1
Motorola Small–Signal Transistors, FETs and Diodes Device Data
NPN Silicon
MAXIMUM RATINGS
Rating Symbol Value Unit
Collector–Emitter Voltage VCEO 140 Vdc
Collector–Base Voltage VCBO 160 Vdc
Emitter–Base Voltage VEBO 6.0 Vdc
Collector Current — Continuous IC600 mAdc
THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Total Device Dissipation FR–5 Board(1)
TA = 25°C
Derate above 25°C
PD225
1.8
mW
mW/°C
Thermal Resistance, Junction to Ambient R
q
JA 556 °C/W
Total Device Dissipation
Alumina Substrate,(2) TA = 25°C
Derate above 25°C
PD300
2.4
mW
mW/°C
Thermal Resistance, Junction to Ambient R
q
JA 417 °C/W
Junction and Storage Temperature TJ, Tstg –55 to +150 °C
DEVICE MARKING
MMBT5550LT1 = M1F; MMBT5551LT1 = G1
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic Symbol Min Max Unit
OFF CHARACTERISTICS
Collector–Emitter Breakdown Voltage(3)
(IC = 1.0 mAdc, IB = 0) MMBT5550
MMBT5551
V(BR)CEO 140
160 —
—
Vdc
Collector–Base Breakdown Voltage
(IC = 100
m
Adc, IE = 0) MMBT5550
MMBT5551
V(BR)CBO 160
180 —
—
Vdc
Emitter–Base Breakdown Voltage
(IE = 10
m
Adc, IC = 0) V(BR)EBO 6.0 — Vdc
Collector Cutoff Current
(VCB = 100 Vdc, IE = 0) MMBT5550
(VCB = 120 Vdc, IE = 0) MMBT5551
(VCB = 100 Vdc, IE = 0, TA = 100°C) MMBT5550
(VCB = 120 Vdc, IE = 0, TA = 100°C) MMBT5551
ICBO —
—
—
—
100
50
100
50
nAdc
µAdc
Emitter Cutoff Current
(VEB = 4.0 Vdc, IC = 0) IEBO — 50 nAdc
1. FR–5 = 1.0
0.75
0.062 in.
2. Alumina = 0.4
0.3
0.024 in. 99.5% alumina.
3. Pulse Test: Pulse Width = 300
m
s, Duty Cycle = 2.0%.
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
Order this document
by MMBT5550LT1/D
SEMICONDUCTOR TECHNICAL DATA
12
3
CASE 318–08, STYLE 6
SOT–23 (TO–236AB)
*Motorola Preferred Device
Motorola, Inc. 1996
COLLECTOR
3
1
BASE
2
EMITTER
2 Motorola Small–Signal Transistors, FETs and Diodes Device Data
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) (Continued)
Characteristic Symbol Min Max Unit
ON CHARACTERISTICS
DC Current Gain
(IC = 1.0 mAdc, VCE = 5.0 Vdc) MMBT5550
MMBT5551
(IC = 10 mAdc, VCE = 5.0 Vdc) MMBT5550
MMBT5551
(IC = 50 mAdc, VCE = 5.0 Vdc) MMBT5550
MMBT5551
hFE 60
80
60
80
20
30
—
—
250
250
—
—
—
Collector–Emitter Saturation Voltage
(IC = 10 mAdc, IB = 1.0 mAdc) Both Types
(IC = 50 mAdc, IB = 5.0 mAdc) MMBT5550
MMBT5551
VCE(sat) —
—
—
0.15
0.25
0.20
Vdc
Base–Emitter Saturation Voltage
(IC = 10 mAdc, IB = 1.0 mAdc) Both Types
(IC = 50 mAdc, IB = 5.0 mAdc) MMBT5550
MMBT5551
VBE(sat) —
—
—
1.0
1.2
1.0
Vdc
3
Motorola Small–Signal Transistors, FETs and Diodes Device Data
Figure 1. DC Current Gain
IC, COLLECTOR CURRENT (mA)
500
h , DC CURRENT GAIN
FE
TJ = 125
°
C
–55
°
C
25
°
C
5.0
10
0.1 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 30 50 70 100
200
30
20
300
100
50
7.0
VCE = 1.0 V
VCE = 5.0 V
Figure 2. Collector Saturation Region
IB, BASE CURRENT (mA)
1.0
IC = 1.0 mA
0
0.3
0.005 0.01 0.2 0.5 1.0 2.0 20 50
0.8
0.5
0.4
0.9
0.7
0.6
0.2
0.02 0.05 0.1 10
VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS)
0.1
10 mA 30 mA 100 mA
5.0
Figure 3. Collector Cut–Off Region
VBE, BASE–EMITTER VOLTAGE (VOLTS)
101
10–50.4 0.3 0.1
100
10–1
10–2
10–3
10–4
0.2 0 0.1 0.2 0.40.3 0.60.5
VCE = 30 V
TJ = 125
°
C
75
°
C
25
°
C
IC = ICES
, COLLECTOR CURRENT ( A)
µ
IC
REVERSE FORWARD
IC, COLLECTOR CURRENT (mA)
1.0
V, VOLTAGE (VOLTS)
1.0 2.0 5.0 10 20 50 100
TJ = 25
°
C
VBE(sat) @ IC/IB = 10
VCE(sat) @ IC/IB = 10
0.1 0.2 0.5
Figure 4. “On” Voltages
0.8
0.6
0.4
0.2
03.0 300.3
4 Motorola Small–Signal Transistors, FETs and Diodes Device Data
C, CAPACITANCE (pF)
VR, REVERSE VOLTAGE (VOLTS)
100
1.00.2 0.5 1.0 2.0 5.0 10 20
Cibo
70
50
30
20
10
7.0
5.0
3.0
2.0
0.3 0.7 3.0 7.0
Cobo
10.2 V
Vin
10
µ
s
INPUT PULSE
VBB
–8.8 V
100
RB
5.1 k
0.25
µ
F
Vin 100 1N914
Vout
RC
VCC
30 V
3.0 k
tr, tf
≤
10 ns
DUTY CYCLE = 1.0%
Values Shown are for IC @ 10 mA
TJ = 25
°
C
IC, COLLECTOR CURRENT (mA)
1000
0.3 1.0 10 20 30 50
0.50.2
t, TIME (ns)
10
20
30
50
100
200
300
500
2.0 100 200
IC/IB = 10
TJ = 25
°
C
tr @ VCC = 120 V
3.0 5.0
tr @ VCC = 30 V
td @ VEB(off) = 1.0 V
VCC = 120 V
IC, COLLECTOR CURRENT (mA)
5000
t, TIME (ns)
50
100
200
300
500
3000
2000
1000
0.3 1.0 10 20 30 50
0.50.2 2.0 100 200
3.0 5.0
IC/IB = 10
TJ = 25
°
C
tf @ VCC = 120 V
tf @ VCC = 30 V
ts @ VCC = 120 V
IC, COLLECTOR CURRENT (mA)
2.5
q
VC for VCE(sat)
q
VB for VBE(sat)
Figure 5. Temperature Coefficients
TJ = –55
°
C to +135
°
C
V, TEMPERATURE COEFFICIENT (mV/ C)
°θ
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
–2.5 1.0 2.0 5.0 10 20 50 1000.1 0.2 0.5 3.0 300.3
Figure 6. Switching Time Test Circuit
Figure 7. Capacitances Figure 8. Turn–On Time
Figure 9. Turn–Off Time
5
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOT–23
mm
inches
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, RθJA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the SOT–23 package,
PD can be calculated as follows:
PD = TJ(max) – TA
RθJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature T A of 25°C, one can
calculate the power dissipation of the device which in this
case is 225 milliwatts.
PD = 150°C – 25°C
556°C/W = 225 milliwatts
The 556°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
•Always preheat the device.
•The delta temperature between the preheat and
soldering should be 100°C or less.*
•When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10°C.
•The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
•When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
•After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
•Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
6 Motorola Small–Signal Transistors, FETs and Diodes Device Data
PACKAGE DIMENSIONS
DJ
K
L
A
C
BS
H
GV
3
12
CASE 318–08
SOT–23 (TO–236AB)
STYLE 6:
PIN 1. BASE
2. EMITTER
3. COLLECTOR
DIM
AMIN MAX MIN MAX
MILLIMETERS
0.1102 0.1197 2.80 3.04
INCHES
B0.0472 0.0551 1.20 1.40
C0.0350 0.0440 0.89 1.11
D0.0150 0.0200 0.37 0.50
G0.0701 0.0807 1.78 2.04
H0.0005 0.0040 0.013 0.100
J0.0034 0.0070 0.085 0.177
K0.0180 0.0236 0.45 0.60
L0.0350 0.0401 0.89 1.02
S0.0830 0.0984 2.10 2.50
V0.0177 0.0236 0.45 0.60
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD
FINISH THICKNESS. MINIMUM LEAD THICKNESS
IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
ISSUE AE
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “T ypicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Af firmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MMBT5550LT1/D
◊
