CRCW...BC e3
www.vishay.com Vishay BCcomponents
Revision: 30-Jan-13 1Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Lead (Pb)-free Thick Film, Rectangular Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Excellent stability (R/R 1 % for 1000 h at
70 °C)
• Lead (Pb)-free solder contacts on Ni barrier layer
• Metal glaze on high quality ceramic
• Protective overglaze
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P70 °C
W
LIMITING
ELEMENT
VOLTAGE
MAX. V
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
RESISTANCE
RANGE
E-SERIES
CRCW0201...BC 0201 RR 0603M 0.05 30
± 200 ± 0.5 10R to 10M E96
- 200/+ 400 1R0 to 9R76
± 100
± 1
47R to 10M
E24; E96± 200 10R to 10M
- 200/+ 400 1R0 to 9R76
± 200 ± 5 10R to 10M E24
- 200/+ 400 1R0 to 9R76
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. at 70 °C = 1.0 A
CRCW0402...BC 0402 RR 1005M 0.063 50
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 1.5 A
CRCW0603...BC 0603 RR 1608M 0.10 75
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.0 A
CRCW0805...BC 0805 RR 2012M 0.125 150
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.5 A
CRCW1206...BC 1206 RR 3216M 0.25 200
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 3.5 A
CRCW1210...BC 1210 RR 3225M 0.50 200
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 4.0 A
CRCW2010...BC 2010 RR 5025M 0.75 400
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 5.0 A
CRCW2512...BC 2512 RR 6332M 1.0 500
± 100 ± 1 1R0 to 10M E24; E96
± 200 1R0 to 9R76
± 200 ± 5 1R0 to 10M E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 7.0 A
CRCW...BC e3
www.vishay.com Vishay BCcomponents
Revision: 30-Jan-13 2Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
TECHNICAL SPECIFICATIONS
PARAMETER UNIT
CRCW0201...BC CRCW0402...BC CRCW0603...BC CRCW0805...BC CRCW1206...BC CRCW1210...BC CRCW2010...BC CRCW2512...BC
Rated
Dissipation
at 70 °C (1)
W 0.050 0.063 0.10 0.125 0.25 0.50 0.75 1.0
Limiting
Element
Voltage
Umax. AC/DC
V 30 50 75 150 200 200 400 500
Insulation
Voltage
Uins (1 min)
V 50 75 100 200 300 300 300 300
Insulation
Resistance > 109
Operating
Temperature
Range
°C - 55 to + 155
Failure Rate °C 0.3 x 10-9
Weight/
1000 Pieces g 0.17 0.65 2 5.5 10 16 25.5 40.5
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW0603562RFKTCBC
MODEL VALUE TOLERANCE TCR PACKAGING Special
CRCW0201
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW2010
CRCW2512
R = Decimal
K = Thousand
M = Million
0000 = Jumper
D = ± 0.5 %
F = ± 1.0 %
J = ± 5.0 %
Z = Jumper
K = ± 100 ppm/K
N = ± 200 ppm/K
X = - 200 ppm/K/
+ 400 ppm/K
0 = Jumper
TA, TB
TC, TD
TE, TF
TH, TI
Up to 2 digits
BC = Commodity
PRODUCT DESCRIPTION: CRCW0603-BC 100 562R 1 % RT6 e3
CRCW0603-BC 100 562R 1 % RT6 e3
MODEL TCR RESISTANCE
VALUE
TOLERANCE
VALUE PACKAGING LEAD (Pb)-FREE
CRCW0201-BC
CRCW0402-BC
CRCW0603-BC
CRCW0805-BC
CRCW1206-BC
CRCW1210-BC
CRCW2010-BC
CRCW2512-BC
± 100 ppm/K
± 200 ppm/K
- 200 ppm/K/
+ 400 ppm/K
10R = 10
562R = 562
10K = 10.0 k
1M = 1 M
0R0 = Jumper
± 0.5 %
± 1 %
± 5 %
RT1, RT2
RT5, RT6
RT7, RF4
R02, R82
e3 = Pure tin
termination finish
C R C W 0 6 0 3 5 6 2 R F K T C B C
CRCW...BC e3
www.vishay.com Vishay BCcomponents
Revision: 30-Jan-13 3Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in millimeters
Note
(1) The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of
power dissipation may raise the temperature of the solder joint, hence special solder alloys or boardmaterials maybe required to maintain
the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on boardmaterials.
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or
in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many
other parameters. Still the given solder pad dimensions will be found adequate for most general applications.
(2) No marking for 0201 and 0402 sizes.
PACKAGING
MODEL
REEL
TAPE WIDTH DIAMETER PITCH PIECES/
REEL
PACKAGING CODE
PART NUMBER PRODUCT DESC.
PAPER BLISTER PAPER BLISTER
CRCW0201…BC 8 mm
180 mm/7"
2 mm
10 000 TD - RT7 -
254 mm/10" 20 000 TI - RT2 -
330 mm/13" 50 000 TE - RF4 -
CRCW0402…BC 8 mm
180 mm/7"
2 mm
10 000 TD - RT7 -
254 mm/10" 20 000 TI - RT2 -
330 mm/13" 50 000 TE - RF4 -
CRCW0603…BC 8 mm
180 mm/7"
4 mm
5000 TA - RT1 -
254 mm/10" 10 000 TB - RT5 -
330 mm/13" 20 000 TC - RT6 -
CRCW0805…BC 8 mm
180 mm/7"
4 mm
5000 TA - RT1 -
254 mm/10" 10 000 TB - RT5 -
330 mm/13" 20 000 TC - RT6 -
CRCW1206…BC 8 mm
180 mm/7"
4 mm
5000 TA - RT1 -
254 mm/10" 10 000 TB - RT5 -
330 mm/13" 20 000 TC - RT6 -
CRCW1210…BC 8 mm
180 mm/7"
4 mm
5000 TA - RT1 -
254 mm/10" 10 000 TB - RT5 -
330 mm/13" 20 000 TC - RT6 -
CRCW2010…BC 12 mm 180 mm/7" 4 mm 4000 - TF - R02
CRCW2512…BC 12 mm 180 mm/7" 4 mm 4000 - TH - R82
SIZE DIMENSIONS SOLDER PAD DIMENSIONS (1)
REFLOW SOLDERING WAVE SOLDERING
INCH METRIC L W H T1 T2 a b l a b l
0201 0603 0.6 ± 0.05 0.3 ± 0.05 0.23 ± 0.05 0.15 ± 0.05 0.2 + 0.05
- 0.10 0.30.430.2 - - -
0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5 - - -
0603 1608 1.55 + 0.10
- 0.05 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0
0805 2012 2.0 + 0.20
- 0.10 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.20
- 0.10 0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3
1206 3216 3.2 + 0.10
- 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3
1210 3225 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2
2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9
2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2
CRCW...BC e3
www.vishay.com Vishay BCcomponents
Revision: 30-Jan-13 4Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DERATING
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE CHANGE (R)
STABILITY
CLASS 1
OR BETTER
STABILITY
CLASS 2
OR BETTER
SIZE 0201
Stability for product types:
CRCW....BC e3 1to 10 M1to 10 M1to 10 M
4.5 - Resistance - ± 1 % ± 5 %
± 0.5 %, ± 1 %, ± 5 %
4.8.4.2 - Temperature
coefficient
(20/- 55/20) °C and
(20/125/20) °C
± 100 ppm/K,
± 200 ppm/K ± 200 ppm/K
± 100 ppm/K,
± 200 ppm/K,
- 200 ppm/K/
+ 400 ppm/K
4.13 - Short time
overload
U= 2.5 x 2 x Umax.;
duration: Acc. to the style ± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (1 % R + 0.05 )
4.17.5 58 (Td) Solderability
Pre-aging
4 h at 155 °C,
dryheat
Solder bath
method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Good tinning ( 95 % covered)
no visible damage
Solder bath
method;
Sn96.5Ag3Cu0.5
non activated flux;
(245 ± 5) °C
(3 ± 0.3) s
Good tinning ( 95 % covered)
no visible damage
4.18.2 58 (Td) Resistance to
soldering heat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (1 % R + 0.05 )
4.19 14 (Na) Rapid change
of temperature
30 min. at - 55 °C;
30 min. at 125 °C;
5 cycles ± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (0.5 % R + 0.05 )
1000 cycles ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) ± (1 % R + 0.05 )
4.24 78 (Cab) Damp heat,
steady state
(40 ± 2) °C;
56 days;
(93 ± 3) % RH
± (1 % R + 0.05 )± (2 % R + 0.1 )± (2 % R + 0.1 )
- 55 - 25 0 25 50 75 100 125 155 175
120
100
80
60
40
20
0
70 Ambient Temperature in °C
Rated Power in %
P70 x R
CRCW...BC e3
www.vishay.com Vishay BCcomponents
Revision: 30-Jan-13 5Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4.23 - Climatic
sequence: -
± (1 % R + 0.05 )± (2 % R + 0.1 )± (2 % R + 0.1 )
4.23.2 2 (Ba) Dry heat 125 °C; 16 h
4.23.3 30 (Db) Damp heat,
cyclic
55 °C; 90 % RH;
24 h; 1 cycle
4.23.4 1 (Aa) Cold - 55 °C; 2 h
4.23.5 13 (M) Low air
pressure 1kPa; (25± 10) °C; 1h
4.23.6 30 (Db) Damp heat,
cyclic
55 °C; 90 % RH;
24 h; 5 cycles
4.23.7 - DC load U= Umax.
4.25.1 - Endurance
at 70 °C
U= Umax.;
1.5 h on; 0.5 h off;
70 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )± (2 % R + 0.1 )
70 °C; 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )± (4 % R + 0.1 )
4.25.3 - Endurance
at 125 °C 125 °C, 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )± (2 % R + 0.1 )
APPLICABLE SPECIFICATIONS
• EN60115-1Generic specification
• EN140400Sectional specification
• EN140401-802Detail specification
• IEC 60068-2-XVariety of environmental test procedures
• IEC 60286-3Packaging of SMD components
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE CHANGE (R)
STABILITY
CLASS 1
OR BETTER
STABILITY
CLASS 2
OR BETTER
SIZE 0201
Stability for product types:
CRCW....BC e3 1to 10 M1to 10 M1to 10 M
P70 x R
P70 x R
