SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE Note.6
CURRENT ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME Note.8
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(Typ.)
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
LEAKAGE CURRENT
SAFETY STANDARDS Note.7
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT Note.4
OVER VOLTAGE
OVER TEMPERATURE
Can be adjusted by internal potentiometer A type only
500ms, 80ms at full load 230VAC /115VAC
16ms/230VAC 16ms/115VAC at full load
90 ~ 305VAC 127 ~ 431VDC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
THD< 20% when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧
0.43A / 115VAC 0.24A / 230VAC 0.23A / 277VAC
<0.75mA / 277VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
-40 ~ +70 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
336.5K hrs min. MIL-HDBK-217F (25 )℃
171*61.5*36.8mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to "DRIVING METHODS OF LED MODULE".
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. A type only.
7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.
8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
10. Refer to warranty statement.
11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
0.73Kg; 20pcs/15.6Kg/0.9CUFT
Protection type : Shut down o/p voltage, re-power on to recover
40W Single Output Switching Power Supply
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67 / IP65 design for indoor or outdoor installations
Class 2 power unit
Three in one dimming function (1~10Vdc or PWM signal or resistance)
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
5 years warranty (Note.10)
■ Features :
HLG-40H series
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, re-power on to recover
SELV
IP65 IP67
Blank : IP67 rated. Cable for I/O connection.
FMM
110
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
CONSTANT CURRENT REGION Note.4
HLG-40H-12 A
A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance
18 ~ 24V15 ~ 21V 23 ~ 30V 28 ~ 35V 35 ~ 43V 41 ~ 49V 48 ~ 58V 59 ~ 68V
54 ~ 65V
86.5% 86.5% 88% 88% 88.5% 88.5% 89.5%88.5% 89.5%
±2.5%
2 ~ 3.33A
±2.0%
1.6 ~ 2.67A
±1.0%
1.2 ~ 2A
±1.0%
1 ~ 1.67A
±1.0%
0.8 ~ 1.34A
±1.0%
0.67 ~ 1.12A
±1.0%
0.5 ~ 0.84A
±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
±2.0% ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5%
±1.0%
0.45 ~ 0.75A
±0.5%
±0.5%
±1.0%
0.58 ~ 0.96A
±0.5%
±0.5%
12V
HLG-40H-12 HLG-40H-15 HLG-40H-20 HLG-40H-24 HLG-40H-30 HLG-40H-36 HLG-40H-42 HLG-40H-48 HLG-40H-54
7.2 ~12V
15V
9 ~ 15V
20V
12 ~ 20V
24V
14.4 ~ 24V
30V
18 ~ 30V
36V
21.6 ~ 36V
48V
28.8 ~ 48V
3.33A 2.67A 2A 1.67A 1.34A 1.12A 0.84A
39.96W 40.05W 40W 40.08W 40.2W 40.32W 40.32W
150mVp-p 150mVp-p
13.5 ~ 17V
150mVp-p
17 ~ 22V
200mVp-p
22 ~ 27V
200mVp-p
27 ~ 33V
200mVp-p
33 ~ 40V
300mVp-p
44 ~ 53V10.8 ~ 13.5V
54V
32.4 ~ 54V
0.75A
40.5W
300mVp-p
49 ~ 58V
42V
25.2 ~ 42V
0.96A
40.32W
200mVp-p
40 ~ 46V
Compliance to EN55015, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3≧
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 4KV), criteria A
EMC IMMUNITY
EMC EMISSION
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed
UL8750, CSA C22.2 No. 250.0-08 (except for 48V, 54V), EN61347-1, EN61347-2-13 independent, IP65 or IP67 approved ;
optional models for J61347-1, J61347-2-13 ; design refer to UL60950-1, TUV EN60950-1, EN60335-1
COLD START 50A(t =210 s measured at 50% I ) at 230VAC
width peak
12 units (circuit breaker of type B) / 20 units (circuit breaker of type C) at 230VAC
μ
( for 48V,54V only) ( except for 48V,54V ) ( Optional )
TOTAL HARMONIC DISTORTION
Bauar
Sicherheit
egel gema
tgepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os
D (optional) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
File Name:HLG-40H-SPEC 2015-05-11
Mechanical Specification Case No.957B Unit:mm
※IP67 rated. Cable for I/O connection.
※IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
(Can access by removing the rubber stopper on the case.)
300 20±
300 20±
FG (Green/Yellow)
FG (Green/Yellow)
SVT 18AWG 2C×
SVT 18AWG 2C×
SJTW 18AWG 3C×
SJTW 18AWG 3C×
AC/L(Brown)
AC/L(Brown)
AC/N(Blue)
AC/N(Blue)
ψ×4.2 4PL
ψ×4.2 4PL
300 20±
300 20±
-V(Black)
-V(Black)
+V(Red)
+V(Red)
Io Vo
ADJ
ADJ
9.6
9.6
11.9
11.9
147.2
147.2
171
171
61.5 61.5
46.5 46.5
32 32
73.6
73.6
※T case: Max. Case Temperature.
※T case: Max. Case Temperature.
30.75
30.75
Tcase
Tcase
300 20±
FG (Green/Yellow)
SJTW 18AWG 3C×
AC/L(Brown)
AC/N(Blue)
9.6
11.9 147.2
171
61.5
46.5
32
-V(Black)
+V(Red)
DIM-(White)
DIM+(Blue)
ψ×4.2 4PL
SVT 18AWG 2C×
300 20±
73.6
※T case: Max. Case Temperature.
30.75
UL 2517 18AWG 2C×
Tcase
36.8
36.8 36.8
40W Single Output Switching Power Supply HLG-40H series
A Type:(HLG-40H-_A)
Blank:(HLG-40H)
File Name:HLG-40H-SPEC 2015-05-11
B Type:(HLG-40H-_B)
Derating Curve Static Characteristics
INPUT VOLTAGE (V) 60Hz
90 100 125 135 145 155 165 175 180 200 230 305
100
90
80
70
60
50
40
LOAD (%)
Fosc : 100KHz
Block Diagram
230VAC
Input only
AMBIENT TEMPERATURE ( )℃
LOAD (%)
-40 -25 0-10 15 30 50 60 70
20
40
60
80
100
(HORIZONTAL)
DIM+
(B Type)
DIM-
DETECTION
PWM & PFC CIRCUIT
O.L.P.O.T.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
O.V.P.
&
O.L.P.
PFC
CIRCUIT
※IP67 rated. Timer dimming function, contact MEAN WELL for details.
D Type(option):(HLG-40H-_D)
300 20±
FG (Green/Yellow)
SVT 18AWG 2C×
SJTW 18AWG 3C×
AC/L(Brown)
AC/N(Blue)
ψ×4.2 4PL
300 20±
-V(Black)
+V(Red)
9.6
11.9 147.2
171
61.5
46.5
32
73.6
30.75
Tcase
36.8
※T case: Max. Case Temperature.
40W Single Output Switching Power Supply HLG-40H series
File Name:HLG-40H-SPEC 2015-05-11
70
72
74
76
78
80
82
84
86
88
90
92
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277VAC
230VAC
115VAC
0.85
0.86
0.87
0.88
0.89
0.9
0.91
0.92
0.93
0.94
0.95
0.96
0.97
0.98
0.99
1
50% 60% 70% 80% 90% 100%
277VAC
230VAC
115VAC
HLG-40H series possess superior working efficiency that up to 89.5% can be reached in field applications.
EFFICIENCY vs LOAD (48V Model)
There are two major kinds of LED drive method "direct drive" and "with LED driver".
A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs.
Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
DRIVING METHODS OF LED MODULE
Power Factor Characteristic
LOAD
EFFICIENCY (%) PF
LOAD
Constant Current Mode
(40W)
Typical LED power supply I-V curve
Vo(%)
100
60
50 100
(min.)
Io (%)
Constant
Current area
Hiccup
Protection
Constant
Voltage area
(A) (B)
(C)
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
40W Single Output Switching Power Supply HLG-40H series
File Name:HLG-40H-SPEC 2015-05-11
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
-V(Black)
+V(Red)
DIM-(White)
DIM+(Blue)
HLG-40H
60KΩ
60%
60%
10KΩ
10K /NΩ20K /NΩ30K /NΩ40K /NΩ50K /NΩ60K /NΩ70K /NΩ80K /NΩ90K /NΩ
100K /NΩ
Single driver
Multiple drivers
(N=driver quantity for synchronized
dimming operation)
1V 4V 7V2V 5V 8V3V 6V 9V 10V
10%
10%
20KΩ
20%
20%
30KΩ
30%
30%
40KΩ
40%
40%
50KΩ
50%
50%
70KΩ
70%
70%
80KΩ
80%
80%
90KΩ100KΩOPEN
OPEN
OPEN
90%
90%
100%
100%
Resistance
value
Dimming value
Percentage of rated current
Percentage of rated current
※Reference resistance value for output current adjustment (Typical)
※Please DO NOT connect "DIM-" to "-V".
※1 ~ 10V dimming function for output current adjustment (Typical)
60%
60%
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
70%
70%
80%
80%
90%
90%
100%
100%
Duty value
Percentage of rated current
95%~108%
-----
95%~108%
95%~108%
※10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz
※Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or
1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-.
Dimming connection diagram for turning the lighting fixture ON/OFF :
Using a switch and relay can turn ON/OFF the lighting fixture.
※Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to
achieve 0% brightness of the lighting fixture connecting to the LED power supply unit.
※Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
1.Output constant current level can be adjusted through output cable by connecting a or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.resistance
2.The LED lighting fixture can be turned ON/OFF by the switch.
NFG L
Relay
Blue
Brown
Green/
Yellow AC/L
AC/N
HLG-40H
BType
DIM+
DIM-
V(-)
V(+)
Blue
White
Black
Red
Switch Adjuster
10K~100K Ohms resistance
1~10V DC Voltage
10V PWM Signal
LED Lighting Fixture
40W Single Output Switching Power Supply HLG-40H series
File Name:HLG-40H-SPEC 2015-05-11
DIMMING OPERATION (for B-type only)
◎Waterproof connector
Waterproof connector can be assembled on the output cable of HLG-40H to operate in dry/wet/damp or outdoor environment.
HLG-40H
I/P O/P
LED Lamp
AC
source
◎Cable Joiner
Pin Configuration (Female) Pin Configuration (Female)
Size Size
M12 M15
4-PIN
5A/PIN
M12-04Order No. Order No.
10A max.Suitable Current Suitable Current
5-PIN
5A/PIN
M12-05
10A max.
2-PIN
12A/PIN
M15-02
12A max.
Up to four wires can be connected through this cable joiner by
soldering or clamping by tools.
66
26 20
ψ25
O/P Wires
LED Lamp
HLG-40H
WATERPROOF CONNECTION
CJ04-2 suitable for 18AWG~22AWG
CJ04-1 suitable for 14AWG~16AWG
※CJ04 cable joiner can be purchased independently for user's own assembly.
MEAN WELL order No. : CJ04-1, CJ04-2.
40W Single Output Switching Power Supply HLG-40H series
File Name:HLG-40H-SPEC 2015-05-11
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Mean Well:
HLG-40H-12 HLG-40H-12A HLG-40H-12B HLG-40H-12D HLG-40H-15 HLG-40H-15A HLG-40H-15B HLG-40H-
15D HLG-40H-20 HLG-40H-20A HLG-40H-20B HLG-40H-20D HLG-40H-24 HLG-40H-24A HLG-40H-24B HLG-
40H-24D HLG-40H-30 HLG-40H-30A HLG-40H-30B HLG-40H-30D HLG-40H-36 HLG-40H-36A HLG-40H-36B
HLG-40H-36D HLG-40H-42 HLG-40H-42A HLG-40H-42B HLG-40H-42D HLG-40H-48 HLG-40H-48A HLG-40H-
48B HLG-40H-48D HLG-40H-54 HLG-40H-54A HLG-40H-54B HLG-40H-54D HLG-40H-12AB HLG-40H-24AB
HLG-40H-15AB HLG-40H-20AB HLG-40H-48AB HLG-40H-36AB HLG-40H-30AB HLG-40H-54AB HLG-40H-42AB
