Document Number: 94397 For technical questions, contact: ind-modules@vishay.com www.vishay.com
Revision: 11-Aug-08 1
Phase Control Thyristors
(Stud Version), 200 A
ST180SPbF Series
Vishay High Power Products
FEATURES
Center amplifying gate
International standard case TO-209AB (TO-93)
Hermetic metal case with ceramic insulator
(Also available with glass-metal seal up to 1200 V)
Compression bonded encapsulation for heavy duty
operations such as severe thermal cycling
Lead (Pb)-free
Designed and qualified for industrial level
TYPICAL APPLICATIONS
DC motor controls
Controlled DC power supplies
AC controllers
ELECTRICAL SPECIFICATIONS
PRODUCT SUMMARY
IT(AV) 200 A
TO-209AB (TO-93)
RoHS
COMPLIANT
MAJOR RATINGS AND CHARACTERISTICS
PARAMETER TEST CONDITIONS VALUES UNITS
IT(AV)
200 A
TC85 °C
IT(RMS) 314 A
ITSM
50 Hz 5000
A
60 Hz 5230
I2t
50 Hz 125
kA2s
60 Hz 114
VDRM/VRRM 400 to 2000 V
tqTypical 100 µs
TJ- 40 to 125 °C
VOLTAGE RATINGS
TYPE
NUMBER
VOLTAGE
CODE
VDRM/VRRM, MAXIMUM REPETITIVE PEAK
AND OFF-STATE VOLTAGE
V
VRSM, MAXIMUM
NON-REPETITIVE PEAK VOLTAGE
V
IDRM/IRRM MAXIMUM
AT TJ = TJ MAXIMUM
mA
ST180S
04 400 500
30
08 800 900
12 1200 1300
16 1600 1700
20 2000 2100
www.vishay.com For technical questions, contact: ind-modules@vishay.com Document Number: 94397
2Revision: 11-Aug-08
ST180SPbF Series
Vishay High Power Products Phase Control Thyristors
(Stud Version), 200 A
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum average on-state current
at case temperature IT(AV) 180° conduction, half sine wave 200 A
85 °C
Maximum RMS on-state current IT(RMS) DC at 76 °C case temperature 314
A
Maximum peak, one-cycle
non-repetitive surge current ITSM
t = 10 ms No voltage
reapplied
Sinusoidal half wave,
initial TJ = TJ maximum
5000
t = 8.3 ms 5230
t = 10 ms 100 % VRRM
reapplied
4200
t = 8.3 ms 4400
Maximum I2t for fusing I2t
t = 10 ms No voltage
reapplied
125
kA2s
t = 8.3 ms 114
t = 10 ms 100 % VRRM
reapplied
88
t = 8.3 ms 81
Maximum I2t for fusing I2t t = 0.1 to 10 ms, no voltage reapplied 1250 kA2s
Low level value of threshold voltage VT(TO)1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 1.08 V
High level value of threshold voltage VT(TO)2 (I > π x IT(AV)), TJ = TJ maximum 1.14
Low level value of on-state slope resistance rt1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 1.18 mΩ
High level value of on-state slope resistance rt2 (I > π x IT(AV)), TJ = TJ maximum 1.14
Maximum on-state voltage VTM Ipk = 570 A, TJ = 125 °C, tp = 10 ms sine pulse 1.75 V
Maximum holding current IHTJ = TJ maximum, anode supply 12 V resistive load 600 mA
Maximum (typical) latching current IL1000 (300)
SWITCHING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum non-repetitive rate of rise
of turned-on current dI/dt Gate drive 20 V, 20 Ω, tr 1 µs
TJ = TJ maximum, anode voltage 80 % VDRM
1000 A/µs
Typical delay time td
Gate current 1 A, dIg/dt = 1 A/µs
Vd = 0.67 % VDRM, TJ = 25 °C 1.0
µs
Typical turn-off time tq
ITM = 300 A, TJ = TJ maximum, dI/dt = 20 A/µs,
VR = 50 V, dV/dt = 20 V/µs, gate 0 V 100 Ω, tp = 500 µs 100
BLOCKING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum critical rate of rise
of off-state voltage dV/dt TJ = TJ maximum linear to 80 % rated VDRM 500 V/µs
Maximum peak reverse and
off-state leakage current
IRRM,
IDRM
TJ = TJ maximum, rated VDRM/VRRM applied 30 mA
Document Number: 94397 For technical questions, contact: ind-modules@vishay.com www.vishay.com
Revision: 11-Aug-08 3
ST180SPbF Series
Phase Control Thyristors
(Stud Version), 200 A Vishay High Power Products
Note
The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC
TRIGGERING
PARAMETER SYMBOL TEST CONDITIONS
VALUES UNITS
TYP. MAX.
Maximum peak gate power PGM TJ = TJ maximum, tp 5 ms 10 W
Maximum average gate power PG(AV) TJ = TJ maximum, f = 50 Hz, d% = 50 2.0
Maximum peak positive gate current IGM TJ = TJ maximum, tp 5 ms 3.0 A
Maximum peak positive gate voltage + VGM TJ = TJ maximum, tp 5 ms 20 V
Maximum peak negative gate voltage - VGM 5.0
DC gate current required to trigger IGT
TJ = - 40 °C
Maximum required gate trigger/
current/voltage are the lowest
value which will trigger all units
12 V anode to cathode applied
180 -
mATJ = 25 °C 90 150
TJ = 125 °C 40 -
DC gate voltage required to trigger VGT
TJ = - 40 °C 2.9 -
V
TJ = 25 °C 1.8 3.0
TJ = 125 °C 1.2 -
DC gate current not to trigger IGD
TJ = TJ maximum
Maximum gate current/voltage
not to trigger is the maximum
value which will not trigger any
unit with rated VDRM anode to
cathode applied
10 mA
DC gate voltage not to trigger VGD 0.25 V
THERMAL AND MECHANICAL SPECIFICATIONS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum operating junction
temperature range TJ- 40 to 125 °C
Maximum storage temperature range TStg - 40 to 150
Maximum thermal resistance,
junction to case RthJC DC operation 0.105
K/W
Maximum thermal resistance,
case to heatsink RthC-hs Mounting surface, smooth, flat and greased 0.04
Mounting torque, ± 10 %
Non-lubricated threads 31
(275) N · m
(lbf in)
Lubricated threads 24.5
(210)
Approximate weight 280 g
Case style See dimensions - link at the end of datasheeet TO-209AB (TO-93)
ΔRthJC CONDUCTION
CONDUCTION ANGLE SINUSOIDAL
CONDUCTION
RECTANGULAR
CONDUCTION TEST CONDITIONS UNITS
180° 0.015 0.012
TJ = TJ maximum K/W
120° 0.019 0.020
90° 0.025 0.027
60° 0.036 0.037
30° 0.060 0.060
www.vishay.com For technical questions, contact: ind-modules@vishay.com Document Number: 94397
4Revision: 11-Aug-08
ST180SPbF Series
Vishay High Power Products Phase Control Thyristors
(Stud Version), 200 A
Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics
Fig. 3 - On-State Power Loss Characteristics
Fig. 4 - On-State Power Loss Characteristics
80
90
100
110
120
130
0 40 80 120 160 200 240
Maximum Allowable Case Temperature (°C)
30° 60°
90°
120°
180°
Average On-state Current (A)
Conduction Angle
ST1 8 0 S Se r i e s
R (DC) = 0.105 K/ W
thJC
70
80
90
100
110
120
130
0 50 100 150 200 250 300 350
DC
30° 60°
90°
120° 180°
Avera ge On-st at e Current (A)
Maximum Allowable Case Temperature (°C)
Conduction Period
ST1 8 0 S Se r i e s
R (DC) = 0.105 K/ W
thJC
25 50 75 100 125
Maximum Allowable Ambient Temperature (°C)
R=0.0
8K
/W-DeltaR
thS
A
0.1K/ W
0.16K
/W
0.2K
/W
0.3K
/W
0.4K/W
0.5K/W
0.8K
/W
1.2K/W
0
50
100
150
200
250
300
350
0 40 80 120 160 200 240
180°
120°
90°
60°
30°
RM S Lim it
Conduction Angle
Maximum Average On-state Power Loss (W)
Average On-state Current (A)
ST1 8 0 S Se r i e s
T = 1 2 5 ° C
J
25 50 75 100 125
Maximum Allowable Ambient Temperature (°C)
R=0.08K
/W-DeltaR
thS
A
0.1K/W
0.16K
/W
0.2K/W
0.3K/W
0.4K
/W
0.5K
/W
0.8K/ W
1.2K
/W
0
50
100
150
200
250
300
350
400
450
500
0 40 80 120 160 200 240 280 320
DC
180°
120°
90°
60°
30°
RM S Li m it
Conduction Period
Maximum Average On-state Power Loss (W)
Average On-state Current (A)
ST180S Se ries
T = 12 5 ° C
J
Document Number: 94397 For technical questions, contact: ind-modules@vishay.com www.vishay.com
Revision: 11-Aug-08 5
ST180SPbF Series
Phase Control Thyristors
(Stud Version), 200 A Vishay High Power Products
Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current
Fig. 7 - On-State Voltage Drop Characteristics
Fig. 8 - Thermal Impedance ZthJC Characteristics
2000
2400
2800
3200
3600
4000
4400
4800
110100
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Pea k Ha lf Sine Wave On-st ate Current (A)
Init ia l T = 125°C
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
J
ST1 8 0 S Se r i e s
At Any Rated Load Condition And With
Ra ted V Ap plied Follow ing Surge.
RRM
2000
2500
3000
3500
4000
4500
5000
5500
0.01 0.1 1
Pulse Tra in Dura t ion ( s)
Versus Pulse Train Duration. Control
Peak Half Sine Wave On-state Current (A)
Initial T = 125°C
No Volta g e Rea p p lied
Ra t e d V Re a p p l i e d
RRM
J
ST180S Series
Maximum Non Repetitive Surge Current
Of Conduction May Not Be Maintained.
100
1000
10000
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
T = 2 5 ° C
J
Instantaneous On-state Current (A)
Instantaneous On-state Voltage (V)
T = 125°C
J
ST1 8 0 S Se r i e s
0.001
0.01
0.1
1
0.001 0.01 0.1 1 10
Square Wave Pulse Duration (s)
thJC
Transient Thermal Impedance Z (K/W)
ST1 8 0 S Se r i e s
Steady State Value
R = 0.105 K/ W
(DC Operation)
thJC
www.vishay.com For technical questions, contact: ind-modules@vishay.com Document Number: 94397
6Revision: 11-Aug-08
ST180SPbF Series
Vishay High Power Products Phase Control Thyristors
(Stud Version), 200 A
Fig. 9 - Gate Characteristics
ORDERING INFORMATION TABLE
0.1
1
10
100
0.001 0.01 0.1 1 10 100
VGD
IGD
(b)
(a)
Tj = 2 5 ° C
Tj = 1 2 5 ° C
Tj = - 4 0 ° C
(1) (2) (3)
In st a n t a n e o u s G a t e C u r r e n t ( A )
Instantaneous Gate Voltage (V)
Rectangular gate pulse
a) Recommended load line for
b) Recommended load line for
<=30% ra ted di/ dt : 10V, 10ohms
Frequency Limited by PG(AV)
rated di/dt : 20V, 10ohms; tr<=1 µs
tr<=1 µs
(1) PGM = 10W, tp = 4ms
(2) PGM = 20W, tp = 2ms
(3) PGM = 40W, tp = 1ms
(4) PGM = 60W, tp = 0.66ms
D e v i c e : ST1 8 0 S Se r i e s
(4)
1
- Thyristor
2
- Essential part number
3
- 0 = Converter grade
4
9
- Lead (Pb)-free
- S = Compression bonding stud
8
- V = Glass-metal seal (only up to 1200 V)
5
- Voltage code x 100 = V
RRM
(see Voltage Ratings table)
6
- P = Stud base 3/4"-16UNF2A threads
7
- 0 = Eyelet terminals (gate and auxiliary cathode leads)
1 = Fast-on terminals (gate and auxiliary cathode leads)
None = Ceramic housing (over 1200 V)
Note: For metric device M16 x 1.5 contact factory
Device code
51 324
6789
ST 18 0 S 20 P 0 PbF-
LINKS TO RELATED DOCUMENTS
Dimensions http://www.vishay.com/doc?95082
Outline Dimensions
www.vishay.com Vishay Semiconductors
Revision: 05-Mar-12 1Document Number: 95082
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TO-209AB (TO-93)
DIMENSIONS in millimeters (inches)
Note
(1) For metric device: M16 x 1.5 - length 21 (0.83) maximum
Fast-on terminals
White shrink
Red shrink
Red cathode
Red silicon rubber
210 (8.26) ± 10 (0.39)
C.S. 0.4 mm2
(0.0006 s.i.)
90 (3.54) MIN.
4.3 (0.17) DIA.
19 (0.75) MAX.
38.5 (1.52)
MAX.
16 (0.63) MAX.
8.5 (0.33) DIA.
Glass metal seal
28.5 (1.12) MAX. DIA.
220 (8.66) ± 10 (0.39)
SW 32
C.S. 25 mm2
(0.039 s.i.)
Flexible leads
4 (0.16) MAX.
35 (1.38) MAX.
3/4"-16UNF-2A (1)
27.5 (1.08) MAX.
White gate
White shrink
Red shrink
Red cathode
Red silicon rubber
210 (8.26) ± 10 (0.39)
C.S. 0.4 mm2
(0.006 s.i.)
38.5 (1.52)
MAX.
220 (8.66) ± 10 (0.39)
Ceramic housing
90 (3.54) MIN.
4.3 (0.17) DIA.
19 (0.75) MAX.
8.5 (0.33) DIA.
35 (1.38) MAX.
3/4"-16UNF-2A (1)
27.5 (1.08) MAX. SW 32
27.5 (1.08) MAX. DIA.
White gate
16 (0.63) MAX.
AMP. 280000-1
REF-250
9.5 (0.37) MIN.
22 (0.86) MIN.
C.S. 25 mm2
(0.039 s.i.)
Flexible leads
4 (0.16) MAX.
9.5 (0.37) MIN.
22 (0.86) MIN.
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.