Panel Mount DataSheet DUAL Series * Independently controlled dual output solid-state relay * Ratings from 25A to 40A @ 24-530 VAC * Industry standard package * SCR output for heavy industrial loads * DC Control * Zero-crossing (resistive loads) or random-fire (inductive loads) output PRODUCT SELECTION 25 A 40 A D2440D D2440DE 4-15 VDC Control D2425D D2425DE H12D4825D H12D4840D 15-32 VDC Control H12D4825DE H12D4840D Control Voltage 4-15 VDC Control 15-32 VDC Control AVAILABLE OPTIONS Thermal Pad Blank: Not Included H: Included Output Current 25: 25 Amps 40: 40 Amps Series H12D48 25 D Output Voltage D24: 24-280 VAC H12D48: 48-530 VAC H -10 Control Voltage D: 4-15 VDC DE: 15-32 VDC Switching Mode Blank: Zero Voltage Turn-On -10: Random Turn-On Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/sec] (3) Maximum Load Current [Arms] (4) Minimum Load Current [Arms] Maximum 1 Cycle Surge Current (50/60Hz) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (Rjc) [C/W] Maximum 1/2 Cycle It for Fusing (50/60 Hz) [A sec] Minimum Power Factor (with Maximum Load) D2425xx D2440xx H12D4825xx H12D4840xx 24-280 600 10 500 25 0.15 239/250 1.6 1.02 285/259 0.5 24-280 600 10 500 40 0.15 597/6250 1.6 0.63 1779/1621 0.5 48-530 1200 (2) 10 500 25 0.15 239/250 1.6 1.02 285/259 0.5 48-530 1200 (2) 10 500 40 0.15 597/625 1.6 0.63 1779/1621 0.5 FDE-07-01 REV. A Do not forget to visit us at: www.crydom.com Copyright (c) 2018 Crydom Inc. Specifications subject to change without notice. Panel Mount DataSheet INPUT SPECIFICATIONS (1) Description D24XXD H12D48XXD E-SUFFIX Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Typical Input Current @ 5 VDC (@ 24 VDC for E-Suffix) Nominal Input Impedance Maximum Turn-On Time [msec] (5) Maximum Turn-Off Time [msec] 4-15 VDC 4.0 VDC 1.0 VDC 13 mA 300 Ohm 1/2 Cycle 1/2 Cycle 4-15 VDC 4.0 VDC 1.0 VDC 13 mA 240 Ohm 1/2 Cycle 1/2 Cycle 15-32 VDC 15.0 VDC 1.0 VDC 15 mA 1500 Ohm 1/2 Cycle 1/2 Cycle GENERAL SPECIFICATIONS (1) Description Parameters Dielectric Strength, Input/Output (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) 4000 Vrms 109 Ohm 10 pF -40 to 80C -40 to 125 C 3.0 oz (86.5g) Thermally Conductive Epoxy .25" Fastons, .025" Square Pins Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Terminals GENERAL NOTES (1) All parameters at 25C unless otherwise specified. (2) For option (-10) models the Transient overvoltage is 1100Vac. (3) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (4) Heat sinking required, for derating curves see next page. (5) Turn-on time for random turn-on (-10) versions is 0.1 msec MECHANICAL SPECIFICATIONS Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 120/240V MODEL 1.17 (29.7) 1.00 (25.4) MOUNTING HOLE/SLOT 0.192 (4.9) DIA. FASTON TERMINAL .250 X .032 (4 PLACES) .73 (18.5) .45 (11.5) 1.78 (45.3) .250 x .032 FASTON TERMINAL (4 PLACES) 2.30 (58.4) 1.87 (47.5) PIN .025 SQ. .100 CENTERS 4 PLACES 0.60 (15.2) 480V MODEL .85 (21.6) 1.21 (30.6) 1.31 (33.2) Do not forget to visit us at: www.crydom.com Copyright (c) 2018 Crydom Inc. Specifications subject to change without notice. MOUNTING HOLE/SLOT .0192 (4.9) DIA. 2 PLC'S 1.87 (47.5) 2.30 (58.4) .77 (19.6) 1.37 (34.8) 1.80 (45.7) 1.60 (40.6) .187 x .032 FASTON TERMINAL (4 PLACES) .85 (21.6) 1.31 (33.2) Panel Mount DataSheet WIRING DIAGRAM 120/240Vrms 480Vrms A2 B1 A1 B2 LOAD A LOAD B LOAD B LOAD A 480Vrms 120/240Vrms A1 A2 B1 B2 240V Model 480V Model - B CONTROL + B CONTROL - A CONTROL + A CONTROL - A CONTROL + A CONTROL + B CONTROL - B CONTROL THERMAL DERATE INFORMATION DERATING CURVE: 40 A Dual SSR Combined Channel Output Current (Amps) 0.5 C/W 1.0 C/W 2.0 C/W 5.0 C/W 50 40 30 20 10 0 20 30 40 50 60 70 80 Combined Channel Output Current (Amps) DERATE CURVE: 25 AMP Dual SSR 0.5 C/W 1.0 C/W 1.5 C/W 2.0 C/W 80 70 60 50 40 30 20 10 0 20 30 40 50 60 70 80 Ambient Temperature (C) Ambient Temperature (C) AGENCY APPROVALS Agency Approvals Designed in accordance with the requirements of IEC 62314 E116949 (except 15-32VDC control) LR81689 (240 V, 4-15VDC control only) 5902 UG Rev. 101018 ECN#20564 Do not forget to visit us at: www.crydom.com Copyright (c) 2018 Crydom Inc. Specifications subject to change without notice. Panel Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. * Disconnect all power before installing or working with this equipment. * Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. * Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. * Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION * Eteindre toutes les sources d'energie de cet appareil avant de travailler dessus de cet appareil * Verifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lesions serieuses serieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. * Stellen Sie jeglichen Strom ab, der dieses Gerat versorgt, bevor Sie an dem Gerat Arbeiten durchfuhren * Vor dem Drehen auf Energie alle Anschlusse uberprufen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen konnen zum Tode oder zu schweren Verletzungen fuhren. RISCHIO DI SCOSSA ELETTRICA O DELL'ESPLOSIONE. * Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura * * Verificare tutti i collegamenti e sostituire tutte le coperture prima dell'accensione L'omissione di queste istruzioni provochera la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHADEN UND GEHAUSEERHITZUNG * The product's side panels may be hot, allow the product to cool before touching. * Follow proper mounting instructions including torque values. * Do not allow liquids or foreign objects to enter this product. * Les panneaux lateraux du produit peuvent etre chauds. Laisser le produit refroidir avant de le toucher. * Respecter les consignes de montage, et notamment les couples de serrage. * Ne pas laisser penetrer de liquide ni de corps etrangers a l'interieur du produit. * Die Seitenwande konnen hei sein. Lassen Sie das Produkt abkuhlen, bevor Sie es beruhren. * Beachten Sie die Montageanweisungen, * Fuhren Sie keine Flussigkeiten oder Fremdkorper in das Produkt ein. Le non-respect de cette directive peut entrainer, Failure to follow these instructions can result in des lesions corporelles graves ou des serious injury, or equipment damage. dommages materiels. Die Nichtbeachtung dieser Anweisung kann Korperverletzung oder Materialschaden zur Folge haben. RIESGO DE DANOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO * Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfrie antes de tocarlo. * Respetar las instrucciones de montaje, y en particular los pares de apretado. * No dejar que penetren liquidos o cuerpos extranos en el producto. * I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. * Seguire le istruzioni di montaggio corrette. * Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, danos materiales. La mancata osservanza di questa precauzione puo causare gravi rischi per l'incolumita personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright (c) 2018 Crydom Inc. Specifications subject to change without notice. * * * Panel Mount DataSheet ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People's Republic of China Electronic Industry Standard SJ/T11364 - 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder - SJ/T11364 - 2006, (Pb) (Hg) (Cd) (Cr (VI)) 50 Do not forget to visit us at: www.crydom.com Copyright (c) 2018 Crydom Inc. Specifications subject to change without notice. (PBB) (PBDE)