before the

active clock edge 0.830 ns 0.987 ns

tIEH

Input register clock enable hold time: time “enable” must be stable after the

active clock edge 0 ns -

PAD

tIN,t

INI

tICLK

tISU

tSID

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 27: Eclipse Input Register Cell Timing

Table 18: Standard Input Delays

Symbol Parameter Value

To get the total input delay add this delay to tISU Min. Max.

tSID (LVTTL) LVTTL input delay: Low Voltage TTL for 3.3 V applications - 0.34 ns

tSID (LVCMOS2) LVCMOS2 input delay: Low Voltage CMOS for 2.5 V and lower applications -0.42 ns

tSID (GTL+) GTL+ input delay: Gunning Transceiver Logic - 0.68 ns

tSID (SSTL3) SSTL3 input delay: Stub Series Terminated Logic for 3.3 V -0.55 ns

tSID (SSTL2) SSTL2 input delay: Stub Series Terminated Logic for 2.5 V - 0.61 ns

CLK

ISU tIHL

tICO

tIESU tIEH

tIRST

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 28: Eclipse Output Register Cell

Table 19: Eclipse Output Register Cell

Symbol Parameter Value

Output Register Cell Only Min. Max.

tOUTLH Output Delay low to high (90% of H) - 2.594 ns

tOUTHL Output Delay high to low (10% of L) -2.163 ns

tPZH Output Delay tri-state to high (90% of H) - 3.056 ns

tPZL Output Delay tri-state to low (10% of L) -2.709 ns

tPHZ Output Delay high to tri-State - 3.434 ns

tPLZ Output Delay low to tri-State -3.318 ns

tCOP Clock to out delay (does not include clock tree delays) - 2.667 ns (fast slew)

8.999 ns (slow slew)

PAD

OUTPUT

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 29: Eclipse Output Register Cell Timing

NOTE: For tips to minimize ground bounce, refer to Application Note 66 at

http://www.quicklogic.com/images/appnote66.pdf.

Table 20: Output Slew Rates @ VCCIO = 3.3 V

Fast Slew Slow Slew

Rising Edge 2.8 V/ns 1.0 V/ns

Falling Edge 2.86 V/ns 1.0 V/ns

Table 21: Output Slew Rates @ VCCIO = 2.5 V

Fast Slew Slow Slew

Rising Edge 1.7 V/ns 0.6 V/ns

Falling Edge 1.9 V/ns 0.6 V/ns

tOUTLH

tOUTHL

tPZH L

tPZL

tPLZ

tPHZ

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Package Thermal Characteristics

Thermal Resistance Equations:

θJC = (TJ - TC)/P

θJA = (TJ - TA)/P

PMAX = (TJMAX - TAMAX)/ θJA

Parameter Description:

θJC: Junction-to-case thermal resistance

θJA: Junction-to-ambient thermal resistance

TJ: Junction temperature

TA: Ambient temperature

P: Power dissipated by the device while operating

PMAX: The maximum power dissipation for the device

TJMAX: Maximum junction temperature

TAMAX: Maximum ambient temperature

NOTE: Maximum junction temperature (TJMAX) is 150°C. To calculate the maximum power dissipation

for a device package look up θJA from Table 22, pick an appropriate TAMAX and use:

PMAX = (150ºC - TAMAX)/ θJA

Table 22: Package Thermal Characteristics

Package Description θJA (º C/W) @ various flow rates (m/sec) θJC (º C/W)

Count

Package

Type 00.5 12

516 PBGA 20.0 19.0 17.5 16.0 7.0

484 PBGA 28.0 26.0 25.0 23.0 9.0

280 LFBGA 18.5 17.0 15.5 14.0 7.0

208 PQFP 26.0 24.5 23.0 22.0 11.0

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Kv and Kt Graphs

Figure 30: Voltage Factor vs. Supply Voltage

Figure 31: Temperature Factor vs. Operating Temperature

Voltage Factor vs. Supply Voltage

0.9200

0.9400

0.9600

0.9800

1.0000

1.0200

1.0400

1.0600

1.0800

1.1000

2.25 2.3 2.35 2.4 2.45 2.5 2.55 2.6 2.65 2.7 2.75

Supply Voltage (V)

Temperature Factor vs. Operating Temperature

0.85

0.90

0.95

1.00

1.05

1.10

1.15

-60 -40 -20 0 20 40 60 80

Junction Temperature C

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Power vs. Operating Frequency

The basic power equation which best models power consumption is given below:

PTOTAL = 0.350 + f[0.0031 ηLC + 0.0948 ηCKBF + 0.01 ηCLBF+ 0.0263 ηCKLD+ 0.543 ηRAM +

0.20 ηPLL+ 0.0035 ηINP + 0.0257 ηOUTP] (mW)

Where:

ηLC is the total number of logic cells in the design

ηCKBF = # of clock buffers

ηCLBF = # of column clock buffers

ηCKLD = # of loads connected to the column clock buffers

ηRAM = # of RAM blocks

ηPLL = # of PLLs

ηINP is the number of input pins

ηOUTP is the number of output pins

Figure 32 exhibits the power consumption in an Eclipse device. The chip was filled with (300) 8-bit counters

(approximately 76% logic cell utilization).

Figure 32: Power Consumption

Power vs Freq. (Counter_300)

0.5

1.5

2.5

0 20 40 60 80 100 120 140

Frequency (Mhz)

Power (W)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 33 illustrates the theoretical worst-case scenarios for 50%, 70%, and 90% utilizations of the QL6600-

516 package. The resources of the device are divided exactly in half; meaning, for 50% utilization, exactly

50% of the I/Os, Logic Cells, RAM blocks, clock network, etc. are utilized. These situations may never occur

in a real design, but they do provide a very rough quantitative measure of power consumption when talking in

terms of 50% or 70% utilization of an Eclipse device.

Figure 33: Power vs. Frequency (Absolute 50%, 70%, and 90% of the Available Resources on Chip)

To learn more about power consumption, refer to Application Note 60 which is located at

http://www.quicklogic.com/images/appnote60.pdf.

Power vs. Frequency

0 50 100 150 200 250 300

Frequency (Mhz)

50% 70% 90%

Power (mW)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Power-Up Sequencing

Figure 34: Power-Up Requirements/Recommendations

When powering up a device, the VCC/VCCIO rails must take 400 µs or longer to reach the maximum value

(refer to Figure 34).

NOTE: Ramping VCC/VCCIO to the maximum voltage faster than 400 µs can cause the device to behave

improperly.

For users with a limited power budget, keep (VCCIO -VCC)MAX

≤

500 mV when ramping up the power supply.

Voltage

VCCIO

VCC

(VCCIO -VCC)MAX

400 us

VCC

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Pin Descriptions

Table 23 describes the pins/balls of all Eclipse devices.

Table 23: Dedicated Pin Descriptions

Pin Direction Function Description

CLKa

a. All dedicated inputs including the CLK, DEDCLK, PLLIN, PLLRST, and IOCTRL pins, are clamped to the VCC rail, not the VCCIO.

Therefore, these pins can only be driven up to VCC + 0.3 V. These input pins are LVCMOS2 compliant only (2.5 V).

IGlobal clock

network driver

Low skew global clock. This pin provides access to a dedicated,

distributed network capable of driving the CLOCK, SET, RESET, F1, and

A2 inputs to the Logic Cell, READ and WRITE CLOCKS, Read and Write

Enables of the Embedded RAM Blocks, and Output Enables of the I/Os.

I/O(A) I/O Input/Output

The I/O pin is a bi-directional pin, configurable to either an input-only,

output-only, or bi-directional pin. The A inside the parenthesis means that

the I/O is located in Bank A. If an I/O is not used, SpDE (QuickWorks Tool)

provides the option of tying that pin to GND, VCC, or TriState during

programming.

VCC IPower supply

pin Connect to 2.5 V supply.

VCCIO(A) I Input voltage

tolerance pin

This pin provides the flexibility to interface the device with either a 3.3 V

device or a 2.5 V device. The A inside the parenthesis means that VCCIO is

located in BANK A. Every I/O pin in Bank A will be tolerant of VCCIO input

signals and will output VCCIO level signals. This pin must be connected to

either 3.3 V or VCC.

VCCPLLb

b. All PLLOUT output pins are driven by the VCC rail, not the VCCIO rail. These output pins are LVCMOS2 compliant only (2.5 V).

Phase locked

loop power

supply pin

Connect to 2.5 V supply. VCCPLL should be connected to 2.5 V supply if

the PLLs are used. If the PLLs are not used, VCCPLL can be connected to

2.5 V supply or GND. See Table 11 for ICC differences when VCCPLL is

connected to 2.5 V or GND.

GND I Ground pin Connect to ground.

PLLINaI PLL clock input Clock input for PLL.

DEDCLKaIDedicated

clock pin

Low skew global clock. This pin provides access to a dedicated,

distributed clock network capable of driving the CLOCK inputs of all

sequential elements of the device (e.g., RAM and flip-flops).

GNDPLL I Ground pin for

PLL Connect to GND.

INREF(A) I

Differential

reference

voltage

The INREF is the reference voltage pin for GTL+, SSTL2, and STTL3

standards. Follow the recommendations provided in Table 18 for the

appropriate standard. The A inside the parenthesis means that INREF is

located in BANK A. This pin should be tied to GND if not needed.

PLLOUTbO PLL output pin Dedicated PLL output pin. Otherwise may be left unconnected.

PLLRSTaIReset input pin

for PLL

Reset input for PLL. If PLLs are not used, PLLRST should be connected

to the same voltage as VCCPLL (e.g., VCC or GND).

IOCTRL(A)aI Highdrive input

This pin provides fast RESET, SET, CLOCK, and ENABLE access to the

I/O cell flip-flops, providing fast clock-to-out and fast I/O response times.

This pin can also double as a high-drive pin to the internal logic cells. The

A inside the parenthesis means that IOCTRL is located in Bank A. This pin

should be tied to GND or VCC if it is not used.

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

Figure 35: I/O Banks with Relevant Pins

Recommended Unused Pin Terminations for the Eclipse Devices

All unused, general purpose I/O pins can be tied to VCC, GND, or HIZ (high impedance) internally using the

Configuration Editor. This option is given in the bottom-right corner of the placement window. To use the

Placement Editor, choose ConstraintÆFix Placement in the Option pull-down menu of SpDE.

The rest of the pins should be terminated at the board level in the manner presented in Table 24.

NOTE: x -> number, y -> alphabetical character.

Table 24: Recommended Unused Pin Terminations

Signal Name Recommended Termination

PLLOUT<x>

For low power unused PLL output pins can be connected to VCC or GND so that their associated

input buffer never floats, otherwise PLL output pins can be left unconnected. Utilized PLL output

pins that route the PLL clock outside of the chip should not be tied to either VCC or GND.

IOCTRL<y> Any unused pins of this type must be connected to either VCC or GND.

CLK/PLLIN<x> Any unused clock pins should be connected to VCC or GND.

PLLRST<x>

If a PLL module is not used, then the associated PLLRST<x> must be connected to VCC; under

normal operation, use it as needed. If PLLs are not used, the associated PLLRST pin must be

connected to the same voltage as VCCPLL (2.5 V or GND).

INREF<y> If an I/O bank does not require the use of INREF signal the pin should be connected to GND.

IO BANK A IO BANK B

VCCIO(A)

INREF(A)

IOCTRL(A)

IO(A)

VCCIO (A)

INREF(A)

IOCTRL(A)

IO(A)

IO BANK C IO BANK D

VCCIO (C)

INREF(C)

IOCTRL(C)

IO(C)

VCCIO(D)

INREF(D)

IOCTRL(D)

IO(D)

IO BANK F IO BANK E

VCCIO (F)

INREF(F)

IOCTRL(F)

IO(F)

VCCIO(E)

INREF(E)

IOCTRL(E)

IO(E)

IO BANK HIO BANK G

(H)

INREF(H)

IOCTRL(H)

IO(H)

VCCIO

(G)

INREF(G)

IOCTRL(G)

IO(G)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 208 PQFP Pinout Diagram

Eclipse

QL6250-4PQ208C

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 208 PQFP Pinout Table

Table 25: 208 PQFP Pinout Table

Pin Function Pin Function Pin Function Pin Function Pin Function

1PLLRST(3) 43 IO(B) 85 IO(D) 127 CLK(5)/PLLIN(3) 169 IOCTRL(G)

2VCCPLL(3) 44 VCCIO(B) 86 VCC 128 CLK(6) 170 INREF(G)

3GND 45 IO(B) 87 IO(D) 129 VCC 171 IOCTRL(G)

4GND 46 VCC 88 IO(D) 130 CLK(7) 172 IO(G)

5IO(A) 47 IO(B) 89 VCC 131 VCC 173 IO(G)

6IO(A) 48 IO(B) 90 IO(D) 132 CLK(8) 174 IO(G)

7IO(A) 49 GND 91 IO(D) 133 TMS 175 VCC

8VCCIO(A) 50 TDO 92 IOCTRL(D) 134 IO(F) 176 IO(G)

9IO(A) 51 PLLOUT(1) 93 INREF(D) 135 IO(F) 177 VCCIO(G)

10 IO(A) 52 GNDPLL(2) 94 IOCTRL(D) 136 IO(F) 178 GND

11 IOCTRL(A) 53 GND 95 IO(D) 137 GND 179 IO(G)

12 VCC 54 VCCPLL(2) 96 IO(D) 138 VCCIO(F) 180 IO(G)

13 INREF(A) 55 PLLRST(2) 97 IO(D) 139 IO(F) 181 IO(G)

14 IOCTRL(A) 56 VCC 98 VCCIO(D) 140 IO(F) 182 VCC

15 IO(A) 57 IO(C) 99 IO(D) 141 IO(F) 183 TCK

16 IO(A) 58 GND 100 IO(D) 142 IO(F) 184 VCC

17 IO(A) 59 IO(C) 101 GND 143 IO(F) 185 IO(H)

18 IO(A) 60 VCCIO(C) 102 PLLOUT(0) 144 IOCTRL(F) 186 IO(H)

19 VCCIO(A) 61 IO(C) 103 GND 145 INREF(F) 187 IO(H)

20 IO(A) 62 IO(C) 104 GNDPLL(1) 146 VCC 188 GND

21 GND 63 IO(C) 105 PLLRST(1) 147 IOCTRL(F) 189 VCCIO(H)

22 IO(A) 64 IO(C) 106 VCCPLL(1) 148 IO(F) 190 IO(H)

23 TDI 65 IO(C) 107 IO(E) 149 IO(F) 191 IO(H)

24 CLK(0) 66 IO(C) 108 GND 150 VCCIO(F) 192 IOCTRL(H)

25 CLK(1) 67 IOCTRL(C) 109 IO(E) 151 IO(F) 193 IO(H)

26 VCC 68 INREF(C) 110 IO(E) 152 IO(F) 194 INREF(H)

27 CLK(2)/PLLIN(2) 69 IOCTRL(C) 111 VCCIO(E) 153 GND 195 VCC

28 CLK(3)/PLLIN(1) 70 IO(C) 112 IO(E) 154 IO(F) 196 IOCTRL(H)

29 VCC 71 IO(C) 113 VCC 155 PLLOUT(3) 197 IO(H)

30 CLK(4)/

DEDCLK/PLLIN(0) 72 VCCIO(C) 114 IO(E) 156 GNDPLL(0) 198 IO(H)

31 IO(B) 73 IO(C) 115 IO(E) 157 GND 199 IO(H)

32 IO(B) 74 IO(C) 116 IO(E) 158 VCCPLL(0) 200 IO(H)

33 GND 75 GND 117 IOCTRL(E) 159 PLLRST(0) 201 IO(H)

34 VCCIO(B) 76 VCC 118 INREF(E) 160 GND 202 IO(H)

35 IO(B) 77 IO(C) 119 IOCTRL(E) 161 IO(G) 203 VCCIO(H)

36 IO(B) 78 TRSTB 120 IO(E) 162 VCCIO(G) 204 GND

37 IO(B) 79 VCC 121 IO(E) 163 IO(G) 205 IO(H)

38 IO(B) 80 IO(D) 122 VCCIO(E) 164 IO(G) 206 PLLOUT(2)

39 IOCTRL(B) 81 IO(D) 123 GND 165 VCC 207 GND

40 INREF(B) 82 IO(D) 124 IO(E) 166 IO(G) 208 GNDPLL(3)

41 IOCTRL(B) 83 GND 125 IO(E) 167 IO(G)

42 IO(B) 84 VCCIO(D) 126 IO(E) 168 IO(G)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 280 LFBGA Pinout Diagram

Top

Bottom

Eclipse

QL6250-4PT280C

Pin A1

Corner

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 280 LFBGA Pinout Table

Table 26: 280 LFBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 PLLOUT(3) C10 CLK(5)/

PLLIN(3) E19 IOCTRL(D) K16 I/O(C) R4 I/O(H) U13 I/O(B)

A2 GNDPLL(0) C11 VCCIO(E) F1 INREF(G) K17 I/O(D) R5 GND U14 IOCTRL(B)

A3 I/O(F) C12 I/O(E) F2 IOCTRL(G) K18 I/O(C) R6 GND U15 VCCIO(B)

A4 I/O(F) C13 I/O(E) F3 I/O(G) K19 TRSTB R7 VCC U16 I/O(B)

A5 I/O(F) C14 I/O(E) F4 I/O(G) L1 I/O(H) R8 VCC U17 TDO

A6 IOCTRL(F) C15 VCCIO(E) F5 GND L2 I/O(H) R9 GND U18 PLLRST(2)

A7 I/O(F) C16 I/O(E) F15 VCC L3 VCCIO(H) R10 GND U19 I/O(B)

A8 I/O(F) C17 I/O(E) F16 IOCTRL(D) L4 I/O(H) R11 VCC V1 PLLOUT(2)

A9 I/O(F) C18 I/O(E) F17 I/O(D) L5 VCC R12 VCC V2 GNDPLL(3)

A10 CLK(7) C19 I/O(E) F18 I/O(D) L15 GND R13 VCC V3 GND

A11 I/O(E) D1 I/O(G) F19 I/O(D) L16 I/O(C) R14 VCC V4 I/O(A)

A12 I/O(E) D2 I/O(G) G1 I/O(G) L17 VCCIO(C) R15 GND V5 I/O(A)

A13 I/O(E) D3 I/O(F) G2 I/O(G) L18 I/O(C) R16 I/O(C) V6 IOCTRL(A)

A14 IOCTRL(E) D4 I/O(F) G3 IOCTRL(G) L19 I/O(C) R17 VCCIO(C) V7 I/O(A)

A15 I/O(E) D5 I/O(F) G4 I/O(G) M1 I/O(H) R18 I/O(C) V8 I/O(A)

A16 I/O(E) D6 I/O(F) G5 VCC M2 I/O(H) R19 I/O(C) V9 I/O(A)

A17 I/O(E) D7 I/O(F) G15 VCC M3 I/O(H) T1 I/O(H) V10 CLK(1)

A18 PLLRST(1) D8 I/O(F) G16 I/O(D) M4 I/O(H) T2 I/O(H) V11

CLK(4)/

DEDCLK/

PLLIN(0)

A19 GND D9 CLK(8) G17 I/O(D) M5 VCC T3 I/O(A) V12 I/O(B)

B1 PLLRST(0) D10 I/O(E) G18 I/O(D) M15 VCC T4 I/O(A) V13 I/O(B)

B2 GND D11 I/O(E) G19 I/O(D) M16 INREF(C) T5 I/O(A) V14 INREF(B)

B3 I/O(F) D12 I/O(E) H1 I/O(G) M17 I/O(C) T6 IOCTRL(A) V15 I/O(B)

B4 I/O(F) D13 INREF(E) H2 I/O(G) M18 I/O(C) T7 I/O(A) V16 I/O(B)

B5 I/O(F) D14 I/O(E) H3 I/O(G) M19 I/O(C) T8 I/O(A) V17 I/O(B)

B6 INREF(F) D15 I/O(E) H4 I/O(G) N1 IOCTRL(H) T9 I/O(A) V18 GNDPLL(2)

B7 I/O(F) D16 I/O(D) H5 VCC N2 I/O(H) T10 I/O(A) V19 GND

B8 I/O(F) D17 I/O(D) H15 VCC N3 I/O(H) T11 CLK(3)/

PLLIN(1) W1 GND

B9 TMS D18 I/O(D) H16 VCC N4 I/O(H) T12 I/O(B) W2 PLLRST(3)

B10 CLK(6) D19 I/O(D) H17 I/O(D) N5 VCC T13 I/O(B) W3 I/O(A)

B11 I/O(E) E1 I/O(G) H18 I/O(D) N15 VCC T14 I/O(B) W4 I/O(A)

B12 I/O(E) E2 I/O(G) H19 I/O(D) N16 I/O(C) T15 I/O(B) W5 I/O(A)

B13 IOCTRL(E) E3 VCCIO(G) J1 I/O(G) N17 I/O(C) T16 I/O(B) W6 I/O(A)

B14 I/O(E) E4 I/O(F) J2 I/O(G) N18 IOCTRL(C) T17 VCCPLL(2) W7 I/O(A)

B15 I/O(E) E5 GND J3 VCCIO(G) N19 IOCTRL(C) T18 I/O(B) W8 I/O(A)

B16 I/O(E) E6 VCC J4 I/O(G) P1 I/O(H) T19 I/O(B) W9 TDI

B17 VCCPLL(1) E7 VCC J5 GND P2 I/O(H) U1 I/O(A) W10 CLK(2)/

PLLIN(2)

B18 GNDPLL(1) E8 VCC J15 VCC P3 IOCTRL(H) U2 I/O(A) W11 I/O(B)

B19 PLLOUT(0) E9 VCC J16 I/O(C) P4 INREF(H) U3 VCCPLL(3) W12 I/O(B)

C1 I/O(F) E10 GND J17 VCCIO(D) P5 VCC U4 I/O(A) W13 I/O(B)

C2 VCCPLL(0) E11 GND J18 I/O(D) P15 GND U5 VCCIO(A) W14 IOCTRL(B)

C3 I/O(F) E12 VCC J19 I/O(D) P16 I/O(C) U6 INREF(A) W15 I/O(B)

C4 I/O(F) E13 VCC K1 VCC P17 I/O(C) U7 I/O(A) W16 I/O(B)

C5 VCCIO(F) E14 GND K2 TCK P18 I/O(C) U8 I/O(A) W17 I/O(B)

C6 IOCTRL(F) E15 GND K3 I/O(G) P19 I/O(C) U9 VCCIO(A) W18 I/O(B)

C7 I/O(F) E16 I/O(D) K4 I/O(G) R1 I/O(H) U10 CLK(0) W19 PLLOUT(1)

C8 I/O(F) E17 VCCIO(D) K5 GND R2 I/O(H) U11 VCCIO(B)

C9 VCCIO(F) E18 INREF(D) K15 GND R3 VCCIO(H) U12 I/O(B)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 484 PBGA Pinout Diagram

Top

Bottom

Eclipse

QL6250-4PS484C

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

22 21

Pin A1

Corner

Pin A1

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6250 - 484 PBGA Pinout Table

Table 27: 484 PBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 NC C1 NC E1 IOCTRL(A) G1 NC J1 I/O(A) L1

CLK(4)/

DEDCLK/

PLLIN(0)

A2 PLLRST(3) C2 I/O(A) E2 I/O(A) G2 NC J2 I/O(A) L2 CLK(0)

A3 I/O(A) C3 VCCPLL(3) E3 I/O(A) G3 I/O(A) J3 I/O(A) L3 CLK(2)/PLLIN(2)

A4 I/O(A) C4 PLLOUT(2) E4 I/O(A) G4 I/O(A) J4 I/O(A) L4 I/O(A)

A5 I/O(A) C5 I/O(A) E5 NC G5 I/O(A) J5 I/O(A) L5 I/O(A)

A6 NC C6 NC E6 I/O(H) G6 I/O(A) J6 I/O(A) L6 I/O(A)

A7 I/O(H) C7 I/O(H) E7 NC G7 GND J7 I/O(A) L7 GND

A8 IOCTRL(H) C8 NC E8 I/O(H) G8 I/O(H) J8 VCC L8 GND

A9 I/O(H) C9 IOCTRL(H) E9 I/O(H) G9 I/O(H) J9 GND L9 GND

A10 NC C10 NC E10 I/O(H) G10 NC J10 VCC L10 GND

A11 NC C11 I/O(H) E11 VDED2 G11 I/O(G) J11 VCC L11 GND

A12 TCK C12 NC E12 I/O(G) G12 GND J12 GND L12 GND

A13 I/O(G) C13 I/O(G) E13 I/O(G) G13 NC J13 VCC L13 GND

A14 I/O(G) C14 NC E14 NC G14 NC J14 GND L14 VCC

A15 I/O(G) C15 I/O(G) E15 IOCTRL(G) G15 I/O(G) J15 VCC L15 VCC

A16 NC C16 I/O(G) E16 I/O(G) G16 GND J16 I/O(F) L16 CLK(6)

A17 I/O(G) C17 NC E17 INREF(G) G17 VCCIO(F) J17 VCCIO(F) L17 VCCIO(F)

A18 I/O(G) C18 I/O(G) E18 NC G18 I/O(F) J18 I/O(F) L18 I/O(F)

A19 I/O(F) C19 I/O(F) E19 I/O(F) G19 I/O(F) J19 I/O(F) L19 CLK(8)

A20 GND C20 GNDPLL(0) E20 I/O(F) G20 I/O(F) J20 I/O(F) L20 I/O(F)

A21 PLLOUT(3) C21 I/O(F) E21 NC G21 INREF(F) J21 I/O(F) L21 NC

A22 I/O(F) C22 I/O(F) E22 I/O(F) G22 I/O(F) J22 I/O(F) L22 I/O(F)

B1 I/O(A) D1 I/O(A) F1 I/O(A) H1 I/O(A) K1 TDI M1 I/O(B)

B2 GND D2 I/O(A) F2 INREF(A) H2 I/O(A) K2 I/O(A) M2 I/O(B)

B3 GNDPLL(3) D3 I/O(A) F3 NC H3 I/O(A) K3 I/O(A) M3 I/O(B)

B4 GND D4 I/O(A) F4 I/O(A) H4 I/O(A) K4 I/O(A) M4 CLK(3)/PLLIN(1)

B5 I/O(A) D5 I/O(A) F5 I/O(A) H5 IOCTRL(A) K5 I/O(A) M5 NC

B6 I/O(H) D6 I/O(H) F6 VCCIO(A) H6 VCCIO(A) K6 VCCIO(A) M6 VCCIO(B)

B7 I/O(H) D7 NC F7 VCCIO(H) H7 I/O(H) K7 NC M7 CLK(1)

B8 INREF(H) D8 I/O(H) F8 I/O(H) H8 GND K8 VCC M8 VCC

B9 I/O(H) D9 NC F9 VCCIO(H) H9 VCC K9 VCC M9 VCC

B10 I/O(H) D10 I/O(H) F10 I/O(H) H10 VCC K10 GND M10 GND

B11 I/O(H) D11 I/O(H) F11 VCCIO(H) H11 VDED K11 GND M11 GND

B12 NC D12 I/O(G) F12 VCCIO(G) H12 GND K12 GND M12 GND

B13 NC D13 I/O(G) F13 I/O(G) H13 VCC K13 GND M13 GND

B14 NC D14 I/O(G) F14 VCCIO(G) H14 VCC K14 VCC M14 GND

B15 NC D15 IOCTRL(G) F15 NC H15 GND K15 VCC M15 GND

B16 I/O(G) D16 I/O(G) F16 VCCIO(G) H16 I/O(F) K16 NC M16 GND

B17 I/O(G) D17 I/O(G) F17 NC H17 I/O(F) K17 I/O(F) M17 I/O(E)

B18 I/O(G) D18 I/O(F) F18 I/O(F) H18 NC K18 I/O(F) M18 I/O(E)

B19 PLLRST(0) D19 VCCPLL(0) F19 I/O(F) H19 I/O(F) K19 NC M19 I/O(E)

B20 I/O(F) D20 I/O(F) F20 IOCTRL(F) H20 I/O(F) K20 I/O(F) M20 CLK(7)

B21 I/O(F) D21 I/O(F) F21 I/O(F) H21 I/O(F) K21 I/O(F) M21 CLK(5)/PLLIN(3)

B22 I/O(F) D22 I/O(F) F22 IOCTRL(F) H22 NC K22 NC M22 TMS

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

N1 NC P16 I/O(E) T9 NC V2 I/O(B) W17 NC AA10 I/O(C)

N2 I/O(B) P17 NC T10 TRSTB V3 I/O(B) W18 I/O(E) AA11 I/O(C)

N3 I/O(B) P18 I/O(E) T11 GND V4 I/O(B) W19 NC AA12 I/O(D)

N4 NC P19 NC T12 NC V5 I/O(B) W20 I/O(E) AA13 I/O(D)

N5 I/O(B) P20 I/O(E) T13 I/O(D) V6 NC W21 NC AA14 I/O(D)

N6 NC P21 I/O(E) T14 NC V7 I/O(C) W22 I/O(E) AA15 I/O(D)

N7 NC P22 I/O(E) T15 I/O(D) V8 I/O(C) Y1 I/O(B) AA16 NC

N8 VCC R1 I/O(B) T16 GND V9 NC Y2 I/O(B) AA17 NC

N9 VCC R2 INREF(B) T17 I/O(E) V10 I/O(C) Y3 VCCPLL(2) AA18 I/O(D)

N10 GND R3 I/O(B) T18 I/O(E) V11 NC Y4 I/O(C) AA19 I/O(E)

N11 GND R4 I/O(B) T19 NC V12 VDED2 Y5 I/O(C) AA20 GNDPLL(1)

N12 GND R5 I/O(B) T20 NC V13 NC Y6 I/O(C) AA21 I/O(E)

N13 GND R6 NC T21 IOCTRL(E) V14 I/O(D) Y7 I/O(C) AA22 I/O(E)

N14 VCC R7 I/O(B) T22 I/O(E) V15 I/O(D) Y8 IOCTRL(C) AB1 I/O(B)

N15 VCC R8 GND U1 IOCTRL(B) V16 INREF(D) Y9 I/O(C) AB2 GNDPLL(2)

N16 I/O(E) R9 VCC U2 I/O(B) V17 I/O(D) Y10 I/O(C) AB3 PLLRST(2)

N17 VCCIO(E) R10 VCC U3 IOCTRL(B) V18 I/O(E) Y11 I/O(D) AB4 I/O(B)

N18 I/O(E) R11 GND U4 I/O(B) V19 I/O(E) Y12 NC AB5 I/O(B)

N19 I/O(E) R12 VDED U5 I/O(B) V20 I/O(E) Y13 NC AB6 I/O(C)

N20 I/O(E) R13 VCC U6 I/O(C) V21 I/O(E) Y14 I/O(D) AB7 I/O(C)

N21 I/O(E) R14 VCC U7 VCCIO(C) V22 I/O(E) Y15 IOCTRL(D) AB8 IOCTRL(C)

N22 I/O(E) R15 GND U8 NC W1 I/O(B) Y16 I/O(D) AB9 I/O(C)

P1 NC R16 I/O(D) U9 VCCIO(C) W2 I/O(B) Y17 I/O(D) AB10 I/O(C)

P2 I/O(B) R17 VCCIO(E) U10 I/O(C) W3 I/O(B) Y18 I/O(E) AB11 NC

P3 I/O(B) R18 I/O(E) U11 VCCIO(C) W4 I/O(B) Y19 PLLOUT(0) AB12 I/O(D)

P4 I/O(B) R19 I/O(E) U12 VCCIO(D) W5 I/O(B) Y20 PLLRST(1) AB13 I/O(D)

P5 I/O(B) R20 I/O(E) U13 I/O(D) W6 I/O(C) Y21 I/O(E) AB14 NC

P6 VCCIO(B) R21 I/O(E) U14 VCCIO(D) W7 NC Y22 I/O(E) AB15 I/O(D)

P7 I/O(B) R22 I/O(E) U15 NC W8 NC AA1 TDO AB16 IOCTRL(D)

P8 VCC T1 I/O(B) U16 VCCIO(D) W9 NC AA2 PLLOUT(1) AB17 I/O(D)

P9 GND T2 I/O(B) U17 VCCIO(E) W10 NC AA3 GND AB18 I/O(D)

P10 VCC T3 I/O(B) U18 I/O(E) W11 I/O(C) AA4 I/O(B) AB19 I/O(E)

P11 GND T4 I/O(B) U19 I/O(E) W12 NC AA5 I/O(C) AB20 GND

P12 VCC T5 I/O(B) U20 IOCTRL(E) W13 I/O(D) AA6 I/O(C) AB21 VCCPLL(1)

P13 VCC T6 VCCIO(B) U21 NC W14 NC AA7 NC AB22 I/O(E)

P14 GND T7 GND U22 INREF(E) W15 I/O(D) AA8 INREF(C)

P15 VDED T8 I/O(C) V1 I/O(B) W16 NC AA9 NC

Table 27: 484 PBGA Pinout Table (Continued)

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 208 PQFP Pinout Diagram

Eclipse

QL6325-4PQ208C

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 208 PQFP Pinout Table

Table 28: 208 PQFP Pinout Table

Pin Function Pin Function Pin Function Pin Function Pin Function

1PLLRST(3) 43 IO(B) 85 IO(D) 127 CLK(5)/PLLIN(3) 169 IOCTRL(G)

2VCCPLL(3) 44 VCCIO(B) 86 VCC 128 CLK(6) 170 INREF(G)

3GND 45 IO(B) 87 IO(D) 129 VCC 171 IOCTRL(G)

4GND 46 VCC 88 IO(D) 130 CLK(7) 172 IO(G)

5IO(A) 47 IO(B) 89 VCC 131 VCC 173 IO(G)

6IO(A) 48 IO(B) 90 IO(D) 132 CLK(8) 174 IO(G)

7IO(A) 49 GND 91 IO(D) 133 TMS 175 VCC

8VCCIO(A) 50 TDO 92 IOCTRL(D) 134 IO(F) 176 IO(G)

9IO(A) 51 PLLOUT(1) 93 INREF(D) 135 IO(F) 177 VCCIO(G)

10 IO(A) 52 GNDPLL(2) 94 IOCTRL(D) 136 IO(F) 178 GND

11 IOCTRL(A) 53 GND 95 IO(D) 137 GND 179 IO(G)

12 VCC 54 VCCPLL(2) 96 IO(D) 138 VCCIO(F) 180 IO(G)

13 INREF(A) 55 PLLRST(2) 97 IO(D) 139 IO(F) 181 IO(G)

14 IOCTRL(A) 56 VCC 98 VCCIO(D) 140 IO(F) 182 VCC

15 IO(A) 57 IO(C) 99 IO(D) 141 IO(F) 183 TCK

16 IO(A) 58 GND 100 IO(D) 142 IO(F) 184 VCC

17 IO(A) 59 IO(C) 101 GND 143 IO(F) 185 IO(H)

18 IO(A) 60 VCCIO(C) 102 PLLOUT(0) 144 IOCTRL(F) 186 IO(H)

19 VCCIO(A) 61 IO(C) 103 GND 145 INREF(F) 187 IO(H)

20 IO(A) 62 IO(C) 104 GNDPLL(1) 146 VCC 188 GND

21 GND 63 IO(C) 105 PLLRST(1) 147 IOCTRL(F) 189 VCCIO(H)

22 IO(A) 64 IO(C) 106 VCCPLL(1) 148 IO(F) 190 IO(H)

23 TDI 65 IO(C) 107 IO(E) 149 IO(F) 191 IO(H)

24 CLK(0) 66 IO(C) 108 GND 150 VCCIO(F) 192 IOCTRL(H)

25 CLK(1) 67 IOCTRL(C) 109 IO(E) 151 IO(F) 193 IO(H)

26 VCC 68 INREF(C) 110 IO(E) 152 IO(F) 194 INREF(H)

27 CLK(2)/PLLIN(2) 69 IOCTRL(C) 111 VCCIO(E) 153 GND 195 VCC

28 CLK(3)/PLLIN(1) 70 IO(C) 112 IO(E) 154 IO(F) 196 IOCTRL(H)

29 VCC 71 IO(C) 113 VCC 155 PLLOUT(3) 197 IO(H)

30 CLK(4)/

DEDCLK/PLLIN(0) 72 VCCIO(C) 114 IO(E) 156 GNDPLL(0) 198 IO(H)

31 IO(B) 73 IO(C) 115 IO(E) 157 GND 199 IO(H)

32 IO(B) 74 IO(C) 116 IO(E) 158 VCCPLL(0) 200 IO(H)

33 GND 75 GND 117 IOCTRL(E) 159 PLLRST(0) 201 IO(H)

34 VCCIO(B) 76 VCC 118 INREF(E) 160 GND 202 IO(H)

35 IO(B) 77 IO(C) 119 IOCTRL(E) 161 IO(G) 203 VCCIO(H)

36 IO(B) 78 TRSTB 120 IO(E) 162 VCCIO(G) 204 GND

37 IO(B) 79 VCC 121 IO(E) 163 IO(G) 205 IO(H)

38 IO(B) 80 IO(D) 122 VCCIO(E) 164 IO(G) 206 PLLOUT(2)

39 IOCTRL(B) 81 IO(D) 123 GND 165 VCC 207 GND

40 INREF(B) 82 IO(D) 124 IO(E) 166 IO(G) 208 GNDPLL(3)

41 IOCTRL(B) 83 GND 125 IO(E) 167 IO(G)

42 IO(B) 84 VCCIO(D) 126 IO(E) 168 IO(G)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 280 LFBGA Pinout Diagram

Top

Bottom

Eclipse

QL6325-4PT280C

Pin A1

Corner

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 280 LFBGA Pinout Table

Table 29: 280 LFBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 PLLOUT(3) C10 CLK(5)/

PLLIN(3) E19 IOCTRL(D) K16 I/O(C) R4 I/O(H) U13 I/O(B)

A2 GNDPLL(0) C11 VCCIO(E) F1 INREF(G) K17 I/O(D) R5 GND U14 IOCTRL(B)

A3 I/O(F) C12 I/O(E) F2 IOCTRL(G) K18 I/O(C) R6 GND U15 VCCIO(B)

A4 I/O(F) C13 I/O(E) F3 I/O(G) K19 TRSTB R7 VCC U16 I/O(B)

A5 I/O(F) C14 I/O(E) F4 I/O(G) L1 I/O(H) R8 VCC U17 TDO

A6 IOCTRL(F) C15 VCCIO(E) F5 GND L2 I/O(H) R9 GND U18 PLLRST(2)

A7 I/O(F) C16 I/O(E) F15 VCC L3 VCCIO(H) R10 GND U19 I/O(B)

A8 I/O(F) C17 I/O(E) F16 IOCTRL(D) L4 I/O(H) R11 VCC V1 PLLOUT(2)

A9 I/O(F) C18 I/O(E) F17 I/O(D) L5 VCC R12 VCC V2 GNDPLL(3)

A10 CLK(7) C19 I/O(E) F18 I/O(D) L15 GND R13 VCC V3 GND

A11 I/O(E) D1 I/O(G) F19 I/O(D) L16 I/O(C) R14 VCC V4 I/O(A)

A12 I/O(E) D2 I/O(G) G1 I/O(G) L17 VCCIO(C) R15 GND V5 I/O(A)

A13 I/O(E) D3 I/O(F) G2 I/O(G) L18 I/O(C) R16 I/O(C) V6 IOCTRL(A)

A14 IOCTRL(E) D4 I/O(F) G3 IOCTRL(G) L19 I/O(C) R17 VCCIO(C) V7 I/O(A)

A15 I/O(E) D5 I/O(F) G4 I/O(G) M1 I/O(H) R18 I/O(C) V8 I/O(A)

A16 I/O(E) D6 I/O(F) G5 VCC M2 I/O(H) R19 I/O(C) V9 I/O(A)

A17 I/O(E) D7 I/O(F) G15 VCC M3 I/O(H) T1 I/O(H) V10 CLK(1)

A18 PLLRST(1) D8 I/O(F) G16 I/O(D) M4 I/O(H) T2 I/O(H) V11

CLK(4)/

DEDCLK/

PLLIN(0)

A19 GND D9 CLK(8) G17 I/O(D) M5 VCC T3 I/O(A) V12 I/O(B)

B1 PLLRST(0) D10 I/O(E) G18 I/O(D) M15 VCC T4 I/O(A) V13 I/O(B)

B2 GND D11 I/O(E) G19 I/O(D) M16 INREF(C) T5 I/O(A) V14 INREF(B)

B3 I/O(F) D12 I/O(E) H1 I/O(G) M17 I/O(C) T6 IOCTRL(A) V15 I/O(B)

B4 I/O(F) D13 INREF(E) H2 I/O(G) M18 I/O(C) T7 I/O(A) V16 I/O(B)

B5 I/O(F) D14 I/O(E) H3 I/O(G) M19 I/O(C) T8 I/O(A) V17 I/O(B)

B6 INREF(F) D15 I/O(E) H4 I/O(G) N1 IOCTRL(H) T9 I/O(A) V18 GNDPLL(2)

B7 I/O(F) D16 I/O(D) H5 VCC N2 I/O(H) T10 I/O(A) V19 GND

B8 I/O(F) D17 I/O(D) H15 VCC N3 I/O(H) T11 CLK(3)/

PLLIN(1) W1 GND

B9 TMS D18 I/O(D) H16 VCC N4 I/O(H) T12 I/O(B) W2 PLLRST(3)

B10 CLK(6) D19 I/O(D) H17 I/O(D) N5 VCC T13 I/O(B) W3 I/O(A)

B11 I/O(E) E1 I/O(G) H18 I/O(D) N15 VCC T14 I/O(B) W4 I/O(A)

B12 I/O(E) E2 I/O(G) H19 I/O(D) N16 I/O(C) T15 I/O(B) W5 I/O(A)

B13 IOCTRL(E) E3 VCCIO(G) J1 I/O(G) N17 I/O(C) T16 I/O(B) W6 I/O(A)

B14 I/O(E) E4 I/O(F) J2 I/O(G) N18 IOCTRL(C) T17 VCCPLL(2) W7 I/O(A)

B15 I/O(E) E5 GND J3 VCCIO(G) N19 IOCTRL(C) T18 I/O(B) W8 I/O(A)

B16 I/O(E) E6 VCC J4 I/O(G) P1 I/O(H) T19 I/O(B) W9 TDI

B17 VCCPLL(1) E7 VCC J5 GND P2 I/O(H) U1 I/O(A) W10 CLK(2)/

PLLIN(2)

B18 GNDPLL(1) E8 VCC J15 VCC P3 IOCTRL(H) U2 I/O(A) W11 I/O(B)

B19 PLLOUT(0) E9 VCC J16 I/O(C) P4 INREF(H) U3 VCCPLL(3) W12 I/O(B)

C1 I/O(F) E10 GND J17 VCCIO(D) P5 VCC U4 I/O(A) W13 I/O(B)

C2 VCCPLL(0) E11 GND J18 I/O(D) P15 GND U5 VCCIO(A) W14 IOCTRL(B)

C3 I/O(F) E12 VCC J19 I/O(D) P16 I/O(C) U6 INREF(A) W15 I/O(B)

C4 I/O(F) E13 VCC K1 VCC P17 I/O(C) U7 I/O(A) W16 I/O(B)

C5 VCCIO(F) E14 GND K2 TCK P18 I/O(C) U8 I/O(A) W17 I/O(B)

C6 IOCTRL(F) E15 GND K3 I/O(G) P19 I/O(C) U9 VCCIO(A) W18 I/O(B)

C7 I/O(F) E16 I/O(D) K4 I/O(G) R1 I/O(H) U10 CLK(0) W19 PLLOUT(1)

C8 I/O(F) E17 VCCIO(D) K5 GND R2 I/O(H) U11 VCCIO(B)

C9 VCCIO(F) E18 INREF(D) K15 GND R3 VCCIO(H) U12 I/O(B)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 484 PBGA Pinout Diagram

Top

Bottom

Eclipse

QL6325-4PS484C

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

22 21

Pin A1

Corner

Pin A1

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6325 - 484 PBGA Pinout Table

Table 30: 484 PBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 I/O(A) C1 I/O(A) E1 IOCTRL(A) G1 I/O(A) J1 I/O(A) L1

CLK(4)/

DEDCLK/

PLLIN(0)

A2 PLLRST(3) C2 I/O(A) E2 I/O(A) G2 I/O(A) J2 I/O(A) L2 CLK(0)

A3 I/O(A) C3 VCCPLL(3) E3 I/O(A) G3 I/O(A) J3 I/O(A) L3 CLK(2)/PLLIN(2)

A4 I/O(A) C4 PLLOUT(2) E4 I/O(A) G4 I/O(A) J4 I/O(A) L4 I/O(A)

A5 I/O(A) C5 I/O(A) E5 I/O(A) G5 I/O(A) J5 I/O(A) L5 I/O(A)

A6 I/O(H) C6 I/O(H) E6 I/O(H) G6 I/O(A) J6 I/O(A) L6 I/O(A)

A7 I/O(H) C7 I/O(H) E7 NC G7 GND J7 I/O(A) L7 GND

A8 IOCTRL(H) C8 I/O(H) E8 I/O(H) G8 I/O(H) J8 VCC L8 GND

A9 I/O(H) C9 IOCTRL(H) E9 I/O(H) G9 I/O(H) J9 GND L9 GND

A10 NC C10 I/O(H) E10 I/O(H) G10 I/O(H) J10 VCC L10 GND

A11 NC C11 I/O(H) E11 VDED2 G11 I/O(G) J11 VCC L11 GND

A12 TCK C12 I/O(H) E12 I/O(G) G12 GND J12 GND L12 GND

A13 I/O(G) C13 I/O(G) E13 I/O(G) G13 I/O(G) J13 VCC L13 GND

A14 I/O(G) C14 I/O(G) E14 I/O(G) G14 I/O(G) J14 GND L14 VCC

A15 I/O(G) C15 I/O(G) E15 IOCTRL(G) G15 I/O(G) J15 VCC L15 VCC

A16 I/O(G) C16 I/O(G) E16 I/O(G) G16 GND J16 I/O(F) L16 CLK(6)

A17 I/O(G) C17 I/O(G) E17 INREF(G) G17 VCCIO(F) J17 VCCIO(F) L17 VCCIO(F)

A18 I/O(G) C18 I/O(G) E18 I/O(G) G18 I/O(F) J18 I/O(F) L18 I/O(F)

A19 I/O(F) C19 I/O(F) E19 I/O(F) G19 I/O(F) J19 I/O(F) L19 CLK(8)

A20 GND C20 GNDPLL(0) E20 I/O(F) G20 I/O(F) J20 I/O(F) L20 I/O(F)

A21 PLLOUT(3) C21 I/O(F) E21 I/O(F) G21 INREF(F) J21 I/O(F) L21 I/O(F)

A22 I/O(F) C22 I/O(F) E22 I/O(F) G22 I/O(F) J22 I/O(F) L22 I/O(F)

B1 I/O(A) D1 I/O(A) F1 I/O(A) H1 I/O(A) K1 TDI M1 I/O(B)

B2 GND D2 I/O(A) F2 INREF(A) H2 I/O(A) K2 I/O(A) M2 I/O(B)

B3 GNDPLL(3) D3 I/O(A) F3 I/O(A) H3 I/O(A) K3 I/O(A) M3 I/O(B)

B4 GND D4 I/O(A) F4 I/O(A) H4 I/O(A) K4 I/O(A) M4 CLK(3)/PLLIN(1)

B5 I/O(A) D5 I/O(A) F5 I/O(A) H5 IOCTRL(A) K5 I/O(A) M5 I/O(B)

B6 I/O(H) D6 I/O(H) F6 VCCIO(A) H6 VCCIO(A) K6 VCCIO(A) M6 VCCIO(B)

B7 I/O(H) D7 I/O(H) F7 VCCIO(H) H7 I/O(H) K7 I/O(A) M7 CLK(1)

B8 INREF(H) D8 I/O(H) F8 I/O(H) H8 GND K8 VCC M8 VCC

B9 I/O(H) D9 I/O(H) F9 VCCIO(H) H9 VCC K9 VCC M9 VCC

B10 I/O(H) D10 I/O(H) F10 I/O(H) H10 VCC K10 GND M10 GND

B11 I/O(H) D11 I/O(H) F11 VCCIO(H) H11 VDED K11 GND M11 GND

B12 NC D12 I/O(G) F12 VCCIO(G) H12 GND K12 GND M12 GND

B13 NC D13 I/O(G) F13 I/O(G) H13 VCC K13 GND M13 GND

B14 NC D14 I/O(G) F14 VCCIO(G) H14 VCC K14 VCC M14 GND

B15 I/O(G) D15 IOCTRL(G) F15 NC H15 GND K15 VCC M15 GND

B16 I/O(G) D16 I/O(G) F16 VCCIO(G) H16 I/O(F) K16 I/O(F) M16 GND

B17 I/O(G) D17 I/O(G) F17 NC H17 I/O(F) K17 I/O(F) M17 I/O(E)

B18 I/O(G) D18 I/O(F) F18 I/O(F) H18 I/O(F) K18 I/O(F) M18 I/O(E)

B19 PLLRST(0) D19 VCCPLL(0) F19 I/O(F) H19 I/O(F) K19 I/O(F) M19 I/O(E)

B20 I/O(F) D20 I/O(F) F20 IOCTRL(F) H20 I/O(F) K20 I/O(F) M20 CLK(7)

B21 I/O(F) D21 I/O(F) F21 I/O(F) H21 I/O(F) K21 I/O(F) M21 CLK(5)/PLLIN(3)

B22 I/O(F) D22 I/O(F) F22 IOCTRL(F) H22 I/O(F) K22 I/O(F) M22 TMS

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

N1 I/O(B) P16 I/O(E) T9 NC V2 I/O(B) W17 I/O(D) AA10 I/O(C)

N2 I/O(B) P17 I/O(E) T10 TRSTB V3 I/O(B) W18 I/O(E) AA11 I/O(C)

N3 I/O(B) P18 I/O(E) T11 GND V4 I/O(B) W19 I/O(E) AA12 I/O(D)

N4 I/O(B) P19 I/O(E) T12 NC V5 I/O(B) W20 I/O(E) AA13 I/O(D)

N5 I/O(B) P20 I/O(E) T13 I/O(D) V6 I/O(C) W21 I/O(E) AA14 I/O(D)

N6 I/O(B) P21 I/O(E) T14 NC V7 I/O(C) W22 I/O(E) AA15 I/O(D)

N7 I/O(B) P22 I/O(E) T15 I/O(D) V8 I/O(C) Y1 I/O(B) AA16 I/O(D)

N8 VCC R1 I/O(B) T16 GND V9 NC Y2 I/O(B) AA17 I/O(D)

N9 VCC R2 INREF(B) T17 I/O(E) V10 I/O(C) Y3 VCCPLL(2) AA18 I/O(D)

N10 GND R3 I/O(B) T18 I/O(E) V11 I/O(C) Y4 I/O(C) AA19 I/O(E)

N11 GND R4 I/O(B) T19 I/O(E) V12 VDED2 Y5 I/O(C) AA20 GNDPLL(1)

N12 GND R5 I/O(B) T20 I/O(E) V13 NC Y6 I/O(C) AA21 I/O(E)

N13 GND R6 I/O(B) T21 IOCTRL(E) V14 I/O(D) Y7 I/O(C) AA22 I/O(E)

N14 VCC R7 I/O(B) T22 I/O(E) V15 I/O(D) Y8 IOCTRL(C) AB1 I/O(B)

N15 VCC R8 GND U1 IOCTRL(B) V16 INREF(D) Y9 I/O(C) AB2 GNDPLL(2)

N16 I/O(E) R9 VCC U2 I/O(B) V17 I/O(D) Y10 I/O(C) AB3 PLLRST(2)

N17 VCCIO(E) R10 VCC U3 IOCTRL(B) V18 I/O(E) Y11 I/O(D) AB4 I/O(B)

N18 I/O(E) R11 GND U4 I/O(B) V19 I/O(E) Y12 I/O(D) AB5 I/O(B)

N19 I/O(E) R12 VDED U5 I/O(B) V20 I/O(E) Y13 I/O(D) AB6 I/O(C)

N20 I/O(E) R13 VCC U6 I/O(C) V21 I/O(E) Y14 I/O(D) AB7 I/O(C)

N21 I/O(E) R14 VCC U7 VCCIO(C) V22 I/O(E) Y15 IOCTRL(D) AB8 IOCTRL(C)

N22 I/O(E) R15 GND U8 NC W1 I/O(B) Y16 I/O(D) AB9 I/O(C)

P1 I/O(B) R16 I/O(D) U9 VCCIO(C) W2 I/O(B) Y17 I/O(D) AB10 I/O(C)

P2 I/O(B) R17 VCCIO(E) U10 I/O(C) W3 I/O(B) Y18 I/O(E) AB11 I/O(C)

P3 I/O(B) R18 I/O(E) U11 VCCIO(C) W4 I/O(B) Y19 PLLOUT(0) AB12 I/O(D)

P4 I/O(B) R19 I/O(E) U12 VCCIO(D) W5 I/O(B) Y20 PLLRST(1) AB13 I/O(D)

P5 I/O(B) R20 I/O(E) U13 I/O(D) W6 I/O(C) Y21 I/O(E) AB14 I/O(D)

P6 VCCIO(B) R21 I/O(E) U14 VCCIO(D) W7 NC Y22 I/O(E) AB15 I/O(D)

P7 I/O(B) R22 I/O(E) U15 NC W8 I/O(C) AA1 TDO AB16 IOCTRL(D)

P8 VCC T1 I/O(B) U16 VCCIO(D) W9 I/O(C) AA2 PLLOUT(1) AB17 I/O(D)

P9 GND T2 I/O(B) U17 VCCIO(E) W10 I/O(C) AA3 GND AB18 I/O(D)

P10 VCC T3 I/O(B) U18 I/O(E) W11 I/O(C) AA4 I/O(B) AB19 I/O(E)

P11 GND T4 I/O(B) U19 I/O(E) W12 I/O(D) AA5 I/O(C) AB20 GND

P12 VCC T5 I/O(B) U20 IOCTRL(E) W13 I/O(D) AA6 I/O(C) AB21 VCCPLL(1)

P13 VCC T6 VCCIO(B) U21 I/O(E) W14 I/O(D) AA7 I/O(C) AB22 I/O(E)

P14 GND T7 GND U22 INREF(E) W15 I/O(D) AA8 INREF(C)

P15 VDED T8 I/O(C) V1 I/O(B) W16 NC AA9 I/O(C)

Table 30: 484 PBGA Pinout Table (Continued)

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6500 - 280 LFBGA Pinout Diagram

Top

Bottom

Eclipse

QL6500-4PT280C

Pin A1

Corner

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6500 - 280 LFBGA Pinout Table

Table 31: 280 LFBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 PLLOUT(3) C10 CLK(5)/

PLLIN(3) E19 IOCTRL(D) K16 I/O(C) R4 I/O(H) U13 I/O(B)

A2 GNDPLL(0) C11 VCCIO(E) F1 INREF(G) K17 I/O(D) R5 GND U14 IOCTRL(B)

A3 I/O(F) C12 I/O(E) F2 IOCTRL(G) K18 I/O(C) R6 GND U15 VCCIO(B)

A4 I/O(F) C13 I/O(E) F3 I/O(G) K19 TRSTB R7 VCC U16 I/O(B)

A5 I/O(F) C14 I/O(E) F4 I/O(G) L1 I/O(H) R8 VCC U17 TDO

A6 IOCTRL(F) C15 VCCIO(E) F5 GND L2 I/O(H) R9 GND U18 PLLRST(2)

A7 I/O(F) C16 I/O(E) F15 VCC L3 VCCIO(H) R10 GND U19 I/O(B)

A8 I/O(F) C17 I/O(E) F16 IOCTRL(D) L4 I/O(H) R11 VCC V1 PLLOUT(2)

A9 I/O(F) C18 I/O(E) F17 I/O(D) L5 VCC R12 VCC V2 GNDPLL(3)

A10 CLK(7) C19 I/O(E) F18 I/O(D) L15 GND R13 VCC V3 GND

A11 I/O(E) D1 I/O(G) F19 I/O(D) L16 I/O(C) R14 VCC V4 I/O(A)

A12 I/O(E) D2 I/O(G) G1 I/O(G) L17 VCCIO(C) R15 GND V5 I/O(A)

A13 I/O(E) D3 I/O(F) G2 I/O(G) L18 I/O(C) R16 I/O(C) V6 IOCTRL(A)

A14 IOCTRL(E) D4 I/O(F) G3 IOCTRL(G) L19 I/O(C) R17 VCCIO(C) V7 I/O(A)

A15 I/O(E) D5 I/O(F) G4 I/O(G) M1 I/O(H) R18 I/O(C) V8 I/O(A)

A16 I/O(E) D6 I/O(F) G5 VCC M2 I/O(H) R19 I/O(C) V9 I/O(A)

A17 I/O(E) D7 I/O(F) G15 VCC M3 I/O(H) T1 I/O(H) V10 CLK(1)

A18 PLLRST(1) D8 I/O(F) G16 I/O(D) M4 I/O(H) T2 I/O(H) V11

CLK(4)/

DEDCLK/

PLLIN(0)

A19 GND D9 CLK(8) G17 I/O(D) M5 VCC T3 I/O(A) V12 I/O(B)

B1 PLLRST(0) D10 I/O(E) G18 I/O(D) M15 VCC T4 I/O(A) V13 I/O(B)

B2 GND D11 I/O(E) G19 I/O(D) M16 INREF(C) T5 I/O(A) V14 INREF(B)

B3 I/O(F) D12 I/O(E) H1 I/O(G) M17 I/O(C) T6 IOCTRL(A) V15 I/O(B)

B4 I/O(F) D13 INREF(E) H2 I/O(G) M18 I/O(C) T7 I/O(A) V16 I/O(B)

B5 I/O(F) D14 I/O(E) H3 I/O(G) M19 I/O(C) T8 I/O(A) V17 I/O(B)

B6 INREF(F) D15 I/O(E) H4 I/O(G) N1 IOCTRL(H) T9 I/O(A) V18 GNDPLL(2)

B7 I/O(F) D16 I/O(D) H5 VCC N2 I/O(H) T10 I/O(A) V19 GND

B8 I/O(F) D17 I/O(D) H15 VCC N3 I/O(H) T11 CLK(3)/

PLLIN(1) W1 GND

B9 TMS D18 I/O(D) H16 VCC N4 I/O(H) T12 I/O(B) W2 PLLRST(3)

B10 CLK(6) D19 I/O(D) H17 I/O(D) N5 VCC T13 I/O(B) W3 I/O(A)

B11 I/O(E) E1 I/O(G) H18 I/O(D) N15 VCC T14 I/O(B) W4 I/O(A)

B12 I/O(E) E2 I/O(G) H19 I/O(D) N16 I/O(C) T15 I/O(B) W5 I/O(A)

B13 IOCTRL(E) E3 VCCIO(G) J1 I/O(G) N17 I/O(C) T16 I/O(B) W6 I/O(A)

B14 I/O(E) E4 I/O(F) J2 I/O(G) N18 IOCTRL(C) T17 VCCPLL(2) W7 I/O(A)

B15 I/O(E) E5 GND J3 VCCIO(G) N19 IOCTRL(C) T18 I/O(B) W8 I/O(A)

B16 I/O(E) E6 VCC J4 I/O(G) P1 I/O(H) T19 I/O(B) W9 TDI

B17 VCCPLL(1) E7 VCC J5 GND P2 I/O(H) U1 I/O(A) W10 CLK(2)/

PLLIN(2)

B18 GNDPLL(1) E8 VCC J15 VCC P3 IOCTRL(H) U2 I/O(A) W11 I/O(B)

B19 PLLOUT(0) E9 VCC J16 I/O(C) P4 INREF(H) U3 VCCPLL(3) W12 I/O(B)

C1 I/O(F) E10 GND J17 VCCIO(D) P5 VCC U4 I/O(A) W13 I/O(B)

C2 VCCPLL(0) E11 GND J18 I/O(D) P15 GND U5 VCCIO(A) W14 IOCTRL(B)

C3 I/O(F) E12 VCC J19 I/O(D) P16 I/O(C) U6 INREF(A) W15 I/O(B)

C4 I/O(F) E13 VCC K1 VCC P17 I/O(C) U7 I/O(A) W16 I/O(B)

C5 VCCIO(F) E14 GND K2 TCK P18 I/O(C) U8 I/O(A) W17 I/O(B)

C6 IOCTRL(F) E15 GND K3 I/O(G) P19 I/O(C) U9 VCCIO(A) W18 I/O(B)

C7 I/O(F) E16 I/O(D) K4 I/O(G) R1 I/O(H) U10 CLK(0) W19 PLLOUT(1)

C8 I/O(F) E17 VCCIO(D) K5 GND R2 I/O(H) U11 VCCIO(B)

C9 VCCIO(F) E18 INREF(D) K15 GND R3 VCCIO(H) U12 I/O(B)

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6500 - 484 PBGA Pinout Diagram

Top

Bottom

Eclipse

QL6500-4PS484C

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

22 21

Pin A1

Corner

Pin A1

www.quicklogic.com

•

Eclipse Family Data Sheet Rev. F

QL6500 - 484 PBGA Pinout Table

Table 32: 484 PBGA Pinout Table

Ball Function Ball Function Ball Function Ball Function Ball Function Ball Function

A1 I/O(A) C1 I/O(A) E1 IOCTRL(A) G1 I/O(A) J1 I/O(A) L1

CLK(4)/

DEDCLK/

PLLIN(0)

A2 PLLRST(3) C2 I/O(A) E2 I/O(A) G2 I/O(A) J2 I/O(A) L2 CLK(0)

A3 I/O(A) C3 VCCPLL(3) E3 I/O(A) G3 I/O(A) J3 I/O(A) L3 CLK(2)/PLLIN(2)

A4 I/O(A) C4 PLLOUT(2) E4 I/O(A) G4 I/O(A) J4 I/O(A) L4 I/O(A)

A5 I/O(A) C5 I/O(A) E5 I/O(A) G5 I/O(A) J5 I/O(A) L5 I/O(A)

A6 I/O(H) C6 I/O(H) E6 I/O(H) G6 I/O(A) J6 I/O(A) L6 I/O(A)

A7 I/O(H) C7 I/O(H) E7 I/O(H) G7 GND J7 I/O(A) L7 GND

A8 IOCTRL(H) C8 I/O(H) E8 I/O(H) G8 I/O(H) J8 VCC L8 GND

A9 I/O(H) C9 IOCTRL(H) E9 I/O(H) G9 I/O(H) J9 GND L9 GND

A10 I/O(H) C10 I/O(H) E10 I/O(H) G10 I/O(H) J10 VCC L10 GND

A11 I/O(H) C11 I/O(H) E11 VDED2 G11 I/O(G) J11 VCC L11 GND