LM386N-1/NOPB - Texas Instruments

GAIN

15 k

150 1.35 k

15 k

50 k

3+ INPUT

VOUT

GND

- INPUT 2

50 k

BYPASS 7

Product

Folder

Order

Now

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

LM386 Low Voltage Audio Power Amplifier

1 Features

1• Battery Operation

• Minimum External Parts

• Wide Supply Voltage Range: 4 V–12 V or

5 V–18 V

• Low Quiescent Current Drain: 4 mA

• Voltage Gains from 20 to 200

• Ground-Referenced Input

• Self-Centering Output Quiescent Voltage

• Low Distortion: 0.2% (AV= 20, VS=6V,RL= 8 Ω,

PO= 125 mW, f = 1 kHz)

• Available in 8-Pin MSOP Package

2 Applications

• AM-FM Radio Amplifiers

• Portable Tape Player Amplifiers

• Intercoms

• TV Sound Systems

• Line Drivers

• Ultrasonic Drivers

• Small Servo Drivers

• Power Converters

3 Description

The LM386M-1 and LM386MX-1 are power amplifiers

designed for use in low voltage consumer

applications. The gain is internally set to 20 to keep

external part count low, but the addition of an external

resistor and capacitor between pins 1 and 8 will

increase the gain to any value from 20 to 200.

The inputs are ground referenced while the output

automatically biases to one-half the supply voltage.

The quiescent power drain is only 24 mW when

operating from a 6-V supply, making the LM386M-1

and LM386MX-1 ideal for battery operation.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LM386N-1 PDIP (8) 9.60 mm × 6.35 mm

LM386N-3 PDIP (8) 9.60 mm × 6.35 mm

LM386N-4 PDIP (8) 9.60 mm × 6.35 mm

LM386M-1 SOIC (8) 4.90 mm × 3.90 mm

LM386MX-1 SOIC (8) 4.90 mm × 3.90 mm

LM386MMX-1 VSSOP (8) 3.00 mm × 3.00 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

Schematic

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Pin Configuration and Functions......................... 3

6 Specifications......................................................... 3

6.1 Absolute Maximum Ratings ...................................... 3

6.2 ESD Ratings ............................................................ 3

6.3 Recommended Operating Conditions....................... 4

6.4 Thermal Information.................................................. 4

6.5 Electrical Characteristics........................................... 4

6.6 Typical Characteristics.............................................. 5

7 Parameter Measurement Information .................. 6

8 Detailed Description.............................................. 7

8.1 Overview................................................................... 7

8.2 Functional Block Diagram......................................... 7

8.3 Feature Description................................................... 7

8.4 Device Functional Modes.......................................... 7

9 Application and Implementation .......................... 8

9.1 Application Information.............................................. 8

9.2 Typical Application ................................................... 8

10 Power Supply Recommendations ..................... 15

11 Layout................................................................... 16

11.1 Layout Guidelines ................................................. 16

11.2 Layout Examples................................................... 16

12 Device and Documentation Support................. 18

12.1 Device Support...................................................... 18

12.2 Documentation Support ....................................... 18

12.3 Related Links ........................................................ 18

12.4 Receiving Notification of Documentation Updates 18

12.5 Community Resources.......................................... 18

12.6 Trademarks........................................................... 18

12.7 Electrostatic Discharge Caution............................ 18

12.8 Glossary................................................................ 18

13 Mechanical, Packaging, and Orderable

Information........................................................... 19

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision B (March 2017) to Revision C Page

• Changed devices LM386M-1/LM386MX-1 To: LM386 in the data sheet title........................................................................ 1

• Changed From: LM386N-4 To: Speaker Impedance in the Recommended Operating Conditions table.............................. 4

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 1.......................................................................... 8

• Changed kW To: kΩin the Gain Control section ................................................................................................................... 8

• Changed kW To: kΩin the Input Biasing section................................................................................................................... 9

• Changed Figure 11................................................................................................................................................................. 9

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 2........................................................................ 10

• Changed Figure 13............................................................................................................................................................... 10

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 3........................................................................ 11

• Changed Figure 15............................................................................................................................................................... 11

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 4........................................................................ 12

• Changed Figure 17............................................................................................................................................................... 12

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 5........................................................................ 13

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 6........................................................................ 14

• Changed Figure 21............................................................................................................................................................... 14

• Changed From: 5 Ωto 12 ΩTo: 5 V to 12 V for Supply Voltage in Table 7........................................................................ 15

• Changed Figure 23............................................................................................................................................................... 15

Changes from Revision A (May 2004) to Revision B Page

• Added LM386MX-1 device to the data sheet. ....................................................................................................................... 1

• Added Device Information, Application and Implementation, Power Supply Recommendation, Layout, and Device

and Documentation Support sections..................................................................................................................................... 1

• Inserted Functional Block Diagram......................................................................................................................................... 7

GAIN 1

- INPUT

+ INPUT

GND

GAIN

BYPASS

VOUT

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

5 Pin Configuration and Functions

D Package

8-Pin MSOP

Top View

Pin Functions

PIN TYPE DESCRIPTION

NAME NO.

GAIN 1 – Gain setting pin

–INPUT 2 I Inverting input

+INPUT 3 I Noninverting input

GND 4 P Ground reference

VOUT 5 O Output

VS6 P Power supply voltage

BYPASS 7 O Bypass decoupling path

GAIN 8 – Gain setting pin

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)

MIN MAX UNIT

Supply Voltage, VCC LM386N-1/-3, LM386M-1 15 V

LM386N-4 22

Package Dissipation LM386N 1.25 WLM386M 0.73

LM386MM-1 0.595

Input Voltage, VI–0.4 0.4 V

Storage temperature, Tstg –65 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±1000 V

Charged-device model (CDM), per JEDEC specification JESD22-

C101(2) ±1000

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT

VCC Supply Voltage 4 12 V

LM386N-4 5 18 V

Speaker Impedance 4 Ω

VI Analog input voltage –0.4 0.4 V

TA Operating free-air temperature 0 70 °C

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report.

6.4 Thermal Information

THERMAL METRIC(1) LM386 LM386 LM386

UNITD (SOIC) DGK (VSSOP) P (PDIP)

888

RθJA Junction-to-ambient thermal resistance 115.7 169.3 53.4 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 59.7 73.1 42.1 °C/W

RθJB Junction-to-board thermal resistance 56.2 100.2 30.6 °C/W

ψJT Junction-to-top characterization parameter 12.4 9.2 19.0 °C/W

ψJB Junction-to-board characterization parameter 55.6 99.1 50.5 °C/W

6.5 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VSOperating Supply Voltage LM386N-1, -3, LM386M-1, LM386MM-1 4 12 V

LM386N-4 5 18

IQQuiescent Current VS= 6 V, VIN = 0 4 8 mA

POUT Output Power

VS= 6 V, RL= 8 Ω, THD = 10%

(LM386N-1, LM386M-1, LM386MM-1) 250 325

VS= 9 V, RL= 8 Ω, THD = 10%

(LM386N-3) 500 700

VS= 16 V, RL= 32 Ω, THD = 10%

(LM386N-4) 700 100

AVVoltage Gain VS= 6 V, f = 1 kHz 26 dB

10 µF from Pin 1 to 8 46

BW Bandwidth VS= 6 V, Pins 1 and 8 Open 300 kHz

THD Total Harmonic Distortion VS= 6 V, RL= 8 Ω, POUT = 125 mW

f = 1 kHz, Pins 1 and 8 Open 0.2%

PSRR Power Supply Rejection Ratio VS= 6 V, f = 1 kHz, CBYPASS = 10 μF

Pins 1 and 8 Open, Referred to Output 50 dB

RIN Input Resistance 50 kΩ

IBIAS Input Bias Current VS= 6 V, Pins 2 and 3 Open 250 nA

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

6.6 Typical Characteristics

Figure 1. Supply Current vs Supply Voltage Figure 2. Power Supply Rejection vs Frequency

Figure 3. Output Voltage vs Supply Voltage Figure 4. Voltage Gain vs Frequency

Figure 5. Total Harmonic Distortion vs Frequency Figure 6. Total Harmonic Distortion vs Power Out

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

Typical Characteristics (continued)

Figure 7. Device Dissipation vs Output Power Figure 8. Device Dissipation vs Output Power

Figure 9. Device Dissipation vs Output Power

7 Parameter Measurement Information

All parameters are measured according to the conditions described in the Specifications section.

Gain

Circuitry

Bias

Circuitry

Bypass

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

8 Detailed Description

8.1 Overview

The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4

Ωto 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and

capacitor between pins 1 and 8. This device comes in three different 8-pin packages as PDIP, SOIC and VSSOP

to fit in different applications.

8.2 Functional Block Diagram

8.3 Feature Description

There is an internal 1.35-KΩresistor that sets the gain of this device to 20. The gain can be modified from 20 to

200. Detailed information about gain setting can be found in the Detailed Design Procedure section.

8.4 Device Functional Modes

As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain

setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be

placed between pins 1 and 5 to modify the gain and frequency response for specific applications.

VIN

10 k 3

0.05 µF

250 µF

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

Below are shown different setups that show how the LM386 can be implemented in a variety of applications.

9.2 Typical Application

9.2.1 LM386 with Gain = 20

Figure 10 shows the minimum part count application that can be implemented using LM386. Its gain is internally

set to 20.

Figure 10. LM386 with Gain = 20

9.2.1.1 Design Requirements

Table 1. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.1.2 Detailed Design Procedure

9.2.1.2.1 Gain Control

To make the LM386 a more versatile amplifier, two pins (1 and 8) are provided for gain control. With pins 1 and 8

open the 1.35-kΩresistor sets the gain at 20 (26 dB). If a capacitor is put from pin 1 to 8, bypassing the 1.35-kΩ

resistor, the gain will go up to 200 (46 dB). If a resistor is placed in series with the capacitor, the gain can be set

to any value from 20 to 200. Gain control can also be done by capacitively coupling a resistor (or FET) from pin 1

to ground.

Additional external components can be placed in parallel with the internal feedback resistors to tailor the gain and

frequency response for individual applications. For example, we can compensate poor speaker bass response by

frequency shaping the feedback path. This is done with a series RC from pin 1 to 5 (paralleling the internal

15-kΩresistor). For 6 dB effective bass boost: R ~= 15 kΩ, the lowest value for good stable operation is R = 10

kΩif pin 8 is open. If pins 1 and 8 are bypassed then R as low as 2 kΩcan be used. This restriction is because

the amplifier is only compensated for closed-loop gains greater than 9.

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

9.2.1.2.2 Input Biasing

The schematic shows that both inputs are biased to ground with a 50 kΩresistor. The base current of the input

transistors is about 250 nA, so the inputs are at about 12.5 mV when left open. If the dc source resistance driving

the LM386 is higher than 250 kΩit will contribute very little additional offset (about 2.5 mV at the input, 50 mV at

the output). If the dc source resistance is less than 10 kΩ, then shorting the unused input to ground will keep the

offset low (about 2.5 mV at the input, 50 mV at the output). For dc source resistances between these values we

can eliminate excess offset by putting a resistor from the unused input to ground, equal in value to the dc source

resistance. Of course all offset problems are eliminated if the input is capacitively coupled.

When using the LM386 with higher gains (bypassing the 1.35 kΩresistor between pins 1 and 8) it is necessary

to bypass the unused input, preventing degradation of gain and possible instabilities. This is done with a 0.1 μF

capacitor or a short to ground depending on the dc source resistance on the driven input.

9.2.1.3 Application Curve

Figure 11. Supply Current vs Supply Voltage

VIN

10 k 3

0.05 µF

250 µF

LM386

10 µF

BYPASS

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

9.2.2 LM386 with Gain = 200

Figure 12. LM386 with Gain = 200

9.2.2.1 Design Requirements

Table 2. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.2.2 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.2.3 Application Curve

Figure 13. Supply Current vs Supply Voltage

VIN

10 k 3

0.05 µF

250 µF

LM386

BYPASS

1.2 k

10 µF

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

9.2.3 LM386 with Gain = 50

Figure 14. LM386 with Gain = 50

9.2.3.1 Design Requirements

Table 3. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.3.2 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.3.3 Application Curve

Figure 15. Supply Current vs Supply Voltage

3 V ± 15mA 3

50 µF

LM386

10 µF

47 k

0.01 µF

BYPASS

390

0.05 µF

4.7 k

0.01 µF

ELDEMA

CF-S-2158

f = 1 kHz

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

9.2.4 Low Distortion Power Wienbridge Oscillator

Figure 16. Low Distortion Power Wienbridge Oscillator

9.2.4.1 Design Requirements

Table 4. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.4.2 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.4.3 Application Curve

Figure 17. Supply Current vs Supply Voltage

VIN

10 k 3

0.05 µF

250 µF

LM386

10 Ÿ

0.033 µF

10 k

BYPASS

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

9.2.5 LM386 with Bass Boost

Figure 18. LM386 with Bass Boost

9.2.5.1 Design Requirements

Table 5. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.5.2 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.5.3 Application Curve

Figure 19. Voltage Gain vs Frequency

10 k

LM386

1 k

50 µF

30 k

f = 1 kHz

0.1 µF

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

9.2.6 Square Wave Oscillator

Figure 20. Square Wave Oscillator

Table 6. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.6.1 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.6.2 Application Curve

Figure 21. Supply Current vs Supply Voltage

LM386

BYPASS

10 k

VOL

10 k C1

2200 pF

0.05 µF

10 µF

FROM

DETECTOR

8 Ÿ

SPEAKER

0.05 µF

250 µF

FERRITE

BEAD

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

9.2.7 AM Radio Power Amplifier

Figure 22. AM Radio Power Amplifier

9.2.7.1 Design Requirements

Table 7. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Load Impedance 4 Ωto 32 Ω

Supply Voltage 5 V to 12 V

9.2.7.2 Detailed Design Procedure

The Detailed Design Procedure can be found in the Detailed Design Procedure section.

9.2.7.3 Application Curve

Figure 23. Supply Current vs Supply Voltage

10 Power Supply Recommendations

The LM386 is specified for operation up to 12 V or 18 V. The power supply should be well regulated and the

voltage must be within the specified values. It is recommended to place a capacitor to GND close to the LM386

power supply pin.

OUTPUT

LM386 10

0.05uF

250uF

INPUT

Connection to ground plane Connection to power 5V

Top layer traces Top layer ground plane

OUTPUT

LM386 10

0.05uF

250uF

INPUT

Connection to ground plane Connection to power 5V

Top layer traces Top layer ground plane

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

11 Layout

11.1 Layout Guidelines

Place all required components as close as possible to the device. Use short traces for the output to the speaker

connection. Route the analog traces far from the digital signal traces and avoid crossing them.

11.2 Layout Examples

Figure 24. Layout Example for Minimum Parts Gain = 20 dB on PDIP package

Figure 25. Layout Example for Minimum Parts Gain = 20 dB on SOIC package

LM386

INPUT

OUTPUT

0.05uF

250uF

Connection to ground plane Connection to power 5V

Top layer traces Top layer ground plane

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

Layout Examples (continued)

Figure 26. Layout Example for Minimum Parts Gain = 20 dB on VSSOP package

LM386

SNAS545C –MAY 2004–REVISED MAY 2017

www.ti.com

Product Folder Links: LM386

12 Device and Documentation Support

12.1 Device Support

12.1.1 Development Support

12.2 Documentation Support

12.3 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to order now.

Table 8. Related Links

PARTS PRODUCT FOLDER ORDER NOW TECHNICAL

DOCUMENTS TOOLS &

SOFTWARE SUPPORT &

COMMUNITY

LM386M-1 Click here Click here Click here Click here Click here

LM386MX-1 Click here Click here Click here Click here Click here

12.4 Receiving Notification of Documentation Updates

To receive notification of documentation updates — go to the product folder for your device on ti.com. In the

upper right-hand corner, click the Alert me button to register and receive a weekly digest of product information

that has changed (if any). For change details, check the revision history of any revised document.

12.5 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

12.6 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.7 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12.8 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

LM386

www.ti.com

SNAS545C –MAY 2004–REVISED MAY 2017

Product Folder Links: LM386

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 21-Nov-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM386M-1 LIFEBUY SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM386

M-1

LM386M-1/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM386

M-1

LM386MMX-1/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 Z86

LM386MX-1/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM386

M-1

LM386N-1/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) CU SN | Call TI Level-1-NA-UNLIM 0 to 70 LM

386N-1

LM386N-3/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 LM

386N-3

LM386N-4/NOPB ACTIVE PDIP P 8 40 Green (RoHS

& no Sb/Br) CU SN | Call TI Level-1-NA-UNLIM 0 to 70 LM

386N-4

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

PACKAGE OPTION ADDENDUM

www.ti.com 21-Nov-2017

Addendum-Page 2

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM386MMX-1/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

LM386MX-1/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 26-May-2017

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM386MMX-1/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0

LM386MX-1/NOPB SOIC D 8 2500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 26-May-2017

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LM386M-1 LM386M-1/NOPB LM386MMX-1 LM386MMX-1/NOPB LM386MX-1 LM386MX-1/NOPB LM386N-

1/NOPB LM386N-3/NOPB LM386N-4/NOPB