AccessRunner ADSL Modem Device Set for PCI Applications Controller-less, Scalable, Discrete Multitone-based, G.dmt- and G.litecompliant, ADSL Modem Device Set for PCI Applications Conexant's AccessRunner ADSL modem device set is compliant with the full-rate ANSI T1.413 Issue 2 and ITU G.dmt (G.992.1) ADSL standards, and with the splitterless ITU G.lite (G.992.2) specification. This rate-adaptive solution is designed for controllerless PCI desktop applications and supports downstream data rates of up to 8 Mbps and upstream data rates of up to 1 Mbps. The device set takes advantage of the processing power available with most new computers by eliminating the need for a separate microcontroller, resulting in a cost-effective solution suitable for both G.dmt and G.lite applications. Host-based software provides support for current industry standards for PPP over AAL5 over ATM over ADSL and RFC 1483 for Windows 98 and Windows 2000. The device set, as shown in Figure 1, consists of four chips: * * * * PCI bus interface (AccessRunner P46 in a 176-pin TQFP) DMT-based data pump (AccessRunner 11627 in a 176-pin TQFP) Analog front end (AccessRunner 20431 in a 32-pin TQFP) Line driver (AccessRunner 20441 in a 16-pin SSOP or 32-pin TQFP) Features * Complete controller-less PCI ADSL solution * Compliant with ADSL standards - Full-rate ANSI T1.413 Issue 2 and ITU G.dmt (G.992.1) standards - Splitterless ITU G.lite (G.992.2) specification * DMT modulation and demodulation * Full-rate adaptive modem - Maximum downstream rate of 8 Mbps - Maximum upstream rate of 1 Mbps * Supports splitterless ADSL implementation * WAN mode support: PPP over AAL5/ATM over ADSL via Windows 98/2000 * LAN mode support: RFC 1483 via Windows 98/2000 * Compliant with PCI Local Bus Specification, Revision 2.2 * Compliant with PCI Bus Power Management Interface Specification, Version 1.0 * Tone detection for low power mode D20431 AFE Features PCI Bus HostBased ADSL Controller Software P46 PCI Bus Interface 176-pin TQFP 11627 ADSL DMT Data Pump 176-pin TQFP 20431 Analog Front End 32-pin TQFP 20441 Line Driver 16-pin TSSOP Telephone Line Figure 1. AccessRunner ADSL Modem for PCI Applications Data Sheet (Preliminary) * Receive signal path includes: - Integrated hybrid receiver circuit with programmable gain - High pass filtering and 27dB of Automatic Gain Control (AGC) to improve signal-to-echo ratio - 14-bit ADC * Transmit signal path includes: - 30dB of AGC for transmit power control - Low pass filtering to suppress noise in the receive band - 14-bit DAC Independent digital serial data and control * interfaces Low power tone detection mode. * Conexant Proprietary Information Doc. No.100394B October 19, 1999 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications ADSL (Asymmetric Digital Subscriber Line) is a transmission technology used to carry user data over a single twisted pair line from the Central Office to the customer premises. The downstream (Central Office to Customer Premises) direction typically supports a much higher data rate than the upstream or return (Customer Premises to Central Office) channel. This asymmetric nature lends itself to applications like remote LAN access, Internet access, and video delivery. The downstream data rates can go up to 8 Mbps. The upstream data rates can go up to 1 Mbps. Actual data rates depend on the transceiver implementation, loop length, impairments, and transmitted power. The Conexant ADSL Modem Device Set for PCI Applications is based upon a scalable architecture. This architecture will enable the device set to support an emerging set of ADSL specifications called G.lite. G.lite is expected to make it possible for telcos to deploy consumer-oriented, "always on" 1.5 Mbps Internet access services without the need for splitter equipment or wiring changes at the customer premises. D20441 Line Driver Features * Differential input and output line driver * Thermal shutdown capability * Line impedance matching during powerdown * Fixed differential gain 11627 ADSL DMT Data Pump Features * Low power (0.5W) consumption * DSP-based programmable ADSL data pump * No external Interleave RAM, 16 Kbytes built-in * Single 3.3V 5% power supply * Echo cancellation * Digital interface and rate buffering * ADSL framing * Forward Error Correction (FEC) encoding and decoding and interleaving * Constellation encoding/decoding * IFFT modulation and FFT demodulation * Transmit and receive signal digital filtering * Time domain equalization * Frequency domain equalization * Clock recovery * CRC and scrambling * Digital interface framing * ATM mode * Bit-synchronous mode Ordering Information Product Package Device Number AccessRunner P46 PCI Bus Interface 176-pin TQFP P46 AccessRunner 11627 ADSL Discrete Multitone (DMT) Data Pump 176-pin TQFP 11627 AccessRunner 20431 Analog Front End 32-pin TQFP 20431 AccessRunner 20441 Line Driver 16-pin SSOP 20441-12 32-pin TQFP 20441-11 Revision History Revision Date Comments A 07/09/99 Initial release B 10/19/99 Defined dash numbers and updated figures for 20441 line driver, changed document number from DSL015, A Information provided by Conexant Systems, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Conexant for its use, nor any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Conexant other than for circuitry embodied in Conexant products. Conexant reserves the right to change circuitry at any time without notice. This document is subject to change without notice. Conexant products are not designed or intended for use in life support appliances, devices, or systems where malfunction of a Conexant product can reasonably be expected to result in personal injury or death. Conexant customers using or selling Conexant products for use in such applications do so at their own risk and agree to fully indemnify Conexant for any damages resulting from such improper use or sale. Conexant, "What's Next in Communications Technologies", AccessRunner, LANfinity, and the Conexant logo, are trademarks of Conexant Systems, Inc. Product names or services listed in this publication are for identification purposes only, and may be trademarks or registered trademarks of their respective companies. All other marks mentioned herein are the property of their respective owners. (c)1999, Conexant Systems, Inc. All Rights Reserved 2 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner 11627 ADSL DMT Data Pump Detailed Description The 11627 DMT data pump is a T1.413 Issue 2 and G.992.1 compliant custom digital signal processing (DSP) chip built specifically for DMT ADSL transmission for use in ADSL modems. Brief descriptions of each functional block within the data pump are provided in the following sections; refer to Figure 2. P46 PCI Bus Interface The P46 PCI bus interface is the bridge device between the 11627 ADSL DMT data pump and the host computer. It provides the control, interface, and data manipulation for the 11627 data pump, the 20431 AFE, the 20441 line driver, and hybrid circuitry. It is compliant with the PCI Local Bus Specification, Revision 2.2 and PCI Bus Power Management Interface Specification, Version 1.0. ATM Transmission Convergence (TC) In the transmit direction, this block is in charge of embedding ATM cells into the serial data streams being fed into the digital interface. 20431 Analog Front End The 20431 AFE is designed for use in full-rate and G.lite (G.992.2) ADSL modems. The ADSL AFE interfaces with the transmit line driver (20441) and the hybrid receive circuitry on the analog side, and with the ADSL DMT data pump (11627) on the digital side. The receive section filters out the unwanted echo and boosts the wanted signal before performing an A/D conversion. The transmit section converts digital data to analog signals and performs a smoothing operation before presenting the signals to the line driver. In the receive direction, this block extracts the ATM cell boundaries from the serial data streams coming from the digital interface. To reduce traffic on the PCI bus, the TC block performs idle cell insertion in the transmit direction and idle cell deletion and header error correction in the receive direction. The 20431 is designed to operate from a 3.3V supply (nominal), assuming that it is regulated within 5%. The maximum allowable supply voltage is 3.6V. Digital Interface (DI) ATM TC DI Transmit Block PCI Controller (P46) AM EncoderDecoder Bit Parser and QAM Encoder FFT IFFT AFE Interface Transmit Filter DAC Intf EC DI Receive Block Microcontroller Interface QAM Decoder and Bit Parser FEQ FFT Time Domain Equalizer AFE (20431) ADC Intf DMT Data Pump (11627) DSL015002 Figure 2. AccessRunner 11627 DMT Data Pump Functional Block Diagram Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 3 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Digital Interface (DI) Analog Front End (AFE) Interface The DI Transmit Block performs the following functions: transmit data multiplexing and buffering, fast and interleave data stream framing, transmit data synchronization control, eoc/aoc insertion, CRC encoding, scrambling, FEC encoding, and data interleaving. The AFE Interface performs the following functions: transmit signal filtering, time domain equalization, and time domain signal power averaging, and echo cancellation (EC). The DI Receive Block performs the following functions: data de-interleaving, FEC decoding, descrambling, CRC check, receive data synchronization and receive clock generation, demultiplexing and buffering of receive data and receive eoc/aoc. The microcontroller interface enables the host computer via the PCI controller to set parameters to control DSP sequencing and to read/write coefficients or data. Microcontroller Interface 20441 Line Driver QAM Encoder/Decoder The 20441 line driver is designed for use in full-rate and G.lite (G.992.2) ADSL modems. It is optimized for ideal ADSL performance providing low noise, high bandwidth, and superior linearity. The 20441 line driver transmits a DMT modulated signal in the 25 - 132 kHz band. It operates from a single 5V TBD% supply, refer to Figure 3. The QAM Encoder/Decoder performs the following functions: constellation encoding, clock recovery, receive gain compensation, frequency domain equalization (FEQ), slicing, and constellation decoding. The block also performs other functions like frequency domain signal processing, signal power, error power averaging and computations related to frequency domain training. The driver is optimized for ADSL performance: it has a very low noise figure, high bandwidth and good linearity. FFT The FFT performs IFFT for modulation of the transmit symbol, and FFT for demodulation of the receive symbol. 248.4 OUTP_DRV + INP_DRV + 400 + INM_DRV 248.4 OUTM_DRV RBIAS Current Control Block ( Line Driver ) (20441) DSL015_003 Figure 3. AccessRunner 20441 Line Driver 4 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner P46 PCI Bus Interface Device Hardware Pins and Signals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 GND DP_RD# DP_CS# DP_D[15] DP_D[14] DP_D[13] VDD DP_D[12] DP_D[11] GND DP_D[10] DP_D[9] DP_D[8] DP_D[7] DP_D[6] VDD DP_D[5] DP_D[4] GND DP_D[3] DP_D[2] GND DP_D[1] DP_D[0] VDD EEPROM_CS EEPROM_CLK EEPROM_DOUT EEPROM_DIN VGG2 PCI_PME VDD PCI_AD[0] PCI_AD[1] GND PCI_AD[2] PCI_AD[3] VDD PCI_AD[4] PCI_AD[5] GND PCI_AD[6] PCI_AD[7] VDD VDD PCI_AD[24] PCI_CBE#[3] PCI_IDSEL GND PCI_AD[23] PCI_AD[22] VDD PCI_AD[21] PCI_AD[20] GND PCI_AD[19] PCI_AD[18] VDD PCI_AD[17] PCI_AD[16] GND PCI_AD[15] PCI_CBE#[2] VDD PCI_FRAME# PCI_IRDY# GND PCI_TRDY# PCI_DEVSEL# PCI_STOP# PCI_PERR# VDD PCI_SERR# PCI_PAR PCI_CBE#[1] GND PCI_AD[14] PCI_AD[13] VDD PCI_AD[12] PCI_AD[11] GND PCI_AD[10] PCI_AD[9] VDD PCI_AD[8] PCI_CBE#[0] GND 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 VDD GPIN0 GPIN1 GPIO[0] GPIO[1] GPIO[2] GND GPIO[3] GPIO[4] VDD GPIO[5] GPIO[6] GPIO[7] GPIO[8] GND TDI_GPIO[9] TMS_GPIO[10] VDD REFCLK TRSTN_GPIO[11] PCI_VPCIPREFER VDD TCK TDO GND PCI_INTA# PCI_RST# VDD PCI_CLK GND PCI_GNT# PCI_REQ# PCI_AD[31] VDD PCI_AD[30] PCI_AD[29] GND PCI_AD[28] PCI_AD[27] VGG1 VDD PCI_AD[26] PCI_AD[25] GND 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 GND SCANEN SCANMODE PCI_VPCIEN# PCI_VAUXEN# NC NC NC NC NC NC VDD PCI_VPCIDET PCI_VAUXDET GND DP_TCLKLS0 DP_TXSOC0 DP_TDATLS0 DP_RCLKAS0 VDD DP_RXSOC0 DP_RDATAS0 GND AFE_SCLK AFE_STB AFE_CTRLIN AFE_CTRLOUT AFE_WAKEUP DP_IRQ#[1] DP_IRQ#[0] VDD DP_A[9] DP_A[8] GND DP_A[7] DP_A[6] DP_A[5] DP_A[4] DP_A[3] DP_A[2] DP_A[1] DP_A[0] DP_WR# VDD The pin assignments for the P46 are shown in Figure 4 and listed in Table 1. The signals are defined in Table 2. DSL015004 Figure 4. P46 Pinout Diagram Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 5 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Table 1. P46 Pin Designations by Number Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal 1 VDD 45 VDD 89 VDD 133 VDD 2 GPIN0 46 PCI_AD[24] 90 PCI_AD[7] 134 DP_WR# 3 GPIN1 47 PCI_CBE#[3] 91 PCI_AD[6] 135 DP_A[0] 4 GPIO[0] 48 PCI_IDSEL 92 GND 136 DP_A[1] 5 GPIO[1] 49 GND 93 PCI_AD[5] 137 DP_A[2] 6 GPIO[2] 50 PCI_AD[23] 94 PCI_AD[4] 138 DP_A[3] 7 GND 51 PCI_AD[22] 95 VDD 139 DP_A[4] 8 GPIO[3] 52 VDD 96 PCI_AD[3] 140 DP_A[5] 9 GPIO[4] 53 PCI_AD[21] 97 PCI_AD[2] 141 DP_A[6] 10 VDD 54 PCI_AD[20] 98 GND 142 DP_A[7] 11 GPIO[5] 55 GND 99 PCI_AD[1] 143 GND 12 GPIO[6] 56 PCI_AD[19] 100 PCI_AD[0] 144 DP_A[8] 13 GPIO[7] 57 PCI_AD[18] 101 VDD 145 DP_A[9] 14 GPIO[8] 58 VDD 102 PCI_PME 146 VDD 15 GND 59 PCI_AD[17] 103 VGG2 147 DP_IRQ#[0] 16 TDI_GPIO[9] 60 PCI_AD[16] 104 EEPROM_DIN 148 DP_IRQ#[1] 17 TMS_GPIO[10] 61 GND 105 EEPROM_DOUT 149 AFE_WAKEUP 18 VDD 62 PCI_AD[15] 106 EEPROM_CLK 150 AFE_CTRLOUT 19 REFCLK 63 PCI_CBE#[2] 107 EEPROM_CS 151 AFE_CTRLIN 20 TRSTN_GPIO[11] 64 VDD 108 VDD 152 AFE_STB 21 PCI_VPCIPREFER 65 PCI_FRAME# 109 DP_D[0] 153 AFE_SCLK 22 VDD 66 PCI_IRDY# 110 DP_D[1] 154 GND 23 TCK 67 GND 111 GND 155 DP_RDATAS0 24 TDO 68 PCI_TRDY# 112 DP_D[2] 156 DP_RXSOC0 25 GND 69 PCI_DEVSEL# 113 DP_D[3] 157 VDD 26 PCI_INTA# 70 PCI_STOP# 114 GND 158 DP_RCLKAS0 27 PCI_RST# 71 PCI_PERR# 115 DP_D[4] 159 DP_TDATLS0 28 VDD 72 VDD 116 DP_D[5] 160 DP_TXSOC0 29 PCI_CLK 73 PCI_SERR# 117 VDD 161 DP_TCLKLS0 30 GND 74 PCI_PAR 118 DP_D[6] 162 GND 31 PCI_GNT# 75 PCI_CBE#[1] 119 DP_D[7] 163 PCI_VAUXDET 32 PCI_REQ# 76 GND 120 DP_D[8] 164 PCI_VPCIDET 33 PCI_AD[31] 77 PCI_AD[14] 121 DP_D[9] 165 VDD 34 VDD 78 PCI_AD[13] 122 DP_D[10] 166 NC 35 PCI_AD[30] 79 VDD 123 GND 167 NC 36 PCI_AD[29] 80 PCI_AD[12] 124 DP_D[11] 168 NC 37 GND 81 PCI_AD[11] 125 DP_D[12] 169 NC 38 PCI_AD[28] 82 GND 126 VDD 170 NC 39 PCI_AD[27] 83 PCI_AD[10] 127 DP_D[13] 171 NC 40 VGG1 84 PCI_AD[9] 128 DP_D[14] 172 PCI_VAUXEN# 41 VDD 85 VDD 129 DP_D[15] 173 PCI_VPCIEN# 42 PCI_AD[26] 86 PCI_AD[8] 130 DP_CS# 174 SCANMODE 43 PCI_AD[25] 87 PCI_CBE#[0] 131 DP_RD# 175 SCANEN 44 GND 88 GND 132 GND 176 GND 6 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner Table 2. P46 Pin Signals by Group 1 Pin Name I/O Description PCI_AD[31:0] I/O Address/Data PCI_CBE#[3:0] I/O Command/Byte Enables PCI_FRAME# I/O Frame PCI_IRDY# I/O Initiator Ready PCI_TRDY# I/O Target Ready PCI_PAR I/O Parity (Even) PCI_STOP# I/O Target Stop PCI_DEVSEL# I/O Target Response Device Select PCI_IDSEL I Unique Select for Configuration PCI_PERR# I/O Parity Error PCI_SERR# O System Error PCI INTERFACE PCI_REQ# O Master Request PCI_GNT# I Grant PCI_CLK I PCI clock PCI_RST# I (S) Reset PCI_INTA# O Interrupt A PCI_PME O PCI Power Management Event Signal ADSL DMT DATA PUMP (11627) SERIAL CHANNEL INTERFACE DP_RDATAS0 I Receive AS0/ATM0 Serial Data DP_RXSOC0 I Receive ATM0 Start of Cell DP_RCLKAS0 I Receive AS0/ATM0 Data Clock DP_TDATLS0 O Transmit LS0/ATM0 Serial Data DP_TXSOC0 O Transmit ATM0 Start of Cell DP_TCLKLS0 I Transmit LS0/ATM0 Data Clock ADSL DMT DATA PUMP (11627) MICRO INTERFACE DP_WR# O Data Pump Device Write Enable DP_RD# O Data Pump Device Read Enable DP_D[15:0] I/O (PU) Data Pump Data Lines DP_A[9:0] O Data Pump Address Lines DP_CS# O Data Pump Chip Select DP_IRQ#[1:0] I (PU,S) Data Pump Interrupt Request Lines AFE_SCLK I Serial AFE Clock AFE_STB O AFE Strobe ANALOG FRONT END INTERFACE 1 AFE_CTRLIN O Serial Data Sent to AFE AFE_CTRLOUT I Serial Data Received from AFE PD PU S Resistive pull-down Resistive pull-up Schmitt Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 7 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications 1 Pin Name I/O Description AFE_WAKEUP I (S) DSL Power Management Wakeup Signal from AFE EEPROM_CS O EEPROM Chip Select EEPROM_CLK O EEPROM Clock EEPROM_DIN I EEPROM Data Input EEPROM_DOUT O EEPROM Data Output SERIAL EEPROM PCI POWER MANAGEMENT PCI_VAUXDET I (PD,S) Vaux Detect PCI_VPCIDET I (PD,S) Vpci Detect PCI_VAUXEN# O Vaux Enable PCI_VPCIEN# O Vpci Enable PCI_VPCIPREFER I This pin is used to determine whether Vpci or Vaux is the preferred power supply. 1=Vpci preferred, 0=Vaux preferred GPIO[1:0] I/O (PU,S) General Purpose Schmitt Input/Output GPIO[2:5], GPIO[8] I/O (PU) General Purpose Input/Output GPIO[6] I/O General Purpose Input/Output (also used for active low reset) GPIO[7] I/O General Purpose Input/Output (also used for active high reset) TDI_GPIO[9] I/O (PU) JTAG test data input OR general purpose input/output. Function of this pin is dependant upon value of JTAGEN bit. When operating in JTAG mode this signal contains serial data that is shifted in on the rising edge of TCK. TMS_GPIO[10] I/O (PU) JTAG test mode select OR general purpose input/output. MISCELLANEOUS Function of this pin is dependant upon value of JTAGEN bit. When operating in JTAG mode this siganl controls the operation of the TAP controller. TRSTN_GPIO[11] I/O (PU) JTAG reset OR general purpose input/output. Function of this pin is dependant upon value of JTAGEN bit. When operating in JTAG mode, a high to low transition on this signal forces the TAP controller into a logic reset state. TCK I JTAG clock. TDO O JTAG data output. This pin generates serial data that is shifted out on the falling edge of TCK.. GPIN0 I (S) General purpose schmitt input (modem ring detect) GPIN1 I (PU,S) General purpose schmitt input (modem offhook) SCANEN I (PD) Scan chain enable. Used to shift data in and out of the scan chain. SCANMODE I (PD) Scan mode enable pin. When tied high it will put the device into scan test mode. REFCLK I 35.328 MHz reference clock used to create the internal 53 MHz system clock POWER AND GROUND 8 VDD 3.3V Power GND Ground VGG1 I/O Clamp Power Supply for PCI Signalling Environment (connect to VIO pin of PCI Bus) VGG2 I/O Clamp Power Supply for Backend (connect to 3.3 volt supply) Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner 11627 ADSL DMT Data Pump Hardware Pins and Signals VDDcore GND 133 135 134 RX[5] RX[4] RX[3] RX[2] 137 136 VDDcore GND 139 138 141 140 RX[9] RX[8] RX[7] RX[6] 143 142 RX[11] RX[10] 145 144 147 146 RX[15] RX[14] RX[13] RX[12] 149 148 GND GND 151 150 153 152 VDD VDDcore VDDcore GND 155 154 TX[1] TX[0] 157 156 159 158 TX[5] TX[4] TX[3] TX[2] 161 160 TX[7] TX[6] 163 162 165 164 VDD GND TX[9] TX[8] 167 166 TX[11] TX[10] 169 168 171 170 TX[15] TX[14] TX[13] TX[12] 173 172 175 174 176 VDD GND The pin assignments for the 11627 are shown in Figure 5 and listed in Table 3. The signals are defined in Table 4. R_INTER_DATA R_FAST_SUPER# 32 33 101 100 R_FAST_FRAME# GND 34 35 99 98 VDD R_NCO_LS0 36 37 97 96 R_NCO_LS1 R_NCO_AS0 38 39 95 94 R_NCO_AS1 R_DAT_AS0 40 41 93 92 R_DAT_AS1 NC 42 43 91 90 NC 44 89 88 103 102 GND 30 31 86 87 DMCK_ALT R_INTER_SUPER# RD# CS# 105 104 84 85 28 29 CLIP# RST# GND NTRCTL 82 83 107 106 IRQ[1]# IRQ[0]# 26 27 80 81 VDDcore VDD NC LTR 109 108 78 79 24 25 MON_CLK PWR_DN AFE_STR# VDDcore 76 77 111 110 VDD MON_OUT 22 23 74 75 TLXCK_EN TXSOC1 GND GND 113 112 72 73 20 21 GND GND GND TXSOC0 70 71 115 114 VDDcore VDDcore 18 19 68 69 GND GND MCLK VDD 117 116 66 67 16 17 VCXO_CTRL MON_DONE T_DAT_LS0 BIT_CLOCK 64 65 119 118 GND NC 14 15 62 63 T_DAT_LS1 T_CLK_LS0 GND GND 121 120 60 61 12 13 VDDcore VDDcore NC T_CLK_LS1 58 59 123 122 NC VDDcore 10 11 56 57 VDD R_CLK_AS0 NC NC 125 124 54 55 8 9 VDD NC NTR GND 52 53 127 126 GND GND 6 7 50 51 R_CLK_AS1 NC R_DAT_LS1 NC 129 128 48 49 4 5 R_DAT_LS0 R_CLK_LS1 T_FAST_BYTE# T_INTER_BYTE# 46 47 131 130 45 132 2 3 RXSOC0 1 RXSOC1 R_CLK_LS0 GND DAC_CLK FILTER_CLK VDD GND RX[1] RX[0] ADC_CLK D[0] D[1] D[2] D[3] D[4] VDD GND D[5] D[6] D[7] D[8] D[9] D[10] D[11] D[12] D[13] D[14] VDD VDDcore VDDcore GND GND GND D[15] VGG A[0] A[1] A[2] A[3] A[4] A[5] A[6] A[7] A[8] VDDcore GND A[9] WR# VDD DSL015_005 Figure 5. 11627 Pinout Diagram Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 9 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Table 3. 11627 Pin Designations by Number Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal 1 GND 37 R_NCO_LS0 73 GND 109 VDDcore 145 RX[10] 2 DAC_CLK 38 R_NCO_LS1 74 GND 110 VDD 146 RX[11] 3 FILTER_CLK 39 R_NCO_AS0 75 GND 111 D[14] 147 RX[12] 4 T_FAST_BYTE# 40 R_NCO_AS1 76 VDD 112 D[13] 148 RX[13] 5 T_INTER_BYTE# 41 R_DAT_AS0 77 MON_OUT 113 D[12] 149 RX[14] 6 R_CLK_AS1 42 R_DAT_AS1 78 MON_CLK 114 D[11] 150 RX[15] 7 NC 43 NC 79 PWR_DN 115 D[10] 151 GND 8 NTR 44 NC 80 NC 116 D[9] 152 GND 9 GND 45 RXSOC0 81 LTR 117 D[8] 153 GND 10 VDD 46 RXSOC1 82 IRQ[1]# 118 D[7] 154 VDDcore 11 R_CLK_AS0 47 R_CLK_LS0 83 IRQ[0]# 119 D[6] 155 VDDcore 12 NC 48 R_DAT_LS0 84 CLIP# 120 D[5] 156 VDD 13 T_CLK_LS1 49 R_CLK_LS1 85 RST# 121 GND 157 TX[0] 14 T_DAT_LS1 50 R_DAT_LS1 86 RD# 122 VDD 158 TX[1] 15 T_CLK_LS0 51 NC 87 CS# 123 D[4] 159 TX[2] 16 T_DAT_LS0 52 GND 88 GND 124 D[3] 160 TX[3] 17 BIT_CLOCK 53 GND 89 VDD 125 D[2] 161 TX[4] 18 GND 54 VDD 90 WR# 126 D[1] 162 TX[5] 19 GND 55 NC 91 A[9] 127 D[0] 163 TX[6] 20 GND 56 NC 92 GND 128 ADC_CLK 164 TX[7] 21 TXSOC0 57 NC 93 VDDcore 129 RX[0] 165 TX[8] 22 TLXCK_EN 58 NC 94 A[8] 130 RX[1] 166 TX[9] 23 TXSOC1 59 VDDcore 95 A[7] 131 GND 167 GND 24 AFE_STR# 60 VDDcore 96 A[6] 132 VDD 168 VDD 25 VDDcore 61 VDDcore 97 A[5] 133 GND 169 TX[10] 26 VDDcore 62 GND 98 A[4] 134 VDDcore 170 TX[11] 27 VDD 63 GND 99 A[3] 135 RX[2] 171 TX[12] 28 GND 64 GND 100 A[2] 136 RX[3] 172 TX[13] 29 NTRCTL 65 NC 101 A[1] 137 RX[4] 173 TX[14] 30 DMCK_ALT 66 VCXO_CTRL 102 A[0] 138 RX[5] 174 TX[15] 31 R_INTER_SUPER# 67 MON_DONE 103 VGG 139 GND 175 GND 32 R_INTER_DATA 68 MCLK 104 D[15] 140 VDDcore 176 VDD 33 R_FAST_SUPER# 69 VDD 105 GND 141 RX[6] 34 R_FAST_FRAME# 70 VDDcore 106 GND 142 RX[7] 35 GND 71 VDDcore 107 GND 143 RX[8] 36 VDD 72 GND 108 VDDcore 144 RX[9] 10 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner Table 4. 11627 Pin Signals by Group Pin Name I/O Description AFE ANALOG-to-DIGITAL INTERFACE RX[15:0] I Receive Data Lines In the parallel mode of operation, data is clocked by the signal ADC_CLK using the full data bus. In the serial mode of operation, a strobe signal (AFE_STR#) from the AFE shall trigger the transfer of data over a programmable width serial bus. ADC_CLK O Receive Clock for Parallel Mode CLIP# O Clip Interrupt This signal is used for monitoring incoming data for saturation. Goes low for one clock (ADC_CLK) cycle whenever clipping is detected. AFE DIGITAL-to-ANALOG INTERFACE TX[15:0] O Transmit Data Lines In the parallel mode of operation, data is clocked by the signal DAC_CLK using the full data bus. In the serial mode of operation, a strobe signal (AFE_STR#) from the AFE shall trigger the transfer of data over a programmable width serial bus. DAC_CLK O Transmit Clock for Parallel Mode FILTER_CLK O AFE Filter Clock This signal is used by the DAC interface block to strobe the external AFE filters. AFE_STR# I AFE Strobe Signal TLXCK_EN I LSX Transmit Data Clock Generation Enable T_CLK_LS0 I/O Transmit Data Clock (LS0) T_CLK_LS1 I/O Transmit Data Clock (LS1) T_DAT_LS0 I Transmit Data (LS0) T_DAT_LS1 I Transmit Data (LS1) R_CLK_LS0 I Receive Data Clock (LS0) R_CLK_LS1 I Receive Data Clock (LS1) R_DAT_LS0 O Receive Data (LS0) R_DAT_LS1 O Receive Data (LS1) R_CLK_AS0 I Receive Data Clock (AS0) R_CLK_AS1 I Receive Data Clock (AS1) R_DAT_AS0 O Receive Data (AS0) DIGITAL INTERFACE (DI) R_DAT_AS1 O Receive Data (AS1) R_NCO_LS0 O Receive LS0 NCO Output R_NCO_LS1 O Receive LS1 NCO Output R_NCO_AS0 O Receive AS0 NCO Output R_NCO_AS1 O Receive AS1 NCO Output BIT_CLOCK O Serial Data Bit Clock Output Used to synchronize the serial input and output data bit streams, enables, and superframe qualifiers. T_FAST_BYTE# O Transmit Fast Data Bit Input Enable T_INTER_BYTE# O Transmit Interleaved Data Bit Input Enable R_FAST_FRAME# O Receive Fast Data Bit Output Frame Qualifier R_FAST_SUPER# O Receive Fast Data Bit Output Superframe Qualifier Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 11 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Pin Name I/O Description R_INTER_DATA O Receive Interleaved Data Bit Output R_INTER_SUPER# O Receive Interleaved Data Bit Output Superframe Qualifier D[15:0] I/O PCI Controller Interface Data Bus A[9:0] I PCI Controller Interface Address Bus Clocked at BIT_CLOCK rate. PCI CONTROLLER INTERFACE 16-bit input/output bus to send/receive data to/from PCI controller. 10-bit input bus to receive address from PCI controller. WR# I Data Write Enable RD# I Data Read Enable CS# I Chip Select IRQ[1:0]# O Programmable Interrupts I Global Chip Reset MISCELLANEOUS RST# When low, puts chip into reset condition. MCLK I High-speed Master Clock Connect to 35.328 MHz VCXO, which is 16 times the maximum Nyquist rate. VXCO_CTRL O Oversampled VCXO analog control voltage MON_OUT O 1-bit serial D/A output used for constellation monitoring MON_CLK O Serial Monitor Clock Operates at 138 kHz. MON_DONE O New Symbol Constellation Qualifier DMCK_ALT I External 2x Clock LTR O 8 kHz Local Timing Reference NTR I/O 8 kHz Network Timing Reference NTRCTL I Network Timing Reference I/O Control TXSOC0 I TC0 Block Transmit Start of Cell. TXSOC1 I TC1 Block Transmit Start of Cell. RXSOC0 O TC0 Block Receive Start of Cell RXSOC1 O TC1 Block Receive Start of Cell PWR_DN I Power Down Control Pin POWER AND GROUND VDD 3.3V Power (I/O) VDDcore 2.5V Power (Core) GND Ground VGG I/O Clamp Power Supply (connect to 5 volt supply for 5 volt tolerance) 12 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner 20431 ADSL Analog Front End Hardware Pins and Signals RBIAS VREFM VC VREFP NC DVSS NC DVSS 32 31 30 29 28 27 26 25 The pin assignments for the 20431 are shown in Figure 6 and defined in Table 5. INP_HYBR_RX 1 24 RX0 INM_HYBR_RX 2 23 RX1 16 CTRL_OUT CTRL_IN WAKEUP 17 15 18 8 14 7 DVSS OUTP_TX OUTM_TX CTRL_STRB STROBE 13 19 POR 6 12 NC AVSS 11 20 NC 5 CLKIN DVDD AVDD 10 TX0 21 AVSS 22 4 9 3 AVDD INP_RX INM_RX DSL015_006 Figure 6. 20431 Pinout Diagram Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 13 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Table 5. 20431 Pin Signals by Group Pin Name I/O Description Pin Number(s) ADSL Digital Serial Data and Control Interface Signals CLKIN I Clock input (35.328MHz) 11 POR I Power On Reset 13 CTRL_STRB I Strobe for the control interface 15 CTRL_IN I Digital input of the control interface 16 CTRL_OUT O Digital output of the control interface 17 WAKEUP O Digital output for tone detection mode 18 STROBE O Strobe for the data interface 19 TX0 I Digital transmit input 22 RX1 O Digital receive output 23 RX0 O Digital receive output 24 ADSL HYBRID CIRCUIT AND LINE DRIVER INTERFACE INP_HYBR_RX I Positive input of hybrid receiver circuit 1 INM_HYBR_RX I Negative input of hybrid receiver circuit 2 INP_RX I Positive input of receive path 3 INM_RX I Negative input of receive path 4 OUTP_TX O Positive output of transmit path 7 OUTM_TX O Negative output of transmit path 8 VREFP --- Analog reference voltage (2.5V) 29 VC --- Analog reference voltage (1.5V) 30 VREFM --- Analog reference voltage (0.5V) 31 RBIAS --- Analog current reference 32 AVDD --- Analog supply 5, 9 AVSS --- Analog ground 6, 10 DVSS --- Digital ground 14, 25, 27 DVDD --- Digital supply 21 Overhead Signals 14 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner 20441 ADSL Line Driver Hardware Pins and Signals 32 31 30 29 28 27 26 25 NC NC NC NC NC NC NC NC The pin assignments for the 20441 in both 16-pin TSSOP and 32-pin TQFP packages are shown in Figure 7 and defined in Table 6. 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 NC INP_DRV NC NC NC AVDD OUTP_DRV AVSS NC INM_DRV NC RBIAS PWRDWN# AVDD OUTM_DRV AVSS 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 NC INP_DRV NC NC NC AVDD OUTP_DRV AVSS NC NC NC NC NC NC NC NC 9 10 11 12 13 14 15 16 NC INM_DRV NC RBIAS PWRDWN# AVDD OUTM_DRV AVSS 16-pin TSSOP 32-pin TQFP DSL015_007 Figure 7. 20441 Pinout Diagrams Table 6. 20441 Pin Signals by Group Pin Name I/O Description Comment Pin Number(s) 16 SSOP 32 TQFP INP_DRV I Positive transmit output of the AFE Analog input 15 23 INM_DRV I Negative transmit output of the AFE Analog input 2 2 OUTP_DRV O Positive output of the line driver Analog output Imax=244mA (16 SSOP) Imax=280mA (32 SSOP) 10 18 OUTM_DRV O Negative output of the line driver Analog output Imax=244mA (16 SSOP) Imax=280mA (32 TQFP) 7 7 PWRDWN# I Power down control (0 = power down) Digital input (3V level) 5 5 RBIAS I Current setting external resistor Tied to 125k resistor (+1%) 4 4 AVDD Analog supply (+5V) Imax=273.2mA (16 SSOP) Imax=309.2mA (32 TQFP) 6, 11 6, 19 AVSS Analog ground Imax=273.2mA (16 SSOP) Imax=309.2mA (32 TQFP) 8, 9 8, 17 POWER Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 15 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Electrical and Environmental Specifications AccessRunner P46 PCI Bus Interface Device Table 7. DC Characteristics Parameter Symbol Minimum Maximum Units 3.6 VDC Conditions Power Power Supply VDD 3.0 PCI Signal/Power Levels - 3V signalling environment I/O Clamp Power Supply Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage VIO VIL VIH VOL VOH VDD -0.5 0.5 * Vdd I/O Clamp Power Supply Input Low Voltage Input High Voltage Output Low Voltage VIO VIL VIH VOL Output Low Voltage VOL Output High Voltage VOH Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage VIL VIH VOL VOH -0.5 2.0 Pull-Up Resistance Pull-Down Resistance Rpu Rpd 50 50 3.6 0.3 * Vdd Vdd + 0.5 0.1 * Vdd 0.9 * Vdd VDC VDC VDC VDC VDC Iout = -500 mA Iout = 1500mA PCI Signal/Power Levels - 5V signaling environment VDD -0.5 2.0 5.25 0.8 Vdd + 0.5 0.55 VDC VDC VDC VDC 0.55 VDC 2.4 VDC Iout = 3mA, signals without pullups Iout = 6mA, signals with pullups Iout = -2mA TTL Signal Levels 0.8 Vdd + 0.5 0.4 VDC VDC VDC VDC 200 200 Kohm Kohm 2.4 Misc 16 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner AccessRunner 11627 ADSL DMT Data Pump Table 8. Recommended Operating Conditions Parameter Symbol Min Typ Max Units Power Supply (I/O) VDD 3.135 3.3 3.465 Volts Power Supply (Core) VDDcore 2.375 2.5 2.625 Volts Ambient Operating Temperature TA -40 +85 C 90 % Humidity Table 9. Absolute Maximum Ratings Parameter Symbol Power Supply VDD Voltage on any Signal Pin Min Typ Max Units 3.6 Volts GND-0.3 VDD+0.3 Volts Ambient Operating Temperature TA -55 +125 C Storage Temperature TS -65 +150 C Junction Temperature TJ +150 C Soldering Temperature TSOL +260 C Vapor Phase Soldering TVSOL +220 C Air Flow 0 l.f.p.m Table 10. DC Characteristics Parameter Symbol Min Input High Voltage VIH Input Low Voltage Input Leakage Current Input Capacitance CIN Typ Max Units 0.9*VDD VDD Volts VIL GND 0.1*VDD Volts IIL/IIH -10 10 A Digital Inputs 2.9 pF Digital Outputs Output High Voltage VOH 0.9*VDD VDD Volts Output Low Voltage VOL GND 0.1*VDD Volts Tri-State Output Leakage ILK 10 10 A Output Capacitance COUT 3.1 pF Digital Bi-directionals Tri-State Output Leakage ILK Input/Output Capacitance CINOUT Doc. No. 100394B October 19, 1999 Conexant Proprietary Information -10 10 3.9 A pF 17 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications AccessRunner 20431 AFE Table 11. Recommended Operating Conditions Parameter Min Typ Max Units Power supply 3.135 3.3 3.465 V Operating junction temperature -40 +100 o +85 o Operating ambient temperature -40 C C Table 12. Absolute Maximum Ratings Parameter Min Max Units Power supply -0.35 3.6 V Analog input voltage -0.35 Vdd+0.35 V Digital input voltage -0.35 Vdd+0.35 V Input current per Pin -10 10 mA Output current per Pin -50 50 mA 1 sec +125 o +150 o Short circuit duration, to GND or Vdd Ambient temperature (power applied) Storage temperature -55 -65 C C Table 13. Power Consumption Parameter Min Typ Max Units Analog 40.5 mA Digital 25 mA Table 14. Digital Characteristics 18 Parameter Min Max Units High level input voltage 0.65*VDD VDD+0.35 V Low level input voltage -0.35 0.25*VDD V High level output voltage 0.85*VDD VDD V Low level output voltage 0 0.1*VDD V Input leakage current -10 10 A Output leakage current -10 10 A Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner AccessRunner 20441 Line Driver Table 15. Power Consumption Parameter Min Line driver Typ Max Units 18 24 mA Table 16. Absolute Maximum Ratings Parameter Min Max Units Power supply -0.35 7 V Analog input voltage -0.35 Vdd+0.35 V Digital input voltage -0.35 Vdd+0.35 V Input current per Pin -10 10 mA Output current per Pin -50 50 mA 1 Sec +125 o +150 o Short circuit duration, to GND or Vdd Ambient temperature (power applied) -55 Storage temperature -65 C C Table 17. Recommended Operating Conditions Parameter Min Typ Max Units Power supply 4.75 5 5.25 V Operating junction temperature -40 +110 o +70 o Operating ambient temperature Doc. No. 100394B October 19, 1999 0 Conexant Proprietary Information C C 19 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications Package Dimensions 26.0 .20 0.500 0.500 26.0 23.87 .20 0.500 .10 24.00 .10 0.220 REF. 23.87 .10 24.00 .10 Detail "A" 12 R 0.15 TYP R 0.20 TYP 1.40 .05 0 -5 GAUGE PLANE SEATING PLANE 12 0.25 .05 MIN./.15 MAX. 1.00 REF. 0.30 REF. 0.60 + .15/ .10 DETAIL A DSL015_008 Figure 8. 176-pin TQFP Package Dimensions 20 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner D D1 D2 D D1 D2 D1 e b S Y M B O L Detail "A" D1 A A2 c A A1 A2 D D1 D2 L L1 e b c Coplanarity Millimeters MAX. MIN. 1.6 MAX. 0.15 0.05 1.4 REF. 9.25 8.75 7.0 REF. 5.6 REF. 0.75 0.5 1.0 REF. 0.80 BSC 0.40 0.30 0.19 0.13 0.10 MAX. Inches MAX. MIN. 0.0630 MAX. 0.0020 0.0059 0.0551 REF. 0.3445 0.3642 0.2756 REF. 0.2205 REF. 0.0197 0.0295 0.0394 REF. 0.0315 BSC 0.0118 0.0157 0.0051 0.0075 0.004 MAX. Ref: 32-Pin TQFP (GP00-D262) A1 * Metric values (millimeters) should be used for PCB layout. English values (inches) are converted from metric values and may include round-off errors. L DETAIL A L1 DSL015_009 Figure 9. 32-pin TQFP Package Dimensions Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 21 AccessRunner Controller-less ADSL Modem Device Set for PCI Applications NOTES: 0.193 0.002 [WITHOUT FLASH] 1. THERMAL HEATSINK/RF GROUND MATERIAL: OFHC COPPER -A- 2. LEAD COPLANARITY IS 0.004 MAX. 3. L/F MATERIAL: COPPER 151, 0.0075 THICK 4. LEAD AND HEATSINK FINISH: 85Pb/15 5Sn -B5. FLASH IS 0.010 MAX. 0.154 0.002 [WITHOUT FLASH] TOP VIEW .0001 1 .0025 0.023 PIN 1 0.010 TYP. 0.193 VIEW B SCALE 2:1 0.002 0.058 0.002 [MOLD] 7 (TYP) 0.015 X 45 R0.005 (TYP. 4X) VIEW B 0 -7 TYP. -C0.004 VIEW A SEATING PLANE 0.194 0.000 0.004 0.002 O.008 TYP. .174 SIDE VIEW END VIEW .110 0.236 FLASH (TYP) 0.024 0.002 MEASURED 0.0098 FROM SEATING PLANE 0.004 0.008 MAX. .005 A B 1 .066 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES VIEW A SCALE: 100:1 +0.004 0.010 -0.002 TOERANCES ON: BOTTOM VIEW 0.025 TYP. DECIMALS .XX .03 .XXX .002 ANGLES 0.30 XXX M C 16 LEAD SSOP PACKAGE OUTLINE DSL015_010 Figure 10. 16-pin SSOP Package Dimensions 22 Conexant Proprietary Information Doc. No. 100394B October 19, 1999 Controller-less ADSL Modem Device Set for PCI Applications AccessRunner INSIDE BACK COVER NOTES Doc. No. 100394B October 19, 1999 Conexant Proprietary Information 23 Further Information: literature@conexant.com 1-800-854-8099 (North America) 33-14-906-3980 (International) Web Site www.conexant.com Hong Kong Phone: (852) 2 827 0181 Fax: (852) 2 827 6488 India Phone: (91 11) 692 4780 Fax: (91 11) 692 4712 World Headquarters Conexant Systems, Inc. 4311 Jamboree Road, P.O. Box C Newport Beach, CA 92658-8902 Phone: (949) 483-4600 Fax: (949) 483-6375 Korea - Seoul Office Phone: (82 2) 565 2880 Fax: (82 2) 565 1440 U.S. Florida/South America Phone: (727) 799-8406 Fax: (727) 799-8306 Europe Headquarters Conexant Systems France Les Taissounieres B1 1681 Route des Dolines BP 283 06905 Sophia Antipolis Cedex France Phone: (33 4) 93 00 33 35 Fax: (33 4) 93 00 33 03 U.S. Los Angeles Phone: (805) 376-0559 Fax: (805) 376-8180 U.S. Mid-Atlantic Phone: (215) 244-6784 Fax: (215) 244-9292 U.S. North Central Phone: (630) 773-3454 Fax: (630) 773-3907 U.S. Northeast Phone: (978) 692-7660 Fax: (978) 692-8185 U.S. Northwest/Pacific West Phone: (408) 249-9696 Fax: (408) 249-7113 U.S. South Central Phone: (972) 733-0723 Fax: (972) 407-0639 U.S. Southeast Phone: (919) 858-9110 Fax: (919) 858-8669 U.S. Southwest Phone: (949) 483-9119 Fax: (949) 483-9090 APAC Headquarters Conexant Systems Singapore, Pte. Ltd. 1 Kim Seng Promenade Great World City #09-01 East Tower Singapore 237994 Phone: (65) 737 7355 Fax: (65) 737 9077 Australia Phone: (61 2) 9869 4088 Fax: (61 2) 9869 4077 China Phone: (86 2) 6361 2515 Fax: (86 2) 6361 2516 Korea - Taegu Office Phone: (82 53) 745-2880 Fax: (82 53) 745-1440 Europe Central Phone: (49 89) 829 1320 Fax: (49 89) 834 2734 Europe Mediterranean Phone: (39 02) 9317 9911 Fax (39 02) 9317 9913 Europe North Phone: (44 1344) 486 444 Fax: (44 1344) 486 555 Europe South Phone: (33 1) 41 44 36 50 Fax: (33 1) 41 44 36 90 Middle East Headquarters Conexant Systems Commercial (Israel) Ltd. P.O. Box 12660 Herzlia 46733 Israel Phone: (972 9) 952 4064 Fax: (972 9) 951 3924 Japan Headquarters Conexant Systems Japan Co., Ltd. Shimomoto Building 1-46-3 Hatsudai, Shibuya-ku Tokyo, 151-0061 Japan Phone: (81 3) 5371 1567 Fax: (81 3) 5371 1501 Taiwan Headquarters Conexant Systems, Taiwan Co., Ltd. Room 2808 International Trade Building 333 Keelung Road, Section 1 Taipei 110 Taiwan, ROC Phone: (886 2) 2720 0282 Fax: (886 2) 2757 6760