ON/OFF
COUT
2.2 µF
ON/OFF
GND
IN
NC
OUT VOUT
VIN
CIN
1 µF LP2980
Copyright © 2016, Texas Instruments Incorporated
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
Reference
Design
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
LP2980-N Micropower 50-mA Ultra-Low-Dropout Regulator in SOT-23 Package
1
1 Features
1• 2.1-V to 16-V Input Voltage Range
• 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V Output Versions
• Ultra-Low-Dropout Voltage
• Output Voltage Accuracy 0.5% (A Grade)
• Ensured 50-mA Output Current
• Requires Only 1-μF External Capacitance
• < 1-μA Quiescent Current When Shutdown
• Low Ground Pin Current at All Load Currents
• High Peak Current Capability (150 mA Typical)
• Wide Supply Voltage Range (16 V Maximum)
• Fast Dynamic Response to Line and Load
• Low ZOUT Over Wide Frequency Range
• Overtemperature and Overcurrent Protection
•−40°C to 125°C Junction Temperature Range
2 Applications
• Cellular Phone
• Palmtop/Laptop Computer
• Personal Digital Assistant (PDA)
• Camcorder, Personal Stereo, Camera
3 Description
The LP2980-N is a 50-mA, fixed-output voltage
regulator designed specifically to meet the
requirements of battery-powered applications.
Using an optimized VIP (Vertically Integrated PNP)
process, the LP2980-N delivers unequaled
performance in all specifications critical to battery-
powered designs:
Dropout voltage: Typically 120 mV at 50-mA load,
and 7 mV at 1-mA load.
Ground pin current: Typically 375 μA at 50-mA load,
and 80 μA at 1-mA load.
Sleep mode: Less than 1-μA quiescent current when
ON/OFF pin is pulled to less than 0.18 V.
Minimum part count: Requires only a 1-μF capacitor
on the regulator output.
Precision output: Initial output voltage tolerance of
±0.5% (A grade).
5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V versions available
as standard products.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LP2980-N SOT-23 (5) 2.90 mm × 1.60 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
2
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Typical Characteristics.............................................. 7
7 Detailed Description............................................ 12
7.1 Overview................................................................. 12
7.2 Functional Block Diagram....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 13
8 Application and Implementation ........................ 14
8.1 Application Information............................................ 14
8.2 Typical Application ................................................. 14
9 Power Supply Recommendations...................... 22
10 Layout................................................................... 22
10.1 Layout Guidelines ................................................. 22
10.2 Layout Example .................................................... 22
11 Device and Documentation Support................. 23
11.1 Device Support...................................................... 23
11.2 Receiving Notification of Documentation Updates 23
11.3 Community Resources.......................................... 23
11.4 Trademarks........................................................... 23
11.5 Electrostatic Discharge Caution............................ 23
11.6 Glossary................................................................ 23
12 Mechanical, Packaging, and Orderable
Information........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision O (June 2015) to Revision P Page
• Changed minor wording in Description for clarity................................................................................................................... 1
• Deleted input supply voltage (operating) row; deleted "(survival)" from rows of Abs Max table ........................................... 4
• Deleted lead temperature from Abs Max per new format rules.............................................................................................. 4
• Added "(operating") from ROC table; add second row for "Shutdown input voltage" to ROC............................................... 4
• Added "High K" and footnote 2 to Thermal Information ........................................................................................................ 4
• Changed "...an output tolerance of %..." to "...an initial output voltage tolerance of ±0.5%..." ........................................... 12
• Deleted "Very high accuracy 1.23-V reference" .................................................................................................................. 12
• Changed "150 mA" to "50 mA" to correct typo from reformat (2 places)............................................................................. 12
• Changed "...only 1 µA" to "...less than 1 µA"........................................................................................................................ 12
• Changed "... pulled low" to "...pulled to less than 0.18 V" ................................................................................................... 12
Changes from Revision N (December 2014) to Revision O Page
• Changed pin names VOUT to OUT and VIN to IN per TI nomenclature; correct typos ....................................................... 1
• Changed format of ESD Ratings table .................................................................................................................................. 4
• Deleted (the TO-220 package alone will safely dissipate this) - no TO-220 package for this part...................................... 20
Changes from Revision M (April 2013) to Revision N Page
• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section; add updated
Thermal Information .............................................................................................................................................................. 1
3
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Changes from Revision L (April 2013) to Revision M Page
• Changed layout of National Semiconductor data sheet to TI format.................................................................................... 22
4
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
5 Pin Configuration and Functions
DBV Package
5 Pin SOT-23
Top View
Pin Functions
PIN I/O DESCRIPTION
NO. NAME
1 IN I Input voltage
2 GND — Common ground (device substrate)
3 ON/OFF I Logic high enable input
4 N/C —
DO NOT CONNECT. Device pin 4 is reserved for post packaging test and calibration of the
LP2980-N VOUT accuracy. Device pin 4 must be left floating. Do not connect to any potential.
Do not connect to ground. Any attempt to do pin continuity testing on device pin 4 is
discouraged. Continuity test results will be variable depending on the actions of the factory
calibration. Aggressive pin continuity testing (high voltage, or high current) on device pin 4
may activate the trim circuitry forcing VOUT to move out of tolerance.
5 OUT O Regulated output voltage
5
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply
when operating the device outside of its rated operating conditions.
(2) If Military/Aerospace-specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, RθJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using P(MAX) = ( (TJ(MAX) – TA) / RθJA).
The value of RθJA for the SOT-23 package is 175.7°C/W. Exceeding the maximum allowable power dissipation will cause excessive die
temperature, and the regulator will go into thermal shutdown.
(4) If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980-N output must be diode-clamped
to ground.
(5) The output PNP structure contains a diode between the IN and OUT pins that is normally reverse-biased. Reversing the polarity from
VIN to VOUT turns on this diode (see Reverse Current Path).
6 Specifications
6.1 Absolute Maximum Ratings(1)(2)
MIN MAX UNIT
Operating junction temperature −40 125 °C
Power dissipation(3) Internally Limited
Input supply voltage −0.3 16 V
Shutdown input voltage −0.3 16 V
Output voltage(4) −0.3 9 V
IOUT Short-circuit protected
Input-output voltage(5) −0.3 16 V
Storage temperature, Tstg –65 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic
discharge Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001(1) All pins except 3 and 4 ±2000 V
Pins 3 and 4 ±1000
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
Operating junction temperature −40 125 °C
Input supply voltage 2.1 16 V
Shutdown input voltage 0 VIN
(1) For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics.
(2) Thermal resistance value RθJA is based on the EIA/JEDEC High-K printed circuit board defined by JESD51-7 - High Effective Thermal
Conductivity Test Board for Leaded Surface Mount Packages.
6.4 Thermal Information
THERMAL METRIC(1) LP2980-N
UNITDBV
5 PINS
RθJA Junction-to-ambient thermal resistance, High K(2) 175.7 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 78 °C/W
RθJB Junction-to-board thermal resistance 30.8 °C/W
ψJT Junction-to-top characterization parameter 2.8 °C/W
ψJB Junction-to-board characterization parameter 30.3 °C/W
6
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
(1) Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of
–40°C to +125°C, unless otherwise stated. Typical values represent the most likely parametric norm at TA= 25°C, and are provided for
reference purposes only.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using statistical
quality control (SQC) methods. The limits are used to calculate average outgoing quality level (AOQL).
(3) Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a
1-V differential.
(4) The ON/OFF inputs must be properly driven to prevent misoperation. For details, see ON/OFF Input Operation.
6.5 Electrical Characteristics
Unless otherwise specified: TJ= 25°C, VIN = VO(NOM) + 1 V, IL= 1 mA, COUT = 1 μF, VON/OFF = 2 V.(1)
PARAMETER TEST CONDITIONS LP2980AI-XX(2) LP2980I-XX(2) UNIT
MIN TYP MAX MIN TYP MAX
ΔVOOutput voltage tolerance
IL= 1 mA −0.5 0.5 −1 1
%VNOM
1 mA < IL< 50 mA −0.75 0.75 −1.5 1.5
1 mA < IL< 50 mA
–40°C ≤TJ≤125°C −2.5 2.5 −3.5 3.5
Output voltage line
regulation
VO(NOM) + 1 V ≤VIN ≤16 V 0.007 0.014 0.007 0.014 %/V
VO(NOM) + 1 V ≤VIN ≤16 V
–40°C ≤TJ≤125°C 0.007 0.032 0.007 0.032
VIN – VODropout voltage(3)
IL= 0 mA 1 3 1 3
mV
IL= 0 mA, –40°C ≤TJ≤
125°C 1 5 1 5
IL= 1 mA 7 10 7 10
IL= 1 mA, –40°C ≤TJ≤
125°C 7 15 7 15
IL= 10 mA 40 60 40 60
IL= 10 mA, –40°C ≤TJ≤
125°C 40 90 40 90
IL= 50 mA 120 150 120 150
IL= 50 mA, –40°C ≤TJ≤
125°C 120 225 120 225
IGND Ground pin current
IL= 0 mA 65 95 65 95
μA
IL= 0 mA, –40°C ≤TJ≤
125°C 65 125 65 125
IL= 1 mA 80 110 80 110
IL= 1 mA, –40°C ≤TJ≤
125°C 80 170 80 170
IL= 10 mA 140 220 140 220
IL= 10 mA, –40°C ≤TJ≤
125°C 140 460 140 460
IL= 50 mA 375 600 375 600
IL= 50 mA, –40°C ≤TJ≤
125°C 375 1200 375 1200
VON/OFF < 0.18 V
–40°C ≤TJ≤125°C 0 1 0 1
VON/OFF ON/OFF input voltage(4)
High = O/P ON
–40°C ≤TJ≤125°C 1.6 1.4 1.6 1.4 V
Low = O/P OFF
–40°C ≤TJ≤125°C 0.55 0.18 0.55 0.18
ION/OFF ON/OFF input current VON/OFF = 0 V 0 −1 0 −1
μA
VON/OFF = 5 V
–40°C ≤TJ≤125°C 5 15 5 15
IO(PK) Peak output current VOUT ≥VO(NOM) −5% 100 150 100 150 mA
enOutput noise voltage
(RMS) BW = 300 Hz to 50 kHz
COUT = 10 μF160 160 μV
ΔVOUT /
ΔVIN Ripple rejection f = 1 kHz
COUT = 10 μF63 63 dB
7
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics (continued)
Unless otherwise specified: TJ= 25°C, VIN = VO(NOM) + 1 V, IL= 1 mA, COUT = 1 μF, VON/OFF = 2 V.(1)
PARAMETER TEST CONDITIONS LP2980AI-XX(2) LP2980I-XX(2) UNIT
MIN TYP MAX MIN TYP MAX
(5) See related curve(s) in Typical Characteristics section.
IO(MAX) Short-circuit current RL= 0 Ω(steady state)(5) 150 150 mA
8
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
6.6 Typical Characteristics
Unless otherwise specified: TA= 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Figure 1. Output Voltage vs Temperature Figure 2. Output Voltage vs Temperature
Figure 3. Output Voltage vs Temperature Figure 4. Dropout Characteristics
Figure 5. Dropout Characteristics Figure 6. Dropout Characteristics
9
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified: TA= 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Figure 7. Dropout Voltage vs Temperature Figure 8. Dropout Voltage vs Load Current
Figure 9. Ground Pin Current vs Temperature Figure 10. Ground Pin Current vs Load Current
Figure 11. Input Current vs VIN Figure 12. Input Current vs VIN
10
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified: TA= 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Figure 13. Line Transient Response Figure 14. Line Transient Response
Figure 15. Load Transient Response Figure 16. Load Transient Response
Figure 17. Load Transient Response Figure 18. Load Transient Response
11
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified: TA= 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Figure 19. Short Circuit Current Figure 20. Instantaneous Short Circuit Current vs
Temperature
Figure 21. Short Circuit Current Figure 22. Output Impedance vs Frequency
Figure 23. Output Impedance vs Frequency Figure 24. Output Noise Density
12
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified: TA= 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN.
Figure 25. Ripple Rejection Figure 26. Input to Output Leakage vs Temperature
Figure 27. Output Reverse Leakage vs Temperature Figure 28. Turnon Waveform
Figure 29. Turnoff Waveform Figure 30. ON/OFF Pin Current vs VON/OFF
13
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
The LP2980-N is a 50-mA, fixed-output voltage regulator designed specifically to meet the requirements of
battery-powered applications. Available in output voltages from 2.5 V to 5 V, the device has an initial output
voltage tolerance of ±0.5% for the A grade (1% for the non-A version). Using an optimized vertically integrated
PNP (VIP) process, the LP2980-N contains these features to facilitate battery-powered designs:
• Fixed 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V output versions
• Low-dropout voltage, typical dropout of 120 mV at 50-mA load current and 7 mV at 1-mA load
• Low ground current, typically 370 μA at 50-mA load and 80 μA at 1-mA load
• A sleep mode feature is available, allowing the regulator to consume less than 1 µA typically when the
ON/OFF pin is pulled to less than 0.18 V.
• Overtemperature protection and overcurrent protection circuitry is designed to safeguard the device during
unexpected conditions.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Multiple Voltage Options
To meet the different application requirements, the LP2980-N provides multiple fixed output options from 2.5 V to
5 V.
7.3.2 High-Accuracy Output Voltage
With special careful design to minimize all contributions to the output voltage error, the LP2980-N distinguishes
itself as a very high-accuracy output voltage micropower LDO. This includes a tight initial tolerance (0.5%
typical), extremely good line regulation (0.007%/V typical), and a very low output voltage temperature coefficient,
making the part an ideal low-power voltage reference.
7.3.3 Ultra-Low-Dropout Voltage
Generally speaking, the dropout voltage often refers to the voltage difference between the input and output
voltage (VDO = VIN – VOUT), where the main current pass-FET is fully on in the ohmic region of operation and is
characterized by the classic RDS(ON) of the FET. VDO indirectly specifies a minimum input voltage above the
nominal programmed output voltage at which the output voltage is expected to remain within its accuracy
boundary.
14
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Feature Description (continued)
7.3.4 Low Ground Current
LP2980-N uses a vertical PNP process which allows for quiescent currents that are considerably lower than
those associated with traditional lateral PNP regulators, typically 370 μA at 150-mA load and 80 μA at 1-mA load.
7.3.5 Sleep Mode
When pulling the ON/OFF pin to low level, LP2980-N enters sleep mode, and less than 1-μA quiescent current is
consumed. This function is designed for the application which needs a sleep mode to effectively enhance battery
life cycle.
7.3.6 Short-Circuit Protection (Current Limit)
The internal current-limit circuit is used to protect the LDO against high-load current faults or shorting events. The
LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources
constant current. Therefore, the output voltage falls when load impedance decreases. If a current limit occurs
and the resulting output voltage is low, excessive power may be dissipated across the LDO resulting in a thermal
shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from damage
under all load conditions. If OUT is forced below 0 V before EN goes high and the load current required exceeds
the foldback current limit, the device may not start up correctly.
7.3.7 Thermal Protection
The LP2980-N contains a thermal shutdown protection circuit to turn off the output current when excessive heat
is dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output
cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The
internal protection circuitry of the LM2980-N is designed to protect against thermal overload conditions. The
circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown
degrades its reliability.
7.4 Device Functional Modes
7.4.1 Operation with VOUT(TARGET) +1V≤VIN < 16 V
The device operates if the input voltage is equal to, or exceeds, VOUT(TARGET) + 0.6 V. At input voltages below the
minimum VIN requirement, the device does not operate correctly and output voltage may not reach target value.
7.4.2 Operation With ON/OFF Control
If the voltage on the ON/OFF pin is less than 0.18 V, the device is disabled, and the shutdown current does not
exceed 1 μA. Raising ON/OFF above 1.6 V initiates the start-up sequence of the device.
15
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP2980-N is a linear voltage regulator operating from 2.1 V to 16 V on the input and regulates voltages
between 2.5 V to 5 V with 0.5% accuracy and 50-mA maximum output current. Efficiency is defined by the ratio
of output voltage to input voltage because the LP2980-N is a linear voltage regulator. To achieve high efficiency,
the dropout voltage (VIN – VOUT) must be as small as possible, thus requiring a very-low-dropout LDO.
Successfully implementing an LDO in an application depends on the application requirements. If the
requirements are simply input voltage and output voltage, compliance specifications (such as internal power
dissipation or stability) must be verified to ensure a solid design. If timing, startup, noise, power supply rejection
ratio (PSRR), or any other transient specification is required, then the design becomes more challenging. This
section discusses the implementation and behavior of the LP2980-N LDO.
8.2 Typical Application
*ON/OFF input must be actively terminated. Tie to IN if this function is not to be used.
**Minimum output capacitance is 1 μF to ensure stability over full load current range. More capacitance provides
superior dynamic performance and additional stability margin (see Output Capacitor Recommendation).
***Do not make connections to this pin.
16
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Typical Application (continued)
8.2.1 Design Requirements
PARAMETER DESIGN REQUIREMENT
Input voltage 5 V ±10%, provided by the DC-DC converter switching at 1 MHz
Output voltage 3.3 V ±5%
Output current 50 mA (maximum), 1 mA (minimum)
RMS noise, 300 Hz to 50 kHz < 1 mVRMS
PSRR at 1 kHz > 40 dB
8.2.2 Detailed Design Procedure
At 50-mA loading, the dropout of the LP2980-N has 225-mV maximum dropout over temperature, thus an 1700-
mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the
LP2980-N in this configuration is VOUT / VIN = 66.7%. To achieve the smallest form factor, the SOT-23 package is
selected. Input and output capacitors are selected in accordance with the Output Capacitor Recommendation
section. With an efficiency of 66.7% and a 50-mA maximum load, the internal power dissipation is 85 mW, which
corresponds to a 14.9°C junction temperature rise for the SOT-23 package. With an 85°C maximum ambient
temperature, the junction temperature is at 99.9°C.
8.2.2.1 Output Capacitor Recommendation
Like any low-dropout regulator, the LP2980-N requires an output capacitor to maintain regulator loop stability.
This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series
resistance (ESR) range. It is not difficult to find capacitors which meet the criteria of the LP2980-N, as the
acceptable capacitance and ESR ranges are wider than for most other LDOs.
In general, the capacitor value must be at least 1 μF (over the actual ambient operating temperature), and the
ESR must be within the range indicated in Figure 31,Figure 32, and Figure 33. It should be noted that, although
a maximum ESR is shown in these figures, it is very unlikely to find a capacitor with an ESR that high.
8.2.2.1.1 Tantalum Capacitors
Surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance
value, and an ESR in the range needed by the LP2980-N.
The results of testing the LP2980-N stability with surface-mount solid tantalum capacitors show good stability
with values of at least 1 μF. The value can be increased to 2.2 μF (or more) for even better performance,
including transient response and noise.
Small value tantalum capacitors that have been verified as suitable for use with the LP2980-N are shown in
Table 1. Capacitance values can be increased without limit.
8.2.2.1.2 Aluminum Electrolytic Capacitors
Although probably not a good choice for a production design, because of relatively large physical size, an
aluminum electrolytic capacitor can be used in the design prototype for an LP2980-N regulator. A value of at
least 1 μF should be used, and the ESR must meet the conditions of Figure 31,Figure 32, and Figure 33. If the
operating temperature drops below 0°C, the regulator may not remain stable, as the ESR of the aluminum
electrolytic capacitor will increase and may exceed the limits indicated in Figure 31,Figure 32, and Figure 33.
Table 1. Surface-Mount Tantalum Capacitor Selection Guide
1-μF SURFACE-MOUNT TANTALUM CAPACITORS
MANUFACTURER PART NUMBER
Kemet T491A105M010AS
NEC NRU105M10
Siemens B45196-E3105-K
Nichicon F931C105MA
Sprague 293D105X0016A2T
17
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
2.2-μF SURFACE-MOUNT TANTALUM CAPACITORS
MANUFACTURER PART NUMBER
Kemet T491A225M010AS
NEC NRU225M06
Siemens B45196/2.2/10/10
Nichicon F930J225MA
Sprague 293D225X0010A2T
8.2.2.1.3 Multilayer Ceramic Capacitors
Surface-mountable multilayer ceramic capacitors may be an attractive choice because of their relatively small
physical size and excellent RF characteristics. However, they sometimes have ESR values lower than the
minimum required by the LP2980-N, and relatively large capacitance change with temperature. The
manufacturer's data sheet for the capacitor should be consulted before selecting a value.
Test results of LP2980-N stability using multilayer ceramic capacitors show that a minimum value of 2.2 μF is
usually needed for the 5-V regulator. For the lower output voltages, or for better performance, a higher value
should be used, such as 4.7 μF.
Multilayer ceramic capacitors that have been verified as suitable for use with the LP2980-N are shown in
Table 2.
Table 2. Surface-Mount Multilayer Ceramic Capacitor Selection Guide
2.2-μF SURFACE-MOUNT CERAMIC
MANUFACTURER PART NUMBER
Tokin 1E225ZY5U-C203
Murata GRM42-6Y5V225Z16
4.7-μF SURFACE-MOUNT CERAMIC
MANUFACTURER PART NUMBER
Tokin 1E475ZY5U-C304
Figure 31. 1-μF ESR Range Figure 32. 2.2-μF ESR Range
VIN VOUT
PNP
GND
18
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Figure 33. 10-μF ESR Range
8.2.2.2 Reverse Current Path
The internal PNP power transistor used as the pass element in the LP2980-N has an inherent diode connected
between the regulator output and input. During normal operation (where the input voltage is higher than the
output) this diode is reverse biased (see Figure 34).
Figure 34. LP2980-N Reverse Current Path
However, if the input voltage is more than a VBE below the output voltage, this diode will turn on and current will
flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into
the VIN pin and out the ground pin, which can damage the part.
The internal diode can also be turned on if the input voltage is abruptly stepped down to a voltage which is a VBE
below the output voltage.
In any application where the output voltage may be higher than the input voltage, an external Schottky diode
must be connected from VIN to VOUT (cathode on VIN, anode on VOUT, see Figure 35), to limit the reverse voltage
across the LP2980-N to 0.3 V (see Absolute Maximum Ratings).
VIN VOUT
PNP
GND
SCHOTTKY DIODE
19
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Figure 35. Adding External Schottky Diode Protection
8.2.2.3 ON/OFF Input Operation
The LP2980-N is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature
is not to be used, the ON/OFF input must be tied to IN to keep the regulator on at all times (the ON/OFF input
must not be left floating).
To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and
below the specified turn-on and turn-off voltage thresholds which ensure an ON or OFF state (see Electrical
Characteristics).
The ON/OFF signal may come from either a totem-pole output, or an open-collector output with a pull-up resistor
to the LP2980-N input voltage or another logic supply. The high-level voltage may exceed the LP2980-N input
voltage, but must remain within the absolute maximum ratings for the ON/OFF pin.
It is also important that the turn-on and turn-off voltage signals applied to the ON/OFF input have a slew rate that
is greater than 40 mV/μs.
NOTE
The regulator shutdown function will not operate correctly if a slow-moving signal is used
to drive the ON/OFF input.
8.2.2.4 Increasing Output Current
The LP2980-N can be used to control higher-current regulators, by adding an external PNP pass transistor. With
the PNP transistors shown in Figure 36, the output current can be as high as 400 mA, as long as the input
voltage is held within the Safe Operation Boundary Curves shown below in Figure 37.
To ensure regulation, the minimum input voltage of this regulator is 6 V. This headroom is the sum of the VBE of
the external transistor and the dropout voltage of the LP2980-N.
20
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Figure 36. 5-V and 400-mA Regulator
Notes:
Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be
used, tie the ON/OFF pin directly to the IN pin.
Note B: Recommended devices (other PNP transistors can be used if the current gain and voltage ratings are
similar).
Note C: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit.
Note D: Increasing the output capacitance improves transient response and increases phase margin.
Note E: Maximum safe input voltage and load current are limited by power dissipation in the PNP pass transistor
and the maximum ambient temperature for the specific application. If a TO-92 transistor such as the MPS2907A
is used, the thermal resistance from junction-to-ambient is 180°C/W in still air.
Assuming a maximum allowable junction temperature of 150°C for the MPS2907A device, the following curves
show the maximum VIN and ILvalues that may be safely used for several ambient temperatures.
Figure 37. Safe Operation Boundary Curves for Figure 36
With limited input voltage range, the LP2980-N can control a 3.3-V, 3-A regulator with the use of a high current-
gain external PNP pass transistor as shown in Figure 38. If the regulator is to be loaded with the full 3 A, heat
sinking will be required on the pass transistor to keep it within its rated temperature range. See Figure 39. For
best load regulation at the high load current, the LP2980-N output voltage connection should be made as close
to the load as possible.
21
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
Although this regulator can handle a much higher load current than can the LP2980-N alone, it can be shut down
in the same manner as the LP2980-N. When the ON/OFF control is brought low, the converter will be in
shutdown, and will draw less than 1 μA from the source.
Figure 38. 5 V to 3.3 V at 3-A Converter
NOTES:
Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be
used, tie the ON/OFF pin directly to the IN pin.
Note B: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit.
Note C: Increasing the output capacitance improves transient response and increases phase margin.
Note D: A heatsink may be required for this transistor. The maximum allowable value for thermal resistance of
the heatsink is dependent on ambient temperature and load current (see curves in Figure 39). Once the value is
obtained from the graph, a heatsink must be selected which has a thermal resistance equal to or lower than this
value. If the value is above 60°C/W, no heatsink is required.
For these curves, a maximum junction temperature of 150°C is assumed for the pass transistor. The case-to-
heatsink attachment thermal resistance is assumed to be 1.5°C/W. All calculations are for 5.5-V input voltage
(which is worst-case for power dissipation).
Figure 39. Heatsink Thermal Resistance Requirements for Figure 38
IN
GND
ON/OFF
OUT
NC
Ground
VOUT
VIN
Input
Capacitor Output
Capacitor
ON/OFF
23
LP2980-N
www.ti.com
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
Product Folder Links: LP2980-N
Submit Documentation FeedbackCopyright © 2000–2016, Texas Instruments Incorporated
9 Power Supply Recommendations
The LP2980-N is designed to operate from an input voltage supply range between 2.1 V and 16 V. The input
voltage range provides adequate headroom for the device to have a regulated output. This input supply must be
well regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output
noise performance.
10 Layout
10.1 Layout Guidelines
For best overall performance, place all circuit components on the same side of the circuit board and as near as
practical to the respective LDO pin connections. Place ground return connections to the input and output
capacitors, and to the LDO ground pin as close as possible to each other, connected by a wide, component-side,
copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and
negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and
thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference
plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB
opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise,
and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this
ground plane is necessary to meet thermal requirements.
10.2 Layout Example
Figure 41. LP2980-N Layout Example
24
LP2980-N
SNOS733P –APRIL 2000–REVISED SEPTEMBER 2016
www.ti.com
Product Folder Links: LP2980-N
Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2980AIM5-2.5 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L0NA
LP2980AIM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L0NA
LP2980AIM5-3.0 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L02A
LP2980AIM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L02A
LP2980AIM5-3.3 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L00A
LP2980AIM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L00A
LP2980AIM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L37A
LP2980AIM5-5.0 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L01A
LP2980AIM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L01A
LP2980AIM5X-2.5 NRND SOT-23 DBV 5 3000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L0NA
LP2980AIM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L0NA
LP2980AIM5X-3.0 NRND SOT-23 DBV 5 3000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L02A
LP2980AIM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L02A
LP2980AIM5X-3.3 NRND SOT-23 DBV 5 3000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L00A
LP2980AIM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L00A
LP2980AIM5X-4.7/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L37A
LP2980AIM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L01A
LP2980IM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L0NB
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2980IM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L02B
LP2980IM5-3.3 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L00B
LP2980IM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L00B
LP2980IM5-3.8/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L21B
LP2980IM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L37B
LP2980IM5-5.0 NRND SOT-23 DBV 5 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L01B
LP2980IM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L01B
LP2980IM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L0NB
LP2980IM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L02B
LP2980IM5X-3.3 NRND SOT-23 DBV 5 3000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L00B
LP2980IM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L00B
LP2980IM5X-5.0 NRND SOT-23 DBV 5 3000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 L01B
LP2980IM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L01B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 3
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP2980AIM5-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-3.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-2.5 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-3.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-3.3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-3.3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-5.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2980AIM5-2.5 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-3.0 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 2
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2980AIM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980AIM5X-2.5 SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-3.0 SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0
LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 3
www.ti.com
PACKAGE OUTLINE
C
0.22
0.08 TYP
0.25
3.0
2.6
2X 0.95
1.9
1.45
0.90
0.15
0.00 TYP
5X 0.5
0.3
0.6
0.3 TYP
8
0 TYP
1.9
A
3.05
2.75
B
1.75
1.45
(1.1)
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/E 09/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
0.2 C A B
1
34
5
2
INDEX AREA
PIN 1
GAGE PLANE
SEATING PLANE
0.1 C
SCALE 4.000
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ARROUND 0.07 MIN
ARROUND
5X (1.1)
5X (0.6)
(2.6)
(1.9)
2X (0.95)
(R0.05) TYP
4214839/E 09/2019
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
PKG
1
34
5
2
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED METAL
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
(2.6)
(1.9)
2X(0.95)
5X (1.1)
5X (0.6)
(R0.05) TYP
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/E 09/2019
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
SYMM
PKG
1
34
5
2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
