Embest Mini8600B Processor Card Figure 1-1 Mini8600B Top-View Figure 1-2 Mini8600B Bottom-View Features Mechanical Parameters Dimensions: 60.0 mm x 27.0 mm (8 layer PCB design) Working temperature: 0~70 Celsius Humidity Range: 20% ~ 90% Input Voltage: 3.3V Processor TI AM3359 ARM Cortex-A8 microprocessor - 720-MHz ARM Cortex-A8 32-bit RISC MPU - NEONTM SIMD Coprocessor - 32KB/32KB of L1 Instruction/Data Cache with Single-Error Detection (parity) - 256KB of L2 Cache with Error Correcting Code (ECC) - SGX530 Graphics Engine - Programmable Real-Time Unit Subsystem Memory 2*256MByte DDR3 SDRAM 512MByte NAND Flash Expansion Interfaces and Signals Routed to Pins Two 0.4mm space 2*40-pin board-to-board male expansion connectors - TFT LCD Interface (support 24-bpp parallel RGB Interface LCD) - Two USB 2.0 OTG Ports With Integrated PHY, High-Speed - Three inter-integrated circuit (I2C) Bus interfaces - Six UART interfaces; - One SPI interface; - Two 10/100/1000 Mb/s Ethernet MAC (EMAC) with Management Data Input/Output (MDIO) module; - A multichannel audio serial ports (McASP); - 8-channel 12-bit ADC interfaces; - Two 4-line SD/MMC card interfaces; - GPMC bus 1 General Description Measuring only 60mm by 27mm, the Mini8600B processor card is a small form-factor controller board based on TI's Sitara AM3359 ARM Cortex-A8 processor. The tiny module integrates 2*256MBytes DDR3 SDRAM and 512Mbytes NAND Flash and uses two 0.4mm space 2*40-pin board-to-board male expansion connectors to bring out many hardware peripheral signals and GPIOs from the CPU. Embest has designed a single board computer SBC8600B which has an expansion board to carry the Mini8600B. The flexible design allows the fast and easy way of realizing and upgrading the controller's capabilities. In additional to those features offered by Mini8600B, the SBC8600B features 5 serial ports (including 2 RS232 and 3 TTL), 2 USB Host and 1 USB OTG, 2 Ethernet ports, CAN, RS485, LCD, Touch screen, Audio, ADC and more other peripherals. The SBC8600B is a ready-to-run platform to support for Linux 3.2.0, Android 2.3 and WinCE 7 operating systems. Figure 1-3 SBC8600B Single Board Computer Figure 1-4 Mini8600B Processor Card 2 Functional Block Diagram Figure 1-5 Mini8600B Function Block Diagram 3 Dimensions Figure 1-6 Mini8600B Dimension Chart 4 Two 0.4mm space 2*40-pin board-to-board expansion connectors Embest Mini8600 processor card is connected to the carrier board via two 0.4mm space 2*40-pin board-to-board male expansion connectors. The connector marked in red below is CN1; table 1-1 described the pin signals of CN1 connector. Table 1-1 CN1 Pin Signal Description 1 GND GND 2 VDDS_RTC Supply voltage for RTC 3 CLK_OUT1 Clock out1 4 CLK_OUT2 Clock out2 5 MMC0_DAT0 MMC0 data bus 6 MMC0_DAT1 MMC0 data bus 7 MMC0_DAT2 MMC0 data bus 8 GLOBLE_RESETN SYS_RESET IN/ OUTPUT 9 MMC0_DAT3 MMC0 data bus 10 AM335X_PWRON_RESETN CPU PWRON Reset 11 GND GND 12 GND GND 13 AM355X_PRU_UART0_CTS PRU UART0 Clear To Send 14 AM355X_PRU_UART0_RX PRU UART0 receive data 15 AM355X_PRU_UART0_RTS PRU UART0 request to send 16 AM355X_PRU_UART0_TX PRU UART0 transmit data 5 17 AM355X_UART0_RX UART0 receive data 18 AM355X_UART3_RX UART3 receive data 19 AM355X_UART0_TX UART0 transmit data 20 AM355X_UART3_TX UART3 transmit data 21 AM355X_CAN0_RX CAN0 receive data 22 AM355X_I2C0_SDA I2C0 master serial data 23 AM355X_CAN0_TX CAN0 transmit data 24 AM355X_I2C0_SCL I2C0 master serial clock 25 AM355X_UART4_RX UART4 receive data 26 AM355X_UART1_RX UART1 receive data 27 AM355X_UART4_TX UART4 transmit data 28 AM355X_UART1_TX UART1 transmit data 29 GND GND 30 GND GND 31 MII1_COL 32 AM355X_USB0_DRVVBUS USB0 controller VBUS control output 33 MII1_TX_CLK MII1 transmit clock 34 AM355X_USB1_DRVVBUS USB1 controller VBUS control output 35 MII1_TX_EN MII1 transmit enable 36 MII1_REF_CLK MII1 reference clock 37 MII1_TXD3 MII1 transmit data 38 MII1_CRS MII1 carrier sense 39 MII1_TXD2 MII1 transmit data 40 MII1_RX_ER MII1 receive data error 41 MII1_TXD1 MII1 transmit data 42 MII1_RX_DV MII1 receive data valid 43 MII1_TXD0 MII1 transmit data 44 MII1_RX_CLK MII1 receive clock 45 MII_MDIO MII MDIO DATA 46 MII1_RXD3 MII1 receive data 47 MII_MDC MII MDIO CLK 48 MII1_RXD2 MII1 receive data 49 GND GND MII1 collision detect 6 50 MII1_RXD1 MII1 receive data 51 AM355X_USB0_DM USB0 DM- 52 MII1_RXD0 MII1 receive data 53 AM355X_USB0_DP USB0 DP 54 MMC0_CMD MMC0 Command Signal 55 GND GND 56 USB0_VBUS USB0 bus voltage 57 AM355X_USB1_DM USB1 data- 58 AM355X_USB1_ID USB1 ID 59 AM355X_USB1_DP USB1 data+ 60 AM355X_USB0_ID USB0 ID 61 GND GND 62 USB1_VBUS USB1 bus voltage 63 GPMC_A0 GPMC address 64 GPMC_A7 GPMC address 65 GPMC_A5 GPMC address 66 GPMC_A11 GPMC address 67 GPMC_A4 GPMC address 68 GPMC_A10 GPMC address 69 GPMC_A3 GPMC address 70 GPMC_A9 GPMC address 71 GPMC_A2 GPMC address 72 GPMC_A8 GPMC address 73 GPMC_A6 GPMC address 74 GPMC_A1 GPMC address 75 GND GND 76 GND GND 77 VDD_3V3 Power 78 VDD_3V3 Power 79 VDD_3V3 Power 80 VDD_3V3 Power 7 The connector marked in red below is CN2; table 1-2 described the pin signals of CN2 connector. Table 1-2 CN2 Pin Signal Description 1 GND GND 2 GND GND 3 MCASP0_AHCLKX MCASP0 transmit master clock 4 MCASP0_ACLKX MCASP0 transmit bit clock 5 MCASP0_FSX MCASP0 transmit frame sync 6 MCASP0_AXR0 MCASP0 serial data(I/O) 7 MCASP0_AHCLKR MCASP0 receiver master clock 8 MMC0_CLK MMC0 clock 9 MCASP0_FSR MCASP0 receive frame sync 10 MCASP0_AXR1 MCASP0 serial data(I/O) 11 GND GND 12 GND GND 13 VDDA_ADC Supply voltage range for ADC 14 AM355X_ADC0 ADC0 15 AM355X_ADC1 ADC1 16 AM355X_ADC2 ADC2 17 AM355X_ADC3 ADC3 18 AM355X_ADC4 ADC4 19 AM355X_ADC5 ADC5 8 20 AM355X_ADC6 ADC6 21 AM355X_ADC7 ADC7 22 GND_ADC GND ADC 23 GND GND 24 GND GND 25 LCD_DATA1 LCD data bus 26 LCD_DATA12 LCD data bus 27 LCD_DATA0 LCD data bus 28 LCD_DATA10 LCD data bus 29 LCD_DATA5 LCD data bus 30 LCD_DATA13 LCD data bus 31 LCD_DATA4 LCD data bus 32 LCD_DATA11 LCD data bus 33 LCD_DATA6 LCD data bus 34 LCD_DATA14 LCD data bus 35 LCD_DATA8 LCD data bus 36 LCD_VSYNC LCD vertical sync 37 GND GND 38 GND GND 39 LCD_DATA9 LCD data bus 40 LCD_PCLK LCD pixel clock 41 LCD_DATA15 LCD data bus 42 GPMC_AD11 GPMC address & data 43 LCD_DATA3 LCD data bus 44 GPMC_AD15 GPMC address & data 45 LCD_DATA2 LCD data bus 46 GPMC_AD14 GPMC address & data 47 LCD_DATA7 LCD data bus 48 GPMC_WAIT0 GPMC wait0 49 LCD_HSYNC LCD horizontal sync 50 GPMC_BEN1 GPMC byte enable 1 51 GND GND 52 GND GND 9 53 LCD_EN LCD AC bias enable chip select 54 GPMC_WPN GPMC write protect 55 GPMC_AD13 GPMC address & data 56 GPMC_CSN3 GPMC chip select 57 GPMC_AD9 GPMC address & data 58 GPMC_CSN2 GPMC chip select 59 GPMC_AD10 GPMC address & data 60 GPMC_CLK GPMC clock 61 GPMC_AD8 GPMC address & data 62 GPMC_AD6 GPMC address & data 63 GPMC_AD12 GPMC address & data 64 GND GND 65 GND GND 66 GPMC_CSN1 GPMC chip select1 67 GPMC_ADVN_ALE GPMC address valid/address latch enable 68 GPMC_AD5 GPMC address & data 69 GPMC_BEN0_CLE GPMC byte enable 0/Command latch enable 70 GPMC_AD4 GPMC address & data 71 GPMC_OEN_REN GPMC output /read enable 72 GPMC_AD1 GPMC address & data 73 GPMC_AD2 GPMC address & data 74 GPMC_AD0 GPMC address & data 75 GPMC_AD3 GPMC address & data 76 GPMC_CSN0 GPMC chip select0 77 GPMC_AD7 GPMC address & data 78 GPMC_WEN GPMC write enable 79 GND GND 80 GND GND 10 Software Features OS Item BIOS Linux Kernel Driver Kernel Android Driver BIOS WinCE7 OAL Driver Remark NAND SPL MMC/SD (First boot loader) FAT NAND MMC/SD U-boot (Second boot loader) FAT NET Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ Linux-3.2.0 JFFS2/UBIFS file systems NAND Flash, SDRAM, Serial port, RTC, Ethernet, TFT LCD, Touch screen, TF card, USB OTG, Audio input/output, LED, Key, CAN, RS485, Power Management (backlight, PWM, ADC) (provided with source code) 2D/3D (not provided with source code) Linux-3.1.0 Gingerbread NAND Flash, SDRAM, Serial port, RTC, Ethernet, TFT LCD, Touch screen, TF card, USB OTG, Audio input/output, LED, Key, Power Management (backlight, PWM) (provided with source code) 2D/3D (not provided with source code) NAND X-loader MMC/SD (First boot loader) FAT NAND MMC/SD EBOOT (Second boot loader) FAT NET Boot parameter KILT(EMAC) Serial debug REBOOT Watchdog OAL module RTC Kernel profiler System timer Interrupt controller MMU NAND Flash, SDRAM, Serial port, RTC, Ethernet, TFT LCD, Touch screen, TF card, USB OTG, Audio input/output, LED, Key, RS485, Power Management (backlight) (provided with source code) CAN, 2D/3D (not provided with source code) 11 Order Information Order No. Item Options Price T400414 Mini8600B Processor Card A pair of 0.4mm space 2*40-pin board-to-board connectors (including the male and female connectors) SBC8600B Single Board Computer Please contact Embest Embest Technology Co., LTD. Room 509, Luohu Science&Technology Building, #85 Taining Rd., Shenzhen, Guangdong, China 518020 Tel: +86-755-25635656/25636285 Fax: +86-755-25616057 Email: market@embedinfo.com http://www.embedinfo.com/english http://www.armkits.com 12