DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. REVISIONS LTR DESCRIPTION DATE (YR-M0-0A) APPROVED | A Add device type 03 for vendor CAGE number 93-01-12 M. A. Frye 65786. Add a reprogrammability test to 4.3.2. Change to margin test method A. Editorial changes throughout. REV SHEET REV SHEET REV STATUS REV A}TATaATAITATLaATaATaATLATaATaATA OF SHEETS SHEET 1/2};3 1415 | 6] 7 484 9 | 10} a1 | 12 PREPARED BY PMIC N/A Kenneth Rice DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 STANDARDIZED CHECKED BY MILITARY Ray Monnin DRAWING APPROVED bY MICROCIRCUIT, MEMORY, DIGITAL, CMOS - THIS DRAWING IS AVAILABLE Donald Cool 16K X 8 UV EPROM, POWER DOWN, FOR USE BY ALL DEPARTMENTS MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE Oa aa NO OVAL DATE SIZE CAGE CODE 5962-89538 AMSC N/A REVISION LEVEL A 67268 A SHEET 1 oF 12 4 DESC FORM 153 JUL 91 5962-3811. SCOPE 1.1 Scope. This drawing describes device requirements for class B microcircuits in accordance with 1.2.1 of MII -STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices". 1.2 Part_or_ Identifying Number (PIN). The complete PIN shall be as shown in the following example: 5962 -89538 OL Xe Se | | | | Drawing number Device type Case outline Lead finish per (1.2.1) (1.2.2) MIL -M-38510 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function Access time 01 CY7C254 16K x 8 UV EPROM 65 ns 02 CY7C254 16K x 8 UV EPROM 55 ns 03 CY7C254 16K x 8 UV EPROM 45 ns 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Qutline letter Descriptive designator Terminals Package style U CQCC1-N32 32 Rectangular leadiess chip carrier 1/ x GDIP1-T28 or CDIP2-T28 28 Dual-in-line 1/ Z GOFP2-F 28 28 Flat pack 1/ 1.2.3 Lead finish. The lead finish shal! be as specified in MIL-M-38510. Finish letter "X" shal} not be marked on the microcircuit or its packaging. The "X" designation is for use in specifications when lead finishes A, B, and C are considered acceptable and interchangeable without preference. 1.3 Absolute maximum ratings. Supply voltage range - - - - ----------+-- -0.5 V dc to +7.0 V dc DC voltage applied to Outputs in high Z- - - - - - - -0.5 V de to +7.0 V de DC input voltage - - ----------+--+--+-- -3.0 V de to +7.0 V dc Thermal resistance, junction-to-case (O5): Case outlines U, X, and Z ------------ See MIL-STD-1835 Maximum power dissipation (Pp) 2/--------- 1.0 W Maximum junction temperature (T)) - eee eee ee +175C Lead temperature (soldering, 10 seconds maximum) - - +260C Storage temperature range ------------- -65C to +150C Temperature under bias range - - ---------- -55C to +125C 1.4 Recommended operating conditions. Supply voltage (Vee) ec 4.5 V de to 5.5 V de High level input voltage (Vy )-----+------ 2.0 V dc minimum Low level input voltage (Vip - eee eee ee eee 0.8 V dc maximum Case operating temperature range (Te) - err eee -55C to +125C 1/ Lid shall be transparent to permit ultraviolet light erasure. 2/ Must withstand the added Pp due to short circuit test; e.g., Is: STANDARDIZED SIZE 5962-89538 MILITARY DRAWING A DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 REVISION LEVEL | SHEET A 2 DESC FORM 193A JUL 912. APPLICABLE DOCUMENTS 2.1 Government specification, standard, and bulletin. Unless otherwise specified, the following specification, standard, and bulletin of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIFICATION MILITARY MIL-M-38510 - Microcircuits, General Specification for. STANDARD MILITARY MIL-STD-883 - Test Methods and Procedures for Microelectronics. MIL-STD-1835 - Microcircuit Case Outlines. BULLETIN MILITARY MIL-BUL-103 - List of Standardized Military Drawings (SMD's). (Copies of the specification, standard, and bulletin required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with 1.2.1 of MIL-STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions sha!] be as specified in MIL-M-38510 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shat! be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing shall be as specified on figure 2. When required in groups A, B, or C inspection (see 4.3), the devices shall be programmed by the manufacturer prior to test in a checkerboard pattern or equivalent (a minimum of 50 percent of the total number of bits programmed) or to any altered item drawing pattern which includes at least 25 percent of the total number of bits programmed. 3.2.3.2 Programmed devices. The truth table for programmed devices shall be as specified by an attached altered item drawing. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table |. 3.5 Marking. Marking shall be in accordance with MIL-STD-883 (see 3.1 herein). The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-BUL-103 (see 6.6 herein). STANDARDIZED SIZE 5962-89538 MILITARY DRAWING A DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHTO 45444 REVISION LEVEL SHEET A 3 DESC FORM 193A JUL 91