www.fairchildsemi.com FAN2514, FAN2515 200 mA CMOS LDO Regulators with Fast Start Enable Features * * * * * * * * wide variety of external capacitors, and the compact SOT23-5 surface-mount package. In addition, the FAN2514/15 family offer the fast power-cycle time required in CDMA handset applications. The products offer significant improvements over older BiCMOS designs and are pin-compatible with many popular devices. The output is thermally protected against overload. Ultra Low Power Consumption Enable optimized for CDMA time slices 200 mV dropout voltage at 200 mA 50 A ground current at 200 mA Enable/Shutdown Control SOT23-5 package Thermal limiting 300 mA peak current The FAN2514 and FAN2515 devices are distinguished by the assignment of pin 4: Applications * * * * FAN2514: pin 4 - ADJ, allowing the user to adjust the output voltage over a wide range using an external voltage divider. Cellular Phones and accessories PDAs Portable cameras and video recorders Laptop, notebook and palmtop computers FAN2514-XX: pin 4 - BYP, to which a bypass capacitor may be connected for optimal noise performance. Output voltage is fixed, indicated by the suffix XX. Description The FAN2514/15 family of micropower low-dropout voltage regulators utilize CMOS technology to offer a new level of cost-effective performance in GSM, TDMA, and CDMA cellular handsets, Laptop and Notebook portable computers, and other portable devices. Features include extremely low power consumption and low shutdown current, low dropout voltage, exceptional loop stability able to accommodate a FAN2515-XX: pin 4 - ERR, a flag which indicates that the output voltage has dropped below the specified minimum due to a fault condition. The standard fixed output voltages available are 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 3.0V, and 3.3V. Custom output voltage are also available: please contact your local Fairchild Sales Office for information. Block Diagrams EN EN VIN VIN Bandgap Error Amplifier BYP Bandgap p VOUT Error Amplifier p VOUT ADJ Thermal Sense FAN2514 GND Thermal Sense EN FAN2514-XX VIN Bandgap GND ERR Error Amplifier p VOUT Thermal Sense GND FAN2515-XX REV. 1.0.2 9/24/01 PRODUCT SPECIFICATION FAN2514/FAN2515 Pin Assignments VIN 1 GND 2 EN 3 5 VOUT 4 ADJ/BYP/ERR Pin No. FAN2514 FAN2514-XX FAN2515-XX 1. VIN VIN VIN 2. GND GND GND 3. EN EN EN 4. ADJ BYP ERR 5. VOUT VOUT VOUT Pin Descriptions Pin Name Pin No. Type Pin Function Description ADJ 4 Input FAN2514 Adjust. Ratio of potential divider from VOUT to ADJ determines output voltage. BYP 4 Passive FAN2514-XX Bypass. Connect 470 pF capacitor for noise reduction. ERR 4 Open drain FAN2515-XX Error. Error flag output. 0: Output voltage < 95% of nominal. 1: Output voltage > 95% of nominal. EN 3 Digital Input Enable. 0: Shutdown VOUT. 1: Enable VOUT. VIN 1 Power in Voltage Input. Supply voltage input. VOUT 5 Power out Voltage Output. Regulated output voltage. GND 2 Power Ground. Functional Description Designed utilizing CMOS process technology, the FAN2514/15 family of products are carefully optimized for use in compact battery-powered devices, offering a unique combination of low power consumption, extremely low dropout voltages, high tolerance for a variety of output capacitors, and the ability to disable the output to less than 1A under user control. In the circuit, a difference amplifier controls the current through a series-pass P-Channel MOSFET, comparing the load voltage at the output with an onboard low-drift bandgap reference. The series resistance of the pass P-Channel MOSFET is approximately 1, resulting in an unusually low dropout voltage under load when compared to older bipolar pass-transistor designs. 2 Protection circuitry is provided onboard for overload conditions. In conditions where the device reaches temperatures exceeding the specified maximums, an onboard circuit shuts down the output, where it remains suspended until it has cooled before re-enabling. The user is also free to shut down the device using the Enable control pin at any time. Careful design of the output regulator amplifier assures loop stability over a wide range of ESR values in the external output capacitor. A wide range of values and types can be accomodated, allowing the user to select a capacitor meeting his space, cost, and performance requirements, and enjoy reliable operation over temperature, load, and tolerance variations. REV. 1.0.2 9/24/01 FAN2514/FAN2515 Depending on the model selected, a number of control and status functions are available to enhance the operation of the LDO regulator. An Enable pin, available on all devices, allows the user to shut down the regulator output to conserve power, reducing supply current to less than 1A. The adjustable-voltage versions of the device utilize pin 4 to connect to an external voltage divider which feeds back to the regulator error amplifier, thereby setting the voltage as desired. Two other functions are available at pin 4 in the fixed-voltage versions: in noise-sensitive applications, an external Bypass capacitor connection is provided that allows the user to achieve optimal noise performance at the output, while the Error output functions as a diagnostic flag to indicate that the output voltage has dropped more than 5% below the nominal fixed voltage. PRODUCT SPECIFICATION Bypass Capacitor (FAN2514 Only) In the fixed-voltage configuration, connecting a capacitor between the bypass pin and ground can significantly reduce noise on the output. Values ranging from 470pF to 10nF can be used, depending on the sensitivity to output noise in the application. At the high-impedance Bypass pin, care must be taken in the circuit layout to minimize noise pickup, and capacitors must be selected to minimize current loading (leakage). Noise pickup from external sources can be considerable. Leakage currents into the Bypass pin will directly affect regulator accuracy and should be kept as low as possible; thus, highquality ceramic and film types are recommended for their low leakage characteristics. Cost-sensitive applications not concerned with noise can omit this capacitor. Applications Information Control Functions External Capacitors - Selection The FAN2514/15 allows the user to utilize a wide variety of capacitors compared to other LDO products. An innovative design approach offers significantly reduced sensitivity to ESR (Effective Series Resistance), which degrades regulator loop stability in older designs. While the improvements featured in the FAN2514/15 family greatly simplify the design task, capacitor quality still must be considered if the designer is to achieve optimal circuit performance. In general, ceramic capacitors offer superior ESR performance, at a lower cost and a smaller case size than tantalums. Those with X7R or Y5Vdielectric offer the best temperature coefficient characteristics. The combination of tolerance and variation over temperature in some capacitor types can result in significant variations, resulting in unstable performance over rated conditions. Input Capacitor An input capacitor of 2.2F (nominal value) or greater, connected between the Input pin and Ground, located in close proximity to the device, will improve transient response and noise rejection. Higher values will offer superior input ripple rejection and transient response. An input capacitor is recommended when the input source, either a battery or a regulated AC voltage, is located far from the device. Any good quality ceramic, tantalum, or metal film capacitor will give acceptable performance, however tantalum capacitors with a surge current rating appropriate to the application must be selected to avoid catastrophic failure. Output Capacitor An output capacitor is required to maintain regulator loop stability. Unlike many other LDO regulators, the FAN2514/15 family of products are nearly insensitve to output capacitor ESR. Stable operation will be achieved with a wide variety of capacitors with ESR values ranging from 10m to 10 or more. Tantalum or aluminum electrolytic, or multilayer ceramic types can all be used. A nominal value of at least 1F is recommended. REV. 1.0.2 9/24/01 Enable Pin Applying a voltage of 0.8V or less at the Enable pin will disable the output, reducing the quiescent output current to less than 1A, while a voltage of 1.5V or greater will enable the device. If this shutdown function is not needed, the pin can simply be connected to the VIN pin. Allowing this pin to float will cause erratic operation. Error Flag (FAN2515 only) To indicate conditions such as input voltage dropout (low VIN), overheating, or overloading (excessive output current), the ERR pin indicates a fault condition. It is an open-drain output which is HIGH when the voltage at VOUT is greater than 95% of the nominal rated output voltage and LOW when VOUT is less than 95% or the rated output voltage, as specified in the error trip level characteristics. A logic pullup resistor of 100K is recommended at this output. The pin can be left disconnected if unused. Thermal Protection The FAN2514/15 is designed to supply high peak output currents of up to 1A for brief periods, however this output load will cause the device temperature to increase and exceed maximum ratings due to power dissipation. During output overload conditions, when the die temperature exceeds the shutdown limit temperature of 190C, onboard thermal protection will disable the output until the temperature drops below this limit, at which point the output is then re-enabled. During a thermal shutdown situation the user may assert the power-down function at the Enable pin, reducing power consumption to the minimum level IGND. 3 PRODUCT SPECIFICATION Thermal Characteristics The FAN2514/15 is designed to supply 200mA at the specified output voltage with an operating die (junction) temperature of up to 125C. Once the power dissipation and thermal resistance is known, the maximum junction temperature of the device can be calculated. While the power dissipation is calculated from known electrical parameters, the thermal resistance is a result of the thermal characteristics of the compact SOT23-5 surface-mount package and the surrounding PC Board copper to which it is mounted. The power dissipation is equal to the product of the input-tooutput voltage differential and the output current plus the ground current multiplied by the input voltage, or: P D = ( V IN - V OUT )I OUT + V IN I GND The ground pin current IGND can be found in the charts provided in the Electrical Characteristics section. The relationship describing the thermal behavior of the package is: T J ( max ) - T A P D ( max ) = ------------------------------- JA where TJ(max) is the maximum allowable junction temperature of the die, which is 125C, and TA is the ambient operating temperature. JA is dependent on the surrounding PC board layout and can be empirically obtained. While the JC (junction-to-case) of the SOT23-5 package is specified at 130C /W, the JA of the minimum PWB footprint will be at least 235C /W. This can be improved upon by providing a heat sink of surrounding copper ground on the PWB. Depending on the size of the copper area, the resulting JA can range from approximately 180C /W for one square inch to nearly 130C /W for 4 square inches. The addition of backside copper with through-holes, stiffeners, and other enhancements can also aid in reducing this value. The heat contributed by the dissipation of other devices located nearby must be included in design considerations. Once the limiting parameters in these two relationships have been determined, the design can be modified to ensure that the device remains within specified operating conditions. If overload conditions are not considered, it is possible for 4 FAN2514/FAN2515 the device to enter a thermal cycling loop, in which the circuit enters a shutdown condition, cools, re-enables, and then again overheats and shuts down repeatedly due to an unmanaged fault condition. Operation of Adjustable Version The adjustable version of the FAN2514/15 includes an input pin ADJ which allows the user to select an output voltage ranging from 1.8V to near VIN, using an external resistor divider. The voltage VADJ presented to the ADJ pin is fed to the onboard error amplifier which adjusts the output voltage until VADJ is equal to the onboard bandgap reference voltage of 1.3V(typ). The equation is: R upper V OUT = 1.3V x 1 + ---------------R lower The total value of the resistor chain should not exceed 250K total to keep the error amplifier biased during no-load conditions. Programming output voltages very near VIN need to allow for the magnitude and variation of the dropout voltage VDO over load, supply, and temperature variations. Note that the low-leakage FET input to the CMOS Error Amplifier induces no bias current error to the calculation. General PWB Layout Considerations To achieve the full performance of the device, careful circuit layout and grounding technique must be observed. Establishing a small local ground, to which the GND pin, the output and bypass capacitors are connected, is recommended, while the input capacitor should be grounded to the main ground plane. The quiet local ground is then routed back to the main ground plane using feedthrough vias. In general, the highfrequency compensation components (input, bypass, and output capacitors) should be located as close to the device as possible. The proximity of the output capacitor is especially important to achieve optimal noise compensation from the onboard error amplifier, especially during high load conditions. A large copper area in the local ground will provide the heat sinking discussed above when high power dissipation significantly increases the temperature of the device. Component-side copper provides significantly better thermal performance for this surface-mount device, compared to that obtained when using only copper planes on the underside. REV. 1.0.2 9/24/01 FAN2514/FAN2515 PRODUCT SPECIFICATION Absolute Maximum Ratings (beyond which the device may be damaged)1 Parameter Min Typ Max Unit 0 7 V 0 7 V 0 7 V Power Supply Voltages VIN (Measured to GND) Enable Input (EN) Applied voltage (Measured to GND)2 ERR Output Applied voltage (Measured to GND)2 Power Dissipation3 Internally limited Temperature Junction -65 Lead Soldering (5 seconds) Storage -65 4 Electrostatic Discharge 150 C 260 C 150 C 4 kV Notes: 1. Functional operation under any of these conditions is NOT implied. Performance and reliability are guaranteed only if Operating Conditions are not exceeded. 2. Applied voltage must be current limited to specified range. 3. Based upon thermally limited junction temperature: T J ( max ) - T A P D = ------------------------------ JA 4. Human Body Model is 4kV minimum using Mil Std. 883E, method 3015.7. Machine Model is 400V minimum using JEDEC method A115-A. Operating Conditions Parameter Min VIN Input Voltage VEN Enable Input Voltage VERR ERR Flag Voltage Nom 2.7 0 Units 7.0 V VIN V VIN V +125 C TJ Junction Temperature JA Thermal resistance 220 C/W JC Thermal resistance 130 C/W REV. 1.0.2 9/24/01 -40 Max 5 PRODUCT SPECIFICATION FAN2514/FAN2515 Electrical Characteristics Symbol Parameter Regulator VDO Drop Out Voltage Conditions IOUT = 100 A IOUT = 50 mA IOUT = 100 mA IOUT = 200 mA IOUT = 200 mA VO3 Output Voltage Accuracy IGND Ground Pin Current Protection Current Limit Shut-Down Current IGSD TSH Thermal Protection Shutdown Temperature ETL ERR Trip Level Enable Input VIL Logic Low Voltage VIH IIH II Min. Typ. Max. Units 0.5 30 60 110 2 50 80 130 200 2 60 mV mV mV mV mV % A 1 A C % -2 IOUT = 200 mA 35 Thermally Protected EN = 0V FAN2515 only Logic High Voltage Input Current High Input Current Low 150 90 95 99 0.4 2.0 1.2 1.4 0.1 0.1 V V A A Notes: 1. Unless otherwise stated, TA = 25C, VIN = VOUT + 1V, IOUT = 100A, VEN = VIN. 2. Bold values indicate -40C TJ 125C. 3. Accuracy specified for the fixed voltage versions only. The adjustable output version has a bandgap voltage range of 1.24V to 1.40V with a nominal value of 1.32V. Switching Characteristics Parameter Enable Input2 Conditions Min. Typ. Response time Error Flag (FAN2515-XX) Response time Max. Unit 500 sec 3 msec Notes: 1. Unless otherwise stated, TA = 25C, VIN = VOUT + 1V, IOUT = 100A, VIH > 2.0 V. 2. When using repeated cycling. Performance Characteristics Symbol VOUT/VIN VOUT/VOUT eN PSRR Parameter Line regulation Load regulation Output noise Power Supply Rejection Conditions VIN = (VOUT + 1) to 7V IOUT = 0.1 to 200mA 10Hz-1KHz COUT = 10F, CBYP = 0.01F >10KHz, COUT = 10F, CBYP = 0.01F 120 Hz, COUT = 10F, CBYP = 0.01F Min. Typ. 0.3 1 <7 Max. 2 Units % /V % V Hz <0.01 43 dB Notes: 1. Unless otherwise stated, TA = 25C, VIN = VOUT + 1V, IOUT = 100A, VIH > 2.0 V. 6 REV. 1.0.2 9/24/01 FAN2514/FAN2515 PRODUCT SPECIFICATION Typical Performance Characteristics Power Supply Rejection Ratio Power Supply Rejection Ratio 40 VIN = 4.0V VOUT = 3.0V 100 PSRR (dB) 60 40 IOUT = 100A COUT = 10F Cer. CBYP = 0.01F 20 20 0 10 100 1k 10k 100k 1M 10M Frequency (Hz) VIN = 4.0V 80 VOUT = 3.0V Power Supply Rejection Ratio 60 40 0 10 100 1k 10k 100k 1M 10M Frequency (Hz) Power Supply Rejection Ratio 100 IOUT = 200mA 80 COUT = 10F Cer. CBYP = 0.01F VIN = 4.0V VOUT = 3.0V 40 PSRR (dB) 60 20 60 70 60 VIN = 4.0V VOUT = 3.0V 40 IOUT = 100A 10mA 50 40 30 100mA 200mA 20 20 COUT = 1.0F Cer. 10 100 0 10 1k 10k 100k 1M 10M Frequency (Hz) 100 1k 10k 100k 1M 10M Frequency (Hz) 50 40 30 20 100mA 200mA COUT = 10F Cer. CBYP = 0.01F 10 0 3.1 3.6 Voltage (V) REV. 1.0.2 9/24/01 4.1 Ground Pin Current VIN = 4V VOUT = 3V 0.1 0.01 0.001 0.0001 10 4.1 40.00 1 Noise (V/ Hz) PSRR (dB) IOUT = 100A 3.6 Voltage (V) 10 70 10mA 3.1 Noise Performance Power Supply Rejection Ratio vs. Voltage 60 0 Quiescent Current (A) 0 10 1k 10k 100k 1M 10M Frequency (Hz) Power Supply Rejection Ratio vs. Voltage 100 IOUT = 100mA 80 COUT = 10F Cer. CBYP = 0.01F IOUT = 10mA COUT = 10F Cer. CBYP = 0.01F 20 PSRR (dB) PSRR (dB) 100 VIN = 4.0V 80 VOUT = 3.0V VIN = 4.0V VOUT = 3.0V 1k 10k 100k 1M 10M Frequency (Hz) Power Supply Rejection Ratio 100 IOUT = 200mA 80 COUT = 1.0F Cer. 100 0 10 100 1k 10k 100k 1M 10M Frequency (Hz) Power Supply Rejection Ratio 100 0 10 40 20 0 10 100 Power Supply Rejection Ratio 40 40 60 20 1k 10k 100k 1M 10M Frequency (Hz) 60 60 PSRR (dB) 0 10 VIN = 4.0V IOUT = 100mA 80 VOUT = 3.0V COUT = 1.0F Cer. PSRR (dB) 60 20 100 VIN = 4.0V IOUT = 10mA 80 VOUT = 3.0V COUT = 1.0F Cer. PSRR (dB) PSRR (dB) IOUT = 100A 80 COUT = 1.0F Cer. PSRR (dB) Power Supply Rejection Ratio 100 100 COUT = 1.0F CBYP = 0.01F I L = 10A 100 1k 10k 100k Frequency (Hz) 1M 38.00 36.00 34.00 32.00 30.00 0.1 10 100 1 Load Current (mA) 7 PRODUCT SPECIFICATION FAN2514/FAN2515 Typical Performance Characteristics (continued) Ground Pin Current 60.00 60.00 50.00 40.00 30.00 20.00 VOUT = 3V IOUT = 100A 10.00 0.00 3.0 4.0 5.0 6.0 Input Voltage (V) 50.00 40.00 30.00 20.00 VOUT = 3V IOUT = 300mA 10.00 0.00 3.0 7.0 Ground Pin Current 75 Quiescent Current (A) 70.00 Quiescent Current (A) Quiescent Current (A) Ground Pin Current 70.00 4.0 5.0 6.0 VIN = 4V VOUT = 3V IL = 100A 50 25 0 -40 7.0 0 Input Voltage (V) 40 80 Temperature (C) 125 Dropout Characteristics 3.5 Ground Pin Current Dropout Voltage VIN = 4V VOUT = 3V IL = 200mA 25 0 40 80 Temperature (C) 90.00 60.00 30.00 0.00 0.1 125 0.5 50 100 150 0.0 0.0 200 6 4 IL = 100A 0 40 80 Temperature (C) 125 5.0 4.0 3.05 100 0 -40 3.0 Output Voltage vs. Temperature 150 50 2.0 1.0 Input Voltage (V) 200 Dropout Voltage (mV) Dropout Voltage (mV) 1.0 Dropout Voltage 8 0 -40 ROUT = 20 1.5 Output Current (mA) Dropout Voltage 2 ROUT = 30K 2.0 Output Voltage (V) 0 -40 VOUT = 3V 2.5 120.00 Output Voltage (V) 50 3.0 150.00 Dropout Voltage (mV) Quiescent Current (A) 75 IL = 200mA 0 40 80 Temperature (C) 3 2.95 2.85 -40 125 VIN = 4V Typical 3V device IL = 100A 2.9 0 40 80 Temperature (C) 125 Functional Characteristics Shutdown Delay Disable Voltage (1V/div) Enable Voltage (1V/div) Enable Pin Delay Enable Disable Output Voltage (1V/div) Output Voltage (1V/div) VOUT Time (20s/div) 8 VOUT Time (20s/div) REV. 1.0.2 9/24/01 PRODUCT SPECIFICATION FAN2514/FAN2515 Mechanical Dimensions 5-Lead SOT-23-5 (S) Package Symbol A A1 B c D E e e1 H L Inches Millimeters Min. Max. Min. Max. .035 .000 .008 .003 .106 .059 .057 .006 .90 .00 .20 .08 2.70 1.50 1.45 .15 .020 .010 .122 .071 .037 BSC .075 BSC .087 .126 .004 .024 0 10 Notes: Notes 1. Package outline exclusive of mold flash & metal burr. 2. Package outline exclusive of solder plating. 3. EIAJ Ref Number SC-74A. .50 .25 3.10 1.80 .95 BSC 1.90 BSC 2.20 3.20 .10 .60 0 10 e B L E H e1 c D A A1 9 REV. 1.0.2 9/24/01 PRODUCT SPECIFICATION FAN2514/FAN2515 Ordering Information Product Number VOUT Pin 4 Function Package Marking FAN2514S FAN2514S25 Adj. Adjust AGA 2.5 Bypass AGE FAN2514S26 2.6 Bypass AGG FAN2514S27 2.7 Bypass AGJ FAN2514S28 2.8 Bypass AGM FAN2514S285 2.85 Bypass AGN FAN2514S30 3.0 Bypass AGW FAN2514S33 3.3 Bypass AG3 FAN2515S25 2.5 Error output AHE FAN2515S26 2.6 Error output AHG FAN2515S27 2.7 Error output AHJ FAN2515S28 2.8 Error output AHM FAN2515S285 2.85 Error output AHN FAN2515S30 3.0 Error output AHW FAN2515S33 3.3 Error output AH3 Tape and Reel Information Quantity Reel Size Width 3000 7" 8mm DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 9/24/01 0.0m 002 Stock#DS30002514 2001 Fairchild Semiconductor Corporation