Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC232ALP4E v00.0613 SWITCHES - SPDT - SMT GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Typical Applications Features The HMC232ALP4E is ideal for: * Telecom Infrastructure Isolation: 57 dB @ 3 GHz 50 dB @ 6 GHz * Microwave Radio & VSAT Input P1dB: +30 dBm * Military Radios, Radar & ECM Insertion Loss: 1.5 dB Typical @ 6 GHz * Test Instrumentation Non-Reflective Design 24 Lead 4x4mm QFN Package: 16mm Included in the HMC-DK005 Designer's Kit General Description Functional Diagram The HMC232ALP4E is a broadband high isolation non-reflective GaAs MESFET SPDT switch in a low cost leadless QFN surface mount plastic package. Covering DC to 12 GHz, the switch features >57dB isolation up to 3 GHz and >45 dB isolation up to 12 GHz. Input P1dB compression is +30 dBm typical, while input IP3 is +48 dBm. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. Electrical Specifications, TA = +25 C, With 0/-5V Control, 50 Ohm System Parameter Insertion Loss Isolation DC - 3.0 GHz DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz Min. 52 45 42 40 Typ. Max. Units 1.4 1.5 2.0 2.5 1.7 1.8 2.3 3.1 dB dB dB dB 57 50 47 45 dB dB dB dB Return Loss "On State" DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz 18 14 12 dB dB dB Return Loss RF1, RF2 "Off State" DC - 12.0 GHz 14 dB Input Power for 1 dB Compression 0.5 - 12.0 GHz 26 30 dBm Input Third Order Intercept (Two-Tone Input Power= +10 dBm Each Tone, 1 MHz Tone Separation) 0.5 - 12.0 GHz 45 48 dBm 6 25 ns ns Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 1 Frequency DC - 3.0 GHz DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz DC - 12.0 GHz For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC232ALP4E v00.0613 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Isolation Insertion Loss -10 -20 -30 ISOLATION (dB) INSERTION LOSS (dB) -1 -2 -40 -3 -50 -4 -60 -5 -70 -6 -80 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 FREQUENCY (GHz) +25 C 85 C 7 8 9 10 11 RF1 -40 C Return Loss 12 13 RF2 0.1 and 1 dB Input Compression Point 35 -5 30 P1dB (dBm) 0 -10 -15 25 20 15 -20 10 -25 0 1 2 3 4 5 6 7 8 9 10 11 12 0 13 1 2 3 RFC RF1, RF2 ON 4 5 6 7 8 9 10 11 12 13 FREQUENCY (GHz) FREQUENCY (GHz) 0.1 dB Compression Point 1 dB Compression Point RF1, RF2 OFF Input Third Order Intercept Point 60 55 50 IP3(dBm) RETURN LOSS (dB) 6 FREQUENCY (GHz) SWITCHES - SPDT - SMT 0 45 40 35 30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 FREQUENCY (GHz) +25 C +85 C -40 C For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 2 HMC232ALP4E v00.0613 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz SWITCHES - SPDT - SMT Absolute Maximum Ratings Control Voltages RF Input Power (Vctl = -5V) (0.5 - 12 GHz) Insertion Loss Path Terminated Path +30.9 dBm +23.7 dBm Control Voltage Range (A & B) +1V to -7.5V Channel Temperature 150 C Bias Condition Low 0 to -0.2V @ 0.2 uA Max. High -5V @ 2 uA Typ. to -7V @ 20 uA Typ. (0.5 Vdc) Truth Table Control Input Thermal Resistance (RTH) (channel to ground paddle) Insertion Loss Path Terminated Path State 88.5 C/W 277 C/W Storage Temerature -65 to +150 C Operating Temperature -40 to +85 C Signal Path State A B RFC to RF1 RFC to RF2 High Low ON OFF Low High OFF ON Caution: Do not "Hot Switch" power levels greater than +27 dBm (Vctl = 0/-5 Vdc). ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC232ALP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [1] Package Marking [2] H232A XXXX [1] Max peak reflow temperature of 260 C [2] 4-Digit lot number XXXX 3 For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC232ALP4E v00.0613 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz SWITCHES - SPDT - SMT Suggested Driver Circuit Pin Descriptions Function Description 1, 2, 6, 7, 11, 12, 13, 14, 17, 18, 19, 20, 24 Pin Number N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3, 5, 8, 10, 21, 23 GND Package bottom must also be connected to PCB RF ground. 4, 9, 22 RFC, RF1, RF2 This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. 15 B See truth table and control voltage table. 16 A See truth table and control voltage table. Interface Schematic For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 4 HMC232ALP4E v00.0613 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz SWITCHES - SPDT - SMT Evaluation PCB List of Materials for Evaluation PCB EV1HMC232ALP4 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J6 DC Pin C1, C2 100 pF Capacitor, 0603 Pkg. U1 HMC232ALP4E SPDT Switch PCB [2] 107602 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 5 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC232ALP4E v00.0613 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz SWITCHES - SPDT - SMT Notes: For price, delivery and to place orders: Analog Devices, Inc., 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC232LP4E-AN HMC232LP4ETR-AN HMC232ALP4E HMC232ALP4ETR