74HCT1G04GV,125 - NEXPERIA

1. General description

The 74HC1G04; 74HCT1 G04 is a single inverter. Inputs include clamp diodes that enable

the use of curren t lim it ing resis to rs to interfa c e inputs to voltages in excess of VCC.

2. Features and benefits

Wide supply voltage range from 2.0 V to 6.0 V

Input levels:

For 74HC1G04: CMOS level

For 74HCT1G04: TTL level

Symmetrical output impedance

High noise immunity

Low power dissipation

Balanced propagation delays

ESD protection:

HBM JESD22-A114E exceeds 2000 V

MM JESD22-A115 -A ex ce eds 20 0 V

Multiple package options

Specified from 40 C to +85 C and 40 C to +125 C

3. Ordering information

74HC1G04; 74HCT1G04

Inverter

Rev. 5 — 25 September 2013 Product data sheet

Table 1. Ordering information

Type number Package

Temperatur e ra nge Name Description Version

74HC1G04GW 40 C to +125 C TSSOP5 plastic thin shrink small outline package; 5 leads;

body width 1.25 mm SOT353-1

74HCT1G04GW

74HC1G04GV 40 C to +125 C SC-74A plastic surface-mounted package; 5 leads SOT753

74HCT1G04GV

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 2 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

4. Marking

[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.

5. Functional diagram

6. Pinning information

6.1 Pinning

6.2 Pin description

Table 2. Marking codes

Type number Marking[1]

74HC1G04GW HC

74HCT1G04GW TC

74HC1G04GV H04

74HCT1G04GV T04

Fig 1. Logic symbol Fig 2. IEC logic symbol Fig 3. Logic diagram

mna108

mna109

mna110

Fig 4. Pin configuration

74HC1G04

74HCT1G04

n.c. V

GND Y

001aaf089

Table 3. Pin de scription

Symbol Pin Description

n.c. 1 not connected

A 2 data input

GND 3 ground (0 V)

Y 4 data output

VCC 5 supply voltage

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 3 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

7. Functional description

8. Limiting values

[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

[2] Above 55 C, the value of Ptot derates linearly with 2.5 mW/K.

9. Recommended operating conditions

Table 4. Function table

H = HIGH voltage level; L = LOW voltage level

Input Output

A Y

Table 5. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). [1]

Symbol Parameter Conditions Min Max Unit

VCC supply voltage 0.5 +7.0 V

IIK input clamping current VI < 0.5 V or VI>V

CC + 0.5 V - 20 mA

IOK output clamping current VO<0.5 V or VO>V

CC + 0.5 V - 20 mA

IOoutput current 0.5 V < VO <V

CC +0.5V - 12.5 mA

ICC supply current - 25 mA

IGND ground current 25 - mA

Tstg storage temperature 65 +150 C

Ptot total power dissipation Tamb = 40 C to +125 C[2] - 200 mW

Table 6. Re commended operating conditions

Voltages are referenced to GND (ground = 0 V).

Symbol Parameter Conditions 74HC1G04 74HCT1G04 Unit

Min Typ Max Min Typ Max

VCC supply voltage 2.0 5.0 6.0 4.5 5.0 5.5 V

VIinput voltage 0 - VCC 0-V

CC V

VOoutput voltage 0 - VCC 0-V

CC V

Tamb ambient temperature 40 +25 +125 40 +25 +125 C

t/V input transition rise

and fall rate VCC = 2.0 V - - 625 - - - ns/V

VCC = 4.5 V - - 139 - - 139 ns/V

VCC = 6.0 V - - 83 - - - ns/V

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 4 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

10. Static characteristics

Table 7. Static characteristics

Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =25



Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit

Min Typ Max Min Max

For type 74HC1G04

VIH HIGH-level input

voltage VCC = 2.0 V 1.5 1.2 - 1.5 - V

VCC = 4.5 V 3.15 2.4 - 3.15 - V

VCC = 6.0 V 4.2 3.2 - 4.2 - V

VIL LOW-level input

voltage VCC = 2.0 V - 0.8 0.5 - 0.5 V

VCC = 4.5 V - 2.1 1.35 - 1.35 V

VCC = 6.0 V - 2.8 1.8 - 1.8 V

VOH HIGH-level output

voltage VI= VIH or VIL

IO= 20 A; VCC = 2.0 V 1.9 2.0 - 1.9 - V

IO= 20 A; VCC = 4.5 V 4.4 4.5 - 4.4 - V

IO= 20 A; VCC = 6.0 V 5.9 6.0 - 5.9 - V

IO= 2.0 mA; VCC = 4.5 V 4.13 4.32 - 3.7 - V

IO= 2.6 mA; VCC = 6.0 V 5.63 5.81 - 5.2 - V

VOL LOW-level output

voltage VI= VIH or VIL

IO= 20 A; VCC = 2.0 V - 0 0.1 - 0.1 V

IO= 20 A; VCC = 4.5 V - 0 0.1 - 0.1 V

IO= 20 A; VCC = 6.0 V - 0 0.1 - 0.1 V

IO= 2.0 mA; VCC = 4.5 V - 0.15 0.33 - 0.4 V

IO= 2.6 mA; VCC = 6.0 V - 0.16 0.33 - 0.4 V

IIinput leakage current VI=V

CC or GND; VCC = 6.0 V - - 1.0 - 1.0 A

ICC supply current VI=V

CC or GND; IO=0A;

VCC =6.0V --10 - 20A

CIinput capacitance - 1.5 - - - pF

For type 74HCT1G04

VIH HIGH-level input

voltage VCC = 4.5 V to 5.5 V 2.0 1.6 - 2.0 - V

VIL LOW-level input

voltage VCC = 4.5 V to 5.5 V - 1.2 0.8 - 0.8 V

VOH HIGH-level outp ut

voltage VI= VIH or VIL

IO= 20 A; VCC = 4.5 V 4.4 4.5 - 4.4 - V

IO= 2.0 mA; VCC = 4.5 V 4.13 4.32 - 3.7 - V

VOL LOW-level output

voltage VI= VIH or VIL

IO= 20 A; VCC = 4.5 V - 0 0.1 - 0.1 V

IO= 2.0 mA; VCC = 4.5 V - 0.15 0.33 - 0.4 V

IIinput leakage current VI=V

CC or GND; VCC = 5.5 V - - 1.0 - 1.0 A

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 5 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

11. Dynamic characteristics

[1] tpd is the same as tPLH and tPHL.

[2] CPD is used to determine the dynamic power dissipation PD(W).

PD=C

PD VCC2fi+(CLVCC2fo)where:

fi= input frequency in MHz

fo= output frequency in MHz

CL= output load capacitance in pF

VCC = supply voltage in Volts

(CLVCC2fo) = sum of outputs

ICC supply current VI=V

CC or GND; IO=0A;

VCC =5.5V --10 - 20A

ICC additional supply

current per input; VCC = 4.5 V to 5.5 V;

VI=V

CC 2.1 V; IO=0A - - 500 - 850 A

CIinput capacitance - 1.5 - - - pF

Table 7. Static characteristics …continued

Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =25



Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit

Min Typ Max Min Max

Table 8. Dynamic characteristics

GND = 0 V; tr = tf



6.0 ns; All typical values are measured at Tamb =25



C. For test circuit, see Figure 6

Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit

Min Typ Max Min Max

For type 74HC1G04

tpd propagation delay A to Y; see Figure 5 [1]

VCC = 2.0 V; CL= 50 pF - 25 105 - 135 ns

VCC = 4.5 V; CL=50pF - 9 21 - 27 ns

VCC = 5.0 V; CL=15pF - 7 - - - ns

VCC = 6.0 V; CL=50pF - 8 18 - 23 ns

CPD power dissipation

capacitance VI=GNDtoV

CC [2] -16- - -pF

For type 74HCT1G04

tpd propagation delay A to Y; see Figure 5 [1]

VCC = 4.5 V; CL=50pF - 10 24 - 27 ns

VCC = 5.0 V; CL=15pF - 8 - - - ns

CPD power dissipation

capacitance VI=GNDtoV

CC 1.5 V [2] -18- - -pF

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 6 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

12. Waveforms

Measurement points are given in Table 9.

Fig 5. The input (A) to output (Y) propagation delays

mna111

A input

Y output

tPHL tPLH

Table 9. Measur ement points

Type VIVM

74HC1G04 GND to VCC 0.5 VCC

74HCT1G04 GND to 03 V 1.3 V

Test data is given in Table 8. Definitions for test circuit:

RT = Termination resistance should be equal to output impedance Zo of the pulse generator

CL = Load capacitance including jig and probe capacitance

Fig 6. Load circuitry for switching times

mna101

RTCL

PULSE

GENERATOR DUT

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 7 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

13. Package outline

Fig 7. Package outline SOT353-1 (TSSOP5)

UNIT A1

max. A2A3bpLHELpwyv

ceD(1) E(1) Z(1) θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 0.1

01.0

0.8 0.30

0.15 0.25

0.08 2.25

1.85 1.35

1.15 0.65

1.3 2.25

2.0 0.60

0.15 7°

0°

0.1 0.10.30.425

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

0.46

0.21

SOT353-1 MO-203 SC-88A 00-09-01

03-02-19

0.15

(A3)

detail X

vMA

1.5 3 mm0

scale

TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1

1.1

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 8 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

Fig 8. Package outline SOT753 (SC-74A)

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT753 SC-74A

wBM

detail X

vMA

0 1 2 mm

scale

132

Plastic surface-mounted package; 5 leads SOT753

UNIT A1bpcDEHELpQywv

mm 0.100

0.013 0.40

0.25 3.1

2.7

0.26

0.10 1.7

1.3

0.95 3.0

2.5 0.2 0.10.2

DIMENSIONS (mm are the original dimensions)

0.6

0.2 0.33

0.23

1.1

0.9

02-04-16

06-03-16

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 9 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

14. Abbreviations

15. Revision history

Table 10. Abbreviations

Acronym Description

DUT Device Under Test

TTL Transistor-Transistor Logic

Table 11. Revision history

Document ID Release date Data sheet status Change notice Supersedes

74HC_HCT1G04 v.5 20130925 Product data sheet - 74HC_HCT1G04 v.4

Modifications: •Section 1 “General description” updated.

74HC_HCT1G04 v.4 20070716 Product data sheet - 74HC_HCT1G04 v.3

Modifications: •The format of this data sheet has been redesigned to comply with the new identity

guidelines of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

•Package SOT353 changed to SOT353-1 in Table 1 and Figure 7.

•Quick Reference Data and Soldering sections removed.

•Section 2 “Features and benefits” updated.

74HC_HCT1G04 v.3 20020517 Product specification - 74HC_HCT1G04 v.2

74HC_HCT1G04 v.2 20010302 Product specification - 74HC_HCT1G04 v.1

74HC_HCT1G04 v.1 19980831 Preliminary specification - -

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 10 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

16. Legal information

16.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of de vice(s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nexperia.com.

16.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. Nexperia does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and tit le. A short data sh eet is intended

for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local Nexperia sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall pre vail.

Product specificatio n — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

Nexperia and its customer, unless Nexperia and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the Nexperia product is

deemed to off er functions and qualities beyond those described in the

Product data sheet.

16.3 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, Nexperia does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information. Nexperia takes no

responsibility for the content in this document if provided by an inf ormation

source outside of Nexperia.

In no event shall Nexperia be liable for any indirect, incidental,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, Nexperia’s aggregate and cumulative liability towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of Nexperia.

Right to make changes — Nexperia reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — Nexperia products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where f ailure or

malfunction of a Nexperia product can reasonably be expected

to result in perso nal injury, death or severe property or environmental

damage. Nexperia and its suppliers accept no liability for

inclusion and/or use of Nexperia products in such equipment or

applications and ther efore such inclu sion and/or use is at the cu stomer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. Nexperia makes no

representation or warranty tha t such application s will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and ope ration of their applications

and products using Nexperia products, and Nexperia

accepts no liability for any assistance with applications or cust omer product

design. It is customer’s sole responsibility to determine whether the Nexperia

product is suitable and fit for the customer’s applications and

products planned, as well as fo r the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

Nexperia does not accept any liability related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by customer’s

third party customer(s). Customer is responsible for doing all necessary

testing for the customer’s applications and products using Nexperia

products in order to avoid a default of the applications and

the products or of the application or use by customer’s third part y

customer(s). Nexperia does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanent ly and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — Nexperia

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nexperia.com/profile/terms, unless otherwise

agreed in a valid written individua l agreement. In case an individual

agreement is concluded only the ter ms and conditions of the respective

agreement shall apply. Nexperia hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of Nexperia products by customer.

No offer to sell or license — Nothing i n this document may be interpreted or

construed as an of fer t o sell product s that is open for accept ance or t he grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the obj ective specification for product development.

Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.

Product [short] dat a sheet Production This document contains the product specification.

74HC_HCT1G04 All information provided in this document is subject to legal disclaimers.

Product data sheet Rev. 5 — 25 September 2013 11 of 12

Nexperia 74HC1G04; 74HCT1G04

Inverter

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific Nexperia product is automotive qualified,

the product is not suitable for automotive use. It i s neit her qualif ied nor tested

in accordance with automotive testing or application requirements. Nexperia

accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automot ive specifications and standard s, customer

(a) shall use the product without Nexperia’s warranty of the

product for such automotive applications, use and specifications, and (b)

whenever customer uses the product for automotive applications beyond

Nexperia’s specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies Nexperia for any

liability, damages or failed product claims resulting from custome r design and

use of the product for automotive applications beyond Nexperia’s

standard warranty and Nexperia’s product specifications.

Translations — A non-English (translated) version of a document is for

reference only. The English version shall prevail in case of any discrepancy

between the translated and English versions.

16.4 Trademarks

Notice: All referenced b rands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

17. Contact information

For more information, please visit: http://www.nexperia.com

For sales office addresses, please send an email to: salesaddresses@nexperia.com

Nexperia 74HC1G04; 74HCT1G04

Inverter

18. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1

3 Ordering information. . . . . . . . . . . . . . . . . . . . . 1

4 Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 2

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2

7 Functional description . . . . . . . . . . . . . . . . . . . 3

8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3

9 Recommended operating conditions. . . . . . . . 3

10 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4

11 Dynamic characteristics . . . . . . . . . . . . . . . . . . 5

12 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 7

14 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . 9

15 Revision history. . . . . . . . . . . . . . . . . . . . . . . . . 9

16 Legal information. . . . . . . . . . . . . . . . . . . . . . . 10

16.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 10

16.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

17 Contact information. . . . . . . . . . . . . . . . . . . . . 11

18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

For more information, please visit: http://www.nexperia.com

For sales office addresses, please send an email to: salesaddresses@nexperia.com

Date of release:

25 September 2013