MCR10EZHF3010 - Rohm Semiconductor

MCR10

Resistors

1/5

Thick film rectangular

MCR10 (2012 size : 1 / 8W)

!Features

1) Power rating of 1 / 8W

2) Highly reliable chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering

Thick film makes the electrodes very strong.

4) Leading the world in development and mass production.

Since start of production in 1982 (first in the wold), this component has established a solid reputation as a general–

purpose chip resistor.

5) ROHM resistors have approved ISO–9001 certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet before using or

ordering it.

!Ratings

0.125W (1 / 8W)

−55°C ∼ + 155°C

at 70°C

Item Conditions Specifications

Rated power

Rated voltage

Operating temperature

Nominal resistance

See Table 1.

Limiting element voltage 150V

100

−55 0 70 100 155

AMBIENT TEMPERATURE (°C)

POWER LOAD (%)

Fig.1

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

MCR10

Resistors

2/5

Max. 50mΩ

−55°C to +155°C

Resistance

Rated current

Operating temperature

Jumper type

F(±1%)

J (±5%)

10 ≤ R ≤ 2.2M (E24,96)

(E24)

±100

2.2 ≤ R < 10 ±500

1.0 ≤ R < 2.2 500±350

±200

10 ≤ R ≤ 10M

Table 1

Resistance tolerance Resistance range

(Ω)Resistance temperature coefficient

(ppm/°C)

0.15 ≤ R < 10 (E24) ±250

0.15 ≤ R < 1 (E24) ±250

0.1 ≤ R < 0.15 (E24) 400±200

!Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

!Characteristics

Item Test conditions (JIS C 5201-1)

Resistor type

Guaranteed value

Jumper type

Resistance

Variation of resistance

with temperature

Solderability

Damp heat, steady state

Endurance at 70°C

Endurance

Rapid change of

temperature

Bend strength of

the end face plating

Resistance to solvent

Resistance to

soldering heat

Overload ± (2.0%+0.1Ω) Max. 50mΩ

± (1.0%+0.05Ω)

± (3.0%+0.1Ω)

Max. 50mΩ

Max. 100mΩ

J : ±5%

F : ±1%

See Table.1

No remarkable abnormality on the appearance.

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Without mechanical damage such as breaks.

Max. 50mΩJIS C 5201-1 4.5

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

JIS C 5201-1 4.18

Soldering condition : 260±5

°C

Duration of immersion : 10±1s.

JIS C 5201-1 4.24

°C, 93%RH

Test time : 1,000h~1,048h

± (3.0%+0.1Ω)

± (1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70

°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h~1,048h

JIS C 5201-1 4.25.3

155

°C

Test time : 1,000h~1,048h

JIS C 5201-1 4.29

23±5

°C

, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.19

Test temp. : −55

°C

~+125

°C

5cyc

JIS C 5201-1 4.33

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum overload voltage : 200V

MCR10

Resistors

3/5

!External dimensions (Units : mm)

No. Material

Resistive element

(Oxide metal thick film)

Silver palladium thick film electrode

Nickel electrode

Sn/Pb or Sn electrode

Alumina substrate

Overcoating (glass)

0.4±0.2

1.25±0.1 0.55±0.1

0.4±0.2

2.0±0.1

!Packaging

0 2

0 4

0 6

0 8

0 2

0 4

0 6

0 8

ABD

ABCD

φ13±0.2

φD

110±0.7

12±0.1

Label

Reel Taping

Slider

Shutter

EIAJ ET-7201A compliant

Bulk case

EIAJ ET-7200A compliant

Thick paper

mount (Underside paper tape) Chip resistor Square punchout hole

Heat crimp cover/Tape

φ180 0

−3φ60 +1

09 +1.0

φ1.5 +0.1

1.65 +0.2

−0.1 2.4 +0.2

−0.1

36 0

−0.2

(Units: mm)

WFEA

8.0±0.3 3.5±0.05 1.75±0.1

4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1

(Units: mm)

MCR10

Resistors

4/5

!Part designation

MCR10 EZH

PZHI 5,000

10,000

F±1% ±5%J

Packaging / Processing specifications Resistance tolerance Special part number

Nominal resistancePart No.

3-digit or 4-digit IEC coding system

Part No.

Paper tape

Bulk case

Code Packaging

Standard ordering

Unit(pcs)

10Ω or more (F class)

1Ω or more (J class)

Blank

Up to10Ω (F class)

Up to1Ω (J class)

Specify "J" for jumper also.

!Dimensions

Fig.2 Dimensions (length)

1.80

1.85

1.90

1.95

2.00

2.05

2.10

2.15

2.20

RESISTANCE

(Ω)

LENGTH

(mm)

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

0.1 1 10 100 1k 10k 100k 1M 10M

Fig.3 Dimensions (width)

1.05

1.10

1.15

1.20

1.25

1.30

1.35

1.40

1.45

0.1 1 10 100 1k 10k 100k 1M 10M

RESISTANCE

(Ω)

WIDTH

(mm)

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

Fig.4 Dimensions (thickness)

0.35

0.40

0.45

0.50

0.55

0.60

0.65

0.70

0.75

0.1 1 10 100 1k 10k100k 1M 10M

RESISTANCE

(Ω)

THICKNESS

(mm)

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

!Electrical characteristics

Fig.5 Resistance

−8.0

−6.0

−4.0

−2.0

0.0

2.0

4.0

6.0

8.0

RESISTANCE

(Ω)

DC RESISTANCE

(%)

JIS C 5201-1 4.5

SAMPLE SIZE : n=20pcs

20°C 65%RH

0.1 1 10 100 1k 10k 100k 1M 10M

Fig.6 Variation resistance with

temperature

−900

−700

−500

−300

−100

100

300

500

700

900

RESISTANCE

(Ω)

TEMPERATURE COEFFICIENT (ppm/°C)

JIS C 5201-1 4.8

SAMPLE SIZE : n=10pcs

25°C / −55°C

25°C / 125°C

0.1 1 10 100 1k 10k 100k 1M 10M

Fig.7 Overload

−4.0

−3.0

−2.0

−1.0

0.0

1.0

2.0

3.0

4.0

RESISTANCE

(Ω)

∆R/R

(%)

JIS C 5201-1 4.13

SAMPLE SIZE : n=10pcs

RATED VOLTAGE×2.5

TIMES : 2s

MAXIMUM OVERLOAD VOLTAGE : 200V

0.1 1 10 100 1k 10k 100k 1M 10M

MCR10

Resistors

5/5

Fig.8 Resistance to soldering heat

RESISTANCE

(Ω)

∆R/R

(%)

JIS C 5201-1 4.18

SAMPLE SIZE : n=10pcs

SOLDERING CONDITION : 260°C 10s

0.1 1 10 100 1k 10k 100k1M 10M

−2.5

−2.0

−1.5

−1.0

−0.5

0.0

0.5

1.0

1.5

2.5

2.0

−2.5

−2.0

−1.5

−1.0

−0.5

0.0

0.5

1.0

1.5

2.5

2.0

0.1 1 10 100 1k 10k 100k1M 10M

Fig.9 Rapid change of

temperature

RESISTANCE

(Ω)

∆R/R (%)

JIS C 5201-1 4.19

SAMPLE SIZE : n=10pcs

−55°C / 125°C 5cyc

Fig.10 Damp heat, steady state

−4.0

−3.0

−2.0

−1.0

0.0

1.0

2.0

3.0

4.0

RESISTANCE (Ω)

∆R/R (%)

JIS C 5201-1 4.24

SAMPLE SIZE : n=10pcs

40°C 93%RH WITH NO LOAD 1,000h

0.1 1 10 100 1k 10k 100k 1M 10M

Fig.11 Endurance at 70°C

−4.0

−3.0

−2.0

−1.0

0.0

1.0

2.0

3.0

4.0

RESISTANCE (Ω)

∆R/R (%)

0.1 1 10 100 1k 10k 100k 1M 10M

JIS C 5201-1 4.25.1

SAMPLE SIZE : n=10pcs

70°C 1,000h

OVERLOAD : THE RATED VOLTAGE

Fig.12 Endurance

−4.0

−3.0

−2.0

−1.0

0.0

1.0

2.0

3.0

4.0

RESISTANCE

(Ω)

∆R/R

(%)

0.1 1 10 100 1k 10k 100k 1M 10M

JIS C 5201-1 4.25.3

SAMPLE SIZE : n=10pcs

155°C WITH NO LOAD 1,000h

Fig.13 Resistance to solvents

−2.0

−1.5

−1.0

−0.5

0.0

0.5

1.0

1.5

2.0

RESISTANCE

(Ω)

∆R/R (%)

JIS C 5201-1 4.29

SAMPLE SIZE : n=10pcs

IPA, 5min.

0.1 1 10 100 1k 10k 100k 1M 10M

Fig.14 Bend strength of

the end face plating

RESISTANCE

(Ω)

∆R/R

(%)

0.1 1 10 100 1k 10k 100k 1M 10M

−2.5

−2.0

−1.5

−1.0

−0.5

0.0

0.5

1.0

1.5

2.5

2.0

JIS C 5201-1 4.33

SAMPLE SIZE : n=10pcs

ENDURANCE WITH 90mm WIDTH