● Suppli e r : Sams ung E lectr o- Mechanics CL31B104KBP5PNF
● Product : Multi-layer Ceram ic Capacitor CAP, 10 0 ㎋, 50V, ± 10%, X7R, 1206
● AEC-Q200 Qualified
A. Dim e ns ion
● Dimension
B. Sam s ung P a rt Number
CL 31 B K B P 5 P N F
①②③ ⑤⑥ ⑦ ⑧ ⑨ ⑩⑪
①Series Samsung Multi-layer Ceramic Capacitor
②Size (inch code) L : 3.20±0.15 mm W :1.60±0.15 mm
③Dielectric ⑧Inner electr ode Ni, Open Mode Design
④Capacitance ㎋Termination Metal-Epoxy
⑤Capacitance ± 10% Plating Sn 100% (Pb Free)
tolerance ⑨Product Automotive
⑥Rated Voltage V⑩Special code Normal
⑦Thickness 1.15±0.10 mm ⑪Packaging Embossed Type, 13" Reel
C. Reliability Test and Judgement c ondition
Test items
High Temperature Appearance : No abnormal exterior appearance Unpowered, 1,000hrs @ Max. temperature
Exposure Capacitance Change Within ±10 % Measurement at 24±2hrs after test conclusion
Tan δ : 0.03 max.
IR :More than 10,000 ㏁ or 500 ㏁×㎌Initial Measurement 2*
Whichever is smaller Final Measurement 3*
Temperature Cycling Appearance : No abnormal exterior appearance 1,000Cycles
Capacitance Change Within ±10 % Initial Measurement 2*
Tan δ : 0.03 max. Final Measurement 3*
IR :More than 10,000 ㏁ or 500 ㏁×㎌Measurement at 24±2hrs after test conclusion
Whichever is smaller 1 cycle condition : -55+0/-3℃(30±3min) → Room Temp. (1min)
→ 125+3/-0℃(30±3min) → Room Temp. (1min)
Destructive Physical No Defects or abnormalities Per EIA 469
Analysis
Humidity Bias Appearance : No abnormal exterior appearance 1,000hrs 85℃/85%RH, Rated Voltage and 1.3~1.5V,
Capacitance Change Within ±12.5 % Add 100kohm resistor
Tan δ : 0.035 max. Initial Measurement 2*
IR :More than 500 ㏁ or 25 ㏁×㎌Final Measurement 4*
Whichever is smaller Measurement at 24±2hrs after test conclusion
The charge/discharge current is less than 50mA.
High Temperature Appearance : No abnormal exterior appearance 1,000hrs @ 125℃, 200% Rated Voltage,
Operating Life Capacitance Change Within ±12.5 % Initial Measurement 2*
Tan δ : 0.035 max. Final Measurement 4*
IR :More than 1,000 ㏁ or 50 ㏁×㎌Measurement at 24±2hrs after test conclusion
Whichever is smaller The charge/discharge current is less than 50mA.
Specificati o n of Automotive MLCC
(Reference sheet)
104
L
W
T
● Samsung P/N :
● Description :
0.50±0.30 mmBW
Size 1206 inch
3.20±0.15 mm
1.60±0.15 mm
1.15±0.10 mm
X7R
Performance Test condition
50
④
1206
100
External Visual No abnormal exterior appearance Microscope (´10)
Physical Dimension
s
Within the specified dimensions Using The calipers
Mechanical Shock Appearance : No abnormal exterior appearance Three shocks in each direction should be applied along
Capacitance Change Within ±10 % 3 mutually perpendicular axes of the test specimen (18 shocks)
Tan δ, IR : Initial spec.
Initial Measurement 2*
Final Measurement 5*
Vibration Appearance : No abnormal exterior appearance 5g's for 20min., 12cycles each of 3 orientations,
Capacitance Change Within ±10 % Use 8"×5" PCB 0.031" Thick 7 secure points on one long side
Tan δ, IR : Initial spec. and 2 secure points at corners of opposite sides. Parts mounted
within 2" from any secure point. Test from 10~2,000㎐.
Initial Measurement 2*
Final Measurement 5*
Resistance to Appearance : No abnormal exterior appearance preheating : 150℃ for 60~120 sec.
Solder Heat Capacitance Change Within ±10 % Solder pot : 260±5℃, 10±1sec.
Tan δ, IR : Initial spec. Initial Measurement 2*
Final Measurement 3*
ESD Appearance : No abnormal exterior appearance AEC-Q200-002 or ISO/DIS10605
Capacitance Change Within ±10 % Initial Measurement 2*
Tan δ, IR : Initial spec. Final Measurement 4*
Solderability 95% of the terminations is to be soldered a) Preheat at 155℃ for 4 hours, Immerse in solder for 5s at 245±5℃
evenly and continuously b) Steam aging for 8 hours, Immerse in solder for 5s at 245±5℃
c) Steam aging for 8 hours, Immerse in solder for 120s at 260±5℃
solder : a solution ethanol and rosin
Electrical Capacitance : Within specified tolerance *A capacitor prior to measuring the capacitance is heat treated at
Characterization Tan δ
:
0.025 max. 150 +0/-10℃ for 1hour and maintained in ambient air for 24±2 hours
IR(25℃) : More than 10,000 ㏁ or 500 ㏁×㎌The Capacitance / D.F. should be measured at 25℃,
Whichever is smaller 1 ㎑ ± 10%, 1 ± 0.2 Vrms
IR(125℃) More than 1,000 ㏁ or 10 ㏁×㎌I.R. should be measured with a DC voltage not exceeding
Whichever is smaller Rated Voltage @25℃, @125℃ for 60~120 sec.
Dielectric Strength Dielectric Strength : 250% of the rated voltage for 1~5 seconds
Board Fl e x Appearance : No abnormal exterior appearance Bending to the limit, 2 ㎜ for 60 seconds 1*
Capacitance Change Within ±10 % Initial Measurement 2*
Final Measurement 5*
Terminal Appearance : No abnormal exterior appearance 18 N, for 60 sec.
Strength(SMD) Capacitance Change Within ±10 % Initial Measurement 2*
Final Measurement 5*
Beam Load Destruction value should be exceed 15 N Beam speed : 2.5±0.25 ㎜/sec
Temperature X7R
Characteristics From -55 ℃ to 125 ℃, Capacitance change should be within ±15%
D. Recom m e nde d S olderi ng m e t hod :
Reflow ( Reflow Peak Temperature : 260 +0/-5℃, 30sec. ), Meet IPC/JEDEC J-STD-020 D Standard
*1 : The figure indicates typical specification. Please refer to individual specifications.
*2 : Initial measurement : Perform a heat treatment at 150 +0/-10℃ for one hour after soldering process.
and then let sit for 24±2 hours at room temperature. Perform the initial measurement.
*3 : Final measurement : Let sit for 24±2 hours at room temperature after test conclusion, then measure.
*4 : Final measurement : Perform a heat treatment at 150 +0/-10℃ for one hour after soldering process.
and then let sit for 24±2 hours at room temperature. Perform the initial measurement.
*5 : Final measurement : Let measure within 24 hours at room temperature after test conclusion.
Product specifications included in the specifications are effective as of March 1, 2013.
Please be advised that they are standard product specifications for reference only.
We may change, modify or discontinue the product specifications without notice at any time.
So, you need to approve the product specifications before placing an order.
Should you have any question regarding the product specifications, please contact our sales personnel or application engineers.
0.5ms Half sine 4.7m/sec
Performance Test condition
Peak value Duration Wave Velocity
1,500G
● Disclaimer & Limitation of Use and Application
The products listed in this Specification sheet are NOT designed and manufactured for any use
and applications set forth below.
Please note that any misuse of the products deviating from products specifications or information
provided in this Spec sheet may cause serious property damages or personal injury.
We will NOT be liable for any damages resulting from any misuse of the products, specifically
including using the products for high reliability applications as listed below.
If you have any questions regarding this 'Limitation of Use and Application', you should first contact
our sales personnel or application engineers.
①
Aerospace/Aviation equipment
②
Medical equipment
③
Military equipment
④
Disaster prevention/crime prevention equipment
⑤
Power plant control equipment
⑥
Atomic energy-related equipment
⑦
Undersea equipment
⑧
Traffic signal equipment
⑨
Data-processing equipment
⑩
Electric heating apparatus, burning equipment
⑪
Safety equipment
⑫
Any other applications with the same as or similar complexity or reliability to the applications
