SACC-DSI-M12FS-5CON-M16/0.5 - PHOENIX CONTACT

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page1/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's

documentation. Our General Terms of Use for Downloads are valid

(http://phoenixcontact.com/download)

Sensor/actuator flush-type socket, 5-pos., M12 SPEEDCON, A-coded, rear/screw mounting with M16 thread, with

0.5 m TPE litz wire, 5 x 0.34 mm²

Your advantages

Pre-assembled with litz wires for immediate use

Customer-specific assemblies and litz wire lengths available

Sealed on the litz wire side for optimum leak-tightness

All standard pin assignments and codings for signal, data, and power transmission with a uniform design-in design

For high transmission safety: shield connection to the housing with optional EMC nut

SPEEDCON fast locking system reduces cabling times

Key Commercial Data

Packing unit 1 pc

GTIN

GTIN 4046356533508

Weight per Piece (excluding packing) 20.000 g

Custom tariff number 85444290

Country of origin Germany

Technical data

Dimensions

Length of cable 0.5 m

Ambient conditions

Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket)

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page2/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Technical data

Ambient conditions

-25 °C ... 85 °C (Plug / socket)

Degree of protection IP67 (When plugged in)

IP65 (When plugged in)

General

Note

The electrical and mechanical data specified assume that the connector

pair is correctly locked and mounted. If the connector is unlocked and if

there is a danger of contamination, the connector must be sealed using

a protective cap > IP54. Influences arising from litz wires, cables or PCB

assembly must also be taken into consideration.

Rated current at 40°C 4 A

Rated voltage 60 V

Rated surge voltage 1.5 kV

Number of positions 5

Insulation resistance ≥ 100 MΩ

Coding A - standard

Standards/regulations M12 connector IEC61076-2-101

Signal type/category Universal

Status display No

Overvoltage category II

Degree of pollution 3

Connection method Individual wires

Insertion/withdrawal cycles > 100

Torque 3 Nm ... 4 Nm (Installation-side)

Mounting type Rear mounting M16 x 1.5 With flat nut

Thread type M16 x 1.5

Material

Flammability rating according to UL 94 V0

Contact material CuZn

Contact surface material Au

Contact carrier material PA 6.6

Material, knurls Zinc die-cast, nickel-plated

Sealing material FKM

Cable

Cable type TPE litz wire

Conductor cross section 0.34 mm²

AWG signal line 22

Conductor structure signal line 7x 0.25 mm

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page3/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Technical data

Cable

Core diameter including insulation 1.2 mm ±0.07mm

Thickness, insulation 0.21 mm

Wire colors Black, brown,blue, white, gray

Material conductor insulation TPE

Conductor material Tin-plated Cu litz wires

Standards/specifications M12 connector IEC61076-2-101

Insulation resistance ≥ 20 MΩ*km

Conductor resistance ≤ 57.6 mΩ/m

Nominal voltage, cable 300 V

Test voltage, cable 2000 VAC

Ambient temperature (operation) -40 °C ... 85 °C (cable, fixed installation)

-25 °C ... 85 °C (cable, flexible installation)

Standards and Regulations

Standards/specifications M12 connector IEC61076-2-101

Flammability rating according to UL 94 V0

Safety note

WARNING: The connectors may not be plugged in or disconnected under

load. Ignoring the warning or improper use may damage persons and/or

property.

• WARNING: Commission properly functioning products only. The products

must be regularly inspected for damage. Decommission defective products

immediately. Replace damaged products. Repairs are not possible.

• WARNING: Only electrically qualified personnel may install and operate

the product. They must observe the following safety notes. The qualified

personnel must be familiar with the basics of electrical engineering. They

must be able to recognize and prevent danger. The relevant symbol on the

packaging indicates that only personnel familiar with electrical engineering

are allowed to install and operate the product.

• The products are suitable for applications in plant, controller, and

electrical device engineering.

• When operating the connectors in outdoor applications, they must be

separately protected against environmental influences.

• Assembled products may not be manipulated or improperly opened.

• Only use mating connectors that are specified in the technical data of the

standards listed (e.g. the ones listed in the product accessories online at

phoenixcontact.com/products).

• When using the product in direct connection with third-party

manufacturers, the user is responsible.

• For operating voltages > 50V AC, conductive connector housings must

be grounded

• Ensure that when laying the cable, the tensile load on the connectors

does not exceed the upper limit specified in the standards.

• Observe the corresponding technical data. You will find information:

o On the product

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page4/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Technical data

Standards and Regulations

o On the packing label

o In the supplied documentation

o Online at phoenixcontact.com/products under the product

• Only use tools recommended by PhoenixContact

• Use a protective cap to protect connectors that are not in use. The

suitable accessories are available online in the accessory section of the

product at phoenixcontact.com/products

• Ensure that the protective or functional ground has been properly

connected.

• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are

applicable when combining several circuits in a cable and/or connector

• The connector warms up in normal operation. Depending on the ambient

conditions, the surface of the connector can continue to warm up. In

this case, the user is responsible for posting warnings (e.g. DIN EN ISO

13732-1:2008-12).

Environmental Product Compliance

REACh SVHC Lead 7439-92-1

China RoHS Environmentally Friendly Use Period = 50 years

For details about hazardous substances go to tab “Downloads”, Category

“Manufacturer's declaration”

Drawings

Dimensional drawing

19,6

≤4,5

7,6 500

M16x1,5

M12 flush-type socket

Circuit diagram

Contact assignment of the M12 socket

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page5/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Diagram

0 10 20 30 40 50 60 70 80 90 100 110 120 130

I [A]

[°C]

= 5x0,34mm2

I = current strength, T = ambient temperature

Dimensional drawing

Housing cutout for M16 fastening thread, mounting panel with thread

Dimensional drawing

Housing cutout for M16 fastening thread, mounting panel with feed-through hole (alternatively with area as anti-rotation protection for panel thicknesses

> 2 mm up to max. 4.5 mm)

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page6/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Schematic diagram

Pin assignment M12 socket, 5-pos., A-coded, socket side view

Classifications

eCl@ss

eCl@ss 10.0.1 27440102

eCl@ss 11.0 27440102

eCl@ss 4.0 27140800

eCl@ss 4.1 27140800

eCl@ss 5.0 27143400

eCl@ss 5.1 27143400

eCl@ss 6.0 27279200

eCl@ss 7.0 27440103

eCl@ss 9.0 27440102

ETIM

ETIM 2.0 EC001297

ETIM 3.0 EC002061

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page7/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Classifications

ETIM

ETIM 4.0 EC002061

ETIM 6.0 EC002061

UNSPSC

UNSPSC 6.01 31251501

UNSPSC 7.0901 31251501

UNSPSC 11 31251501

UNSPSC 12.01 31251501

UNSPSC 13.2 39121413

UNSPSC 18.0 39121413

UNSPSC 19.0 39121413

UNSPSC 20.0 39121413

UNSPSC 21.0 39121413

Approvals

UL Recognized / EAC / cULus Recognized

Ex Approvals

Approval details

UL Recognized http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 118976

 

Nominal voltage UN 60 V

Nominal current IN 4 A

mm²/AWG/kcmil 22

EAC  B.01687

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page8/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Approvals

cULus Recognized http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm E221474-20140616

 

Nominal voltage UN 60 V

Nominal current IN 4 A

mm²/AWG/kcmil 22-20

Accessories

Plug for cable screw gland

Screw plug-PROT-M12-1680539

An M12 screw plug for the unoccupied M12 sockets of the sensor/actuator cable, boxes and flush-type connectors



Screw plug-PROT-M12 SH-1503302

An M12 screw plug for the unoccupied M12 sockets of the shielded sensor/actuator cable, boxes and flush-type

connectors



Screw plug-PROT-M12 FB-1555538

M12 high-grade steel screw plug, for unoccupied M12 sockets of the sensor/actuator cables, boxes and flush-type

connectors for the food industry



Seal

https://www.phoenixcontact.com/us/products/1419658

03/28/2021Page9/9

Flush-type connector-SACC-DSI-M12FS-5CON-M16/0,5-1419658

Accessories

Flat gasket-SACC-M16-SEAL CLM-1430394

M16 flat gasket, for rear mounting of M12 flush-type connectors with M16 fastening thread



http://www.phoenixcontact.com