Product Data Sheet
PD-0036-B
3M™ PC Boardmount
Plug and Receptacle, 2 mm
95X Series
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 1 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
1.0 SCOPE.....................................................................................................................................................................2
2.0 PRODUCT TESTED...............................................................................................................................................2
3.0 GENERAL CONDITIONS .....................................................................................................................................2
3.1 Test Specimens........................................................................................................................................................2
3.2 Standard Test Conditions ........................................................................................................................................2
4.0 TEST RESULTS SUMMARY................................................................................................................................3
5.0 TESTING ................................................................................................................................................................4
5.1 General ....................................................................................................................................................................4
Visual (Appearance) — IEC-512-2-1a......................................................................................................................4
Low Level Contact Resistance — IEC-512-2-2a.......................................................................................................4
5.2 Environmental .........................................................................................................................................................4
Durability — IEC-512-7-9a ......................................................................................................................................4
Dry Heat — IEC-512-6-11i.......................................................................................................................................4
Cold — IEC-512-6-11j..............................................................................................................................................5
Solderability — IEC-512-1-12a………………………………………………………………………………………………..5
5.3 Mechanical ..............................................................................................................................................................5
Mating and Unmating Forces — IEC-512-7-13b......................................................................................................5
5.4 Electrical..................................................................................................................................................................6
Dielectric Withstanding Voltage — IEC-512-2-4a....................................................................................................6
Insulation Resistance — IEC-512-2-2a........................................................................................................….…..…6
6.0 Heat Resistance
Heat Resistance Compliance — JEDEC-020C……………………………………………………………………...…….6
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 2 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
1.0 Scope
This data sheet summarizes test methods, test conditions and product performance for the 3M™ PC Boardmount,
2mm, product family. Both plug and receptacle, plated with 10µ” Gold at the mating area.
Testing has been conducted in accordance to IEC Std 60603-13 Perfomance Level 3
2.0 Product Tested
Product: 3M™ PC Boardmount Plug and Receptacle, 2 mm
Product Number: 950444-6102-AR; 950444-8200-AR; 951244-
2520-AR
Related Specification Sheet: TS-2155; TS-2167; TS-2157
Qualification also representative for
products related to Spec Sheets:
TS-2156; TS-2158, TS-2159, TS-2160, TS-2161,
TS-2162, TS-2163, TS-2164, TS-2165, TS-2166,
TS-2168, TS-2174, TS-2175
3.0 General Conditions
3.1 Test Specimens
The test specimens shall be strictly in compliance with the design, construction details and physical properties
detailed in the relevant Technical Specification Sheet (See Section 2).
3.2 Standard Test Conditions
The test shall be done under the following conditions:
Temperature: 15°C to 35°C
Relative Humidity: 45% to 75%
Atmospheric pressure: 650 to 800 mmHg
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 3 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
4.0 Test Results Summary
Items
Specification
Test Method Results
General Visual No defects such as deformation,
blister, damage, crack, etc.
IEC-512-2-1a Pass
Low Level Contact Resistance Max. R: (Initial) <20 m IEC-512-2-2a Pass
Environmental Durability Insertions/Withdrawals -50 cycles
Max. R: <20 m
IEC-512-7-9a Pass
Dry Heat No physical abnormalities after test
100 oC for 12 Hours
Max. R: <20 m
IEC-512-6-11i
Pass
Cold No physical abnormalities after test ---
--25oC for 16 Hours
Max. R: <20 m
IEC-512-6-11j Pass
Solderability Solder Coverage > 95% IEC-512-1-12a Pass
Mechanical Mating Forces Max force: 3N/ Contact
IEC-512-7-13b Pass
Electrical Dielectric Withstanding Voltage 1000 Vdc 1 min IEC-512-2-4a Pass
Insulation Resistance > 5 X 108 @ 100 Vdc IEC-512-2-3a Pass
Heat Resistance Compliance to solder profile MSL 1 JEDEC-020c Pass
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 4 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
5.0 Testing
Test methods are in accordance with IEC -512.
5.1 General
Visual (Appearance) — IEC-512-2-1a
Purpose
The purpose of this test is to visually examine and dimensionally inspect the connector in order to determine
whether the connector conforms to the applicable specification and detail documents not covered by performance
requirements.
Test Method
The examination shall be made in accordance with IEC-512-2-1a. The visual examination shall include inspection
of the following features as a minimum: workmanship, marking, materials, finish, standards, design and
construction. The dimensional inspection shall be a check for compliance with the outline drawings of the detail
specification.
Low Level Contact Resistance — IEC-512-2-2a
Purpose
The purpose of this test is to evaluate contact resistance characteristics of electrical contacts under conditions where
applied voltages and currents do not alter the physical contact interface or modify the conductive oxide films which
may be present.
Test Method
The low-signal level contact resistance shall be tested in accordance with IEC-512-2-2a with circuit current of 100
mA maximum and open circuit voltage of 20 mV maximum.
All readings are in milli-ohms.
5.2 Environmental
Durability — IEC-512-7-9a
Purpose
The purpose of this test is to determine the effects of subjecting electrical connectors to a conditioning action of
mating and unmating of connector simulating operations approximating the life of the connector.
Test Method
Connector durability shall be tested in accordance with IEC-512-7-9a
Condition: 50 Cycles
Max speed: 10 mm/s
Max. R: < 20 mΩ
Dry Heat — IEC-512-6-11i
Purpose
The purpose of this test is to determine the effects on the electrical and mechanical characteristics of the connector
resulting from exposure of the connector under specified condition of dry heat.
Test Method
Mated connectors shall be tested in accordance with IEC-512-6-11i.
Temperature: 100°C
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 5 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
Duration: 12 hours
Max. R: < 20 mΩ
Cold — IEC-512-11j
Purpose
The purpose of this test is to determine the effects on the electrical and mechanical characteristics of the connector
resulting from exposure under specified condition of cold.
Test Method
Mated connectors shall be tested in accordance with IEC-512-6-11j.
Temperature: -25°C
Duration: 16 hours
Max. R: < 20 mΩ
Solderability — IEC-512-1-12a
Purpose
This test is conducted to determine the suitability of connectors solder tails being adequate covered by solder after
dipping process.
Test Method
Mated connectors shall be tested in accordance with IEC-512-1-12a.
Solder: 96.5Sn/3.0Ag/0.5Cu
Solder bath temperature: 260°C
Flux: R type
Solder Coverage: > 95 %
5.3 Mechanical
Mating Forces — IEC-512-7-13b
Purpose
The purpose of this test is to determine the mechanical forces required to mate the electrical connectors.
Test Method
The mechanical forces required to mate these electrical connectors shell be determined in accordance with IEC-512-
7-13b.
Max speed: 100 mm / min
Maximum force per contact: 3 N
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 6 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
5.4 Electrical
Dielectric Withstanding Voltage — IEC-512-2-4a
Purpose
The purpose of this test is to prove that a given electrical connector can operate safely at its rated voltage and
withstand momentary overpotentials due to switching, surges, and other similar phenomena.
Test Method
Withstanding voltage shall be tested in accordance with IEC-512-2-4a.
Applied Voltage: 1000 Vdc
Duration: 1 minute
Measurement: Check for evidence of a breakdown
Insulation Resistance — IEC-512-2-3a
Purpose
The purpose of this test is to establish the methods and procedures to be followed in determining the resistance
offered by the insulation materials and the various seals of a connector to a direct current potential tending to
produce a leakage of current through or on the surface of these members.
Test Method
Insulation resistance shall be tested in accordance with IEC-512-2-3a.
Applied Voltage: 100 Vdc
Duration: 1 minutes
Measurement: Insulation Resistance
>5 X 108 @ 100 Vdc
Document Number: PD-0036_B Issue Date: 7/20/2010
Title: Product Data Sheet Supersedes: Rev. A
Subject: 3M™ PC Boardmount Plug and
Receptacle, 2 mm 95X Series
Page: 7 of 7
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
6.0 Heat Resistance
Heat Resistance Compliance — JEDEC-020C
Purpose
Purpose of this test is to assure that the part does not deform, crack, craze, blister or split under the heat
environment needed for Pb-Free Assemblies and soldering with non leaded solder.
Test Method
Avg Ramp –Up Rate
(Tsmax to Tp)
3°C / sec max
(200° - 260°C)
Preheat
Tsmin
Tsmax
Time (tsmin to tsmax)
150°C
200°C
60 - 180 sec
Time tL maintained above Temp TL
TL
tL
217°C
60 - 150 sec
Peak Tp/ Classification 260°C +3°C / MSL1
Time tp within 5°C of Tp 20 – 40 sec
Ramp – Down Rate
Time 25°C to Tp
6°C / sec max
8 minutes max.
Results
The 3M™ PC Boardmount Plug and Receptacle, 2mm, product family of parts is JEDEC-20C compliant.
Important Notice Warranty; Limited Remedy; Limited Liability.
The information we are furnishing you is being 3M’s product warranty is stated in its Product
provided free of charge and is based on tests Literature available upon request. 3M MAKES NO
performed at 3M laboratory facilities or by our OTHER WARRANTIES INCLUDING, BUT
suppliers. While we believe that these test results a NOT LIMITED TO, ANY IMPLIED
reliable, their accuracy or completeness is not WARRANTY OF MERCHANTABILITY OR
guaranteed. Your results may vary due to differences FITNESS FOR A PARTICULAR PURPOSE. If
in test types and conditions. This information is this product is defective within the warranty period
intended for use by persons with the knowledge and stated above, your exclusive remedy shall be, at 3M’s
technical skills to analyze, handle and use such option, to replace or repair the 3M product or refund
information. You must evaluate and determine stated above, your exclusive remedy shall be, at 3M’s
whether the product is suitable for your intended the purchase price of the 3M product. Except where
application. The foregoing information is provided prohibited by law, 3M will not be liable for any
“AS-IS”. In providing this information 3M makes no indirect, special, incidental or consequential loss
warranties regarding product use or performance, or damage arising from this 3M product,
including any implied warranty of merchantability or regardless of the legal theory asserted.
fitness for a particular use.
© 3M Copyright 2010
This document is the copyrighted property of the 3M Company and my not be reproduced
without 3M written permission or used for other than 3M authorized purposes.
3M is a trademark of the 3M Company
