LMH6618 Single/LMH6619 Dual 130 MHz, 1.25 mA RRIO Operational Amplifiers General Description Features The LMH6618 (single, with shutdown) and LMH6619 (dual) are 130 MHz rail-to-rail input and output amplifiers designed for ease of use in a wide range of applications requiring high speed, low supply current, low noise, and the ability to drive complex ADC and video loads. The operating voltage range extends from 2.7V to 11V and the supply current is typically 1.25 mA per channel at 5V. The LMH6618 and LMH6619 are members of the PowerWise(R) family and have an exceptional power-to-performance ratio. The amplifier's voltage feedback design topology provides balanced inputs and high open loop gain for ease of use and accuracy in applications such as active filter design. Offset voltage is typically 0.1 mV and settling time to 0.01% is 120 ns which combined with an 100 dBc SFDR at 100 kHz makes the part suitable for use as an input buffer for popular 8-bit, 10-bit, 12-bit and 14-bit mega-sample ADCs. The input common mode range extends 200 mV beyond the supply rails. On a single 5V supply with a ground terminated 150 load the output swings to within 37 mV of the ground rail, while a mid-rail terminated 1 k load will swing to 77 mV of either rail, providing true single supply operation and maximum signal dynamic range on low power rails. The amplifier output will source and sink 35 mA and drive up to 30 pF loads without the need for external compensation. The LMH6618 has an active low disable pin which reduces the supply current to 72 A and is offered in the space saving 6-Pin TSOT23 package. The LMH6619 is offered in the 8-Pin SOIC package. The LMH6618 and LMH6619 are available with a -40C to +125C extended industrial temperature grade. VS = 5V, RL = 1 k, TA = 25C and AV = +1, unless otherwise specified. 2.7V to 11V Operating voltage range 1.25 mA Supply current per channel 130 MHz Small signal bandwidth 0.6 mV Input offset voltage (limit at 25C) 55 V/s Slew rate 90 ns Settling time to 0.1% 120 ns Settling time to 0.01% 100 dBc SFDR (f = 100 kHz, AV = +1, VOUT = 2 VPP) 15 MHz 0.1 dB bandwidth (AV = +2) 10 nV/Hz Low voltage noise -40C to +125C Industrial temperature grade Rail-to-Rail input and output Applications ADC driver DAC buffer Active filters High speed sensor amplifier Current sense amplifier Portable video STB, TV video amplifier Typical Application 20195829 WEBENCH(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 201958 www.national.com LMH6618 Single/LMH6619 Dual 130 MHz, 1.25 mA RRIO Operational Amplifiers August 12, 2008 LMH6618/LMH6619 Supply Voltage (VS = V+ - V-) Junction Temperature (Note 3) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Operating Ratings V+ 12V 150C max (Note 1) Supply Voltage (VS = - Ambient Temperature Range (Note 3) ESD Tolerance (Note 2) Human Body Model For input pins only For all other pins Machine Model V-) 2.7V to 11V -40C to +125C Package Thermal Resistance (JA) 6-Pin TSOT23 8-Pin SOIC 2000V 2000V 200V 231C/W 160C/W +3V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TJ = +25C, V+ = 3V, V- = 0V, DISABLE = 3V, VCM = VO = V+/2, AV = +1 (RF = 0), otherwise RF = 2 k for AV +1, RL = 1 k || 5 pF. Boldface Limits apply at temperature extremes. (Note 4) Symbol Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) Units Frequency Domain Response SSBW -3 dB Bandwidth Small Signal GBW Gain Bandwidth (LMH6618) GBW Gain Bandwidth (LMH6619) LSBW -3 dB Bandwidth Large Signal AV = 1, RL = 1 k, VOUT = 0.2 VPP 120 AV = 2, -1, RL = 1 k, VOUT = 0.2 VPP 56 AV = 10, RF = 2 k, RG = 221, MHz 55 71 MHz 55 63 MHz RL = 1 k, VOUT = 0.2 VPP AV = 10, RF = 2 k, RG = 221, RL = 1 k, VOUT = 0.2 VPP AV = 1, RL = 1 k, VOUT = 2 VPP 13 AV = 2, RL = 150, VOUT = 2 VPP 13 MHz Peak Peaking AV = 1, CL = 5 pF 1.5 dB 0.1 dBBW 0.1 dB Bandwidth AV = 2, VOUT = 0.5 VPP , 15 MHz DG Differential Gain AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, 0.1 % 0.1 deg 36 ns 46 V/s RF = RG = 825 RL = 150 to V+/2 DP Differential Phase AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, RL = 150 to V+/2 Time Domain Response tr/tf Rise & Fall Time 2V Step, AV = 1 SR Slew Rate 2V Step, AV = 1 ts_0.1 0.1% Settling Time 2V Step, AV = -1 90 ts_0.01 0.01% Settling Time 2V Step, AV = -1 120 fC = 100 kHz, VOUT= 2 VPP, RL = 1 k 100 fC = 1 MHz, VOUT = 2 VPP, RL = 1 k 61 36 ns Noise and Distortion Performance SFDR Spurious Free Dynamic Range dBc fC = 5 MHz, VOUT = 2 VPP, RL = 1 k 47 en Input Voltage Noise Density f = 100 kHz 10 nV/ in Input Current Noise Density f = 100 kHz 1 pA/ CT Crosstalk (LMH6619) f = 5 MHz, VIN = 2 VPP 80 VCM = 0.5V (pnp active) VCM = 2.5V (npn active) 0.1 dB Input, DC Performance VOS Input Offset Voltage TCVOS Input Offset Voltage Temperature Drift (Note 5) 0.8 IB Input Bias Current VCM = 0.5V (pnp active) -1.4 -2.6 VCM = 2.5V (npn active) +1.0 +1.8 0.01 0.27 IOS Input Offset Current www.national.com 2 0.6 1.0 mV V/C A A Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) CIN Input Capacitance RIN Input Resistance CMVR Common Mode Voltage Range DC, CMRR 65 dB CMRR Common Mode Rejection Ratio VCM Stepped from -0.1V to 1.4V 78 96 VCM Stepped from 2.0V to 3.1V 81 107 RL = 1 k to +2.7V or +0.3V 85 98 RL = 150 to +2.6V or +0.4V 76 82 AOL Open Loop Voltage Gain Units 1.5 pF 8 M -0.2 3.2 V dB dB Output DC Characteristics VOUT Output Voltage Swing High (LMH6618) RL = 1 k to V+/2 (Voltage from V+ Supply Rail) 50 56 62 RL =150 to V+/2 160 172 198 Output Voltage Swing Low (LMH6618) RL = 1 k to V+/2 (Voltage from V- Supply Rail) 60 66 74 RL = 150 to V+/2 170 184 217 RL = 150 to V- 29 39 43 Output Voltage Swing High (LMH6619) RL = 1 k to V+/2 (Voltage from V+ Supply Rail) 50 56 62 RL =150 to V+/2 160 172 198 Output Voltage Swing Low (LMH6619) RL = 1 k to V+/2 (Voltage from V- Supply Rail) 62 68 76 RL =150 to V+/2 175 189 222 RL = 150 to V- 34 44 48 IOUT Linear Output Current VOUT = V+/2 (Note 6) ROUT Output Resistance f = 1 MHz 25 mV from either rail mV from either rail 35 mA 0.17 0.04 A Enable Pin Operation Enable High Voltage Threshold Enabled Enable Pin High Current VDISABLE = 3V Enable Low Voltage Threshold Disabled Enable Pin Low Current VDISABLE = 0V 2.0 V 1.0 V 1 A ton Turn-On Time 25 ns toff Turn-Off Time 90 ns 104 dB Power Supply Performance PSRR Power Supply Rejection Ratio DC, VCM = 0.5V, VS = 2.7V to 11V IS Supply Current (LMH6618) RL = 1.2 1.5 1.7 Supply Current (LMH6619) (per channel) RL = 1.2 1.5 1.75 Disable Shutdown Current DISABLE = 0V 59 85 ISD 3 84 mA A www.national.com LMH6618/LMH6619 Symbol LMH6618/LMH6619 +5V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TJ = +25C, V+ = 5V, V- = 0V, DISABLE = 5V, VCM = VO = V+/2, AV = +1 (RF = 0), otherwise RF = 2 k for AV +1, RL = 1 k || 5 pF. Boldface Limits apply at temperature extremes. Symbol Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) Units Frequency Domain Response SSBW -3 dB Bandwidth Small Signal GBW Gain Bandwidth (LMH6618) GBW Gain Bandwidth (LMH6619) AV = 1, RL = 1 k, VOUT = 0.2 VPP 130 AV = 2, -1, RL = 1 k, VOUT = 0.2 VPP 53 AV = 10, RF = 2 k, RG = 221, MHz 54 64 MHz 54 57 MHz RL = 1 k, VOUT = 0.2 VPP AV = 10, RF = 2 k, RG = 221, RL = 1 k, VOUT = 0.2 VPP LSBW -3 dB Bandwidth Large Signal AV = 1, RL = 1 k, VOUT = 2 VPP 15 AV = 2, RL = 150, VOUT = 2 VPP 15 MHz Peak Peaking AV = 1, CL = 5 pF 0.5 dB 0.1 dBBW 0.1 dB Bandwidth AV = 2, VOUT = 0.5 VPP, 15 MHz DG Differential Gain 0.1 % 0.1 deg 30 ns 55 V/s RF = RG = 1 k AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, RL = 150 to DP Differential Phase V+/2 AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, RL = 150 to V+/2 Time Domain Response tr/tf Rise & Fall Time 2V Step, AV = 1 SR Slew Rate 2V Step, AV = 1 ts_0.1 0.1% Settling Time 2V Step, AV = -1 90 ts_0.01 0.01% Settling Time 2V Step, AV = -1 120 fC = 100 kHz, VOUT = 2 VPP, RL = 1 k 100 fC = 1 MHz, VOUT = 2 VPP, RL = 1 k 88 fC = 5 MHz, VO = 2 VPP, RL = 1 k 61 44 ns Distortion and Noise Performance SFDR Spurious Free Dynamic Range dBc en Input Voltage Noise Density f = 100 kHz 10 nV/ in Input Current Noise Density f = 100 kHz 1 pA/ CT Crosstalk (LMH6619) f = 5 MHz, VIN = 2 VPP 80 VCM = 0.5V (pnp active) VCM = 4.5V (npn active) 0.1 dB Input, DC Performance VOS Input Offset Voltage TCVOS Input Offset Voltage Temperature Drift (Note 5) 0.8 IB Input Bias Current VCM = 0.5V (pnp active) -1.5 -2.4 VCM = 4.5V (npn active) +1.0 +1.9 0.26 IOS Input Offset Current 0.01 CIN Input Capacitance 1.5 RIN Input Resistance CMVR Common Mode Voltage Range DC, CMRR 65 dB CMRR Common Mode Rejection Ratio VCM Stepped from -0.1V to 3.4V 81 98 VCM Stepped from 4.0V to 5.1V 84 108 RL = 1 k to +4.6V or +0.4V 84 100 RL = 150 to +4.5V or +0.5V 78 83 AOL Open Loop Voltage Gain www.national.com 0.6 1.0 V/C 4 A A pF 8 -0.2 mV M 5.2 V dB dB Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) Units Output DC Characteristics VOUT Output Voltage Swing High (LMH6618) RL = 1 k to V+/2 (Voltage from V+ Supply Rail) 60 73 82 230 255 295 75 83 96 RL = 150 to V+/2 250 270 321 RL = 150 to V- 32 43 45 60 73 82 230 255 295 77 85 98 RL = 150 to V+/2 255 275 326 RL = 150 to V- 37 48 50 RL = 150 to V+/2 Output Voltage Swing Low (LMH6618) RL = 1 k to V+/2 (Voltage from V- Supply Rail) Output Voltage Swing High (LMH6619) RL = 1 k to V+/2 (Voltage from V+ Supply Rail) RL = 150 to V+/2 Output Voltage Swing Low (LMH6619) RL = 1 k to V+/2 (Voltage from V- Supply Rail) IOUT Linear Output Current VOUT = V+/2 (Note 6) ROUT Output Resistance f = 1 MHz 25 mV from either rail mV from either rail 35 mA 0.17 1.2 A Enable Pin Operation Enable High Voltage Threshold Enabled Enable Pin High Current VDISABLE = 5V Enable Low Voltage Threshold Disabled Enable Pin Low Current VDISABLE = 0V 3.0 V 2.0 V 2.5 A ton Turn-On Time 25 ns toff Turn-Off Time 90 ns Power Supply Performance PSRR Power Supply Rejection Ratio DC, VCM = 0.5V, VS = 2.7V to 11V IS Supply Current (LMH6618) ISD 84 104 dB RL = 1.25 1.5 1.7 Supply Current (LMH6619) (per channel) RL = 1.3 1.5 1.75 Disable Shutdown Current DISABLE = 0V 72 105 mA A 5V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TJ = +25C, V+ = 5V, V- = -5V, DISABLE = 5V, VCM = VO = 0V, AV = +1 (RF = 0), otherwise RF = 2 k for AV +1, RL = 1 k || 5 pF. Boldface Limits apply at temperature extremes. Symbol Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) Units Frequency Domain Response SSBW GBW -3 dB Bandwidth Small Signal Gain Bandwidth (LMH6618) AV = 1, RL = 1 k, VOUT = 0.2 VPP 140 AV = 2, -1, RL = 1 k, VOUT = 0.2 VPP 53 AV = 10, RF = 2 k, RG = 221, MHz 54 65 MHz 54 58 MHz RL = 1 k, VOUT = 0.2 VPP GBW Gain Bandwidth (LMH6619) AV = 10, RF = 2 k, RG = 221, RL = 1 k, VOUT = 0.2 VPP 5 www.national.com LMH6618/LMH6619 Symbol LMH6618/LMH6619 Symbol LSBW Parameter -3 dB Bandwidth Large Signal Condition AV = 1, RL = 1 k, VOUT = 2 VPP 16 AV = 2, RL = 150, VOUT = 2 VPP 15 Peak Peaking AV = 1, CL = 5 pF 0.1 dBBW 0.1 dB Bandwidth AV = 2, VOUT = 0.5 VPP, DG Differential Gain Units MHz 0.05 dB 15 MHz 0.1 % 0.1 deg 30 ns 57 V/s RF = RG = 1.21 k AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, RL = 150 to DP Min Typ Max (Note 8) (Note 7) (Note 8) Differential Phase V+/2 AV = +2, 4.43 MHz, 0.6V < VOUT < 2V, RL = 150 to V+/2 Time Domain Response tr/tf Rise & Fall Time 2V Step, AV = 1 SR Slew Rate 2V Step, AV = 1 ts_0.1 0.1% Settling Time 2V Step, AV = -1 90 ts_0.01 0.01% Settling Time 2V Step, AV = -1 120 fC = 100 kHz, VOUT = 2 VPP, RL = 1 k 100 fC = 1 MHz, VOUT = 2 VPP, RL = 1 k 88 fC = 5 MHz, VOUT = 2 VPP, RL = 1 k 70 45 ns Noise and Distortion Performance SFDR Spurious Free Dynamic Range dBc en Input Voltage Noise Density f = 100 kHz 10 nV/ in Input Current Noise Density f = 100 kHz 1 pA/ CT Crosstalk (LMH6619) f = 5 MHz, VIN = 2 VPP 80 VCM = -4.5V (pnp active) VCM = 4.5V (npn active) 0.1 dB Input DC Performance VOS Input Offset Voltage TCVOS Input Offset Voltage Temperature Drift (Note 5) 0.9 IB Input Bias Current VCM = -4.5V (pnp active) -1.5 -2.4 VCM = 4.5V (npn active) +1.0 +1.9 0.26 IOS Input Offset Current 0.01 CIN Input Capacitance 1.5 RIN Input Resistance CMVR Common Mode Voltage Range DC, CMRR 65 dB CMRR Common Mode Rejection Ratio VCM Stepped from -5.1V to 3.4V 84 100 VCM Stepped from 4.0V to 5.1V 83 108 RL = 1 k to +4.6V or -4.6V 86 95 RL = 150 to +4.3V or -4.3V 79 84 AOL Open Loop Voltage Gain www.national.com 0.6 1.0 V/C 6 A A pF 8 -5.2 mV M 5.2 V dB dB Parameter Condition Min Typ Max (Note 8) (Note 7) (Note 8) Units Output DC Characteristics VOUT Output Voltage Swing High (LMH6618) RL = 1 k to GND (Voltage from V+ Supply Rail) 100 111 126 430 457 526 110 121 136 RL = 150 to GND 440 474 559 RL = 150 to V- 35 51 52 100 111 126 430 457 526 115 126 141 RL = 150 to GND 450 484 569 RL = 150 to V- 45 61 62 RL = 150 to GND Output Voltage Swing Low (LMH6618) RL = 1 k to GND (Voltage from V- Supply Rail) Output Voltage Swing High (LMH6619) RL = 1 k to GND (Voltage from V+ Supply Rail) RL = 150 to GND Output Voltage Swing Low (LMH6619) RL = 1 k to GND (Voltage from V- Supply Rail) IOUT Linear Output Current VOUT = V+/2 (Note 6) ROUT Output Resistance f = 1 MHz 25 mV from either rail mV from either rail 35 mA 0.17 16 A Enable Pin Operation Enable High Voltage Threshold Enabled Enable Pin High Current VDISABLE = +5V Enable Low Voltage Threshold Disabled Enable Pin Low Current VDISABLE = -5V 0.5 V -0.5 V 17 A ton Turn-On Time 25 ns toff Turn-Off Time 90 ns Power Supply Performance PSRR Power Supply Rejection Ratio DC, VCM = -4.5V, VS = 2.7V to 11V IS Supply Current (LMH6618) ISD 84 104 dB RL = 1.35 1.6 1.9 Supply Current (LMH6619) (per channel) RL = 1.45 1.65 2.0 Disable Shutdown Current DISABLE = -5V 103 140 mA A Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum power dissipation is a function of TJ(MAX), JA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly onto a PC Board. Note 4: Boldface limits apply to temperature range of -40C to 125C Note 5: Voltage average drift is determined by dividing the change in VOS by temperature change. Note 6: Do not short circuit the output. Continuous source or sink currents larger than the IOUT typical are not recommended as it may damage the part. Note 7: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 8: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality Control (SQC) method. 7 www.national.com LMH6618/LMH6619 Symbol LMH6618/LMH6619 Connection Diagrams 6-Pin TSOT23 8-Pin SOIC 20195801 Top View 20195878 Top View Ordering Information Package Part Number Package Marking LMH6618MK 6-Pin TSOT23 8-Pin SOIC LMH6618MKE AE4A 250 Units Tape and Reel LMH6618MKX 3k Units Tape and Reel LMH6619MA 95 Units/Rail LMH6619MAE LMH6619MA LMH6619MAX www.national.com Transport Media NSC Drawing 1k Units Tape and Reel 250 Units Tape and Reel 2.5k Units Tape and Reel 8 MK06A M08A At TJ = 25C, AV = +1 (RF = 0), otherwise RF = 2 k for AV +1, unless otherwise specified. Closed Loop Frequency Response for Various Supplies Closed Loop Frequency Response for Various Supplies 20195831 20195816 Closed Loop Frequency Response for Various Supplies Closed Loop Frequency Response for Various Supplies 20195815 20195817 Closed Loop Frequency Response for Various Temperatures Closed Loop Frequency Response for Various Temperatures 20195819 20195820 9 www.national.com LMH6618/LMH6619 Typical Performance Characteristics LMH6618/LMH6619 Closed Loop Gain vs. Frequency for Various Gains Large Signal Frequency Response 20195818 20195830 0.1 dB Gain Flatness for Various Supplies Small Signal Frequency Response with Various Capacitive Load 20195832 20195826 Small Signal Frequency Response with Capacitive Load and Various RISO HD2 vs. Frequency and Supply Voltage 20195835 20195827 www.national.com 10 HD2 and HD3 vs. Frequency and Load 20195871 20195836 HD2 and HD3 vs. Common Mode Voltage HD2 and HD3 vs. Common Mode Voltage 20195873 20195872 HD2 vs. Frequency and Gain HD3 vs. Frequency and Gain 20195875 20195874 11 www.national.com LMH6618/LMH6619 HD3 vs. Frequency and Supply Voltage LMH6618/LMH6619 Open Loop Gain/Phase HD2 vs. Output Swing 20195833 20195843 HD3 vs. Output Swing HD2 vs. Output Swing 20195844 20195845 HD2 vs. Output Swing HD3 vs. Output Swing 20195869 www.national.com 20195846 12 LMH6618/LMH6619 HD3 vs. Output Swing THD vs. Output Swing 20195847 20195870 Settling Time vs. Input Step Amplitude (Output Slew and Settle Time) Input Noise vs. Frequency 20195876 20195821 VOS vs. VOUT VOS vs. VOUT 20195849 20195850 13 www.national.com LMH6618/LMH6619 VOS vs. VCM VOS vs. VS (pnp) 20195852 20195851 VOS vs. VS (npn) VOS vs. IOUT 20195853 20195854 VOS Distribution (pnp and npn) IB vs. VS (pnp) 20195855 20195877 www.national.com 14 LMH6618/LMH6619 IB vs. VS (npn) IS vs. VS 20195857 20195856 VOUT vs. VS VOUT vs. VS 20195858 20195859 VOUT vs. VS Closed Loop Output Impedance vs. Frequency AV = +1 20195860 20195822 15 www.national.com LMH6618/LMH6619 PSRR vs. Frequency PSRR vs. Frequency 20195838 20195837 CMRR vs. Frequency Crosstalk Rejection vs. Frequency (Output to Output) 20195879 20195823 Small Signal Step Response Small Signal Step Response 20195805 www.national.com 20195806 16 LMH6618/LMH6619 Small Signal Step Response Small Signal Step Response 20195804 20195808 Small Signal Step Response Small Signal Step Response 20195809 20195807 Small Signal Step Response Small Signal Step Response 20195811 20195812 17 www.national.com LMH6618/LMH6619 Small Signal Step Response Large Signal Step Response 20195810 20195813 Large Signal Step Response Overload Recovery Waveform 20195814 20195824 IS vs. VDISABLE 20195861 www.national.com 18 The LMH6618 and LMH6619 are based on National Semiconductor's proprietary VIP10 dielectrically isolated bipolar process. This device family architecture features the following: * Complimentary bipolar devices with exceptionally high ft (8 GHz) even under low supply voltage (2.7V) and low bias current. * Common emitter push-push output stage. This architecture allows the output to reach within millivolts of either supply rail. * Consistent performance from any supply voltage (2.7V 11V) with little variation with supply voltage for the most important specifications (e.g. BW, SR, IOUT.) * Significant power saving compared to competitive devices on the market with similar performance. With 3V supplies and a common mode input voltage range that extends beyond either supply rail, the LMH6618 and LMH6619 are well suited to many low voltage/low power applications. Even with 3V supplies, the -3 dB BW (at AV = +1) is typically 120 MHz. The LMH6618 and LMH6619 are designed to avoid output phase reversal. With input over-drive, the output is kept near the supply rail (or as close to it as mandated by the closed loop gain setting and the input voltage). Figure 1 shows the input and output voltage when the input voltage significantly exceeds the supply voltages. 20195839 FIGURE 2. Input Equivalent Circuit During Shutdown When the LMH6618 is shutdown, there may be current flow through the internal diodes shown, caused by input potential, if present. This current may flow through the external feedback resistor and result in an apparent output signal. In most shutdown applications the presence of this output is inconsequential. However, if the output is "forced" by another device, the other device will need to conduct the current described in order to maintain the output potential. To keep the output at or near ground during shutdown when there is no other device to hold the output low, a switch using a transistor can be used to shunt the output to ground. SINGLE CHANNEL ADC DRIVER The low noise and wide bandwidth make the LMH6618 an excellent choice for driving a 12-bit ADC. Figure 3 shows the schematic of the LMH6618 driving an ADC121S101. The ADC121S101 is a single channel 12-bit ADC. The LMH6618 is set up in a 2nd order multiple-feedback configuration with a gain of -1. The -3 dB point is at 500 kHz and the -0.01 dB point is at 100 kHz. The 22 resistor and 390 pF capacitor form an antialiasing filter for the ADC121S101. The capacitor also stores and delivers charge to the switched capacitor input of the ADC. The capacitive load on the LMH6618 created by the 390 pF capacitor is decreased by the 22 resistor. Table 1 shows the performance data of the LMH6618 and the ADC121S101. 20195825 FIGURE 1. Input and Output Shown with CMVR Exceeded If the input voltage range is exceeded by more than a diode drop beyond either rail, the internal ESD protection diodes will start to conduct. The current flow in these ESD diodes should be externally limited. The LMH6618 can be shutdown by connecting the DISABLE pin to a voltage 0.5V below the supply midpoint which will reduce the supply current to typically less than 19 www.national.com LMH6618/LMH6619 100 A. The DISABLE pin is "active low" and should be connected through a resistor to V+ for normal operation. Shutdown is guaranteed when the DISABLE pin is 0.5V below the supply midpoint at any operating supply voltage and temperature. In the shutdown mode, essentially all internal device biasing is turned off in order to minimize supply current flow and the output goes into high impedance mode. During shutdown, the input stage has an equivalent circuit as shown in Figure 2. Application Information LMH6618/LMH6619 20195829 FIGURE 3. LMH6618 Driving an ADC121S101 TABLE 1. Performance Data for the LMH6618 Driving an ADC121S101 Parameter Measured Value Signal Frequency 100 kHz Signal Amplitude 4.5V SINAD 71.5 dB SNR 71.87 dB THD -82.4 dB SFDR 90.97 dB ENOB 11.6 bits www.national.com 20 layout is shown in Figure 4. The 0.1 F capacitors (C13 and C6) and the 10 F capacitors (C11 and C5) are located very close to the supply pins of the LMH6618 and the ADC121S101. 20195840 FIGURE 4. LMH6618 and ADC121S101 Layout ential 12-bit ADC. Table 2 shows the performance data of the LMH6619 and the ADC121S625. SINGLE TO DIFFERENTIAL ADC DRIVER Figure 5 shows the LMH6619 used to drive a differential ADC with a single-ended input. The ADC121S625 is a fully differ- 20195880 FIGURE 5. LMH6619 Driving an ADC121S625 21 www.national.com LMH6618/LMH6619 When the op amp and the ADC are using the same supply, it is important that both devices are well bypassed. A 0.1 F ceramic capacitor and a 10 F tantalum capacitor should be located as close as possible to each supply pin. A sample LMH6618/LMH6619 TABLE 2. Performance Data for the LMH6619 Driving an ADC121S625 Parameter Measured Value Signal Frequency 10 kHz Signal Amplitude 2.5V SINAD 67.9 dB SNR 68.29 dB THD -78.6 dB SFDR 75.0 dB ENOB 11.0 bits C121S705. The ADC121S705 is a fully differential 12-bit ADC. Performance with this circuit is similar to the circuit in Figure 3. DIFFERENTIAL ADC DRIVER The circuit in Figure 3 can be used to drive both inputs of a differential ADC. Figure 6 shows the LMH6619 driving an AD- 20195842 FIGURE 6. LMH6619 Driving an ADC121S705 www.national.com 22 20195848 FIGURE 7. DC Level Shifting 4th ORDER MULTIPLE FEEDBACK LOW-PASS FILTER Figure 8 shows the LMH6619 used as the amplifier in a multiple feedback low pass filter. This filter is set up to have a gain of +1 and a -3 dB point of 1 MHz. Values can be determined by using the WEBENCH(R) Active Filter Designer found at amplifiers.national.com. 20195828 FIGURE 8. 4th Order Multiple Feedback Low-Pass Filter 23 www.national.com LMH6618/LMH6619 The following example is for a VIN of 0V to 1V with a VOUT of 2V to 4V. 1. VIN = 0V to 1V 2. VINMID = 0V + (1V - 0V)/2 = 0.5V 3. VOUT = 2V to 4V 4. VOUTMID = 2V + (4V - 2V)/2 = 3V 5. Gain = (4V - 2V)/(1V - 0V) = 2 6. VOUT = 3V - 2 x 0.5V = 2 7. For the example the supply voltage will be +5V. 8. Noise gain = 2 + 2/5V = 2.4 9. RF = 2 k 10. R1 = 2 k/2 = 1 k 11. R2 = 2 k/(2.4-2) = 5 k 12. RG = 2 k/(2.4 - 1) = 1.43 k DC LEVEL SHIFTING Often a signal must be both amplified and level shifted while using a single supply for the op amp. The circuit in Figure 7 can do both of these tasks. The procedure for specifying the resistor values is as follows. 1. Determine the input voltage. 2. Calculate the input voltage midpoint, VINMID = VINMIN + (VINMAX - VINMIN)/2. 3. Determine the output voltage needed. 4. Calculate the output voltage midpoint, VOUTMID = VOUTMIN + (VOUTMAX - VOUTMIN)/2. 5. Calculate the gain needed, gain = (VOUTMAX - VOUTMIN)/ (VINMAX - VINMIN) 6. Calculate the amount the voltage needs to be shifted from input to output, VOUT = VOUTMID - gain x VINMID. 7. Set the supply voltage to be used. 8. Calculate the noise gain, noise gain = gain + VOUT/VS. 9. Set RF. 10. Calculate R1, R1 = RF/gain. 11. Calculate R2, R2 = RF/(noise gain-gain). 12. Calculate RG, RG= RF/(noise gain - 1). Check that both the VIN and VOUT are within the voltage ranges of the LMH6618. LMH6618/LMH6619 CURRENT SENSE AMPLIFIER With it's rail-to-rail input and output capability, low VOS, and low IB the LMH6618 is an ideal choice for a current sense amplifier application. Figure 9 shows the schematic of the LMH6618 set up in a low-side sense configuration which provides a conversion gain of 2V/A. Voltage error due to VOS can be calculated to be VOS x (1 + RF/RG) or 0.6 mV x 21 = 12.6 mV. Voltage error due to IO is IO x RF or 0.26 A x 1 k = 0.26 mV. Hence total voltage error is 12.6 mV + 0.26 mV or 12.86 mV which translates into a current error of 12.86 mV/(2 V/A) = 6.43 mA. (1) (2) 20195841 FIGURE 9. Current Sense Amplifier 20195865 TRANSIMPEDANCE AMPLIFIER By definition, a photodiode produces either a current or voltage output from exposure to a light source. A Transimpedance Amplifier (TIA) is utilized to convert this low-level current to a usable voltage signal. The TIA often will need to be compensated to insure proper operation. FIGURE 11. Bode Plot of Noise Gain Intersecting with Op Amp Open-Loop Gain Figure 11 shows the bode plot of the noise gain intersecting the op amp open loop gain. With larger values of gain, CT and RF create a zero in the transfer function. At higher frequencies the circuit can become unstable due to excess phase shift around the loop. A pole at fP in the noise gain function is created by placing a feedback capacitor (CF) across RF. The noise gain slope is flattened by choosing an appropriate value of CF for optimum performance. Theoretical expressions for calculating the optimum value of CF and the expected -3 dB bandwidth are: (3) 20195862 (4) FIGURE 10. Photodiode Modeled with Capacitance Elements Equation 4 indicates that the -3 dB bandwidth of the TIA is inversely proportional to the feedback resistor. Therefore, if the bandwidth is important then the best approach would be to have a moderate transimpedance gain stage followed by a broadband voltage gain stage. Table 3 shows the measurement results of the LMH6618 with different photodiodes having various capacitances (CPD) and a feedback resistance (RF) of 1 k. Figure 10 shows the LMH6618 modeled with photodiode and the internal op amp capacitances. The LMH6618 allows circuit operation of a low intensity light due to its low input bias current by using larger values of gain (RF). The total capacitance (CT) on the inverting terminal of the op amp includes the photodiode capacitance (C PD) and the input capacitance of the op amp (CIN). This total capacitance (CT) plays an important role in the stability of the circuit. The noise gain of this circuit determines the stability and is defined by: www.national.com 24 CPD CT CF CAL CF USED f -3 dB CAL f -3 dB MEAS Peaking (pF) (pF) (pF) (pF) (MHz) (MHz) (dB) 22 24 7.7 5.6 23.7 20 0.9 47 49 10.9 10 16.6 15.2 0.8 100 102 15.8 15 11.5 10.8 0.9 222 224 23.4 18 7.81 8 2.9 Note: GBWP = 65 MHz CT = CPD + CIN CIN = 2 pF VS = 2.5V Figure 12 shows the frequency response for the various photodiodes in Table 3. noise voltage, feedback resistor thermal noise, input noise current, photodiode noise current) do not all operate over the same frequency band. Therefore, when the noise at the output is calculated, this should be taken into account. The op amp noise voltage will be gained up in the region between the noise gain's zero and pole (fZ and fP in Figure 11). The higher the values of RF and CT, the sooner the noise gain peaking starts and therefore its contribution to the total output noise will be larger. It is obvious to note that it is advantageous to minimize CIN by proper choice of op amp or by applying a reverse bias across the diode at the expense of excess dark current and noise. DIFFERENTIAL CABLE DRIVER FOR NTSC VIDEO The LMH6618 and LMH6619 can be used to drive an NTSC video signal on a twisted-pair cable. Figure 13 shows the schematic of a differential cable driver for NTSC video. This circuit can be used to transmit the signal from a camera over a twisted pair to a monitor or display located a distance. C1 and C2 are used to AC couple the video signal into the LMH6619. The two amplifiers of the LMH6619 are set to a gain of 2 to compensate for the 75 back termination resistors on the outputs. The LMH6618 is set to a gain of 1. Because of the DC bias the output of the LMH6618 is AC coupled. Most monitors and displays will accept AC coupled inputs. 20195868 FIGURE 12. Frequency Response for Various Photodiode and Feedback Capacitors When analyzing the noise at the output of the TIA, it is important to note that the various noise sources (i.e. op amp 25 www.national.com LMH6618/LMH6619 TABLE 3. TIA (Figure 1) Compensation and Performance Results LMH6618/LMH6619 20195881 FIGURE 13. Differential Cable Driver www.national.com 26 LMH6618/LMH6619 Physical Dimensions inches (millimeters) unless otherwise noted 6-Pin TSOT23 NS Package Number MK06A 8-Pin SOIC NS Package Number M08A 27 www.national.com LMH6618 Single/LMH6619 Dual 130 MHz, 1.25 mA RRIO Operational Amplifiers For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com