W25Q256JV 3V 256M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI For Industrial & Industrial Plus Grade Publication Release Date: October 23, 2018 Revision I W25Q256JV Table of Contents 1. GENERAL DESCRIPTIONS ............................................................................................................. 5 2. FEATURES ....................................................................................................................................... 5 3. PACKAGE TYPES AND PIN CONFIGURATIONS........................................................................... 6 4. 3.1 Pad Configuration WSON 8x6-mm, WFLGA 6x5-mm ......................................................... 6 3.2 Pad Description WSON 8x6-mm, WFLGA 6x5-mm ............................................................ 6 3.3 Pin Configuration SOIC 300-mil ........................................................................................... 7 3.4 Pin Description SOIC 300-mil ............................................................................................... 7 3.5 Ball Configuration TFBGA 8x6-mm (5x5 or 6x4 Ball Array) ................................................. 8 3.6 Ball Description TFBGA 8x6-mm ......................................................................................... 8 PIN DESCRIPTIONS ........................................................................................................................ 9 4.1 Chip Select (/CS) .................................................................................................................. 9 4.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) ..................................... 9 4.3 Write Protect (/WP) .............................................................................................................. 9 4.4 HOLD (/HOLD) ..................................................................................................................... 9 4.5 Serial Clock (CLK) ................................................................................................................ 9 4.6 Reset (/RESET)(1) ................................................................................................................. 9 5. BLOCK DIAGRAM .......................................................................................................................... 10 6. FUNCTIONAL DESCRIPTIONS ..................................................................................................... 11 6.1 6.2 7. SPI Operations ................................................................................................................... 11 6.1.1 Standard SPI Instructions ..................................................................................................... 11 6.1.2 Dual SPI Instructions ............................................................................................................ 11 6.1.3 Quad SPI Instructions ........................................................................................................... 11 6.1.4 3-Byte / 4-Byte Address Modes ............................................................................................ 12 6.1.5 Software Reset & Hardware /RESET pin .............................................................................. 12 Write Protection .................................................................................................................. 13 STATUS AND CONFIGURATION REGISTERS ............................................................................ 14 7.1 Status Registers ................................................................................................................. 14 7.1.1 Erase/Write In Progress (BUSY) - Status Only ................................................................ 14 7.1.2 Write Enable Latch (WEL) - Status Only .......................................................................... 14 7.1.3 Block Protect Bits (BP3, BP2, BP1, BP0) - Volatile/Non-Volatile Writable ....................... 15 7.1.4 Top/Bottom Block Protect (TB) - Volatile/Non-Volatile Writable ....................................... 15 7.1.5 Complement Protect (CMP) - Volatile/Non-Volatile Writable ............................................ 15 7.1.1 Status Register Protect (SRP, SRL) - Volatile/Non-Volatile Writable ............................... 16 7.1.2 Erase/Program Suspend Status (SUS) - Status Only....................................................... 17 7.1.3 Security Register Lock Bits (LB3, LB2, LB1) - Volatile/Non-Volatile OTP Writable .......... 17 7.1.4 Quad Enable (QE) - Volatile/Non-Volatile Writable .......................................................... 17 -1- W25Q256JV 7.2 8. 7.1.5 Current Address Mode (ADS) - Status Only ..................................................................... 18 7.1.6 Power-Up Address Mode (ADP) - Non-Volatile Writable .................................................. 18 7.1.7 Write Protect Selection (WPS) - Volatile/Non-Volatile Writable ....................................... 18 7.1.8 Output Driver Strength (DRV1, DRV0) - Volatile/Non-Volatile Writable ........................... 19 7.1.9 Reserved Bits - Non Functional ........................................................................................ 19 7.1.10 W25Q256JV Status Register Memory Protection (WPS = 0, CMP = 0) ............................. 20 7.1.11 W25Q256JV Status Register Memory Protection (WPS = 0, CMP = 1) ............................. 21 7.1.12 W25Q256JV Individual Block Memory Protection (WPS=1) .............................................. 22 Extended Address Register - Volatile Writable Only ...................................................... 23 INSTRUCTIONS ............................................................................................................................. 24 8.1 8.2 Device ID and Instruction Set Tables ................................................................................. 24 8.1.1 Manufacturer and Device Identification ................................................................................ 24 8.1.2 Instruction Set Table 1 (Standard/Dual/Quad SPI, 3-Byte Address Mode)(1) ....................... 25 8.1.3 Instruction Set Table 2 (Dual/Quad SPI Instructions,3-Byte Address Mode) ....................... 26 8.1.4 Instruction Set Table 3 (Standard SPI, 4-Byte Address Mode)(1).......................................... 27 8.1.5 Instruction Set Table 4 (Dual/Quad SPI Instructions, 4-Byte Address Mode) ...................... 28 Instruction Descriptions ...................................................................................................... 30 8.2.1 Write Enable (06h) ............................................................................................................... 30 8.2.2 Write Enable for Volatile Status Register (50h) .................................................................... 30 8.2.3 Write Disable (04h) ............................................................................................................... 31 Figure 7. Write Disable Instruction for SPI Mode .............................................................................. 31 8.2.4 Read Status Register-1 (05h), Status Register-2 (35h) & Status Register-3 (15h) .............. 31 8.2.5 Write Status Register-1 (01h), Status Register-2 (31h) & Status Register-3 (11h) .............. 32 8.2.6 Read Extended Address Register (C8h) .............................................................................. 34 8.2.7 Write Extended Address Register (C5h) .............................................................................. 35 8.2.8 Enter 4-Byte Address Mode (B7h) ........................................................................................ 36 8.2.9 Exit 4-Byte Address Mode (E9h) .......................................................................................... 36 8.2.10 Read Data (03h) ................................................................................................................. 37 8.2.11 Read Data with 4-Byte Address (13h) ................................................................................ 38 8.2.12 Fast Read (0Bh) ................................................................................................................. 39 8.2.13 Fast Read with 4-Byte Address (0Ch) ................................................................................ 40 8.2.14 Fast Read Dual Output (3Bh) ............................................................................................. 41 8.2.15 Fast Read Dual Output with 4-Byte Address (3Ch) ............................................................ 42 8.2.16 Fast Read Quad Output (6Bh) ............................................................................................ 43 8.2.17 Fast Read Quad Output with 4-Byte Address (6Ch) ........................................................... 44 8.2.18 Fast Read Dual I/O (BBh) ................................................................................................... 45 8.2.19 Fast Read Dual I/O with 4-Byte Address (BCh) .................................................................. 46 8.2.20 Fast Read Quad I/O (EBh) ................................................................................................. 47 8.2.21 Fast Read Quad I/O with 4-Byte Address (ECh) ................................................................ 48 8.2.22 Set Burst with Wrap (77h) .................................................................................................. 49 8.2.23 Page Program (02h) ........................................................................................................... 50 8.2.24 Page Program with 4-Byte Address (12h) .......................................................................... 51 -2- Publication Release Date: October 23, 2018 Revision I W25Q256JV 9. 8.2.25 Quad Input Page Program (32h) ........................................................................................ 52 8.2.26 Quad Input Page Program with 4-Byte Address (34h) ....................................................... 53 8.2.27 Sector Erase (20h) ............................................................................................................. 54 8.2.28 Sector Erase with 4-Byte Address (21h)............................................................................. 55 8.2.29 32KB Block Erase (52h) ..................................................................................................... 56 8.2.30 64KB Block Erase (D8h) ..................................................................................................... 57 8.2.31 64KB Block Erase with 4-Byte Address (DCh) ................................................................... 58 8.2.32 Chip Erase (C7h / 60h) ....................................................................................................... 59 8.2.33 Erase / Program Suspend (75h) ......................................................................................... 60 8.2.34 Erase / Program Resume (7Ah) ......................................................................................... 61 8.2.35 Power-down (B9h) .............................................................................................................. 62 8.2.36 Release Power-down / Device ID (ABh) ............................................................................. 63 8.2.37 Read Manufacturer / Device ID (90h) ................................................................................. 64 8.2.38 Read Manufacturer / Device ID Dual I/O (92h) ................................................................... 65 8.2.39 Read Manufacturer / Device ID Quad I/O (94h) ................................................................. 66 8.2.40 Read Unique ID Number (4Bh)........................................................................................... 67 8.2.41 Read JEDEC ID (9Fh) ........................................................................................................ 68 8.2.42 Read SFDP Register (5Ah) ................................................................................................ 69 8.2.43 Erase Security Registers (44h) ........................................................................................... 70 8.2.44 Program Security Registers (42h) ...................................................................................... 71 8.2.45 Read Security Registers (48h) ........................................................................................... 72 8.2.46 Individual Block/Sector Lock (36h) ..................................................................................... 73 8.2.47 Individual Block/Sector Unlock (39h) .................................................................................. 74 8.2.48 Read Block/Sector Lock (3Dh) ........................................................................................... 75 8.2.49 Global Block/Sector Lock (7Eh) .......................................................................................... 76 8.2.50 Global Block/Sector Unlock (98h) ....................................................................................... 76 8.2.51 Enable Reset (66h) and Reset Device (99h) ...................................................................... 77 ELECTRICAL CHARACTERISTICS ............................................................................................... 78 9.1 Absolute Maximum Ratings (1) .......................................................................................... 78 9.2 Operating Ranges............................................................................................................... 78 9.3 Power-up Power-down Timing and Requirements ............................................................. 79 9.4 DC Electrical Characteristics .............................................................................................. 80 9.5 AC Measurement Conditions .............................................................................................. 81 9.6 AC Electrical Characteristics(6) ........................................................................................... 82 9.7 AC Electrical Characteristics (cont'd) .............................................................................. 83 9.8 Serial Output Timing ........................................................................................................... 84 9.9 Serial Input Timing .............................................................................................................. 84 9.1 /WP Timing ......................................................................................................................... 84 9.2 PACKAGE SPECIFICATIONs ............................................................................................ 85 9.3 8-Pad WFLGA 6x5-mm (Package Code M) ....................................................................... 85 9.4 8-Pad WSON 8x6-mm (Package Code E) ......................................................................... 86 -3- W25Q256JV 10. 9.5 16-Pin SOIC 300-mil (Package Code F) ............................................................................ 87 9.6 24-Ball TFBGA 8x6-mm (Package Code B, 5x5-1 Ball Array) ........................................... 88 9.7 24-Ball TFBGA 8x6-mm (Package Code C, 6x4 Ball Array) .............................................. 89 9.8 Ordering Information ........................................................................................................... 90 9.9 Valid Part Numbers and Top Side Marking ........................................................................ 91 REVISION IISTORY ....................................................................................................................... 93 -4- Publication Release Date: October 23, 2018 Revision I W25Q256JV 1. GENERAL DESCRIPTIONS The W25Q256JV (256M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1A for power-down. All devices are offered in space-saving packages. The W25Q256JV array is organized into 131,072 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q256JV has 8,192 erasable sectors and 512 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. The W25Q256JV supports the standard Serial Peripheral Interface (SPI), Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2, and I/O3. SPI clock frequencies of W25Q256JV of up to 133MHz are supported allowing equivalent clock rates of 266MHz (133MHz x 2) for Dual I/O and 532MHz (133MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. Additionally, the device supports JEDEC standard manufacturer and device ID and SFDP Register, a 64bit Unique Serial Number and three 256-bytes Security Registers. 2. FEATURES New Family of SpiFlash Memories - W25Q256JV: 256M-bit / 32M-byte - Standard SPI: CLK, /CS, DI, DO - Dual SPI: CLK, /CS, IO0, IO1, - Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3 - 3 or 4-Byte Addressing Mode - Software & Hardware Reset(1) Flexible Architecture with 4KB sectors - Uniform Sector/Block Erase (4K/32K/64K-Byte) - Program 1 to 256 byte per programmable page - Erase/Program Suspend & Resume Advanced Security Features - Software and Hardware Write-Protect - Power Supply Lock-Down - Special OTP protection - Top/Bottom, Complement array protection - Individual Block/Sector array protection - 64-Bit Unique ID for each device - Discoverable Parameters (SFDP) Register - 3X256-Bytes Security Registers with OTP locks - Volatile & Non-volatile Status Register Bits Highest Performance Serial Flash - 133MHz Standard/Dual/Quad SPI clocks - 266/532MHz equivalent Dual/Quad SPI - 66MB/S continuous data transfer rate - Min. 100K Program-Erase cycles per sector - More than 20-year data retention Efficient "Continuous Read" - Quad Peripheral Interface - Allows true XIP (execute in place) operation - Outperforms X16 Parallel Flash Low Power, Wide Temperature Range - Single 2.7 to 3.6V supply -<1A Power-down (typ.) - -40C to +85C operating range - -40C to +105C operating range Space Efficient Packaging(2) - 8-pad WSON 8x6-mm - 8-pad WFLGA 6x5-mm - 16-pin SOIC 300-mil (additional /Reset pin) - 24-ball TFBGA 8x6-mm(additional /Reset pin) - Contact Winbond for KGD and other options Note: 1. Hardware /RESET pin is only available on TFBGA or SOIC16 packages 2. Please contact Winbond for other packages. -5- W25Q256JV 3. PACKAGE TYPES AND PIN CONFIGURATIONS 3.1 Pad Configuration WSON 8x6-mm, WFLGA 6x5-mm Top View /CS 1 8 VCC DO (IO1) 2 7 /HOLD or /RESET (IO3) /WP (IO2) 3 6 CLK GND 4 5 DI (IO0) Figure 1a. W25Q256JV Pad Assignments, 8-pad WSON 8x6-mm (Package Code E & M) 3.2 Pad Description WSON 8x6-mm, WFLGA 6x5-mm PAD NO. PAD NAME I/O FUNCTION 1 /CS I 2 DO (IO1) I/O Data Output (Data Input Output 1)(1) 3 /WP (IO2) I/O Write Protect Input ( Data Input Output 2)(2) 4 GND 5 DI (IO0) I/O 6 CLK I 7 /HOLD or /RESET (IO3) I/O 8 VCC Chip Select Input Ground Data Input (Data Input Output 0)(1) Serial Clock Input Hold or Reset Input (Data Input Output 3)(2) Power Supply Notes: 1. 2. IO0 and IO1 are used for Standard and Dual SPI instructions IO0 - IO3 are used for Quad SPI instructions, /HOLD (or /RESET) function is only available for Standard/Dual SPI. -6- Publication Release Date: October 23, 2018 Revision I W25Q256JV 3.3 Pin Configuration SOIC 300-mil Figure 1b. W25Q256JV Pin Assignments, 16-pin SOIC 300-mil (Package Code F) 3.4 Pin Description SOIC 300-mil PIN NO. PIN NAME I/O FUNCTION 1 /HOLD or /RESET (IO3) I/O 2 VCC 3 /RESET 4 N/C No Connect 5 N/C No Connect 6 N/C No Connect 7 /CS I 8 DO (IO1) I/O Data Output (Data Input Output 1)(1) 9 /WP (IO2) I/O Write Protect Input (Data Input Output 2)(2) 10 GND Ground 11 N/C No Connect 12 N/C No Connect 13 N/C No Connect 14 N/C No Connect 15 DI (IO0) I/O 16 CLK I Hold or Reset Input (Data Input Output 3)(2) Power Supply I Reset Input(3) Chip Select Input Data Input (Data Input Output 0)(1) Serial Clock Input Notes: 1. IO0 and IO1 are used for Standard and Dual SPI instructions. 2. IO0 - IO3 are used for Quad SPI instructions, /HOLD (or /RESET) function is only available for Standard/Dual SPI. 3. The /RESET pin is a dedicated hardware reset pin regardless of device settings or operation states. If the hardware reset function is not used, this pin can be left floating or connected to VCC in the system. -7- W25Q256JV 3.5 Ball Configuration TFBGA 8x6-mm (5x5 or 6x4 Ball Array) Top View Top View A2 A3 A4 A5 A1 A2 A3 A4 NC NC NC /RESET NC NC /RESET NC B1 B2 B3 B4 B1 B2 B3 B4 B5 NC CLK GND VCC NC CLK GND VCC NC C1 C2 C3 C4 C1 C2 C3 C4 C5 NC /CS NC /WP (IO2) NC /CS NC /WP (IO2) NC D1 D2 D3 D4 D1 D2 D3 D4 D5 NC DO(IO1) NC DO(IO1) NC E1 E2 E3 E4 E1 E2 E3 E4 E5 NC NC NC NC NC NC NC NC NC DI(IO0) /HOLD(IO3) Package Code B DI(IO0) /HOLD(IO3) F1 F2 F3 F4 NC NC NC NC Package Code C Figure 1c. W25Q256JV Ball Assignments, 24-ball TFBGA 6x8-mm (Package Code B & C) 3.6 Ball Description TFBGA 8x6-mm BALL NO. PIN NAME I/O FUNCTION A4 /RESET I Reset Input(3) B2 CLK I Serial Clock Input B3 GND Ground B4 VCC Power Supply C2 /CS I C4 /WP (IO2) I/O Write Protect Input (Data Input Output 2)(2) D2 DO (IO1) I/O Data Output (Data Input Output 1)(1) D3 DI (IO0) I/O Data Input (Data Input Output 0)(1) D4 /HOLD (IO3) I/O Hold or Reset Input (Data Input Output 3)(2) Multiple NC Chip Select Input No Connect Notes: 1. 2. 3. IO0 and IO1 are used for Standard and Dual SPI instructions IO0 - IO3 are used for Quad SPI instructions, /HOLD (or /RESET) function is only available for Standard/Dual SPI. The /RESET pin is a dedicated hardware reset pin regardless of device settings or operation states. If the hardware reset function is not used, this pin can be left floating or connected to VCC in the system -8- Publication Release Date: October 23, 2018 Revision I W25Q256JV 4. PIN DESCRIPTIONS 4.1 Chip Select (/CS) The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When deselected, the devices power consumption will be at standby levels unless an internal erase, program or write status register cycle is in progress. When /CS is brought low the device will be selected, power consumption will increase to active levels and instructions can be written to and data read from the device. After power-up, /CS must transition from high to low before a new instruction will be accepted. The /CS input must track the VCC supply level at power-up and power-down (see "Write Protection" and Figure 58). If needed a pull-up resistor on the /CS pin can be used to accomplish this. 4.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) The W25Q256JV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read data or status from the device on the falling edge of CLK. Dual and Quad SPI instructions use the bidirectional IO pins to serially write instructions, addresses or data to the device on the rising edge of CLK and read data or status from the device on the falling edge of CLK. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set. When QE=1, the /WP pin becomes IO2 and the /HOLD pin becomes IO3. 4.3 Write Protect (/WP) The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in conjunction with the Status Register's Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits and Status Register Protect (SRP) bits, a portion as small as a 4KB sector or the entire memory array can be hardware protected. The /WP pin is active low. 4.4 HOLD (/HOLD) The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low, while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored (don't care). When /HOLD is brought high, device operation can resume. The /HOLD function can be useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is used for IO3. See Figure 1a-c for the pin configuration of Quad I/O operation. 4.5 Serial Clock (CLK) The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI Operations") 4.6 Reset (/RESET)(1) A dedicated hardware /RESET pin is available on SOIC-16 and TFBGA packages. When it's driven low for a minimum period of ~1S, this device will terminate any external or internal operations and return to its power-on state. Note: Hardware /RESET pin is available on SOIC-16 or TFBGA; please contact Winbond for this package. -9- W25Q256JV 5. BLOCK DIAGRAM Figure 2. W25Q256JV Serial Flash Memory Block Diagram - 10 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 6. FUNCTIONAL DESCRIPTIONS 6.1 SPI Operations Power Up Device Initialization & Status Register Refresh ( Non- Volatile Cells) ADP = 0 ADP bit value 3- Byte Address ADP = 1 4- Byte Address Enable 4- Byte (B7h) Hardware Reset Standard SPI Dual SPI Quad SPI Disable 4- Byte (E9h) Standard SPI Dual SPI Quad SPI SPI Reset (66 h + 99h) Figure 3. W25Q256JV Serial Flash Memory Operation Diagram 6.1.1 Standard SPI Instructions The W25Q256JV is accessed through an SPI compatible bus consisting of four signals: Serial Clock (CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of CLK. The DO output pin is used to read data or status from the device on the falling edge of CLK. SPI bus operation Mode 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is not being transferred to the Serial Flash. For Mode 0, the CLK signal is normally low on the falling and rising edges of /CS. For Mode 3, the CLK signal is normally high on the falling and rising edges of /CS. 6.1.2 Dual SPI Instructions The W25Q256JV supports Dual SPI operation when using instructions such as "Fast Read Dual Output (3Bh)" and "Fast Read Dual I/O (BBh)". These instructions allow data to be transferred to or from the device at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal for quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speedcritical code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins become bidirectional I/O pins: IO0 and IO1. 6.1.3 Quad SPI Instructions The W25Q256JV supports Quad SPI operation when using instructions such as "Fast Read Quad Output (6Bh)", and "Fast Read Quad I/O (EBh)". These instructions allow data to be transferred to or from the device four to six times the rate of ordinary Serial Flash. The Quad Read instructions offer a significant improvement in random access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP). When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set. - 11 - W25Q256JV 6.1.4 3-Byte / 4-Byte Address Modes The W25Q256JV provides two Address Modes that can be used to specify any byte of data in the memory array. The 3-Byte Address Mode is backward compatible to older generations of serial flash memory that only support up to 128M-bit data. To address the 256M-bit or more data in 3-Byte Address Mode, Extended Address Register must be used in addition to the 3-Byte addresses. 4-Byte Address Mode is designed to support Serial Flash Memory devices from 256M-bit to 32G-bit. The extended Address Register is not necessary when the 4-Byte Address Mode is enabled. Upon power up, the W25Q256JV can operate in either 3-Byte Address Mode or 4-Byte Address Mode, depending on the Non-Volatile Status Register Bit ADP (S17) setting. If ADP=0, the device will operate in 3-Byte Address Mode; if ADP=1, the device will operate in 4-Byte Address Mode. The factory default value for ADP is 0. To switch between the 3-Byte or 4-Byte Address Modes, "Enter 4-Byte Mode (B7h)" or "Exit 4-Byte Mode (E9h)" instructions must be used. The current address mode is indicated by the Status Register Bit ADS (S16). W25Q256JV also supports a set of basic SPI instructions which requires dedicated 4-Byte address regardless the device Address Mode setting. Please refer to Instruction Set Table 2 for details. 6.1.5 Software Reset & Hardware /RESET pin The W25Q256JV can be reset to the initial power-on state by a software Reset sequence in SPI mode. This sequence must include two consecutive commands: Enable Reset (66h) & Reset (99h). If the command sequence is successfully accepted, the device will take approximately 30uS ( tRST) to reset. No command will be accepted during the reset period. For the SOIC-16 and TFBGA package, W25Q256JV provides a dedicated /RESET pin. Drive the /RESET pin low for a minimum period of ~1us (tRESET*) will reset the device to its initial power-on state. Hardware /RESET pin has the highest priority among all the input signals. Drive /RESET low for a minimum period of ~1us (tRESET*) will interrupt any on-going external/internal operations, regardless the status of other SPI signals (/CS, CLK, IOs). Note: 1. While a faster /RESET pulse (as short as a few hundred nanoseconds) will often reset the device, a 1us minimum pulse is recommended to ensure reliable operation. 2. There is an internal pull-up resistor for the dedicated /RESET pin on the SOIC-16 package. If the reset function is not used, this pin can be left floating in the system. - 12 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 6.2 Write Protection Applications that use non-volatile memory must take into consideration the possibility of noise and other adverse system conditions that may compromise data integrity. To address this concern, the W25Q256JV provides several means to protect the data from inadvertent writes. Device resets when VCC is below threshold Time delay write disable after Power-up Write enable/disable instructions and automatic write disable after erase or program Software and Hardware (/WP pin) write protection using Status Registers Additional Individual Block/Sector Locks for array protection Write Protection using Power-down instruction Lock Down write protection for Status Register until the next power-up One Time Program (OTP) write protection for array and Security Registers using Status Register * * Note: This feature is available upon special order. Please contact Winbond for details. Upon power-up or at power-down, the W25Q256JV will maintain a reset condition while VCC is below the threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 43). While reset, all operations are disabled and no instructions are recognized. During power-up and after the VCC voltage exceeds VWI, all program and erase related instructions are further disabled for a time delay of t PUW . This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until the VCC-min level and tVSL time delay is reached, and it must also track the VCC supply level at powerdown to prevent adverse command sequence. If needed, a pull-up resistor on /CS pin can be used to accomplish this. After power-up the device is automatically placed in a write-disabled state with the Status Register Write Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a writedisabled state of 0. Software controlled write protection is facilitated using the Write Status Register instruction and setting the Status Register Protect (SRP, SRL) and Block Protect (CMP, TB, BP[3:0]) bits. These settings allow a portion or the entire memory array to be configured as read only. Used in conjunction with the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware control. See Status Register section for further information. Additionally, the Power-down instruction offers an extra level of write protection as all instructions are ignored except for the Release Power-down instruction. The W25Q256JV also provides another Write Protect method using the Individual Block Locks. Each 64KB block (except the top and bottom blocks, total of 510 blocks) and each 4KB sector within the top/bottom blocks (total of 32 sectors) are equipped with an Individual Block Lock bit. When the lock bit is 0, the corresponding sector or block can be erased or programmed; when the lock bit is set to 1, Erase or Program commands issued to the corresponding sector or block will be ignored. When the device is powered on, all Individual Block Lock bits will be 1, so the entire memory array is protected from Erase/Program. An "Individual Block Unlock (39h)" instruction must be issued to unlock any specific sector or block. The WPS bit in Status Register-3 is used to decide which Write Protect scheme should be used. When WPS=0 (factory default), the device will only utilize CMP, TB, BP[3:0] bits to protect specific areas of the array; when WPS=1, the device will utilize the Individual Block Locks for write protection. - 13 - W25Q256JV 7. STATUS AND CONFIGURATION REGISTERS Three Status and Configuration Registers are provided for W25Q256JV. The Read Status Register-1/2/3 instructions can be used to provide status on the availability of the flash memory array, whether the device is write enabled or disabled, the state of write protection, Quad SPI setting, Security Register lock status, Erase/Program Suspend status, output driver strength, power-up and current Address Mode. The Write Status Register instruction can be used to configure the device write protection features, Quad SPI setting, Security Register OTP locks functions, output driver strength and power-up Address Mode. Write access to the Status Register is controlled by the state of the non-volatile Status Register Lock bits (SRL), and the Write Enable instruction. 7.1 Status Registers S7 S6 S5 S4 S3 S2 S1 S0 SRP TB BP 3 BP2 BP1 BP0 WEL BUSY Status Register Protect (Volatile/Non-Volatile Writable) Top/Bottom Protect Bit (Volatile/Non-Volatile Writable) Block Protect Bits (Volatile/Non-Volatile Writable) Write Enable Latch (Status-Only) Erase/Write In Progress s (Status-Only) s Figure 4a. Status Register-1 7.1.1 Erase/Write In Progress (BUSY) - Status Only BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or Erase/Program Security Register instruction. During this time the device will ignore further instructions except for the Read Status Register and Erase/Program Suspend instruction (see tW , tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status/security register instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions. 7.1.2 Write Enable Latch (WEL) - Status Only Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Erase Security Register and Program Security Register. - 14 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 7.1.3 Block Protect Bits (BP3, BP2, BP1, BP0) - Volatile/Non-Volatile Writable The Block Protect Bits (BP3, BP2, BP1, BP0) are non-volatile read/write bits in the status register (S5, S4, S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using the Write Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be protected from Program and Erase instructions (see Status Register Memory Protection table). The factory default setting for the Block Protection Bits is 0, none of the array protected. 7.1.4 Top/Bottom Block Protect (TB) - Volatile/Non-Volatile Writable The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP3, BP2, BP1, BP0) protect from the Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction depending on the state of the WEL bits. 7.1.5 Complement Protect (CMP) - Volatile/Non-Volatile Writable The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in conjunction with TB, BP3, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once CMP is set to 1, previous array protection set by TB, BP3, BP2, BP1 and BP0 will be reversed. For instance, when CMP=0, a top 64KB block can be protected while the rest of the array is not; when CMP=1, the top 64KB block will become unprotected while the rest of the array become read-only. Please refer to the Status Register Memory Protection table for details. The default setting is CMP=0. - 15 - W25Q256JV Status Register Protect (SRP, SRL) - Volatile/Non-Volatile Writable 7.1.1 Three Status and Configuration Registers are provided for W25Q256JV. The Read Status Register-1/2/3 instructions can be used to provide status on the availability of the flash memory array, whether the device is write enabled or disabled, the state of write protection, Quad SPI setting, Security Register lock status, Erase/Program Suspend status, and output driver strength, The Write Status Register instruction can be used to configure the device write protection features, Quad SPI setting, Security Register OTP locks, output driver. Write access to the Status Register is controlled by the state of the non-volatile Status Register Protect bits (SRP, SRL), the Write Enable instruction, and during Standard/Dual SPI operations, the /WP pin. SRL SRP /WP Status Register Description 0 0 X Software Protection /WP pin has no control. The Status register can be written to after a Write Enable instruction, WEL=1. [Factory Default] 0 1 0 Hardware Protected When /WP pin is low the Status Register locked and cannot be written to. 0 1 1 Hardware Unprotected When /WP pin is high the Status register is unlocked and can be written to after a Write Enable instruction, WEL=1. 1 X X Power Supply Lock-Down Status Register is protected and cannot be written to again until the next power-down, power-up cycle.(1) 1 X X One Time Program(2) Status Register is permanently protected and cannot be written to. (enabled by adding prefix command AAh, 55h) 1. When SRL =1, a power-down, power-up cycle will change SRL =0 state. 2. Please contact Winbond for details regarding the special instruction sequence. - 16 - Publication Release Date: October 23, 2018 Revision I W25Q256JV S15 S14 S13 S12 S11 S10 S9 S8 SUS CMP LB3 LB2 LB1 (R ) QE SRL Suspend Status (Status- Only) Complement Protect ( Volatile/Non- Volatile Writable) Security Register Lock Bits ( Volatile/Non- Volatile OTP Writable) Reserved Quad Enable ( Volatile/Non- Volatile Writable) Status Register Protect 1 ( Volatile/Non- Volatile Writable) Figure 4b. Status Register-2 7.1.2 Erase/Program Suspend Status (SUS) - Status Only The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing a Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume (7Ah) instruction as well as a power-down, power-up cycle. 7.1.3 Security Register Lock Bits (LB3, LB2, LB1) - Volatile/Non-Volatile OTP Writable The Security Register Lock Bits (LB3, LB2, LB1) are non-volatile One Time Program (OTP) bits in Status Register (S13, S12, S11) that provide the write protect control and status to the Security Registers. The default state of LB3-1 is 0, Security Registers are unlocked. LB3-1 can be set to 1 individually using the Write Status Register instruction. LB3-1 are One Time Programmable (OTP), once it's set to 1, the corresponding 256-Byte Security Register will become read-only permanently. 7.1.4 Quad Enable (QE) - Volatile/Non-Volatile Writable The Quad Enable (QE) bit is a non-volatile read/write bit in the status register (S9) that enables Quad SPI operation. When the QE bit is set to a 0 state (factory default for part numbers with ordering options "IM" & "JM"), the /HOLD are enabled, the device operates in Standard/Dual SPI modes. When the QE bit is set to a 1 (factory fixed default for part numbers with ordering options "IQ" & "JQ"), the Quad IO2 and IO3 pins are enabled, and /HOLD function is disabled, the device operates in Standard/Dual/Quad SPI modes. - 17 - W25Q256JV S23 (R) S22 S21 DRV1 DRV0 S20 S19 S18 S17 S16 (R) (R) WPS ADP ADS Reserved Output Driver Strength (Volatile/Non-Volatile Writable) Reserved Write Protect Selection (Volatile/Non-Volatile Writable) Power Up Address Mode (Non-Volatile Writable) Current Address Mode (Status-Only) Figure 4c. Status Register-3 7.1.5 Current Address Mode (ADS) - Status Only The Current Address Mode bit is a read only bit in the Status Register-3 that indicates which address mode the device is currently operating in. When ADS=0, the device is in the 3-Byte Address Mode, when ADS=1, the device is in the 4-Byte Address Mode. 7.1.6 Power-Up Address Mode (ADP) - Non-Volatile Writable The ADP bit is a non-volatile bit that determines the initial address mode when the device is powered on or reset. This bit is only used during the power on or device reset initialization period, and it is only writable by the non-volatile Write Status sequence (06h + 11h). When ADP=0 (factory default), the device will power up into 3-Byte Address Mode, the Extended Address Register must be used to access memory regions beyond 128Mb. When ADP=1, the device will power up into 4-Byte Address Mode directly. 7.1.7 Write Protect Selection (WPS) - Volatile/Non-Volatile Writable The WPS bit is used to select which Write Protect scheme should be used. When WPS=0, the device will use the combination of CMP, TB, BP[3:0] bits to protect a specific area of the memory array. When WPS=1, the device will utilize the Individual Block Locks to protect any individual sector or blocks. The default value for all Individual Block Lock bits is 1 upon device power on or after reset. - 18 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 7.1.8 Output Driver Strength (DRV1, DRV0) - Volatile/Non-Volatile Writable The DRV1 & DRV0 bits are used to determine the output driver strength for the Read operations. 7.1.9 DRV1, DRV0 Driver Strength 0, 0 100% 0, 1 75% 1, 0 50% 1, 1 25% (default setting) Reserved Bits - Non Functional There are a few reserved Status Register bits that may be read out as a "0" or "1". It is recommended to ignore the values of those bits. During a "Write Status Register" instruction, the Reserved Bits can be written as "0", but there will not be any effects. - 19 - W25Q256JV 7.1.10 W25Q256JV Status Register Memory Protection (WPS = 0, CMP = 0) STATUS REGISTER(1) W25Q256JV (256M-BIT / 32M-BYTE) MEMORY PROTECTION(2) TB BP3 BP2 BP1 BP0 PROTECTED BLOCK(S) PROTECTED ADDRESSES PROTECTED DENSITY PROTECTED PORTION X 0 0 0 0 NONE NONE NONE NONE 0 0 0 0 1 511 01FF0000h - 01FFFFFFh 64KB Upper 1/512 0 0 0 1 0 510 thru 511 01FE0000h - 01FFFFFFh 128KB Upper 1/256 0 0 0 1 1 508 thru 511 01FC0000h - 01FFFFFFh 256KB Upper 1/128 0 0 1 0 0 504 thru 511 01F80000h - 01FFFFFFh 512KB Upper 1/64 0 0 1 0 1 496 thru 511 01F00000h - 01FFFFFFh 1MB Upper 1/32 0 0 1 1 0 480 thru 511 01E00000h - 01FFFFFFh 2MB Upper 1/16 0 0 1 1 1 448 thru 511 01C00000h - 01FFFFFFh 4MB Upper 1/8 0 1 0 0 0 384 thru 511 01800000h - 01FFFFFFh 8MB Upper 1/4 0 1 0 0 1 256 thru 511 01000000h - 01FFFFFFh 16MB Upper 1/2 1 0 0 0 1 0 00000000h - 0000FFFFh 64KB Lower 1/512 1 0 0 1 0 0 thru 1 00000000h - 0001FFFFh 128KB Lower 1/256 1 0 0 1 1 0 thru 3 00000000h - 0003FFFFh 256KB Lower 1/128 1 0 1 0 0 0 thru 7 00000000h - 0007FFFFh 512KB Lower 1/64 1 0 1 0 1 0 thru 15 00000000h - 000FFFFFh 1MB Lower 1/32 1 0 1 1 0 0 thru 31 00000000h - 001FFFFFh 2MB Lower 1/16 1 0 1 1 1 0 thru 63 00000000h - 003FFFFFh 4MB Lower 1/8 1 1 0 0 0 0 thru 127 00000000h - 007FFFFFh 8MB Lower 1/4 1 1 0 0 1 0 thru 255 00000000h - 00FFFFFFh 16MB Lower 1/2 X 1 1 0 X 0 thru 511 00000000h - 01FFFFFFh 32MB ALL X 1 X 1 X 0 thru 511 00000000h - 01FFFFFFh 32MB ALL Notes: 1. X = don't care 2. If any Erase or Program command specifies a memory region that contains protected data portion, this command will be ignored. - 20 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 7.1.11 W25Q256JV Status Register Memory Protection (WPS = 0, CMP = 1) STATUS REGISTER(1) W25Q256JV (256M-BIT / 32M-BYTE) MEMORY PROTECTION(2) TB BP3 BP2 BP1 BP0 PROTECTED BLOCK(S) PROTECTED ADDRESSES PROTECTED DENSITY PROTECTED PORTION X 0 0 0 0 ALL 00000000h - 01FFFFFFh ALL ALL 0 0 0 0 1 0 thru 510 00000000h - 01FEFFFFh 32,704KB Lower 511/512 0 0 0 1 0 0 thru 509 00000000h - 01FDFFFFh 32,640KB Lower 255/256 0 0 0 1 1 0 thru 507 00000000h - 01FBFFFFh 32,512KB Lower 127/128 0 0 1 0 0 0 thru 503 00000000h - 01F7FFFFh 32,256KB Lower 63/64 0 0 1 0 1 0 thru 495 00000000h - 01EFFFFFh 31MB Lower 31/32 0 0 1 1 0 0 thru 479 00000000h - 01DFFFFFh 30MB Lower 15/16 0 0 1 1 1 0 thru 447 00000000h - 01BFFFFFh 28MB Lower 7/8 0 1 0 0 0 0 thru 383 00000000h - 017FFFFFh 24MB Lower 3/4 0 1 0 0 1 0 thru 255 00000000h - 00FFFFFFh 16MB Lower 1/2 1 0 0 0 1 1 thru 511 00010000h - 01FFFFFFh 32,704KB Upper 511/512 1 0 0 1 0 2 thru 511 00020000h - 01FFFFFFh 32,640KB Upper 255/256 1 0 0 1 1 4 thru 511 00040000h - 01FFFFFFh 32,512KB Upper 127/128 1 0 1 0 0 8 thru 511 00080000h - 01FFFFFFh 32,256KB Upper 63/64 1 0 1 0 1 16 thru 511 00100000h - 01FFFFFFh 31MB Upper 31/32 1 0 1 1 0 32 thru 511 00200000h - 01FFFFFFh 30MB Upper 15/16 1 0 1 1 1 64 thru 511 00400000h - 01FFFFFFh 28MB Upper 7/8 1 1 0 0 0 128 thru 511 00800000h - 01FFFFFFh 24MB Upper 3/4 1 1 0 0 1 256 thru 511 01000000h - 01FFFFFFh 16MB Upper 1/2 X 1 1 0 X NONE NONE NONE NONE X 1 X 1 X NONE NONE NONE NONE Notes: 1. X = don't care 2. If any Erase or Program command specifies a memory region that contains protected data portion, this command will be ignored. - 21 - W25Q256JV W25Q256JV Individual Block Memory Protection (WPS=1) Block 511 (64KB) 7.1.12 Sector 15 (4KB) Sector 14 (4KB) Sector 1 (4KB) Sector 0 (4KB) Individual Block Locks: 32 Sectors (Top/Bottom) 510 Blocks Block 510 (64KB) Individual Block Lock: 36h + Address Individual Block Unlock: 39h + Address Read Block Lock: 3Dh + Address Global Block Lock: 7Eh Block 0 (64KB) Block 1 (64KB) Global Block Unlock: 98h Sector 15 (4KB) Sector 14 (4KB) Sector 1 (4KB) Sector 0 (4KB) Figure 4d. Individual Block/Sector Locks Notes: 1. Individual Block/Sector protection is only valid when WPS=1. 2. All individual block/sector lock bits are set to 1 by default after power up, all memory array is protected. - 22 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 7.2 Extended Address Register - Volatile Writable Only In addition to the Status Registers, W25Q256JV provides a volatile Extended Address Register which consists of the 4th byte of memory address. The Extended Address Register is used only when the device is operating in the 3-Byte Address Mode (ADS=0). The lower 128Mb memory array (00000000h - 00FFFFFFh) is selected when A24=0, all instructions with 3-Byte addresses will be executed within that region. When A24=1, the upper 128Mb memory array (01000000h - 01FFFFFFh) will be selected. If the device powers up with ADP bit set to 1, or an "Enter 4-Byte Address Mode (B7h)" instruction is issued, the device will require 4-Byte address input for all address related instructions, and the Extended Address Register setting will be ignored. However, any command with 4-byte address input will replace the Extended Address Register Bits (A31-A24) with new settings. Upon power up or after the execution of a Software/Hardware Reset, the Extended Address Register values will be cleared to 0. EA7 EA6 EA5 EA4 EA3 EA2 EA1 EA0 A31 A30 A29 A28 A27 A26 A25 A24 Reserved for higher densities 512Mb ~ 32Gb (Volatile Writable Only) Address Bit #24 A24=0: Select lower 128Mb A24=1: Select upper 128Mb (Volatile Writable Only) Figure 4e. Extended Address Register - 23 - W25Q256JV 8. INSTRUCTIONS The Standard/Dual/Quad SPI instruction set of the W25Q256JV consists of 48 basic instructions that are fully controlled through the SPI bus (see Instruction Set Table1-4). Instructions are initiated with the falling edge of Chip Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the DI input is sampled on the rising edge of clock with most significant bit (MSB) first. Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data bytes, dummy bytes (don't care), and in some cases, a combination. Instructions are completed with the rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in Figures 5 through 57. All read instructions can be completed after any clocked bit. However, all instructions that Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been clocked) otherwise the instruction will be ignored. This feature further protects the device from inadvertent writes. Additionally, while the memory is being programmed or erased, or when the Status Register is being written, all instructions except for Read Status Register will be ignored until the program or erase cycle has completed. 8.1 8.1.1 Device ID and Instruction Set Tables Manufacturer and Device Identification MANUFACTURER ID (MF7 - MF0) Winbond Serial Flash EFh Device ID (ID7 - ID0) (ID15 - ID0) Instruction ABh, 90h, 92h, 94h 9Fh W25Q256JV-IQ/JQ 18h 4019h W25Q256JV-IM*/JM* 18h 7019h Note: For DTR, QPI supporting, please refer to W25Q256JV DTR datasheet. - 24 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.1.2 Instruction Set Table 1 (Standard/Dual/Quad SPI, 3-Byte Address Mode)(1) Data Input Output Number of Clock(1-1-1) Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 8 8 8 8 8 8 8 Write Enable 06h Volatile SR Write Enable 50h Write Disable 04h Release Power-down / ID ABh Dummy Dummy Dummy (ID7-ID0)(2) Manufacturer/Device ID 90h Dummy Dummy 00h (MF7-MF0) (ID7-ID0) JEDEC ID 9Fh (MF7-MF0) (ID15-ID8) (ID7-ID0) Read Unique ID 4Bh Dummy Dummy Dummy Dummy (UID63-0) Read Data 03h A23-A16 A15-A8 A7-A0 (D7-D0) Read Data with 4-Byte Address 13h A31-A24 A23-A16 A15-A8 A7-A0 (D7-D0) Fast Read 0Bh A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Fast Read with 4-Byte Address 0Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy Page Program 02h A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Page Program with 4-Byte Address 12h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 Sector Erase (4KB) 20h A23-A16 A15-A8 A7-A0 Sector Erase (4KB) with 4-Byte Address 21h A31-A24 A23-A16 A15-A8 Block Erase (32KB) 52h A23-A16 A15-A8 A7-A0 Block Erase (64KB) D8h A23-A16 A15-A8 A7-A0 Block Erase (64KB) with 4-Byte Address DCh A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Chip Erase A7-A0 C7h/60h 05h (S7-S0)(2) Write Status Register-1 01h (S7-S0)(4) Read Status Register-2 35h (S15-S8)(2) Write Status Register-2 31h (S15-S8) Read Status Register-3 15h (S23-S16)(2) Read Status Register-1 (4) Write Status Register-3 11h (S23-S16) Read Extended Addr. Reg. C8h (EA7-EA0)(2) Write Extended Addr. Reg. C5h (EA7-EA0) Read SFDP Register 5Ah A23-A16 A15-A8 A7-A0 Erase Security Register(5) 44h A23-A16 A15-A8 A7-A0 Program Security Register(5) 42h A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Read Security Register(5) 48h A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Global Block Lock 7Eh (L7-L0) Global Block Unlock 98h Read Block Lock 3Dh A23-A16 A15-A8 A7-A0 Individual Block Lock 36h A23-A16 A15-A8 A7-A0 Individual Block Unlock 39h A23-A16 A15-A8 A7-A0 Erase / Program Suspend 75h Erase / Program Resume 7Ah Power-down B9h Enter 4-Byte Address Mode B7h Exit 4-Byte Address Mode E9h Enable Reset 66h Reset Device 99h - 25 - (D7-D0) D7-D0(3) W25Q256JV 8.1.3 Instruction Set Table 2 (Dual/Quad SPI Instructions,3-Byte Address Mode) Data Input Output Number of Clock(1-1-2) Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 Byte 9 Byte 10 8 8 8 8 8 4 4 4 4 4 (7) 3Bh A23-A16 A15-A8 A7-A0 Dummy Fast Read Dual Output with 4-Byte Address 3Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy Dummy (D7-D0)(7) ... Number of Clock(1-2-2) 8 4 4 4 4 4 4 4 4 4 Mftr./Device ID Dual I/O 92h A23-A16 A15-A8 0 Dummy(11) (MF7-MF0) (ID7-ID0) Fast Read Dual I/O BBh A23-A16 A15-A8 A7-A0 Dummy(11) (D7-D0) ... Fast Read Dual I/O with 4-Byte Address BCh A31-A24 A23-A16 A15-A8 A7-A0 Dummy(11) (D7-D0) ... 8 8 8 8 2 2 2 2 2 2 32h A23-A16 A15-A8 A7-A0 (D7-D0)(9) (D7-D0)(3) ... 34h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 ... ... Fast Read Quad Output 6Bh A23-A16 A15-A8 A7-A0 Dummy Dummy Dummy Dummy (D7-D0)(9) ... Number of Clock(1-1-4) 8 8 8 8 8 2 2 2 2 2 Fast Read Quad Output with 4-Byte Address 6Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy Dummy Dummy Dummy (D7-D0)(9) Number of Clock(1-4-4) 8 2 2 2 2 2 2 2 2 2 Mftr./Device ID Quad I/O 94h A23-A16 A15-A8 0 Dummy(11) Dummy Dummy (MF7-MF0) (ID7-ID0) Fast Read Quad I/O EBh A23-A16 A15-A8 A7-A0 Dummy(11) Dummy Dummy (D7-D0) ... Fast Read Quad I/O with 4-Byte Address ECh A31-A24 A23-A16 A15-A8 A7-A0f Dummy(11) Dummy Dummy (D7-D0) Set Burst with Wrap 77h Dummy Dummy Dummy W7-W0 Number of Clock(1-1-4) Quad Input Page Program Quad Page Program with 4-Byte Address - 26 - (D7-D0) ... Fast Read Dual Output Publication Release Date: October 23, 2018 Revision I ... W25Q256JV 8.1.4 Instruction Set Table 3 (Standard SPI, 4-Byte Address Mode)(1) Data Input Output Number of Clock(1-1-1) Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 8 8 8 8 8 8 8 Write Enable 06h Volatile SR Write Enable 50h Write Disable 04h Release Power-down / ID ABh Dummy Dummy Dummy (ID7-ID0)(2) Manufacturer/Device ID 90h Dummy Dummy 00h (MF7-MF0) JEDEC ID 9Fh (MF7-MF0) (ID15-ID8) (ID7-ID0) Read Unique ID 4Bh Dummy Dummy Dummy Dummy Dummy Read Data 03h A31-A24 A23-A16 A15-A8 A7-A0 (D7-D0) Read Data with 4-Byte Address 13h A31-A24 A23-A16 A15-A8 A7-A0 (D7-D0) Fast Read 0Bh A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Fast Read with 4-Byte Address 0Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Page Program 02h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Page Program with 4-Byte Address 12h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Sector Erase (4KB) 20h A31-A24 A23-A16 A15-A8 A7-A0 Sector Erase (4KB) with 4-Byte Address 21h A31-A24 A23-A16 A15-A8 A7-A0 Block Erase (32KB) 52h A31-A24 A23-A16 A15-A8 A7-A0 Block Erase (64KB) D8h A31-A24 A23-A16 A15-A8 A7-A0 Block Erase (64KB) with 4-Byte Address DCh A31-A24 A23-A16 A15-A8 A7-A0 Chip Erase (ID7-ID0) (UID63-0) C7h/60h Read Status Register-1 05h (S7-S0)(2) Write Status Register-1(4) 01h (S7-S0)(4) Read Status Register-2 35h (S15-S8)(2) Write Status Register-2 31h (S15-S8) Read Status Register-3 15h (S23-S16)(2) Write Status Register-3 11h (S23-S16) Read Extended Addr. Reg. C8h (EA7-EA0)(2) Write Extended Addr. Reg. C5h (EA7-EA0) Read SFDP Register 5Ah A23-A16 A15-A8 A7-A0 Dummy Erase Security Register(5) 44h A31-A24 A23-A16 A15-A8 A7-A0 Program Security Register(5) 42h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Read Security Register(5) 48h A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Global Block Lock 7Eh (L7-L0) Global Block Unlock 98h Read Block Lock 3Dh A31-A24 A23-A16 A15-A8 A7-A0 Individual Block Lock 36h A31-A24 A23-A16 A15-A8 A7-A0 Individual Block Unlock 39h A31-A24 A23-A16 A15-A8 A7-A0 Erase / Program Suspend 75h Erase / Program Resume 7Ah Power-down B9h Enter 4-Byte Address Mode B7h Exit 4-Byte Address Mode E9h Enable Reset 66h Reset Device 99h - 27 - (D7-D0) W25Q256JV 8.1.5 Instruction Set Table 4 (Dual/Quad SPI Instructions, 4-Byte Address Mode) Data Input Output Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 4 Number of Clock(1-1-2) 8 8 8 8 8 8 4 Fast Read Dual Output 3Bh A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0,...)(7) Fast Read Dual Output with 4-Byte Address 3Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy (D7-D0,...)(7) Number of Clock(1-2-2) 8 4 4 4 4 4 4 4 (MF7-MF0) (ID7-ID0) (11) Mftr./Device ID Dual I/O 92h A31-A24 A23-A16 A15-A8 00 Fast Read Dual I/O BBh A31-A24 A23-A16 A15-A8 A7-A0 Dummy(11) (D7-D0) Fast Read Dual I/O with 4-Byte Address BCh A31-A24 A23-A16 A15-A8 A7-A0 Dummy(11) (D7-D0) 8 8 8 8 8 4 4 Number of Clock(1-1-4) Dummy (9) 4 (3).. Quad Input Page Program 32h A31-A24 A23-A16 A15-A8 A7-A0 (D7-D0) (D7-D0) Quad Page Program with 4-Byte Address 34h A31-A24 A23-A16 A15-A8 A7-A0 D7-D0 D7-D0 D7-D0 D7-D0 (9) Fast Read Quad Output 6Bh A31-A24 A23-A16 A15-A8 A7-A0 Dummy Dummy (D7-D0) Fast Read Quad Output with 4-Byte Address 6Ch A31-A24 A23-A16 A15-A8 A7-A0 Dummy Dummy (D7-D0)(9) Number of Clock(1-4-4) Byte9 8 2 2 2 2 2 4 2 2 Mftr./Device ID Quad I/O 94h A31-A24 A23-A16 A15-A8 00 Dummy(11) Dummy (MF7-MF0) (ID7-ID0) Fast Read Quad I/O EBh A31-A24 A23-A16 A15-A8 A7-A0 Dummy(11) Dummy (D7-D0) Fast Read Quad I/O with 4-Byte Address ECh A31-A24 A23-A16 A15-A8 A7-A0 Dummy(11) Dummy (D7-D0) Set Burst with Wrap 77h Dummy Dummy Dummy Dummy W7-W0 - 28 - Publication Release Date: October 23, 2018 Revision I W25Q256JV Notes: Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis "( )" indicate data output from the device on either 1, 2 or 4 IO pins. 2. The Status Register contents and Device ID will repeat continuously until /CS terminates the instruction. 3. At least one byte of data input is required for Page Program, Quad Page Program and Program Security Registers, up to 256 bytes of data input. If more than 256 bytes of data are sent to the device, the addressing will wrap to the beginning of the page and overwrite previously sent data. 4. Write Status Register-1 (01h) can also be used to program Status Register-1&2, see section 8.2.5. 5. Security Register Address: Security Register 1: A23-16 = 00h; A15-8 = 10h; A7-0 = byte address Security Register 2: A23-16 = 00h; A15-8 = 20h; A7-0 = byte address Security Register 3: A23-16 = 00h; A15-8 = 30h; A7-0 = byte address 6. Dual SPI address input format: IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0 IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1 7. Dual SPI data output format: IO0 = (D6, D4, D2, D0) IO1 = (D7, D5, D3, D1) 8. Quad SPI address input format: Set Burst with Wrap input format: IO0 = A20, A16, A12, A8, A4, A0, M4, M0 IO0 = x, x, x, x, x, x, W4, x IO1 = A21, A17, A13, A9, A5, A1, M5, M1 IO1 = x, x, x, x, x, x, W5, x IO2 = A22, A18, A14, A10, A6, A2, M6, M2 IO2 = x, x, x, x, x, x, W6, x IO3 = A23, A19, A15, A11, A7, A3, M7, M3 IO3 = x, x, x, x, x, x, x, x 9. Quad SPI data input/output format: IO0 = (D4, D0, .....) IO1 = (D5, D1, .....) IO2 = (D6, D2, .....) IO3 = (D7, D3, .....) 10. Fast Read Quad I/O data output format: IO0 = (x, x, x, x, D4, D0, D4, D0) IO1 = (x, x, x, x, D5, D1, D5, D1) IO2 = (x, x, x, x, D6, D2, D6, D2) IO3 = (x, x, x, x, D7, D3, D7, D3) 11. The first dummy is M7-M0 should be set to Fxh 1. - 29 - W25Q256JV 8.2 8.2.1 Instruction Descriptions Write Enable (06h) The Write Enable instruction (Figure 5) sets the Write Enable Latch (WEL) bit in the Status Register to a 1. The WEL bit must be set prior to every Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register and Erase/Program Security Registers instruction. The Write Enable instruction is entered by driving /CS low, shifting the instruction code "06h" into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (06h) DI (IO0) High Impedance DO (IO1) Figure 5. Write Enable Instruction 8.2.2 Write Enable for Volatile Status Register (50h) The non-volatile Status Register bits described in section 7.1 can also be written to as volatile bits. This gives more flexibility to change the system configuration and memory protection schemes quickly without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status Register nonvolatile bits. To write the volatile values into the Status Register bits, the Write Enable for Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h) instruction. Write Enable for Volatile Status Register instruction (Figure 6) will not set the Write Enable Latch (WEL) bit, it is only valid for the Write Status Register instruction to change the volatile Status Register bit values. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (50h) DI (IO0) DO (IO1) High Impedance Figure 6. Write Enable for Volatile Status Register Instruction - 30 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.3 Write Disable (04h) The Write Disable instruction (Figure 7) resets the Write Enable Latch (WEL) bit in the Status Register to a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code "04h" into the DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon completion of the Write Status Register, Erase/Program Security Registers, Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase and Reset instructions. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (04h) DI (IO0) High Impedance DO (IO1) Figure 7. Write Disable Instruction for SPI Mode 8.2.4 Read Status Register-1 (05h), Status Register-2 (35h) & Status Register-3 (15h) The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is entered by driving /CS low and shifting the instruction code "05h" for Status Register-1, "35h" for Status Register-2 or "15h" for Status Register-3 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 8. Refer to section 7.1 for Status Register descriptions. The Read Status Register instruction may be used at any time, even while a Program, Erase or Write Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the cycle is complete and if the device can accept another instruction. The Status Register can be read continuously, as shown in Figure 8. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (05h/35h/15h) DI (IO0) High Impedance DO (IO1) * = MSB Status Register-1/2/3 out 7 6 5 4 3 2 1 Status Register-1/2/3 out 0 * 7 * Figure 8. Read Status Register Instruction - 31 - 6 5 4 3 2 1 0 7 W25Q256JV 8.2.5 Write Status Register-1 (01h), Status Register-2 (31h) & Status Register-3 (11h) The Write Status Register instruction allows the Status Registers to be written. The writable Status Register bits include: TB, BP[3:0] in Status Register-1; CMP, LB[3:1], QE, SRL in Status Register-2;, DRV1, DRV0, WPS & ADP in Status Register-3. All other Status Register bit locations are read-only and will not be affected by the Write Status Register instruction. LB[3:1] are non-volatile OTP bits, once it is set to 1, it cannot be cleared to 0. To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have been executed for the device to accept the Write Status Register instruction (Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction code "01h/31h/11h", and then writing the status register data byte as illustrated in Figure 9a. To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0). However, SRL and LB[3:1] cannot be changed from "1" to "0" because of the OTP protection for these bits. Upon power off or the execution of a Software/Hardware Reset, the volatile Status Register bit values will be lost, and the non-volatile Status Register bit values will be restored. During non-volatile Status Register write operation (06h combined with 01h/31h/11h), after /CS is driven high, the self-timed Write Status Register cycle will commence for a time duration of t W (See AC Characteristics). While the Write Status Register cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a 0 when the cycle is finished and ready to accept other instructions again. After the Write Status Register cycle has finished, the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0. During volatile Status Register write operation (50h combined with 01h/31h/11h), after /CS is driven high, the Status Register bits will be refreshed to the new values within the time period of t SHSL2 (See AC Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period. Refer to section 7.1 for Status Register descriptions. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Mode 3 Mode 0 Instruction (01h/31h/11h) Register-1/2/3 in DI (IO0) 7 6 5 4 3 2 1 0 * High Impedance DO (IO1) * = MSB Figure 9a. Write Status Register-1/2/3 Instruction - 32 - Publication Release Date: October 23, 2018 Revision I W25Q256JV The W25Q256JV is also backward compatible to Winbond's previous generations of serial flash memories, in which the Status Register-1&2 can be written using a single "Write Status Register-1 (01h)" command. To complete the Write Status Register-1&2 instruction, the /CS pin must be driven high after the sixteenth bit of data that is clocked in as shown in Figure 9b. If /CS is driven high after the eighth clock, the Write Status Register-1 (01h) instruction will only program the Status Register-1, the Status Register-2 will not be affected (Previous generations will clear CMP and QE bits). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Mode 0 Instruction (01h) DI (IO0) Status Register 1 in 7 6 5 4 3 * 2 Status Register 2 in 1 0 15 * High Impedance DO (IO1) Mode 3 * = MSB Figure 9b. Write Status Register-1/2 Instruction - 33 - 14 13 12 11 10 9 8 W25Q256JV 8.2.6 Read Extended Address Register (C8h) When the device is in the 3-Byte Address Mode, the Extended Address Register is used as the 4th address byte A[31:24] to access memory regions beyond 128Mb. The Read Extended Address Register instruction is entered by driving /CS low and shifting the instruction code "C8h" into the DI pin on the rising edge of CLK. The Extended Address Register bits are then shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 10. When the device is in the 4-Byte Address Mode, the Extended Address Register is not used. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (C8h) DI (IO0) High Impedance DO (IO1) * = MSB Extended Addr. Reg. Out 7 6 5 4 * 3 2 Extended Addr. Reg. Out 1 0 7 6 5 4 3 2 1 0 7 * Figure 10a. Read Extended Address Register Instruction - 34 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.7 Write Extended Address Register (C5h) The Extended Address Register is a volatile register that stores the 4th byte address (A31-A24) when the device is operating in the 3-Byte Address Mode (ADS=0). To write the Extended Address Register bits, a Write Enable (06h) instruction must previously have been executed for the device to accept the Write Extended Address Register instruction (Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction code "C5h", and then writing the Extended Address Register data byte as illustrated in Figure 11. Upon power up or the execution of a Software/Hardware Reset, the Extended Address Register bit values will be cleared to 0. The Extended Address Register is only effective when the device is in the 3-Byte Address Mode. When the device operates in the 4-Byte Address Mode (ADS=1), any command with address input of A31-A24 will replace the Extended Address Register values. It is recommended to check and update the Extended Address Register if necessary when the device is switched from 4-Byte to 3-Byte Address Mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Mode 0 Instruction (C5h) Ext. Add. Reg in DI (IO0) 7 6 5 4 3 * High Impedance DO (IO1) Mode 3 * = MSB Figure 11. Write Extended Address Register Instruction - 35 - 2 1 0 W25Q256JV 8.2.8 Enter 4-Byte Address Mode (B7h) The Enter 4-Byte Address Mode instruction (Figure 12) will allow 32-bit address (A31-A0) to be used to access the memory array beyond 128Mb. The Enter 4-Byte Address Mode instruction is entered by driving /CS low, shifting the instruction code "B7h" into the DI pin and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (B7h) DI (IO0) High Impedance DO (IO1) Figure 12. Enter 4-Byte Address Mode instruction 8.2.9 Exit 4-Byte Address Mode (E9h) In order to be backward compatible, the Exit 4-Byte Address Mode instruction (Figure 13) will only allow 24-bit address (A23-A0) to be used to access the memory array up to 128Mb. The Extended Address Register must be used to access the memory array beyond 128Mb. The Exit 4-Byte Address Mode instruction is entered by driving /CS low, shifting the instruction code "E9h" into the DI pin and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 Mode 0 7 Mode 3 Mode 0 Instruction (E9h) DI (IO0) DO (IO1) High Impedance Figure 13. Exit 4-Byte Address Mode instruction - 36 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.10 Read Data (03h) The Read Data instruction allows one or more data bytes to be sequentially read from the memory. The instruction is initiated by driving the /CS pin low and then shifting the instruction code "03h" followed by a 32/24-bit address (A31/A23-A0) into the DI pin. The code and address bits are latched on the rising edge of the CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The address is automatically incremented to the next higher address after each byte of data is shifted out allowing for a continuous stream of data. This means that the entire memory can be accessed with a single instruction as long as the clock continues. The instruction is completed by driving /CS high. The Read Data instruction sequence is shown in Figure 14. If a Read Data instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of f R (see AC Electrical Characteristics). The Read Data (03h) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 Instruction (03h) 24-Bit Address DI (IO0) 23 22 21 3 2 1 0 * Data Out 1 High Impedance DO (IO1) 7 6 5 4 * * = MSB Figure 14. Read Data Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 37 - 3 2 1 0 7 W25Q256JV 8.2.11 Read Data with 4-Byte Address (13h) The Read Data with 4-Byte Address instruction is similar to the Read Data (03h) instruction. Instead of 24bit address, 32-bit address is needed following the instruction code 13h. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Read Data with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Read Data with 4-Byte Address instruction sequence is shown in Figure 15. If this instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Data with 4-Byte Address instruction allows clock rates from D.C. to a maximum of fR (see AC Electrical Characteristics). The Read Data with 4-Byte Address (13h) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 40 41 42 43 44 45 46 47 Mode 0 Instruction (13h) DI (IO0) 32-Bit Address 31 30 29 3 2 1 0 * Data Out 1 High Impedance DO (IO1) 7 6 5 4 3 2 1 0 7 * * = MSB Figure 15. Read Data with 4-Byte Address Instruction - 38 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.12 Fast Read (0Bh) The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24/32-bit address as shown in Figure 16. The dummy clocks allow the devices internal circuits additional time for setting up the initial address. During the dummy clocks the data value on the DO pin is a "don't care". /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (0Bh) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK Dummy Clocks DI (IO0) DO (IO1) 0 High Impedance Data Out 1 7 6 5 4 3 Data Out 2 2 1 * 0 7 6 5 4 * Figure 16. Fast Read Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 39 - 3 2 1 0 7 W25Q256JV 8.2.13 Fast Read with 4-Byte Address (0Ch) The Fast Read with 4-Byte Address instruction is similar to the Fast Read instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Read Data with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Fast Read with 4-Byte Address (0Ch) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 Mode 0 Instruction (0Ch) 32-Bit Address DI (IO0) 31 30 29 50 51 3 2 1 0 53 54 55 56 * High Impedance DO (IO1) * = MSB /CS 39 40 41 42 43 44 45 46 47 48 49 52 57 58 59 60 61 62 63 CLK Dummy Clocks DI (IO0) DO (IO1) 0 High Impedance Data Out 1 7 6 5 4 * 3 Data Out 2 2 1 0 7 6 5 4 3 2 1 0 7 * Figure 18. Fast Read with 4-Byte Address Instruction - 40 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.14 Fast Read Dual Output (3Bh) The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except that data is output on two pins; IO0 and IO1. This allows data to be transferred at twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for quickly downloading code from Flash to RAM upon power-up or for applications that cache code-segments to RAM for execution. Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24/32-bit address as shown in Figure 19. The dummy clocks allow the device's internal circuits additional time for setting up the initial address. The input data during the dummy clocks is "don't care". However, the IO0 pin should be high-impedance prior to the falling edge of the first data out clock. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (3Bh) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK IO0 switches from Input to Output Dummy Clocks DI (IO0) DO (IO1) 0 6 High Impedance 7 * 4 2 0 6 5 3 1 7 Data Out 1 * 4 2 0 6 5 3 1 7 Data Out 2 * 4 2 0 6 5 3 1 7 Data Out 3 Figure 19. Fast Read Dual Output Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 41 - * 4 2 0 6 5 3 1 7 Data Out 4 W25Q256JV 8.2.15 Fast Read Dual Output with 4-Byte Address (3Ch) The Fast Read Dual Output with 4-Byte Address instruction is similar to the Fast Read Dual Output instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Fast Read Dual Output with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Fast Read Dual Output with 4-Byte Address (3Ch) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 Mode 0 Instruction (3Ch) 32-Bit Address DI (IO0) 31 30 29 50 51 3 2 1 0 53 54 55 56 * High Impedance DO (IO1) * = MSB /CS 39 40 41 42 43 44 45 46 47 48 49 52 57 58 59 60 61 62 63 CLK IO0 switches from Input to Output Dummy Clocks DI (IO0) DO (IO1) 0 High Impedance 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 * Data Out 1 * Data Out 2 * Data Out 3 * Data Out 4 Figure 20. Fast Read Dual Output with 4-Byte Address Instruction - 42 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.16 Fast Read Quad Output (6Bh) The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction except that data is output on four pins, IO0, IO1, IO2, and IO3. The Quad Enable (QE) bit in Status Register-2 must be set to 1 before the device will accept the Fast Read Quad Output Instruction. The Fast Read Quad Output Instruction allows data to be transferred at four times the rate of standard SPI devices. The Fast Read Quad Output instruction can operate at the highest possible frequency of F R (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24/32-bit address as shown in Figure 21. The dummy clocks allow the device's internal circuits additional time for setting up the initial address. The input data during the dummy clocks is "don't care". However, the IO pins should be high-impedance prior to the falling edge of the first data out clock. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (6Bh) 24-Bit Address IO0 23 High Impedance IO1 22 21 42 43 3 2 1 45 46 47 0 * High Impedance IO2 High Impedance IO3 * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 CLK IO0 switches from Input to Output Dummy Clocks IO0 IO1 IO2 IO3 0 High Impedance High Impedance High Impedance 4 0 4 0 4 0 4 0 4 5 1 5 1 5 1 5 1 5 6 2 6 2 6 2 6 2 6 7 3 7 3 7 3 7 3 7 Byte 1 Byte 2 Byte 3 Byte 4 Figure 21. Fast Read Quad Output Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 43 - W25Q256JV 8.2.17 Fast Read Quad Output with 4-Byte Address (6Ch) The Fast Read Quad Output with 4-Byte Address instruction is similar to the Fast Read Quad Output instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Fast Read Quad Output with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Fast Read Quad Output with 4-Byte Address (6Ch) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 Mode 0 Instruction (6Ch) 32-Bit Address IO0 31 High Impedance IO1 30 29 50 51 3 2 1 53 54 55 0 * High Impedance IO2 High Impedance IO3 * = MSB /CS 39 40 41 42 43 44 45 46 47 48 49 52 CLK IO0 switches from Input to Output Dummy Clocks IO0 IO1 IO2 IO3 0 High Impedance High Impedance High Impedance 4 0 4 0 4 0 4 0 4 5 1 5 1 5 1 5 1 5 6 2 6 2 6 2 6 2 6 7 3 7 3 7 3 7 3 7 Byte 1 Byte 2 Byte 3 Byte 4 Figure 22. Fast Read Quad Output with 4-Byte Address Instruction - 44 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.18 Fast Read Dual I/O (BBh) The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to input the Address bits (A23/A31-0) two bits per clock. This reduced instruction overhead may allow for code execution (XIP) directly from the Dual SPI in some applications. Similar to the Fast Read Dual Output (3Bh) instruction, the Fast Read Dual I/O instruction can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding four "dummy" clocks after the 24/32-bit address as shown in Figure 23. The dummy clocks allow the device's internal circuits additional time for setting up the initial address. The input data during the dummy clocks is "don't care". However, the IO0 pin should be high-impedance prior to the falling edge of the first data out clock. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (BBh) A23-16 A15-8 A7-0 M7-0 DI (IO0) 22 20 18 16 14 12 10 8 6 4 2 0 6 4 2 0 DO (IO1) 23 21 19 17 15 13 11 9 7 5 3 1 7 5 3 1 * * = MSB * /CS 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 CLK IOs switch from Input to Output DI (IO0) 0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 DO (IO1) 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 * Byte 1 * Byte 2 * Byte 3 * Byte 4 Figure 23a. Fast Read Dual I/O (M7-M0 should be set to Fxh) 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 45 - W25Q256JV 8.2.19 Fast Read Dual I/O with 4-Byte Address (BCh) The Fast Read Dual I/O with 4-Byte Address instruction is similar to the Fast Read Dual I/O instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Fast Read Dual I/O with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Fast Read Dual I/O with 4-Byte Address (BCh) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 21 22 23 24 25 26 27 Mode 0 Instruction (BCh) 32-Bit Address M7-0 DI (IO0) 30 28 26 4 2 0 6 4 2 0 DO (IO1) 31 29 27 5 3 1 7 5 3 1 * * = MSB * /CS 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 CLK IOs switch from Input to Output DI (IO0) 0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 DO (IO1) 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 * Byte 1 * Byte 2 * Byte 3 * Byte 4 Figure 25a. Fast Read Dual I/O w/ 4-Byte Addr. (M7-M0 shuld set to Fxh, SPI Mode only) - 46 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.20 Fast Read Quad I/O (EBh) The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except that address and data bits are input and output through four pins IO 0, IO1, IO2 and IO3 and four Dummy clocks are required in SPI mode prior to the data output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to enable the Fast Read Quad I/O Instruction. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (EBh) A23-16 A15-8 A7-0 M7-0 Dummy IOs switch from Input to Output Dummy IO0 20 16 12 8 4 0 4 0 4 0 4 0 4 IO1 21 17 13 9 5 1 5 1 5 1 5 1 5 IO2 22 18 14 10 6 2 6 2 6 2 6 2 6 IO3 23 19 15 11 7 3 7 3 7 3 7 3 7 Byte 1 Byte 2 Byte 3 Figure 26a. Fast Read Quad I/O (M7-M0 should be set to Fxh) 32-Bit Address is required when the device is operating in 4-Byte Address Mode Fast Read Quad I/O with "8/16/32/64-Byte Wrap Around" in Standard SPI mode The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a "Set Burst with Wrap" (77h) command prior to EBh. The "Set Burst with Wrap" (77h) command can either enable or disable the "Wrap Around" feature for the following EBh commands. When "Wrap Around" is enabled, the data being accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte page. The output data starts at the initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until /CS is pulled high to terminate the command. The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read commands. The "Set Burst with Wrap" instruction allows three "Wrap Bits", W6-4 to be set. The W4 bit is used to enable or disable the "Wrap Around" operation while W6-5 are used to specify the length of the wrap around section within a page. Refer to section 8.2.24 for detail descriptions. - 47 - W25Q256JV 8.2.21 Fast Read Quad I/O with 4-Byte Address (ECh) The Fast Read Quad I/O with 4-Byte Address instruction is similar to the Fast Read Dual I/O instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Fast Read Quad I/O with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. The Fast Read Quad I/O with 4-Byte Address (ECh) instruction is only supported in Standard SPI mode. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 14 15 16 17 18 19 20 21 22 23 24 25 Mode 0 Instruction (ECh) 32-Bit Address M7-0 Dummy IOs switch from Input to Output Dummy IO0 28 24 4 0 4 0 4 0 4 0 4 IO1 29 25 5 1 5 1 5 1 5 1 5 IO2 30 26 6 2 6 2 6 2 6 2 6 IO3 31 27 7 3 7 3 7 3 7 3 7 Byte 1 Byte 2 Byte 3 Figure 28. Fast Read Quad I/O w/ 4-Byte Addr. (M7-M0 should be set to Fxh) Fast Read Quad I/O with "8/16/32/64-Byte Wrap Around" in Standard SPI mode The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a "Set Burst with Wrap" (77h) command prior to ECh. The "Set Burst with Wrap" (77h) command can either enable or disable the "Wrap Around" feature for the following ECh commands. When "Wrap Around" is enabled, the data being accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte page. The output data starts at the initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until /CS is pulled high to terminate the command. The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read commands. The "Set Burst with Wrap" instruction allows three "Wrap Bits", W6-4 to be set. The W4 bit is used to enable or disable the "Wrap Around" operation while W6-5 are used to specify the length of the wrap around section within a page. Refer to section 8.2.24 for detail descriptions. - 48 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.22 Set Burst with Wrap (77h) The Set Burst with Wrap (77h) instruction is used in conjunction with "Fast Read Quad I/O" and "Word Read Quad I/O" instructions to access a fixed length of 8/16/32/64-byte section within a 256-byte page. Certain applications can benefit from this feature and improve the overall system code execution performance. Similar to a Quad I/O instruction, the Set Burst with Wrap instruction is initiated by driving the /CS pin low and then shifting the instruction code "77h" followed by 24/32 dummy bits and 8 "Wrap Bits", W7-0. The instruction sequence is shown in Figure 28. Wrap bit W7 and the lower nibble W3-0 are not used. W4 = 0 W6, W5 0 0 1 1 W4 =1 (DEFAULT) Wrap Around Wrap Length Wrap Around Wrap Length Yes Yes Yes Yes 8-byte 16-byte 32-byte 64-byte No No No No N/A N/A N/A N/A 0 1 0 1 Once W6-4 is set by a Set Burst with Wrap instruction, all the following "Fast Read Quad I/O" instructions will use the W6-4 setting to access the 8/16/32/64-byte section within any page. To exit the "Wrap Around" function and return to normal read operation, another Set Burst with Wrap instruction should be issued to set W4 = 1. The default value of W4 upon power on or after a software/hardware reset is 1. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Mode 3 Mode 0 don't care Instruction (77h) don't care don't care Wrap Bit IO0 X X X X X X w4 X IO1 X X X X X X w5 X IO2 X X X X X X w6 X IO3 X X X X X X X X Figure 28. Set Burst with Wrap Instruction 32-Bit dummy bits are required when the device is operating in 4-Byte Address Mode - 49 - W25Q256JV 8.2.23 Page Program (02h) The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device will accept the Page Program Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "02h" followed by a 24/32-bit address (A23/A31A0) and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. The Page Program instruction sequence is shown in Figure 32. If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceeds the remaining page length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a partial page) can be programmed without having any effect on other bytes within the same page. One condition to perform a partial page program is that the number of clocks cannot exceed the remaining page length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the page and overwrite previously sent data. As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS is driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See AC Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Page Program instruction will not be executed if the addressed page is protected by the Block Protect (CMP, TB, BP3, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks. /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 1 0 * 6 5 4 3 2 1 0 2079 Data Byte 1 2 2078 3 2077 21 2076 22 2075 24-Bit Address 23 2074 Instruction (02h) DI (IO0) 2073 CLK 7 * * = MSB 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 2072 /CS 55 CLK Mode 0 Data Byte 2 DI (IO0) Mode 3 0 7 * 6 5 4 3 Data Byte 3 2 1 0 7 6 5 4 3 Data Byte 256 2 1 0 7 * 6 5 4 3 2 1 0 * Figure 32. Page Program Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 50 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.24 Page Program with 4-Byte Address (12h) The Page Program with 4-Byte Address instruction is similar to the Page Program instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Page Program with 4-Byte Address instruction will always require 32bit address to access the entire 256Mb memory. /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 40 41 42 43 44 45 46 47 Mode 0 1 * 0 6 5 4 3 2 1 0 2087 Data Byte 1 2 2086 3 2085 29 2084 30 2083 32-Bit Address 31 2082 Instruction (12h) DI (IO0) 2081 CLK 7 * * = MSB 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 2080 /CS CLK Mode 0 Data Byte 2 DI (IO0) Mode 3 0 7 * 6 5 4 3 Data Byte 3 2 1 0 7 6 5 4 3 * Data Byte 256 2 1 0 7 * Figure 33. Page Program with 4-Byte Addr. - 51 - 6 5 4 3 2 1 0 W25Q256JV 8.2.25 Quad Input Page Program (32h) The Quad Page Program instruction allows up to 256 bytes of data to be programmed at previously erased (FFh) memory locations using four pins: IO0, IO1, IO2, and IO3. The Quad Page Program can improve performance for PROM Programmer and applications that have slow clock speeds <5MHz. Systems with faster clock speed will not realize much benefit for the Quad Page Program instruction since the inherent page program time is much greater than the time it take to clock-in the data. To use Quad Page Program the Quad Enable (QE) bit in Status Register-2 must be set to 1. A Write Enable instruction must be executed before the device will accept the Quad Page Program instruction (Status Register-1, WEL=1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "32h" followed by a 24/32-bit address (A23/A31-A0) and at least one data byte, into the IO pins. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. All other functions of Quad Page Program are identical to standard Page Program. The Quad Page Program instruction sequence is shown in Figure 34. /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 22 21 3 2 1 543 23 542 IO0 539 24-Bit Address 538 Instruction (32h) 541 CLK 0 * IO1 IO2 IO3 * = MSB 33 34 35 36 37 540 32 537 31 536 /CS CLK Mode 0 Byte 253 Byte 254 Byte 255 Byte 256 Byte 1 Byte 2 Byte 3 4 0 4 0 4 0 4 0 4 0 4 0 4 0 IO1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 IO2 6 2 6 2 6 2 6 2 6 2 6 2 6 2 IO3 7 3 7 3 7 3 7 3 7 3 7 3 7 3 IO0 Mode 3 0 * * * * * * * Figure 34. Quad Input Page Program Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 52 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.26 Quad Input Page Program with 4-Byte Address (34h) The Quad Input Page Program with 4-Byte Address instruction is similar to the Quad Input Page Program instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Quad Input Page Program with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 36 37 38 39 Mode 0 30 29 3 2 1 551 31 550 IO0 547 32-Bit Address 546 Instruction (34h) 549 CLK 0 * IO1 IO2 IO3 * = MSB 41 42 43 44 45 548 40 545 39 544 /CS CLK Mode 0 Byte 253 Byte 254 Byte 255 Byte 256 Byte 1 Byte 2 Byte 3 4 0 4 0 4 0 4 0 4 0 4 0 4 0 IO1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 IO2 6 2 6 2 6 2 6 2 6 2 6 2 6 2 IO3 7 3 7 3 7 3 7 3 7 3 7 3 7 3 IO0 Mode 3 0 * * * * * * Figure 35. Quad Input Page Program with 4-Byte Addr. - 53 - * W25Q256JV 8.2.27 Sector Erase (20h) The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "20h" followed a 24/32-bit sector address (A23/A31-A0). The Sector Erase instruction sequence is shown in Figure 36. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Sector Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, TB, BP3, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (20h) 24-Bit Address DI (IO0) DO (IO1) 9 Mode 0 23 22 2 1 0 * High Impedance * = MSB Figure 36. Sector Erase Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 54 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.28 Sector Erase with 4-Byte Address (21h) The Sector Erase with 4-Byte Address instruction is similar to the Sector Erase instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the Sector Erase with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 37 39 Mode 3 Mode 0 Instruction (21h) 32-Bit Address DI (IO0) 31 30 2 * DO (IO1) 38 Mode 0 High Impedance * = MSB Figure 37. Sector Erase with 4-Byte Address Instruction - 55 - 1 0 W25Q256JV 8.2.29 32KB Block Erase (52h) The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "52h" followed a 24/32-bit block address (A23/A31-A0). The Block Erase instruction sequence is shown in Figure 38. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, TB, BP3, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (52h) 24-Bit Address DI (IO0) DO (IO1) 9 Mode 0 23 22 2 1 0 * High Impedance * = MSB Figure 38a. 32KB Block Erase Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 56 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.30 64KB Block Erase (D8h) The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "D8h" followed a 24/32-bit block address (A23/A31-A0). The Block Erase instruction sequence is shown in Figure 33a & 33b. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, TB, BP3, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (D8h) 24-Bit Address DI (IO0) DO (IO1) 9 Mode 0 23 22 2 1 0 * High Impedance * = MSB Figure 39. 64KB Block Erase Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 57 - W25Q256JV 8.2.31 64KB Block Erase with 4-Byte Address (DCh) The 64KB Block Erase with 4-Byte Address instruction is similar to the 64KB Block Erase instruction except that it requires 32-bit address instead of 24-bit address. No matter the device is operating in 3-Byte Address Mode or 4-byte Address Mode, the 64KB Block Erase with 4-Byte Address instruction will always require 32-bit address to access the entire 256Mb memory. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 37 38 39 Mode 0 Mode 3 Mode 0 Instruction (DCh) 32-Bit Address DI (IO0) 31 30 2 1 0 * DO (IO1) High Impedance * = MSB Figure 40. 64KB Block Erase with 4-Byte Address Instruction - 58 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.32 Chip Erase (C7h / 60h) The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "C7h" or "60h". The Chip Erase instruction sequence is shown in Figure 41. The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to accept other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed if any memory region is protected by the Block Protect (CMP, TB, BP3, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 0 Instruction (C7h/60h) DI (IO0) DO (IO1) Mode 3 High Impedance Figure 41. Chip Erase Instruction Sequence Diagram - 59 - W25Q256JV 8.2.33 Erase / Program Suspend (75h) The Erase/Program Suspend instruction "75h", allows the system to interrupt a Sector or Block Erase operation or a Page Program operation and then read from or program/erase data to, any other sectors or blocks. The Erase/Program Suspend instruction sequence is shown in Figure 42. The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h, 44h) are not allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If written during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status Register instruction (01h) and Program instructions (02h, 32h, 42h) are not allowed during Program Suspend. Program Suspend is valid only during the Page Program or Quad Page Program operation. The Erase/Program Suspend instruction "75h" will be accepted by the device only if the SUS bit in the Status Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase or a Page Program operation is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend instruction will be ignored by the device. A maximum of time of "t SUS" (See AC Characteristics) is required to suspend the erase or program operation. The BUSY bit in the Status Register will be cleared from 1 to 0 within "tSUS" and the SUS bit in the Status Register will be set from 0 to 1 immediately after Erase/Program Suspend. For a previously resumed Erase/Program operation, it is also required that the Suspend instruction "75h" is not issued earlier than a minimum of time of "t SUS" following the preceding Resume instruction "7Ah". Unexpected power off during the Erase/Program suspend state will reset the device and release the suspend state. SUS bit in the Status Register will also reset to 0. The data within the page, sector or block that was being suspended may become corrupted. It is recommended for the user to implement system design techniques against the accidental power interruption and preserve data integrity during erase/program suspend state. /CS tSUS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (75h) DI (IO0) DO (IO1) High Impedance Accept instructions Figure 42. Erase/Program Suspend Instruction - 60 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.34 Erase / Program Resume (7Ah) The Erase/Program Resume instruction "7Ah" must be written to resume the Sector or Block Erase operation or the Page Program operation after an Erase/Program Suspend. The Resume instruction "7Ah" will be accepted by the device only if the SUS bit in the Status Register equals to 1 and the BUSY bit equals to 0. After issued the SUS bit will be cleared from 1 to 0 immediately, the BUSY bit will be set from 0 to 1 within 200ns and the Sector or Block will complete the erase operation or the page will complete the program operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction "7Ah" will be ignored by the device. The Erase/Program Resume instruction sequence is shown in Figure 43. Resume instruction is ignored if the previous Erase/Program Suspend operation was interrupted by unexpected power off. It is also required that a subsequent Erase/Program Suspend instruction not to be issued within a minimum of time of "tSUS" following a previous Resume instruction. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (7Ah) DI (IO0) Resume previously suspended Program or Erase Figure 43. Erase/Program Resume Instruction - 61 - W25Q256JV 8.2.35 Power-down (B9h) Although the standby current during normal operation is relatively low, standby current can be further reduced with the Power-down instruction. The lower power consumption makes the Power-down instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC Characteristics). The instruction is initiated by driving the /CS pin low and shifting the instruction code "B9h" as shown in Figure 44. The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down instruction will not be executed. After /CS is driven high, the power-down state will entered within the time duration of tDP (See AC Characteristics). While in the power-down state only the Release Power-down / Device ID (ABh) instruction, which restores the device to normal operation, will be recognized. All other instructions are ignored. This includes the Read Status Register instruction, which is always available during normal operation. Ignoring all but one instruction makes the Power Down state a useful condition for securing maximum write protection. The device always powers-up in the normal operation with the standby current of ICC1. /CS tDP Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (B9h) DI (IO0) Stand-by current Power-down current Figure 44. Deep Power-down Instruction - 62 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.36 Release Power-down / Device ID (ABh) The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to release the device from the power-down state, or obtain the devices electronic identification (ID) number. To release the device from the power-down state, the instruction is issued by driving the /CS pin low, shifting the instruction code "ABh" and driving /CS high as shown in Figure 45. Release from power-down will take the time duration of tRES1 (See AC Characteristics) before the device will resume normal operation and other instructions are accepted. The /CS pin must remain high during the t RES1 time duration. When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by driving the /CS pin low and shifting the instruction code "ABh" followed by 3-dummy bytes. The Device ID bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first. The Device ID values for the W25Q256JV is listed in Manufacturer and Device Identification table. The Device ID can be read continuously. The instruction is completed by driving /CS high. When used to release the device from the power-down state and obtain the Device ID, the instruction is the same as previously described, and shown in Figure 45, except that after /CS is driven high it must remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will resume normal operation and other instructions will be accepted. If the Release from Power-down / Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals 1) the instruction is ignored and will not have any effects on the current cycle. /CS tRES1 Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (ABh) DI (IO0) Power-down current Stand-by current Figure 45a. Release Power-down Instruction /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 29 30 31 32 33 34 35 36 37 38 Mode 3 Mode 0 Mode 0 Instruction (ABh) DI (IO0) tRES2 3 Dummy Bytes 23 22 2 1 0 * Device ID High Impedance DO (IO1) 7 6 5 4 3 2 1 0 * * = MSB Power-down current Figure 45b. Release Power-down / Device ID Instruction - 63 - Stand-by current W25Q256JV 8.2.37 Read Manufacturer / Device ID (90h) The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down / Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID. The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device ID instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "90h" followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 46. The Device ID values for the W25Q256JV are listed in Manufacturer and Device Identification table. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (90h) Address (000000h) DI (IO0) 23 22 21 42 43 3 2 45 46 1 0 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 Mode 3 CLK DI (IO0) Mode 0 0 DO (IO1) 7 Manufacturer ID (EFh) * 6 5 4 3 2 1 0 Device ID Figure 46. Read Manufacturer / Device ID Instruction - 64 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.38 Read Manufacturer / Device ID Dual I/O (92h) The Read Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer / Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x speed. The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "92h" followed by a 24/32-bit address (A23/A31-A0) of 000000h, but with the capability to input the Address bits two bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out 2 bits per clock on the falling edge of CLK with most significant bits (MSB) first as shown in Figure 47. The Device ID values for the W25Q256JV are listed in Manufacturer and Device Identification table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (92h) A23-16 DI (IO0) High Impedance DO (IO1) * = MSB A15-8 A7-0 (00h) M7-0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 * * * * /CS 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Mode 3 CLK Mode 0 IOs switch from Input to Output DI (IO0) 0 6 4 2 0 6 4 2 0 6 DO (IO1) 1 7 5 3 1 7 5 3 1 * MFR ID * Device ID 4 2 0 6 7 5 3 1 7 * MFR ID (repeat) * 4 2 0 5 3 1 Device ID (repeat) Figure 47. Read Manufacturer / Device ID Dual I/O Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode Note: The "Continuous Read Mode" bits M(7-0) must be set to Fxh to be compatible with Fast Read Dual I/O instruction. - 65 - W25Q256JV 8.2.39 Read Manufacturer / Device ID Quad I/O (94h) The Read Manufacturer / Device ID Quad I/O instruction is an alternative to the Read Manufacturer / Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 4x speed. The Read Manufacturer / Device ID Quad I/O instruction is similar to the Fast Read Quad I/O instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "94h" followed by a four clock dummy cycles and then a 24/32-bit address (A23/A31-A0) of 000000h, but with the capability to input the Address bits four bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out four bits per clock on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 48. The Device ID values for the W25Q256JV are listed in Manufacturer and Device Identification table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (94h) IO0 High Impedance IO1 High Impedance IO2 High Impedance IO3 A7-0 (00h) M7-0 Dummy IOs switch from Input to Output A23-16 A15-8 Dummy 4 0 4 0 4 0 4 0 4 0 4 0 5 1 5 1 5 1 5 1 5 1 5 1 6 2 6 2 6 2 6 2 6 2 6 2 7 3 7 3 7 3 7 3 7 3 7 3 MFR ID Device ID /CS 23 24 25 26 27 28 29 30 Mode 3 CLK Mode 0 IO0 0 4 0 4 0 4 0 4 0 IO1 1 5 1 5 1 5 1 5 1 IO2 2 6 2 6 2 6 2 6 2 IO3 3 7 3 7 3 7 3 7 3 MFR ID (repeat) Device ID (repeat) MFR ID (repeat) Device ID (repeat) Figure 48. Read Manufacturer / Device ID Quad I/O Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode Note: The "Continuous Read Mode" bits M(7-0) must be set to Fxh to be compatible with Fast Read Quad I/O instruction. - 66 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.40 Read Unique ID Number (4Bh) The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique to each W25Q256JV device. The ID number can be used in conjunction with user software methods to help prevent copying or cloning of a system. The Read Unique ID instruction is initiated by driving the /CS pin low and shifting the instruction code "4Bh" followed by a four bytes of dummy clocks. After which, the 64bit ID is shifted out on the falling edge of CLK as shown in Figure 49. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (4Bh) Dummy Byte 1 Dummy Byte 2 DI (IO0) High Impedance DO (IO1) 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 102 24 101 23 100 /CS Mode 3 CLK Mode 0 Dummy Byte 3 Dummy Byte 4 DI (IO0) DO (IO1) High Impedance * = MSB 63 62 61 2 * 64-bit Unique Serial Number Figure 49. Read Unique ID Number Instruction 5 Dummy Bytes are required when the device is operating in 4-Byte Address Mode - 67 - 1 0 W25Q256JV 8.2.41 Read JEDEC ID (9Fh) For compatibility reasons, the W25Q256JV provides several instructions to electronically determine the identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI compatible serial memories that was adopted in 2003. The instruction is initiated by driving the /CS pin low and shifting the instruction code "9Fh". The JEDEC assigned Manufacturer ID byte for Winbond (EFh) and two Device ID bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 50. For memory type and capacity values refer to Manufacturer and Device Identification table. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Instruction (9Fh) DI (IO0) Manufacturer ID (EFh) High Impedance DO (IO1) * = MSB /CS 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Mode 3 CLK Mode 0 DI (IO0) Memory Type ID15-8 DO (IO1) 7 * 6 5 4 3 2 Capacity ID7-0 1 0 7 6 5 4 3 2 1 0 * Figure 50. Read JEDEC ID Instruction - 68 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.42 Read SFDP Register (5Ah) The W25Q256JV features a 256-Byte Serial Flash Discoverable Parameter (SFDP) register that contains information about device configurations, available instructions and other features. The SFDP parameters are stored in one or more Parameter Identification (PID) tables. Currently only one PID table is specified, but more may be added in the future. The Read SFDP Register instruction is compatible with the SFDP standard initially established in 2010 for PC and other applications, as well as the JEDEC standard JESD216 that is published in 2011. Most Winbond SpiFlash Memories shipped after June 2011 (date code 1124 and beyond) support the SFDP feature as specified in the applicable datasheet. The Read SFDP instruction is initiated by driving the /CS pin low and shifting the instruction code "5Ah" followed by a 24-bit address (A23-A0)(1) into the DI pin. Eight "dummy" clocks are also required before the SFDP register contents are shifted out on the falling edge of the 40th CLK with most significant bit (MSB) first as shown in Figure 51. For SFDP register values and descriptions, please refer to the Winbond Application Note for SFDP Definition Table. Note: 1. A23-A8 = 0; A7-A0 are used to define the starting byte address for the 256-Byte SFDP Register. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (5Ah) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK Dummy Byte DI (IO0) 0 7 6 5 4 3 2 1 0 Data Out 1 DO (IO1) High Impedance * = MSB 7 6 5 4 * 3 Data Out 2 2 1 0 7 6 5 4 3 2 1 * Figure 51. Read SFDP Register Instruction Sequence Diagram Only 24-Bit Address is required when the device is operating in either 3-Byte or 4-Byte Address Mode - 69 - 0 7 W25Q256JV 8.2.43 Erase Security Registers (44h) The W25Q256JV offers three 256-byte Security Registers which can be erased and programmed individually. These registers may be used by the system manufacturers to store security and other important information separately from the main memory array. The Erase Security Register instruction is similar to the Sector Erase instruction. A Write Enable instruction must be executed before the device will accept the Erase Security Register Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "44h" followed by a 24/32-bit address (A23/A31-A0) to erase one of the three security registers. ADDRESS {A23/A31}-16 A15-12 A11-8 A7-0 Security Register #1 00h/0000h 0001 0000 Don't Care Security Register #2 00h/0000h 0010 0000 Don't Care Security Register #3 00h/0000h 0011 0000 Don't Care The Erase Security Register instruction sequence is shown in Figure 52. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the instruction will not be executed. After /CS is driven high, the self-timed Erase Security Register operation will commence for a time duration of tSE (See AC Characteristics). While the Erase Security Register cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Erase Security Register cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Security Register Lock Bits (LB3-1) in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1, the corresponding security register will be permanently locked, Erase Security Register instruction to that register will be ignored (Refer to section 7.1.8 for detail descriptions). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (44h) 24-Bit Address DI (IO0) DO (IO1) 9 Mode 0 23 22 2 1 0 * High Impedance * = MSB Figure 52. Erase Security Registers Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 70 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.44 Program Security Registers (42h) The Program Security Register instruction is similar to the Page Program instruction. It allows from one byte to 256 bytes of security register data to be programmed at previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device will accept the Program Security Register Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "42h" followed by a 24/32-bit address (A23/A31-A0) and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. ADDRESS {A23/A31}-16 A15-12 A11-8 A7-0 Security Register #1 00h/0000h 0001 0000 Byte Address Security Register #2 00h/0000h 0010 0000 Byte Address Security Register #3 00h/0000h 0011 0000 Byte Address The Program Security Register instruction sequence is shown in Figure 53. The Security Register Lock Bits (LB3-1) in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1, the corresponding security register will be permanently locked, Program Security Register instruction to that register will be ignored (See 7.1.8, 8.2.25 for detail descriptions). /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 2 1 * 0 6 5 4 3 2 1 0 2079 3 2078 21 2077 22 2076 23 Data Byte 1 2075 24-Bit Address 2074 Instruction (42h) DI (IO0) 2073 CLK 7 * * = MSB 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 2072 /CS CLK Mode 0 Data Byte 2 DI (IO0) Mode 3 0 7 * 6 5 4 3 Data Byte 3 2 1 0 7 6 5 4 3 * Data Byte 256 2 1 0 7 6 5 4 3 * Figure 53. Program Security Registers Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 71 - 2 1 0 W25Q256JV 8.2.45 Read Security Registers (48h) The Read Security Register instruction is similar to the Fast Read instruction and allows one or more data bytes to be sequentially read from one of the four security registers. The instruction is initiated by driving the /CS pin low and then shifting the instruction code "48h" followed by a 24/32-bit address (A23/A31-A0) and eight "dummy" clocks into the DI pin. The code and address bits are latched on the rising edge of the CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The byte address is automatically incremented to the next byte address after each byte of data is shifted out. Once the byte address reaches the last byte of the register (byte address FFh), it will reset to address 00h, the first byte of the register, and continue to increment. The instruction is completed by driving /CS high. The Read Security Register instruction sequence is shown in Figure 54. If a Read Security Register instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Security Register instruction allows clock rates from D.C. to a maximum of FR (see AC Electrical Characteristics). ADDRESS {A23/A31}-16 A15-12 A11-8 A7-0 Security Register #1 00h/0000h 0001 0000 Byte Address Security Register #2 00h/0000h 0010 0000 Byte Address Security Register #3 00h/0000h 0011 0000 Byte Address /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (48h) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK Dummy Byte DI (IO0) 0 7 6 5 4 3 2 1 0 Data Out 1 DO (IO1) High Impedance 7 6 5 4 * 3 Data Out 2 2 1 0 7 6 5 4 3 2 1 0 7 * Figure 54. Read Security Registers Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 72 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.46 Individual Block/Sector Lock (36h) The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be set to 1. If WPS=0, the write protection will be determined by the combination of CMP, TB, BP[3:0] bits in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device power up or after a Reset are 1, so the entire memory array is being protected. To lock a specific block or sector as illustrated in Figure 4d, an Individual Block/Sector Lock command must be issued by driving /CS low, shifting the instruction code "36h" into the Data Input (DI) pin on the rising edge of CLK, followed by a 24/32-bit address and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 29 30 31 Mode 0 Mode 0 Instruction (36h) 24-Bit Address DI (IO0) 23 22 2 1 0 * DO (IO1) Mode 3 High Impedance * = MSB Figure 55. Individual Block/Sector Lock Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 73 - W25Q256JV 8.2.47 Individual Block/Sector Unlock (39h) The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be set to 1. If WPS=0, the write protection will be determined by the combination of CMP, TB, BP[3:0] bits in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device power up or after a Reset are 1, so the entire memory array is being protected. To unlock a specific block or sector as illustrated in Figure 4d, an Individual Block/Sector Unlock command must be issued by driving /CS low, shifting the instruction code "39h" into the Data Input (DI) pin on the rising edge of CLK, followed by a 24/32-bit address and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 29 30 31 Mode 0 Mode 3 Mode 0 Instruction (39h) 24-Bit Address DI (IO0) 23 22 2 1 0 * DO (IO1) High Impedance * = MSB Figure 56. Individual Block Unlock Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 74 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.48 Read Block/Sector Lock (3Dh) The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be set to 1. If WPS=0, the write protection will be determined by the combination of CMP, TB, BP[3:0] bits in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device power up or after a Reset are 1, so the entire memory array is being protected. To read out the lock bit value of a specific block or sector as illustrated in Figure 4d, a Read Block/Sector Lock command must be issued by driving /CS low, shifting the instruction code "3Dh" into the Data Input (DI) pin on the rising edge of CLK, followed by a 24/32-bit address. The Block/Sector Lock bit value will be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 57. If the least significant bit (LSB) is 1, the corresponding block/sector is locked; if LSB=0, the corresponding block/sector is unlocked, Erase/Program operation can be performed. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 Mode 0 Instruction (3Dh) 24-Bit Address DI (IO0) 23 22 21 3 2 1 0 * Lock Value Out High Impedance DO (IO1) * Mode 3 X X X X X * = MSB Figure 57. Read Block Lock Instruction 32-Bit Address is required when the device is operating in 4-Byte Address Mode - 75 - X X 0 W25Q256JV 8.2.49 Global Block/Sector Lock (7Eh) All Block/Sector Lock bits can be set to 1 by the Global Block/Sector Lock instruction. The command must be issued by driving /CS low, shifting the instruction code "7Eh" into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (7Eh) DI (IO0) High Impedance DO (IO1) Figure 58. Global Block Lock Instruction for SPI 8.2.50 Global Block/Sector Unlock (98h) All Block/Sector Lock bits can be set to 0 by the Global Block/Sector Unlock instruction. The command must be issued by driving /CS low, shifting the instruction code "98h" into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 Mode 0 6 7 Mode 3 Mode 0 Instruction (98h) DI (IO0) DO (IO1) High Impedance Figure 59. Global Block Unlock Instruction - 76 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 8.2.51 Enable Reset (66h) and Reset Device (99h) Because of the small package and the limitation on the number of pins, the W25Q256JV provide a software Reset instruction instead of a dedicated RESET pin. Once the Reset instruction is accepted, any on-going internal operations will be terminated and the device will return to its default power-on state and lose all the current volatile settings, such as Volatile Status Register bits, Write Enable Latch (WEL) status, Program/Erase Suspend status, Read parameter setting (P7-P0), Continuous Read Mode bit setting (M7-M0) and Wrap Bit setting (W6-W4). "Enable Reset (66h)" and "Reset (99h)" instructions can be issued in SPI. To avoid accidental reset, both instructions must be issued in sequence. Any other commands other than "Reset (99h)" after the "Enable Reset (66h)" command will disable the "Reset Enable" state. A new sequence of "Enable Reset (66h)" and "Reset (99h)" is needed to reset the device. Once the Reset command is accepted by the device, the device will take approximately tRST=30us to reset. During this period, no command will be accepted. Data corruption may happen if there is an on-going or suspended internal Erase or Program operation when Reset command sequence is accepted by the device. It is recommended to check the BUSY bit and the SUS bit in Status Register before issuing the Reset command sequence. /CS Mode 3 CLK 0 1 2 3 4 Mode 0 5 6 7 Mode 3 0 1 2 4 Instruction (66h) Instruction (99h) High Impedance Figure 60. Enable Reset and Reset Instruction Sequence - 77 - 5 6 7 Mode 3 Mode 0 DI (IO0) DO (IO1) 3 Mode 0 W25Q256JV 9. ELECTRICAL CHARACTERISTICS 9.1 Absolute Maximum Ratings (1) PARAMETERS SYMBOL Supply Voltage CONDITIONS VCC RANGE UNIT -0.6 to +4.6 V Voltage Applied to Any Pin VIO Relative to Ground -0.6 to VCC+0.4 V Transient Voltage on any Pin VIOT <20nS Transient Relative to Ground -2.0 to VCC+2.0 V Storage Temperature TSTG -65 to +150 C (2) C Lead Temperature TLEAD Electrostatic Discharge Voltage VESD See Note Human Body Model(3) -2000 to +2000 V Notes: 1. This device has been designed and tested for the specified operation ranges. Proper operation outside of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability. Exposure beyond absolute maximum ratings may cause permanent damage. 2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU. 3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms). 9.2 Operating Ranges PARAMETER Supply Voltage(1) Ambient Temperature, Operating SYMBOL VCC TA SPEC CONDITIONS MIN MAX UNIT FR = 133MHz, fR = 50MHz 3.0 3.6 V FR = 104MHz, fR = 50MHz 2.7 3.0 V Industrial -40 +85 C Industrial Plus -40 +105 C Note: 1. VCC voltage during Read can operate across the min and max range but should not exceed 10% of the programming (erase/write) voltage. - 78 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.3 Power-up Power-down Timing and Requirements SPEC PARAMETER SYMBOL VCC (min) to /CS Low tVSL(1) 20 s Time Delay Before Write Instruction tPUW 5 ms Write Inhibit Threshold Voltage VWI MIN (1) 1.0 (1) UNIT MAX 2.0 V Note: 1. These parameters are characterized only. VCC VCC (max) Program, Erase and Write Instructions are ignored /CS must track VCC VCC (min) Reset State tVSL Read Instructions Allowed Device is fully Accessible VWI tPUW Time Figure 65a. Power-up Timing and Voltage Levels /CS must track VCC during VCC Ramp Up/Down VCC /CS Time Figure 65b. Power-up, Power-Down Requirement - 79 - W25Q256JV 9.4 DC Electrical Characteristics SPEC PARAMETER SYMBOL CONDITIONS Input Capacitance CIN(1) VIN = 0V 6 pF Output Capacitance Cout(1) VOUT = 0V 8 pF Input Leakage ILI 2 A I/O Leakage ILO 2 A Standby Current ICC1 /CS = VCC, VIN = GND or VCC 10 60 A Power-down Current ICC2 /CS = VCC, VIN = GND or VCC 1 20 A Current Read Data / Dual /Quad 50MHz(2) ICC3 C = 0.1 VCC / 0.9 VCC DO = Open 8 15 mA Current Read Data / Dual Output Read/Quad Output Read 104MHz(2) ICC3 C = 0.1 VCC / 0.9 VCC DO = Open 12 20 mA Current Write Status Register ICC4 /CS = VCC 20 25 mA Current Page Program ICC5 /CS = VCC 20 25 mA Current Sector/Block Erase ICC6 /CS = VCC 20 25 mA Current Chip Erase ICC7 /CS = VCC 25 mA Input Low Voltage VIL -0.5 VCC x 0.3 V Input High Voltage VIH VCC x 0.7 VCC + 0.4 V Output Low Voltage VOL IOL = 100 A 0.2 V Output High Voltage VOH IOH = -100 A MIN TYP MAX 20 VCC - 0.2 UNIT V Notes: 1. Tested on sample basis and specified through design and characterization data. TA = 25 C, VCC = 3.0V. 2. Checker Board Pattern. - 80 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.5 AC Measurement Conditions PARAMETER SPEC SYMBOL Load Capacitance Input Rise and Fall Times Input Pulse Voltages Input Timing Reference Voltages Output Timing Reference Voltages MIN MAX UNIT CL 30 pF TR, TF 5 ns VIN 0.1 VCC to 0.9 VCC V IN 0.3 VCC to 0.7 VCC V OUT 0.5 VCC to 0.5 VCC V Note: 1. Output Hi-Z is defined as the point where data out is no longer driven. Input and Output Timing Reference Levels Input Levels 0.9 VCC 0.5 VCC 0.1 VCC Figure 66. AC Measurement I/O Waveform - 81 - W25Q256JV 9.6 AC Electrical Characteristics(6) SPEC DESCRIPTION SYMBOL ALT UNIT MIN TYP MAX Clock frequency except for Read Data (03h) & DTR instructions (3.0V-3.6V) FR fC1 D.C. 133 MHz Clock frequency except for Read Data (03h) & DTR instructions( 2.7V-3.0V) FR fC1 D.C. 104 MHz Clock frequency for Read Data instruction (03h) fR D.C. 50 MHz Clock High, Low Time for all instructions except for Read Data (03h) tCLH, tCLL(1) 45%PC ns Clock High, Low Time for Read Data (03h) instruction tCRLH, tCRLL(1) 45%PC ns Clock Rise Time peak to peak tCLCH(2) 0.1 V/ns Clock Fall Time peak to peak tCHCL(2) 0.1 V/ns 3 ns 3 ns /CS Active Setup Time relative to CLK tSLCH tCSS /CS Not Active Hold Time relative to CLK tCHSL Data In Setup Time tDVCH tDSU 1 ns Data In Hold Time tCHDX tDH 3 ns /CS Active Hold Time relative to CLK tCHSH 3 ns /CS Not Active Setup Time relative to CLK tSHCH 3 ns /CS Deselect Time (During Read) tSHSL1 tCSH 10 ns /CS Deselect Time (During Erase or Program or Write) tSHSL2 tCSH 50 ns Output Disable Time tSHQZ(2) tDIS 7 ns Clock Low to Output Valid tCLQV1 tV1 6 ns Output Hold Time tCLQX tHO 1.5 ns Continued - next page - 82 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.7 AC Electrical Characteristics (cont'd) SPEC DESCRIPTION SYMBOL ALT UNIT MIN TYP MAX Write Protect Setup Time Before /CS Low tWHSL(3) 20 ns Write Protect Hold Time After /CS High tSHWL(3) 100 ns tDP(2) 3 s /CS High to Standby Mode without ID Read tRES1(2) 3 s /CS High to Standby Mode with ID Read tRES2(2) 1.8 s /CS High to next Instruction after Suspend tSUS(2) 20 s /CS High to next Instruction after Reset tRST(2) 30 s /CS High to Power-down Mode /RESET pin Low period to reset the device tRESET(2) 1(4) s Write Status Register Time tW 10 15 ms Page Program Time tPP 0.4 3 ms Sector Erase Time (4KB) tSE 50 400 ms Block Erase Time (32KB) tBE1 120 1,600 ms Block Erase Time (64KB) tBE2 150 2,000 ms Chip Erase Time tCE 80 400 s Notes: 1. 2. 3. 4. 5. 6. Clock high + Clock low must be less than or equal to Pc. Pc = 1/fc(max.) Value guaranteed by design and/or characterization, not 100% tested in production. Only applicable as a constraint for a Write Status Register instruction when SRP=1. It is possible to reset the device with shorter tRESET (as short as a few hundred ns), a 1us minimum is recommended to ensure reliable operation. Tested on sample basis and specified through design and characterization data. TA = 25 C, VCC = 3.0V 4-bytes address alignment for Quad Read: read address start from A1,A0=0,0 - 83 - W25Q256JV 9.8 Serial Output Timing /CS tCLH CLK IO output 9.9 tCLQV tCLQX tCLQX tCLQV tCLL MSB OUT tSHQZ LSB OUT Serial Input Timing /CS tSHSL tCHSL tSLCH tCHSH tSHCH CLK tDVCH IO input 9.1 tCHDX tCLCH MSB IN tCHCL LSB IN /WP Timing /CS tWHSL tSHWL /WP CLK IO input Write Status Register is allowed - 84 - Write Status Register is not allowed Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.2 PACKAGE SPECIFICATIONs 9.3 8-Pad WFLGA 6x5-mm (Package Code M) Symbol Millimeters Inches Min Nom Max Min Nom Max A 0.70 0.75 0.80 0.0275 0.0295 0.0314 b 0.35 0.40 0.45 0.0137 0.0157 0.0177 D 5.90 6.00 6.10 0.2322 0.2362 0.2401 D2 3.30 3.40 3.50 0.1300 0.1339 0.1378 E 4.90 5.00 5.10 0.1929 0.1968 0.2007 E2 4.20 4.30 4.40 0.1673 0.1692 0.1712 e 1.27 BSC 0.050 BSC L 0.55 0.60 0.65 0.0216 0.0236 0.0255 y --- --- 0.08 --- --- 0.0031 D3 0.35 0.40 0.45 0.0138 0.0157 0.0177 E3 0.35 0.40 0.45 0.0138 0.0157 0.0177 - 85 - W25Q256JV 9.4 8-Pad WSON 8x6-mm (Package Code E) MILLIMETERS Min Nom Max A 0.70 0.75 0.80 A1 0.00 0.02 SYMBOL Min INCHES Nom Max 0.028 0.030 0.031 0.05 0.000 0.001 0.002 0.019 b 0.35 0.40 0.48 0.014 0.016 C --- 0.20 Ref. --- --- 0.008 Ref. --- D 7.90 8.00 8.10 0.311 0.315 0.319 D2 3.35 3.40 3.45 0.132 0.134 0.136 E 5.90 6.00 6.10 0.232 0.236 0.240 E2 4.25 4.30 4.35 0.167 0.169 0.171 e 1.27 BSC 0.050 BSC L 0.45 0.50 0.55 0.018 0.020 0.022 y 0.00 --- 0.05 0.000 --- 0.002 - 86 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.5 16-Pin SOIC 300-mil (Package Code F) Min Millimeters Nom Max Min Inches Nom Max A 2.36 2.49 2.64 0.093 0.098 0.104 A1 0.10 --- 0.30 0.004 --- 0.012 A2 --- 2.31 --- --- 0.091 --- b 0.33 0.41 0.51 0.013 0.016 0.020 Symbol C 0.18 0.23 0.28 0.007 0.009 0.011 D 10.08 10.31 10.49 0.397 0.406 0.413 E 10.01 10.31 10.64 0.394 0.406 0.419 E1 7.39 7.49 7.59 0.291 0.295 0.299 e 1.27 BSC 0.050 BSC L 0.38 0.81 1.27 0.015 0.032 0.050 y --- --- 0.076 --- --- 0.003 0 --- 8 0 --- 8 - 87 - W25Q256JV 9.6 24-Ball TFBGA 8x6-mm (Package Code B, 5x5-1 Ball Array) Note: Ball land: 0.45mm. Ball Opening: 0.35mm PCB ball land suggested <= 0.35mm Symbol Min Millimeters Nom Max Min Inches Nom Max A --- --- 1.20 --- --- 0.047 A1 0.26 0.31 0.36 0.010 0.012 0.014 A2 --- 0.85 --- --- 0.033 --- b 0.35 0.40 0.45 0.014 0.016 0.018 D 7.90 8.00 8.10 0.311 0.315 0.319 D1 E 4.00 BSC 5.90 6.00 0.157 BSC 6.10 0.232 0.236 E1 4.00 BSC 0.157 BSC SE 1.00 TYP 0.039 TYP SD 1.00 TYP 0.039 TYP e 1.00 BSC 0.039 BSC ccc --- --- 0.10 - 88 - --- --- 0.240 0.0039 Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.7 24-Ball TFBGA 8x6-mm (Package Code C, 6x4 Ball Array) Note: Ball land: 0.45mm. Ball Opening: 0.35mm PCB ball land suggested <= 0.35mm Min Millimeters Nom Max Min Inches Nom Max A --- --- 1.20 --- --- 0.047 A1 0.25 0.30 0.35 0.010 0.012 0.014 b 0.35 0.40 0.45 0.014 0.016 0.018 D 7.95 8.00 8.05 0.313 0.315 0.317 6.05 0.234 Symbol D1 E 5.00 BSC 5.95 E1 0.197 BSC 3.00 BSC e ccc 6.00 1.00 BSC --- --- 0.236 0.238 0.118 BSC 0.039 BSC 0.10 - 89 - --- --- 0.039 W25Q256JV 9.8 Ordering Information W(1) 25Q 256J V W = Winbond 25Q = SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O 256J = 256M-bit V = 2.7V to 3.6V F = 16-pin SOIC 300-mil E = 8-pad WSON 8x6mm B = 24-ball TFBGA 8x6-mm (5x5 ball array) I = x I(1) Industrial (-40C to +85C) M = 8-pad WFLGA 6x5-mm C = 24-ball TFBGA 8x6-mm (6x4 ball array) J = Industrial Plus (-40C to +105C) (2,3) Q(4) = Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3) with QE = 1 (fixed) in Status register-2. Backward compatible to FV family. M(5) = Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3) with QE = 0 (programmable) in Status register-2. New device ID is used to identify JV family Notes: 1. The "W" prefix and the Temperature designator "I" are not included on the part marking. 2. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel (shape T) or Tray (shape S), when placing orders. 3. For shipments with special order options, please contact Winbond. 4. /HOLD function is disabled to support Standard, Dual and Quad I/O without user setting. 5. For DTR, QPI supporting, please refer to W25Q256JV DTR datasheet - 90 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 9.9 Valid Part Numbers and Top Side Marking The following table provides the valid part numbers for the W25Q256JV SpiFlash Memory. Please contact Winbond for specific availability by density and package type. Winbond SpiFlash memories use a 12-digit Product Number for ordering. However, due to limited space, the Top Side Marking on all packages uses an abbreviated 10-digit number. W25Q256JV-IQ/JQ valid part numbers: PACKAGE TYPE DENSITY PRODUCT NUMBER TOP SIDE MARKING 256M-bit W25Q256JVFIQ 25Q256JVFQ 256M-bit W25Q256JVMIQ TBD E WSON-8 8x6mm 256M-bit W25Q256JVEIQ 25Q256JVEQ B(1) TFBGA-24 8x6mm (5x5-1 Ball Array) 256M-bit W25Q256JVBIQ 25Q256JVBQ C(1) TFBGA-24 8x6mm (6x4 Ball Array) 256M-bit W25Q256JVCIQ 25Q256JVCQ PACKAGE TYPE DENSITY PRODUCT NUMBER TOP SIDE MARKING 256M-bit W25Q256JVFJQ Q256JVFJQ 256M-bit W25Q256JVMJQ TBD E WSON-8 8x6mm 256M-bit W25Q256JVEJQ Q256JVEJQ B(1) TFBGA-24 8x6mm (5x5-1 Ball Array) 256M-bit W25Q256JVBJQ Q256JVBJQ C(1) TFBGA-24 8x6mm (6x4 Ball Array) 256M-bit W25Q256JVCJQ Q256JVCJQ F SOIC-16 300mil M WFLGA-8 6x5-mm F SOIC-16 300mil M WFLGA-8 6x5-mm Continued - next page - 91 - W25Q256JV W25Q256JV-IM/JM(2,3) valid part numbers: PACKAGE TYPE DENSITY PRODUCT NUMBER TOP SIDE MARKING 256M-bit W25Q256JVFIM 25Q256JVFM 256M-bit W25Q256JVMIM TBD E WSON-8 8x6mm 256M-bit W25Q256JVEIM 25Q256JVEM B(1) TFBGA-24 8x6mm (5x5-1 Ball Array) 256M-bit W25Q256JVBIM 25Q256JVBM C(1) TFBGA-24 8x6mm (6x4 Ball Array) 256M-bit W25Q256JVCIM 25Q256JVCM PACKAGE TYPE DENSITY PRODUCT NUMBER TOP SIDE MARKING 256M-bit W25Q256JVFJM Q256JVFJM 256M-bit W25Q256JVMJM TBD E WSON-8 8x6mm 256M-bit W25Q256JVEJM Q256JVEJM B(1) TFBGA-24 8x6mm (5x5-1 Ball Array) 256M-bit W25Q256JVBJM Q256JVBJM C(1) TFBGA-24 8x6mm (6x4 Ball Array) 256M-bit W25Q256JVCJM Q256JVCJM F SOIC-16 300mil M WFLGA-8 6x5-mm F SOIC-16 300mil M WFLGA-8 6x5-mm Note: 1. These package types are special order, please contact Winbond for more information. 2. For WSON packages, the package type ZP and ZE is not used in the top side marking. 3. For DTR, QPI supporting with ordering options "IM" & "JM", please refer to W25Q256JV DTR datasheet. - 92 - Publication Release Date: October 23, 2018 Revision I W25Q256JV 10. REVISION IISTORY VERSION DATE A 04/01/2013 New Create Preliminary B 09/20/2016 Removed "preliminary" C 10/14/2016 27 Updated instruction set table - 03h D 11/30/2016 44 Updated 6Ch waveform E 02/10/2017 6 Updated WSON 8X6 PIN3 F 05/11/2017 5 90-91 G 08/03/2017 11 H 10/17/2018 I 10/23/2018 PAGE DESCRIPTION Updated /WP information Updated notice for Reset pin Updated W25Q256JV-IM order information Updated Quad SPI instruction description 26 80 82-83 5-6,85,90-91 Added industrial plus Updated 3Ch clock number Added ICC3(typ.) vale Updated tSLC, tCHSL, tDVCH, and tPP(typ.) value Added WSON 6X5 information 5-6,85,90-91 Modify WSON 6X5 to WFLGA 6X5 Trademarks Winbond and SpiFlash are trademarks of Winbond Electronics Corporation. All other marks are the property of their respective owner. Important Notice Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Furthermore, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. Information in this document is provided solely in connection with Winbond products. Winbond reserves the right to make changes, corrections, modifications or improvements to this document and the products and services described herein at any time, without notice. - 93 -