CURRENT 1.0 Amper VOLTAGE 50 to 1000 Volts RL101F THRU RL107F Features * Plastic package has Underwriters Laboratory Flammability Classification 94-0 * Fast switching speed * Low forward voltage drop, high efficiency * High current capability * High reliability A-405 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data * Case : A-405 molded plastic body * Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 * Polarity : Color band denotes cathode end * Mounting Position : Any * Weight : 0.08 ounce, 0.22 gram 1.0(25.4) MIN. 0.025(0.6) 0.021(0.5) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25 ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols RL 101F RL 102F RL 103F RL 104F RL 105F RL 106F RL 107F Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=55 I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 25.0 Amps VF 1.3 Volts Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TA=55 5.0 100.0 Maximum reverse recovery time (Note 1) Trr Typical junction capacitance (Note 2) CJ Operating junction and storage temperature range A IR TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. 150 250 15.0 -65 to +150 500 ns pF RATINGS AND CHARACTERISTIC CURVES RL101F THRU RL107F FIG.2-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1.0 50 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 0.8 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT(A) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 0.6 0.4 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.2 0 0 25 50 75 100 125 150 175 40 30 20 10 0 AMBIENT TEMPERATURE ( ) 1 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 10 6.0 4.0 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 3 1 0.3 0.1 2.0 1.0 0.6 0.4 0.2 0.1 0.06 0.04 TJ=25 0.03 0.02 Pulse Width=300mS 0.01 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 TJ=25 1.6 0 1.8 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 200 100 50W NON INDUCTIVE 60 10W NON INDUCTIVE +0.5A Trr 40 (+) 20 D.U.T. PULSE GENERATOR (NOTE2) 25Vdc (APPROX) 10 6 ( TJ=25 ) 1W NON INDUCTIVE 4 2 1 0.1 0.2 0.4 1 2 4 REVERSE VOLTAGE. (V) 10 20 40 100 0 -0.25A OSCILLOSCOPE (NOTE1) NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm