M87C51FC CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER WITH 32 KBYTES USER PROGRAMMABLE EPROM Military M87C51FC3.5 MHz to 12 MHz, VCC e 5V g 20% M87C51FC-13.5 MHz to 16 MHz, VCC e 5V g 20% Y High Performance CHMOS EPROM Y 32 Programmable I/O Lines Y Three 16-Bit Timer/Counters Y 7 Interrupt Sources Y Programmable Clock Out Y Y Programmable Counter Array with: High Speed Output, Compare/Capture, Pulse Width Modulator, Watchdog Timer Capabilities Programmable Serial Channel with: Framing Error Detection Automatic Address Recognition Y TTL and CMOS Compatible Logic Levels Y 64K External Program Memory Space Y Up/Down Timer/Counter Y 64K External Data Memory Space Y Three Level Program Lock System Y MCSE-51 Fully Compatible Instruction Set Y Power Saving Idle and Power Down Modes Y ONCE (On-Circuit Emulation) Mode Y Available in Two Product Grades: MIL-STD-883, b 55 C to a 125 C (TC) Military Temperature Only (MTO) b 55 C to a 125 C (TC) Y 32K On-Chip EPROM Y 256 Bytes of On-Chip Data RAM Y Improved Quick Pulse Programming Algorithm Y Boolean Processor Y Available in 40-pin Cerdip and 44-pin LCC Packages MEMORY ORGANIZATION PROGRAM MEMORY: Up to 32 Kbytes of the program memory can reside in the on-chip EPROM. In addition the device can address up to 64K of program memory external to the chip. DATA MEMORY: This microcontroller has a 256 x 8 on-chip RAM. In addition it can address up to 64 Kbytes of external data memory. The Intel M87C51FC is a single-chip control-oriented microcontroller which is fabricated on Intel's reliable CHMOS III-E technology. Being a member of the MCS-51 family, the M87C51FC uses the same powerful instruction set, has the same architecture, and is pin-for-pin compatible with the existing MCS-51 family of products. The M87C51FC is an enhanced version of the 87C51. Its added features make it an even more powerful microcontroller for applications that require Pulse Width Modulation, High Speed I/O, and up/down counting capabilities such as motor control. It also has a more versatile serial channel that facilitates multiprocessor communications. January 1994 Order Number: 271114-004 M87C51FC 271114 - 1 Figure 1. M87C51FC Block Diagram 2 M87C51FC PACKAGES Part Prefix Package Type 87C51FC D R 40-Pin CERDIP 44-Pin LCC Port 0 is also the multiplexed low-order address and data bus during accesses to external Program and Data Memory. In this application it uses strong internal pullups when emitting1's, and can source and sink several LS TTL inputs. Port 0 also receives the code bytes during EPROM programming, and outputs the code bytes during program verification. External pullup resistors are required during program verification. Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pullups. The Port 1 output buffers can drive LS TTL inputs. Port 1 pins that have 1's written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL, on the data sheet) because of the internal pullups. In addition, Port 1 serves the functions of the following special features of the M87C51FC: 271114 - 2 Port Pin Alternate Function P1.0 T2 (External Count Input to Timer/ Counter 2), Clock-Out T2EX (Timer/Counter 2 Capture/ Reload Trigger and Direction Control) ECI (External Count Input to the PCA) DIP P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 271114 - 3 LCC Figure 2. Pin Connections PIN DESCRIPTIONS VCC: Supply voltage. VSS: Circuit ground. Port 0: Port 0 is an 8-bit, open drain, bidirectional I/O port. As an output port each pin can sink several LS TTL inputs. Port 0 pins that have 1's written to them float, and in that state can be used as high-impedance inputs. CEX0 (External I/O for Compare/ Capture Module 0) CEX1 (External I/O for Compare/ Capture Module 1) CEX2 (External I/O for Compare/ Capture Module 2) CEX3 (External I/O for Compare/ Capture Module 3) CEX4 (External I/O for Compare/ Capture Module 4) Port 1 receives the low-order address bytes during EPROM programming and verifying. Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pullups. The Port 2 output buffers can drive LS TTL inputs. Port 2 pins that have 1's written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL, on the data sheet) because of the internal pullups. 3 M87C51FC Port 2 emits the high-order address byte during fetches from external Program Memory and during accesses to external Data Memory that use 16-bit addresses (MOVX @ DPTR). In this application it uses strong internal pullups when emitting 1's. During accesses to external Data Memory that use 8-bit addresses (MOVX @ Ri), Port 2 emits the contents of the P2 Special Function Register. Some Port 2 pins receive the high-order address bits during EPROM programming and program verification. Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pullups. The Port 3 output buffers can drive LS TTL inputs. Port 3 pins that have 1's written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL, on the data sheet) because of the pullups. Port 3 also serves the functions of various special features of the MCS-51 Family, as listed below: Port Pin Alternate Function P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 RXD (serial input port) TXD (serial output port) INT0 (external interrupt 0) INT1 (external interrupt 1) T0 (Timer 0 external input) T1 (Timer 1 external input) WR (external data memory write strobe) RD (external data memory read strobe) Some Port 3 pins receive the high-order address bits during EPROM programming and program verification. RST: Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. An internal pulldown resistor permits a poweron reset with only a capacitor connected to VCC. ALE: Address Latch Enable output pulse for latching the low byte of the address during accesses to external memory. This pin (ALE/PROG) is also the program pulse input during EPROM programming for the M87C51FC. PSEN: Program Store Enable is the read strobe to external Program Memory. When the M87C51FC is executing code from external Program Memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external Data Memory. EA/VPP: External Access enable. EA must be strapped to VSS in order to enable the device to fetch code from external Program Memory locations 0000H to 0FFFFH. Note, however, that if either of the Program Lock bits are programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin also receives the programming supply voltage (VPP) during EPROM programming. XTAL1: Input to the inverting oscillator amplifier. XTAL2: Output from the inverting oscillator amplifier. OSCILLATOR CHARACTERISTICS XTAL1 and XTAL2 are the input and output, respectively, of a inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 3. Either a quartz crystal or ceramic resonator may be used. More detailed information concerning the use of the on-chip oscillator is available in Application Note AP-155, ``Oscillators for Microcontrollers.'' To drive the device from an external clock source, XTAL1 should be driven, while XTAL2 floats, as shown in Figure 4. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum high and low times specified on the data sheet must be observed. An external oscillator may encounter as much as a 100 pF load at XTAL1 when it starts up. This is due to interaction between the amplifier and its feedback capacitance. Once the external signal meets the VIL and VIH specifications the capacitance will not exceed 20 pF. In normal operation ALE is emitted at a constant rate of (/6 the oscillator frequency, and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external Data Memory. Throughout the remainder of this data sheet, ALE will refer to the signal coming out of the ALE/PROG pin, and the pin will be referred to as the ALE/PROG pin. 4 C1, C2 e 30 pF g 10 pF for Crystals e 10 pF for Ceramic Resonators 271114 - 4 Figure 3. Oscillator Connections M87C51FC With an external interrupt, INT0 and INT1 must be enabled and configured as level-sensitive. Holding the pin low restarts the oscillator but bringing the pin back high completes the exit. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put the device into Power Down. 271114 - 5 Figure 4. External Clock Drive Configuration DESIGN CONSIDERATION # The window on the M87C51FC must be covered IDLE MODE The user's software can invoke the Idle Mode. When the microcontroller is in this mode, power consumption is reduced. The Special Function Registers and the onboard RAM retain their values during Idle, but the processor stops executing instructions. Idle Mode will be exited if the chip is reset or if an enabled interrupt occurs. The PCA timer/counter can optionally be left running or paused during Idle Mode. POWER DOWN MODE To save even more power, a Power Down mode can be invoked by software. In this mode, the oscillator is stopped and the instruction that invoked Power Down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the Power Down mode is terminated. On the M87C51FC either a hardware reset or an external interrupt can cause an exit from Power Down. Reset redefines all the SFRs but does not change the on-chip RAM. An external interrupt allows both the SFRs and on-chip RAM to retain their values. To properly terminate Power down the reset or external interrupt should not be executed before VCC is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize (normally less than 10 ms). by an opaque label. Otherwise, the DC and AC characteristics may not be met, and the device may functionally be impaired. # When the idle mode is terminated by a hardware reset, the device normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory. ONCE MODE The ONCE (``On-Circuit Emulation'') Mode facilitates testing and debugging of systems using the M87C51FC without the M87C51FC having to be removed from the circuit. The ONCE Mode is invoked by: 1) Pull ALE low while the device is in reset and PSEN is high; 2) Hold ALE low as RST is deactivated. While the device is in ONCE Mode, the Port 0 pins go into a float state, and the other port pins and ALE and PSEN are weakly pulled high. The oscillator circuit remains active. While the M87C51FC is in this mode, an emulator or test CPU can be used to drive the circuit. Normal operation is restored when a normal reset is applied. Table 1. Status of the External Pins during Idle and Power Down Program Memory ALE PSEN Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power Down Internal 0 0 Data Data Data Data Power Down External 0 0 Float Data Data Data Mode PORT0 PORT1 PORT2 PORT3 NOTE: For more detailed information on the reduced power modes refer to Application Note AP-255, ``Military CHMOS: Designing with the M80C51BH.'' 5 M87C51FC ABSOLUTE MAXIMUM RATINGS* Case Temperature Under BiasAAA b 55 C to a 125 C Storage Temperature AAAAAAAAAA b 65 C to a 150 C Voltage on EA/VPP Pin to VSS AAAAAAA0V to a 13.0V Voltage on Any Other Pin to VSS AA b 0.5V to a 6.5V IOL Per I/O Pin AAAAAAAAAAAAAAAAAAAAAAAAAAA15 mA Power DissipationAAAAAAAAAAAAAAAAAAAAAAAAAA1.5W (based on PACKAGE heat transfer limitations, not device power consumption) NOTICE: This data sheet contains information on products in the sampling and initial production phases of development. The specifications are subject to change without notice. Verify with your local Intel Sales office that you have the latest data sheet before finalizing a design. *WARNING: Stressing the device beyond the ``Absolute Maximum Ratings'' may cause permanent damage. These are stress ratings only. Operation beyond the ``Operating Conditions'' is not recommended and extended exposure beyond the ``Operating Conditions'' may affect device reliability. ADVANCED INFORMATIONCONTACT INTEL FOR DESIGN-IN INFORMATION OPERATING CONDITIONS MIL-STD-883 Symbol Parameter Min Max Units TC Case Temperature (Instant On) b 55 a 125 C VCC Digital Supply Voltage 4.00 6.00 V fOSC Oscillator Frequency 3.5 16 MHz Military Temperature (MTO) Symbol Parameter Min Max Units TC Case Temperature (Instant On) b 55 a 125 C VCC Digital Supply Voltage 4.00 6.00 V fOSC Oscillator Frequency 3.5 16 MHz DC CHARACTERISTICS Symbol Parameter VIL Input Low Voltage VIH Input High Voltage (Except XTAL1, RST) VIH1 Input High Voltage (XTAL1, RST) VOL Output Low Voltage (Note 4) (Ports 1, 2, and 3) VOL1 VOH 6 (Over Specified Operating Conditions) Min Max Unit b 0.5 0.2 VCC b 0.1 V 0.2 VCC a 0.9 VCC a 0.5 V 0.7 VCC VCC a 0.5 V 0.3 V IOL e 100 mA (Note 1) 0.45 V IOL e 1.6 mA (Note 1) 1.0 V IOL e 3.5 mA (Note 1) 0.3 V IOL e 200 mA (Note 1) 0.45 V IOL e 3.2 mA (Note 1) 1.0 Output Low Voltage (Note 4) (Port 0, ALE, PSEN) Output High Voltage (Ports 1, 2, and 3, ALE, PSEN) Comments V IOL e 7.0 mA (Note 1) VCC b 0.3 V IOH e b 10 mA VCC b 0.7 V IOH e b 30 mA VCC b 1.5 V IOH e b 60 mA M87C51FC DC CHARACTERISTICS Symbol VOH1 (Over Specified Operating Conditions) (Continued) Parameter Output High Voltage (Port 0 in External Bus Mode) Unit Comments VCC b 0.3 Min Max V IOH e b 200 mA VCC b 0.7 V IOH e b 3.2 mA V IOH e b 7.0 mA VCC b 1.5 IIL Logical 0 Input Current (Ports 1, 2, and 3) b 75 ILI Input leakage Current (Port 0) g 10 mA 0 k VIN k VCC ITL Logical 1 to 0 Transition Current (Ports 1, 2, and 3) b 750 mA VIN e 2V RRST RST Pulldown Resistor 225 KX CIO Pin Capacitance 10 pF ICC Power Supply Current: Running at 12 MHz (Figure 6) Idle Mode at 12 MHz (Figure 7) Power Down Mode (Figure 8) Running at 16 MHz Idle Mode at 16 MHz Power Down Mode 16 MHz 40 mA VIN e 0.45V @1 MHz, 25 C (Note 3) 40 10 100 45 15 130 mA mA mA mA mA mA NOTES: 1. Capacitive loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1, 2 and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operations. In applications where capacitance loading exceeds 100 pFs, the noise pulse on the ALE signal may exceed 0.8V. In these cases, it may be desirable to qualify ALE with a Schmitt Trigger, or use an Address Latch with a Schmitt Trigger Strobe input. 2. Capacitive loading on Ports 0 and 2 cause the VOH on ALE and PSEN to drop below the 0.9 VCC specification when the address lines are stabilizing. 3. See Figures 6-9 for load circuits. Minimum VCC for Power Down is 2V. 4. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10mA Maximum IOL per 8-bit port Port 0: 26 mA Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 271114 - 7 271114 - 6 ICC Max at other frequencies is given by: Active Mode ICC Max e (Osc Freq c 3) a 4 Idle Mode ICC Max e (Osc Freq c 0.5) a 4 Where Osc Freq is in MHz, ICC is in mA. All other pins disconnected TCLCH e TCHCL e 5 ns Figure 6. ICC Load Circuits, Active Mode Figure 5. ICC vs Frequency 7 M87C51FC 271114 - 8 All other pins disconnected TCLCH e TCHCL e 5 ns Figure 7. ICC Load Circuit Idle Mode 271114 - 9 All other pins disconnected Figure 8. ICC Load Circuit, Power Down Mode. VCC e 2.0V to 5.5V. 271114 - 10 Figure 9. Clock Signal Waveform for ICC Tests in Active and Idle Modes. TCLCH e TCHCL e 5 ns. EXPLANATION OF THE AC SYMBOLS Each timing symbol has 5 characters. The first character is always a `T' (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. A: Address C: Clock D: Input Data H: Logic level HIGH I: Instruction (program memory contents) 8 L: Logic level LOW, or ALE P: PSEN Q: Output Data R: RD signal T: Time V: Valid W: WR signal X: No longer a valid logic level Z: Float For example, TAVLL e Time from Address Valid to ALE Low TLLPL e Time from ALE Low to PSEN Low M87C51FC AC CHARACTERISTICS (Over Specified Operating Conditions, Load Capacitance for Port 0, ALE/PROG and PSEN e 100 pF, Load Capacitance for All Other Outputs e 80 pF) ADVANCED INFORMATIONCONTACT INTEL FOR DESIGN-IN INFORMATION EXTERNAL PROGRAM MEMORY CHARACTERISTICS Symbol Parameter 12 MHz Oscillator Min 1/TCLCL Max 16 MHz Oscillator Min Max Oscillator Frequency Variable Oscillator Units Min Max 3.5 16 MHz TLHLL ALE Pulse Width 127 85 2TCLCL b 40 TAVLL Address Valid to ALE Low 43 23 TCLCL b 40 ns TLLAX Address Hold After ALE Low 53 33 TCLCL b 30 ns TLLIV ALE Low to Valid Instruction In TLLPL ALE Low to PSEN Low 234 53 205 150 4TCLCL b 100 33 TCLCL b 30 143 3TCLCL b 45 ns ns ns TPLPH PSEN Pulse Width TPLIV PSEN Low to Valid Instruction In TPXIX Input Instruction Hold After PSEN TPXIZ Input Instruction Float Float After PSEN 59 38 TCLCL b 25 ns TAVIV Address to Valid Instruction In 312 208 5TCLCL b 105 ns TPLAZ PSEN Low to Address Float 10 10 10 ns TRLRH RD Pulse Width 400 275 6TCLCL b 100 TWLWH WR Pulse Width 400 275 6TCLCL b 100 TRLDV RD Low to Valid Data In TRHDX Data Hold After RD TRHDZ Data Float After RD 107 65 2TCLCL b 60 ns TLLDV ALE Low to Valid Data In 517 350 8TCLCL b 150 ns TAVDV Address to Valid Data In 9TCLCL b 165 ns TLLWL ALE Low to RD or WR Low 200 3TCLCL a 50 ns TAVWL Address Valid to WR Low 203 120 4TCLCL b 130 ns TQVWX Data Valid before WR 33 13 TCLCL b 50 ns TWHQX Data Hold after WR 33 13 TCLCL b 50 ns TQVWH Data Valid to WR High 433 288 7TCLCL b 150 TRLAZ RD Low to Address Float TWHLH RD or WR High to ALE High 145 0 83 0 252 0 0 300 123 3TCLCL b 50 0 23 ns ns 0 238 103 TCLCL b 40 ns ns 5TCLCL b 165 398 138 0 43 0 147.5 585 ns 3TCLCL b 105 ns ns ns 0 ns TCLCL a 40 ns 9 M87C51FC EXTERNAL PROGRAM MEMORY READ CYCLE 271114 - 11 EXTERNAL DATA MEMORY READ CYCLE 271114 - 12 EXTERNAL DATA MEMORY WRITE CYCLE 271114 - 13 10 M87C51FC SERIAL PORT TIMING - SHIFT REGISTER MODE Test Conditions: Symbol TC e b 55 C to a 125 C; VCC e 5V g 10%; VSS e 0V; Load Capacitance e 80 pF Parameter 12 MHz Oscillator 16 MHz Oscillator Min 1 Min 0.75 Max Variable Oscillator Max Min 12TCLCL Units Max TXLXL Serial Port Clock Cycle Time TQVXH Output Data Setup to Clock Rising Edge 700 492 10TCLCL b 133 ns TXHQX Output Data Hold After Clock Rising Edge 50 8 2TCLCL b 117 ns TXHDX Input Data Hold After Clock Rising Edge Clock Rising Edge to Input Data Valid 0 0 0 ns TXHDV 700 ms 492 10TCLCL b 133 ns SHIFT REGISTER MODE TIMING WAVEFORMS 271114 - 14 EXTERNAL CLOCK DRIVE Symbol 1/TCLCL TCHCX TCLCX Parameter Oscillator Frequency M87C51FC M87C51FC-16 High Time Low Time TCLCH TCHCL Rise Time Fall Time Min Max Units 3.5 3.5 20 20 12 16 MHz ns ns 20 20 ns ns EXTERNAL CLOCK DRIVE WAVEFORM 271114 - 15 11 M87C51FC AC TESTING INPUT, OUTPUT WAVEFORMS FLOAT WAVEFORMS 271114 - 16 AC Inputs during testing are driven at VCC b 0.5V for a Logic ``1'' and 0.45V for a Logic ``0''. Timing measurements are made at VIH min for a Logic ``1'' and VIL max for a Logic ``0''. 271114 - 17 For timing purposes a port pin is no longer floating when a 100 mV change from load voltage occurs, and begins to float when a 100 mV change from the loaded VOH/VOL level occurs. IOL/IOH t g 20 mA. Table 2. EPROM Programming Modes RST PSEN ALE/ PROG EA/ VPP Program Code Data H L Verify Code Data H L H Program Encryption Array Address 0-3FH H L Program Lock Bits Bit 1 H Bit 2 H Mode Bit 3 Read Signature Byte P2.6 P2.7 P3.3 P3.6 P3.7 12.75V L H H H H H L L L H H 12.75V L H H L H L 12.75V H H H H H L 12.75V H H H L L H L 12.75V H L H H L H L H H L L L L L DEFINITION OF TERMS PROGRAMMING THE EPROM ADDRESS LINES: P1.0-P1.7, P2.0-P2.5, P3.4 - P3.5 respectively for A0-A15. The part must be running with a 4 MHz to 6 MHz oscillator. The address of an EPROM location to be programmed is applied to address lines while the code byte to be programmed in that location is applied to data lines. Control and program signals must be held at the levels indicated in Table 2. Normally EA/VPP is held at logic high until just before ALE/ PROG is to be pulsed. The EA/VPP is raised to VPP, ALE/PROG is pulsed low and then EA/VPP is returned to a high (also refer to timing diagrams). DATA LINES: P0.0-P0.7 for D0-D7. CONTROL SIGNALS: RST, PSEN, P2.6, P2.7, P3.3, P3.6, P3.7 PROGRAM SIGNALS: ALE/PROG, EA/VPP NOTE: Exceeding the VPP maximum for any amount of time could damage the device permanently. The VPP source must be well regulated and free of glitches. 12 M87C51FC 271114 - 18 *See Table 2 for proper input on these pins Figure 10. Programming the EPROM PROGRAMMING ALGORITHM Refer to Table 2 and Figures 10 and 11 for address, data, and control signals set up. To program the M87C51FC the following sequence must be exercised. 1. Input the valid address on the address lines. 2. Input the appropriate data byte on the data lines. 3. Activate the correct combination of control signals. 4. Raise EA/VPP from VCC to 12.75V g 0.25V. 5. Pulse ALE/PROG 5 times for the EPROM array, and 25 times for the encryption table and the lock bits. Repeat 1 through 5 changing the address and data for the entire array or until the end of the object file is reached. PROGRAM VERIFY Program verify may be done after each byte that is programmed, or after a block of bytes that is programmed. In either case a complete verify of the entire array that has been programmed will ensure a reliable programming of the M87C51FC. The lock bits cannot be directly verified. Verification of the lock bits is done by observing that their features are enabled. Refer to the EPROM Program Lock section in this data sheet. 5 Pulses 271114 - 19 Figure 11. Programming Signal's Waveforms 13 M87C51FC EPROM Program Lock Reading the Signature Bytes The M87C51FC has a 3-bit program lock system and a 64-byte encryption array which are designed to protect the onboard program and data against software piracy. The M87C51FC has 3 signature bytes in locations 30H, 31H, and 60H. To read these bytes follow the procedure for EPROM verify, but activate the control lines provided in Table 2 for Read Signature Byte. Location: 30H e 89H 31H e 58H Encryption Array 60H e FCH Within the EPROM array are 64 bytes of Encryption Array that are initially unprogrammed (all 1's). Every time that a byte is addressed during a verify, 5 address lines are used to select a byte of the Encryption Array. This byte is then exclusive-NOR'ed (XNOR) with the code byte, creating an Encryption Verify byte. The algorithm, with the array in the unprogrammed state (all 1's), will return the code in it's original, unmodified form. For programming the Encryption Array, refer to Table 2 (Programming the EPROM). Program Lock Bits The M87C51FC has 3 programmable lock bits that when programmed according to Table 3 will provide different levels of protection for the on-chip code and data. Erasing the EPROM also erases the encryption array and the program lock bits, returning the part to full functionality. Erasure Characteristics Erasure of the EPROM begins to occur when the chip is exposed to light with wavelength shorter than approximately 4,000 Angstroms. Since sunlight and fluorescent lighting have wavelengths in this range, exposure to these light sources over an extended time (about 1 week in sunlight, or 3 years in roomlevel fluorescent lighting) could cause inadvertent erasure. If an application subjects the device to this type of exposure, it is suggested that an opaque label be placed over the window. The recommended erasure procedure is exposure to ultraviolet light (at 2537 Angstroms) to an integrated dose of at least 15 W-sec/cm2. Exposing the EPROM to an ultraviolet lamp of 12,000 mW/cm2 rating for 30 minutes, at a distance of about 1 inch, should be sufficient. Erasure leaves all the EPROM Cells in a 1's state. Table 3. Program Lock Bits and the Features Program Lock Bits Protection Type LB1 LB2 LB3 1 U U U No Program Lock features enabled. (Code verify will still be encrypted by the Encryption Array if programmed.) 2 P U U MOVC instructions executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on Reset, and further programming of the EPROM is disabled. 3 P P U Same as 2, also verify is disabled. 4 P P P Same as 3, also external execution is disabled. Any other combination of the lock bits is not defined. 14 M87C51FC EPROM PROGRAMMING AND VERIFICATION CHARACTERISTICS (TA e 21 C to 27 C; VCC e 5V g 10%; VSS e 0V) ADVANCED INFORMATIONCONTACT INTEL FOR DESIGN-IN INFORMATION Symbol Parameter Min Max Units VPP Programming Supply Voltage 12.5 13.0 V IPP 1/TCLCL Programming Supply Current Oscillator Frequency 4 TAVGL Address Setup to PROG Low 48TCLCL TGHAX Address Hold after PROG 48TCLCL TDVGL Data Setup to PROG Low 48TCLCL TGHDX Data Hold after PROG 48TCLCL TEHSH (Enable) High to VPP 48TCLCL TSHGL VPP Setup to PROG Low TGHSL VPP Hold after PROG 10 TGLGH PROG Width 90 75 mA 6 MHz 10 ms ms 110 TAVQV Address to Data Valid 48TCLCL TELQV ENABLE Low to Data Valid 48TCLCL TEHQZ Data Float after ENABLE 0 TGHGL PROG High to PROG Low 10 ms 48TCLCL ms EPROM PROGRAMMING AND VERIFICATION WAVEFORMS 271114 - 20 15