STANDARD
A
5962-90828
COLUMBUS, OHIO 43218-3990
E
4
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual i tem performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable devi ce class. The
manufactur er may el im inat e, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modi fication in the QM plan shall not
affect the form, fit, or function of the device for the applic abl e device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electr ica l performance characterist ic s. Unless otherwise specified herein, the el ectrical performance characteristics are
as specified in table I and shall appl y over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Mar king of dev ice( s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the dev ice described
herein shall m aintain the elec trical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type lis ted herein. Al s o, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certif i cate of compli an ce. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy ) sub mi tted to DLA Land and Maritime -VA s h all affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certif i cate of conform anc e. A certificate of c onformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircu its del iv ered t o this draw ing.
4. VERIFICATION
4.1 Sampling and i nspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quali ty Management (Q M) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test
circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1015 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.