FPLB54TEDS2-155.52MHZ - Connor-Winfield Corporation (The)

THE CONNOR-WINFIELD CORP.

2111 COMPREHENSIVE DRIVE.

AURORA, IL 60505.

FAX (630) 851-5040.

PHONE (630) 851-4722. PRODUCT DATA SHEET

Specifications subject to change without notice.

DATA SHEET #: REV: DATE:

CRYSTAL CONTROLLED OSCILLATORS

The Connor-Winfield FPLB54TED,

FPLB54TEDS1, F PLB54TEDS2

and FPLB54TEDS3 are Surface

Mount 3.3V Fixed Frequency

Crystal Oscillators (VCXO) with

selectable output frequencies and

Differential LVPECL outputs.

Based on an Inverted Mesa Crystal

design the FPLB54TED series are

designed for SONET/SDH Network

Timing Source requiring low jitter

and tight stability.

1 2

FPLB54TED - 155.52MHz

LVPECL

SERIES CENTER

FREQUENCY

FEATURES

DESCRIPTION

ORDERING INFORMATION

SELECTABLE OUTPUT:

FPLB54TED: 155.52MHz or 167.331MHz

FPLB54TEDS1: 155.52MHz or 166.6286MHz

FPLB54TEDS2: 155.52MHz or 156.25MHz

FPLD54TEDS3: 155.52MHz or 161.13281MHz

3.3V SUPPLY VOLTAGE

LOW JITTER <1pS RMS

FREQUENCY TOLERANCE ±20ppm

TEMPERATURE RANGE: 0 TO 70°C

DIFFERENTIAL LVPECL OUTPUTS

SURFACE MOUNT PACKAGE

TAPE AND REEL PACKAGING

3.3V SURFACE MOUNT LVPECL OSCILLATOR

FPLB54TED, FPLB54TEDS1,

FPLB54TEDS2, FPLB54TEDS3

Ec163 05 11/5/03

www.conwin.com

CW 0107

FPLB54TED

155.52M

Notes

1.0 Inclusive of calibration @ 25°C, frequency vs. temperature, supply and load variations, shock, vibration and aging for ten

years.

2.0 Output terminated into 50 ohms into Vcc – 2.0Vdc or Thevenin equivalent.

ABSOLUTE MAXIMUM RATINGS TABLE 1.0

PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS NOTE

Storage Temperature -40 - 85 °C

Supply Voltage (Vcc) -0.5 - 7.0 Vdc

MODEL SPECIFICATIONS: TABLE 2.0

MODEL FPLB54TED

Center Frequency: Output Select “1” (Fo) - 155.520 - MHz

Center Frequency: Output Select “0” (Fo) - 167.331 - MHz

MODEL FPLB54TEDS1

Center Frequency: Output Select “1” (Fo) - 155.5200 - MHz

Center Frequency: Output Select “0” (Fo) - 166.6286 - MHz

MODEL FPLB54TEDS2

Center Frequency: Output Select “1” (Fo) - 155.520 - MHz

Center Frequency: Output Select “0” (Fo) - 156.250 - MHz

MODEL FPLB54TEDS3

Center Frequency: Output Select “1” (Fo) - 155.520 - MHz

Center Frequency: Output Select “0” (Fo) - 161.13281 - MHz

OPERATING SPECIFICATIONS TABLE 3.0

PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE

Total Frequency Tolerance -20 - 20 ppm 1

Operating Temperature Range 0 - 70 °C

Supply Voltage (Vcc) 3.135 3.3 3.465 Vdc

Supply Current (Icc) - - 60 mA

Jitter (BW=10Hz to 20MHz) - - 5 ps rms

Jitter (BW=12kHz to 20MHz) - - 1 ps rms

SSB Phase Noise at 100Hz offset - -60 - dBc/Hz

SSB Phase Noise at 1KHz offset - -100 - dBc/Hz

SSB Phase Noise at 10KHz offset - -130 - dBc/Hz

SSB Phase Noise at 100KHz offset - -140 - dBc/Hz

INPUT CHARACTERISTICS TABLE 4.0

PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE

Enable Input Voltage (Low) (Vil) - - <30% Vcc Vdc

Disable Input Voltage (High) (Vih) >70% Vcc - - Vdc

Output “0” Select Voltage (Low) “0” - - <30% Vcc Vdc

Output “1” Select Voltage (High) “1” >70% Vcc - - Vdc

PECL OUTPUT CHARACTERISTICS TABLE 5.0

PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE

LOAD - - 50 Ohms 2

Voltage (High) (Voh) 2.275 - - Vdc

(Low) (Vol) - - 1.68 Vdc

Duty Cycle at 50% Level 45 50 55 %

Duty Cycle Skew - 5 20 pS

Rise / Fall Time 20% to 80% - - 1.0 nS

PACKAGE CHARACTERISTICS TABLE 6.0

Package Non-hermetic package consisting of an FR4 substrate with grounded metal

cover.

PROCESS RECOMMENDATIONS TABLE 7.0

Solder Reflow The component solder used internal to this device has a melting point of

221°C. The peak temperature inside the device should be less than or

equal to 220°C for a maximum of 10 seconds

Wash Ultrasonic cleaning is not recommended.