MS & 97B - Series ACRMS02 0313 I ntroduction & Page Contents Introduction Amphenol MS & 97B series are two series of thread & Bayonet coupled connectors designed to meet the operating requirements of MIL-C-5015. available in a variety of styles & classes, these connectors are primarily used in a range of military and industrial applications where specific degrees of environmental protection are required. Although MS series have identical insert arrangements and other similar components parts, the two series differ in that Amphenol MS series of connectors are also qualified to meet the operating requirements of Defence Standard Joint Services Specifications JSS50812, issued by the Electronics Components Standardization Organisation (LCSO) Amphenol 97B connectors feature a quick a mating bayonet coupling with an audible full mating feature. This series uses the same MIL-C-5015 insert patterns and are used in high shock and vibration environments encountered in commercial, geophysical, aerospace, ground support and shipboard applications. Content Page 1 Introduction 2-3 Connector style General description 4 Electrical data 5 Insert orientations 6 Insert arrangements 7-17 MS threaded series connector 19-22 97B reverse bayonet connector 23-49 Ordering information 50 1 C onnector Styles Class F MS-3108 MS-4108 Class A=R MS-3106 MS-4106 Class A MS-3100 MS-4100 Class E and F MS-3101 MS-4101 Class R cable clamp back shell grommet sleeve 2 grommet MS-3102 MS-4102 C onnector Styles Class F 97B - 3108 97B - 4108 Class A=R 97B - 3106 97B - 4106 Class A 97B - 3100 97B - 4100 Class F 97B - 3101 97B - 4101 97B - 3103 97B - 4103 Class R cable clamp back shell grommet sleeve grommet 97B - 3102 97B - 4102 3 G eneral Description These electrical connectors are designated MS because the interchangeability and operating characteristics are determined by U.S. Military Specifications. These specifications are revised from time to time to incorporate performance requirements dictated by design advances and more stringent requirements of allied equipment. The several designations of MS and 97B connectors meet different requirements of MILC-5015. These designations and general descriptions are as follows : Inserts and grommet Synthetic inserts and grommet manufactured according to MIL-R-3065, offer high dielectric strength and are resistant to oils, gasoline and low temperature. DAP is dimensionally stable, has high arc resistance and high insulation resistance under both humidity and thermal stress. General description Plugs are available in A, F and R types. Receptacles are available in A, E, F and R types. Shell Shell constructions include solid back shell (A) and environmental resistant (E, F & R). Environmental resistant connectors provide a moisture barrier and assure a positive seal. Shell styles consist of wall type receptacles (3100), cable receptacles (3101), box receptacles (3102), straight plugs (3106) and angle plugs (3108). Shell hardware is manufactured from aluminium alloy and cadmium plated with olive drab chromate finish. This finish has excellent conductivity; it is non-reflecting and corrosion resistant. Black anodised finish and cadmiumfree zinc plating with olive drab chromate finish are also available. For details, contact factory. Contacts Pin and socket contacts are of brass and generally silver plated. Gold plating is also available. For details contact factory. These contacts are available for solder or crimp termination. Special arrangements of contacts for pre-mating and pre-earth are also available. A Solid back shell Intended for general service usage to provide convenient means of connecting and disconnecting electrical circuits in industrial and military applications. Environmental resisting Intended for use where the connector will be subject to heavy condensation and rapid changes in temperature or pressure and/or where the connector is subjected to high vibratory conditions. E Environmental resisting with grommet seal and strain relief backshell except for 3102 type. F Environmental resisting with grommet seal, strain relief backshell and front gasket seal for plug type. R Environmental resisting with grommet seal, shorter and lightweight. Features for 97B reverse bayonet coupling connectors with Mil-C-5015 insert patterns: Available in both crimp and solder terminations Contacts available in gold and silver plating Numerous finishes available Zinc alloy plating (cadmium free) available Quick positive coupling Audible and tactile indication of full coupling Waterproof No lockwiring required High shock and vibration capabilities Rugged construction; aluminum or stainless steel components Intermateable with existing VG95234 connectors 500 couplings minimum Insert available in Neoprene material (alternate inserts materials available upon request) Operating temperature range with Neoprene 0 inserts: -55C to +125C0 4 E lectrical Data Dielectric strength Service rating Test Voltage Vac rms Inst. 1000V A 2000V D 2800V E 3500V B 4500V C 7000V Contact rating Contact Size Rated Current Contact Resistance miliohms 16 13A 3.46 12 23A 1.83 8 46A 0.52 4 80A 0.26 0 150A 0.14 Service rating Operating Voltage DC at Sea Level Operating Voltage AC at Sea Level Inst. 250V 200V A 700V 500V D 1250V 900V E 1750V 1250V B 2450V 1750V C 4200V 3000V Service rating 5 I nsert Orientation To avoid cross-plugging problems in applications requiring the use of more than one connector of the same size and arrangement, alternate insert rotations are available as indicated in the accompanying chart. The following insert arrangements have the same alternate insert rotations for W, X, Y and Z which are as below : Degree As shown in the daigram below, the front face of the pin insert is rotated within the shell in a clockwise direction from the normal shell key. The socket insert would be rotated counterclockwise the same number of degrees with respect to the normal shell key. B B Position W Position X B B A A Position Y Position Z Views looking into front face of pin insert or rear of socket insert Insert Arrangement 12S-3 14S-2 14S-5 14S-7 14S-9 16-9 16-10 16-11 16-13 16S-1 16S-4 16S-5 16S-6 16S-8 18-1 18-3 18-4 18-8 18-10 18-11 18-12 18-15 18-20 18-22 18-29 20-3 20-4 20-5 Degrees W X Y Z 70 90 70 35 90 35 35 80 35 70 90 70 35 35 70 80 90 70 90 70 45 35 145 120 110 180 145 110 180 110 110 110 145 180 170 145 110 110 120 170 120 180 145 180 145 110 110 215 240 270 215 250 270 250 250 250 215 270 265 215 250 250 240 265 240 270 215 270 215 250 250 290 290 325 325 325 280 325 290 290 325 325 290 280 290 290 325 Insert Arrangement 20-6 20-15 20-17 20-18 20-19 20-21 20-23 20-24 20-27 20-29 22-1 22-2 22-4 22-5 22-8 22-9 22-10 22-11 22-13 22-20 22-22 22-23 22-27 22-28 24-2 24-9 24-10 24-11 X Y Z 80 110 250 280 16-7 20-16 18-5 20-20 18-9 20-22 18-13 22-3 18-14 22-6 20-7 22-12 20-8 22-14 20-9 22-15 20-12 22-16 20-14 22-17 A A W Degrees W X Y Z 70 80 90 35 90 35 35 35 35 80 35 70 35 35 35 70 35 35 35 35 35 80 80 80 35 80 35 145 180 110 180 110 110 110 110 110 145 110 110 110 145 110 110 110 110 110 110 110 215 270 250 270 250 250 250 250 250 215 250 250 250 215 250 250 250 250 250 250 250 250 250 290 280 325 325 325 325 325 280 325 290 325 325 325 290 325 325 325 325 280 280 280 325 280 325 6 22-18 22-19 22-21 22-24 22-25 22-29 22-33 22-34 24-1 24-3 24-4 24-5 24-6 24-7 24-12 24-14 24-16 24-17 24-20 Insert Arrangement 24-22 24-27 28-2 28-3 28-5 28-6 28-7 28-12 28-18 28-22 32-8 36-3 36-4 36-5 36-6 36-9 36-10 36-14 36-15 40-56 24-21 24-28 28-1 28-4 28-8 28-9 28-10 28-11 28-14 28-15 28-16 28-17 28-19 28-20 28-21 32-1 32-3 32-4 36-1 36-7 36-8 36-13 Degrees W X Y Z 45 80 35 70 35 70 35 90 70 70 80 70 70 35 80 80 90 60 72 110 110 145 110 145 110 180 145 145 125 145 145 120 110 125 125 180 125 144 250 250 215 250 215 250 270 215 215 235 215 215 240 250 235 235 270 245 216 280 325 290 325 290 325 290 290 280 290 290 325 280 280 305 288 I nsert Arrangements Insert Service Total Contact Size Arran- Rating Contgement acts 0 4 8 12 16 10S-2 A 1 1 10SL-3 A 3 3 10SL-4 A 2 2 12S-3 A 2 2 12S-4 D 1 1 12-5 D 1 1 3 3 14S-1 A 14S-2 Inst 4 4 14S-4 D 1 1 14S-5 Inst 5 5 14S-6 Inst 6 6 14S-7 A 3 3 14S-9 A 2 2 14S-10 Inst 4 4 14S-12 A 3 3 14-3 A 1 1 14S-A7 A 19 19 16S-1 A 7 7 16S-3 B 1 1 16S-4 D 2 2 16S-5 A 3 3 16S-6 A 3 3 16S-8 A 5 5 16-2 E 1 1 16-7 A 3 1 2 16-9 A 4 2 2 16-10 A 3 3 16-11 A 2 2 16-12 A 1 1 16-13 A 2 2 18-1 A/Inst 10 10 18-3 D 2 2 18-4 D 4 4 18-5 D 3 2 1 18-06 6 4 2 18-6 D 1 1 18-7 B 1 1 18-8 A 8 1 7 18-9 Inst 7 2 5 18-10 A 4 4 18-11 A 5 5 18-12 A 6 6 18-13 A 4 1 3 18-14 A 2 1 1 18-15 A 4 4 18-16 C 1 1 18-17 Inst 7 2 5 18-19 A 10 10 18-20 A 5 5 18-22 D 3 3 18-24 A/Inst 10 10 18-29 A 5 5 18-30 A 5 5 18-31 A 5 5 20-2 1 1 20-3 D 3 3 20-4 D 4 4 20-6 D 3 3 20-7 D/A 8 8 Insert Service Total Contact Size Arran- Rating Contgement acts 0 4 8 12 16 20-8 Inst 6 2 4 20-9 D/A 8 1 7 20-11 Inst 13 13 20-12 A 2 1 1 20-14 A 5 2 3 20-15 A 7 7 20-16 A 9 2 7 20-17 A 6 5 1 20-18 A 9 3 6 20-19 A 3 3 20-20 A 4 1 3 20-21 A 9 1 8 20-22 A 6 3 3 20-23 A 2 2 20-24 A 4 2 2 20-25 Inst 13 13 20-27 A 14 14 20-29 A 17 17 20-30 Inst 13 13 20-33 A 11 11 20-A48 A 19 22-1 D 2 2 22-2 D 3 3 22-4 A 4 2 2 22-5 D 6 2 4 22-6 D 3 2 1 22-7 E 1 1 22-8 E 2 2 22-9 E 3 3 22-10 E 4 4 22-11 B 2 2 22-12 D 5 2 3 22-13 D/A 5 4 1 22-14 A 19 19 22-15 E/A 6 5 1 22-16 A 9 3 6 22-17 D/A 9 1 8 22-18 D/A 8 8 22-19 A 14 14 22-20 A 9 9 22-21 A 3 1 2 22-22 A 4 4 22-23 D/A 8 8 22-24 D/A 6 2 4 22-27 D/A 9 1 8 22-28 A 7 7 22-34 D 5 3 2 24-2 D 7 7 24-3 D 7 2 5 24-4 1 3 24-5 A 16 16 24-6 D/A 8 8 4 2 24-06 A 6 24-7 A 16 2 14 24-9 A 2 2 24-10 A 7 7 7 Insert Service Total Contact Size Arran- Rating Cont0 4 8 12 16 gement acts 24-11 24-12 A A 9 5 24-16 24-17 24-20 24-21 24-22 24-27 24-28 28-1 28-2 28-3 28-4 28-5 28-6 28-7 28-8 28-9 28-09 28-10 28-11 28-12 28-13 28-15 28-16 28-17 28-18 28-19 28-20 28-21 28-22 28-51 32-1 32-3 D/A D D D D E Inst D/A D E E/D D D D E/D/A D A D/A A A A A A B/D/A C/D/A/Inst B/D/A A A D D D/A D 7 5 11 10 4 7 24 9 14 3 9 5 3 2 12 12 9 7 22 26 26 35 20 15 12 10 14 37 6 12 5 9 D 32-5 A 32-6 32-7 INST,A 32-8 A 32B-13 D D 32-17 A 32-22 2 23 35 30 13 4 54 36-1 36-3 36-4 36-5 36-6 36-7 36-8 36-9 36-10 36-11 36-12 36-13 36-14 36-15 36-16 36-17 38-18 36-20 36-46 36-52 40-56 40-63 22 6 3 4 6 47 47 31 48 48 48 17 16 35 47 47 31 34 27 52 85 61 D D D/A A A A A A A A A E/A D D/A A A A A A A A A 3 2 1 3 2 2 1 4 6 3 3 3 9 9 7 24 3 6 2 12 3 2 1 2 3 2 4 2 2 3 2 1 2 7 2 2 10 6 6 5 3 4 18 26 26 35 20 15 12 4 6 10 4 37 3 12 3 2 4 2 2 3 2 16 7 28 6 24 13 4 54 3 3 4 2 4 18 3 4 1 1 7 40 1 46 2 14 14 48 48 48 2 15 5 5 6 35 7 40 7 40 2 14 14 2 2 30 27 52 85 I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND B A A 16 B C 12 8 0 4 A B Insert arrangement Service rating Number of contacts Contact size Premating contact Front of socket insert 10SL-3 A 3 16 C 10S-2 A 1 16 G 10SL-4 A 2 16 14S-1 C A A F E Front of socket insert B C 12S-3 A 2 16 A B C B 14S-1 A 3 16 B A 14S-2 Inst. 4 16 14S-4 D 1 16 14S-7 A 3 16 B D C A B C 14S-9 A 2 16 B 100 0 rotation of 14S-2 100 0 rotation of 14S-7 *14S-10 Inst. 4 16 *14S-12 A 3 16 B A C 16S-4 D 2 16 *14-3 A 1 8 16S-5 A 3 16 A 8 B C 16S-1 A 7 16 G E C A D B *Not tooled up, can be tooled up on request. Contact Factory. A G D B *16S-3 B 1 16 14S-6 Inst. 6 16 E A B A Insert arrangement Service rating Number of contacts Contact size Premating contact 14S-5 Inst. 5 16 F A B Insert arrangement Service rating Number of contacts Contact size Premating contact C D C 14S-A7 A 7 16 C E B D D Insert arrangement Service rating Number of contacts Contact size Premating contact A F A E D B 12-5 D 1 12 12S-4 A 1 16 16S-6 A 3 16 B C A B 16S-8 A 5 16 E *16-2 E 1 12 I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A B A C D H A A F J C 16-9 A 2 2 12 16 16-10 A 3 12 B D B C 16-11 A 2 12 B A C B *16-13 A 2 12 E A A C A 16-12 A 1 4 B F D C B D E Insert arrangement 18-1 Service rating B,C,F,G=A;Bal.=Inst. Number of contacts 10 Contact size 16 Premating contact F A E G D *18-6 D 1 4 18-06 A 2 4 16 12 E B B 18-5 D 2 1 12 16 C C E H D 18-4 D 4 16 A 18-3 D 2 12 G F A D C A B C 18-7 B 1 8 F A D B C E A D B D 18-8 A 1 7 12 16 H 18-9 Inst. 2 5 12 16 18-10 A 4 12 D 18-11 A 5 12 E F A B B 18-12 A 6 16 C or D A C B B E D B G D C D E A C C Insert arrangement Service rating Number of contacts Contact size Premating contact A B B A I 0 4 B 16-7 A 1 2 8 16 C G 8 B C Insert arrangement Service rating Number of contacts Contact size Premating contact 12 16 *18-13 A 1 3 8 12 A E C A G F B D A A H J C K o 100 - rotation of 18-9 Insert arrangement Service rating Number of contacts Contact size Premating contact *18-14 A 1 1 4 16 18-15 A 4 12 18-16 C 1 12 *Not tooled up, can be tooled up on request. Contact Factory. 9 *18-17 Inst. 2 5 12 16 18-19 A 10 16 K 18-20 A 5 16 D I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND H C B A A B A G I B F J C C D E E 20-2 D 1 0 - E 20-3 D 4 12 A A C B A H G F B B B H C F B B C *18-31 A 5 16 C A G H C A 260 rotation of 18-20 110 rotation of 18-20 *18-30 A 5 16 C *18-29 A 5 16 D A A 0 0 - 0 - *18-24 B,C,F,G=A;Bal.=Inst. 10 16 D 4 D D 250 - rotation of 18-1 18-22 D 3 16 C 8 B A C D o Insert arrangement Service rating Number of contacts Contact size Premating contact B A 12 C E E 16 G J C F C C E B D E A D D E F D Insert arrangement Service rating Number of contacts Contact size Premating contact 20-4 D 4 12 C or D L B E M N 20-7 A,B,H,G=D;C,D,E,F=A 8 16 A *20-6 D 3 16 A G F A D D G E A B H K 20-9 H=D;Bal.=A 1 7 12 16 H B I D C D 20-11 Inst. 13 16 A H G F D B C B F 20-18 A 3 6 12 16 D 20-19 A 3 8 C 20-20 A 1 3 4 12 A *Not tooled up, can be tooled up on request. Contact Factory. 10 20-16 A 2 7 12 16 E A F C B 20-17 A 5 1 12 16 E or F F A H G B D Insert arrangement Service rating Number of contacts Contact size Premating contact A C C E 20-15 A 7 12 A or D A A I D B 20-14 A 2 3 8 12 D *20-12 A 1 1 4 16 H C C Insert arrangement Service rating Number of contacts Contact size Premating contact E G E B J 20A - 9 A 9 12 F A F E A C 20-8 Inst. 2 4 8 16 A B I E C D E A B D B C *20-21 A 1 8 12 16 1 20-22 A 3 3 8 16 20-23 A 2 8 I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND L A J B N G B D F A D K I M J F C 0 B N L C E F N G P S C B M D H K E A D R J D 4 T K E G C A L L H 8 M B N H K 12 A C E M 16 J F H G _ 0 100 rotation of 20-11 Insert arrangement Service rating Number of contacts Contact size Premating contact 20-24 A 2 2 8 16 *20-25 Inst. 13 16 B M U K C H *20-30 Inst. 13 16 B D P C J D H R S A A N V T L F 20-29 A 17 16 G 20-27 A 14 16 M L M A A K J o 250 rotation of 20-11 E B A C B B C D G F E Insert arrangement Service rating Number of contacts Contact size Premating contact 20-33 A 11 16 E F 20 A - 48 A 19 16 22-2 D 3 8 A *22-4 A 2 2 8 12 C A A E 22-1 D 2 8 A B B B A C C D Insert arrangement Service rating Number of contacts Contact size Premating contact 22-5 D 2 4 12 16 D 22-7 E 1 0 *22-6 D 2 1 8 16 B A E B C 22-9 E 3 12 A *22-8 E 2 12 A D B K E A J U D C 22-12 D 2 3 8 16 A *Not tooled up, can be tooled up on request. Contact Factory. 11 22-13 E=D;A,B,C,D=A 4 1 12 16 E C R H D G 22-11 B 2 16 B P S B A N Y T B 22-10 E 4 16 C M L A D C Insert arrangement Service rating Number of contacts Contact size Premating contact B C F E 22-14 A 19 16 A I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 A F H G B F C C C Insert arrangement 22-15 Service rating D=E;A,B,C,E,F=A Number of contacts 5 1 Contact size 12 16 Premating contact D E D E 22-16 A 3 6 12 16 D *22-17 A=D;Bal.=A 1 8 12 16 E D B 22-19 A 14 16 F H 22-22 A 4 8 C or D D F A F 22-27 J=D;Bal.=A 1 8 8 16 A B B G E E D 22-28 A 7 12 G C A C B G E B 24-4 C C H J D A H F B K M L C G B E G F D D A D D C D E F 22-24 C,D,E=D;A,B,F=A 2 4 12 16 D B C G 22-23 H=D;Bal.=A 8 12 A or D G E E C A B J C D *22-21 A 1 2 0 16 22-20 A 9 16 D F B E B B Insert arrangement Service rating Number of contacts Contact size Premating contact D A F F H C C F A A A B E E C 22-18 A,B,F,G,H=D;C,D,E=A 8 16 D G A C G D A J F D N D H G C M H B F F E D P 0 B L J H J J A K A G A G E B A H B 4 N A P E D C R S Insert arrangement Service rating Number of contacts Contact size Premating contact *22-34 D 3 2 12 16 E 24-2 D 7 12 A *24-3 D 2 5 12 16 D *Not tooled up, can be tooled up on request. Contact Factory. 12 24-4 A 3 1 16 0 - 24-5 A 16 16 S 24-6 A,G,H=D;Bal.=A 8 12 D I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND D E A L A K J 12 8 F B C M P 16 0 A A B C A B E N 4 B G D E F D O E I D B C 24-06 Insert arrangement Service rating Number of contacts Contact size Premating contact 24-7 A 2 14 12 16 G 24-9 A 2 4 B C A *24-16 A,B,F,G=D;C,D,E=A 1 3 3 8 12 16 G 24-12 A 2 3 4 12 A A A F B G C B E E K F L B G M C H N E D H A 24-21 D 1 9 8 16 E K B Q J G C R S T W X U V P Y Z G F B M 24-28 Inst. 24 16 *24-27 E 7 16 D *Not tooled up, can be tooled up on request. Contact Factory. 13 28-1 A,J,E=D;Bal.=A 3 6 8 12 E F *28-2 D 2 12 12 16 E C D N D E 24-22 D 4 8 D H A L J C D Insert arrangement Service rating Number of contacts Contact size Premating contact D E 24-20 D 2 9 12 16 A J P K F D *24-17 D 2 3 12 16 D B C J L F A H G C G D 24-11 A 3 6 8 12 E B H K E C E G B D A J C B F 24-10 A 7 8 D or E or G D A A E D I H G 24-06 A 2 4 16 8 Insert arrangement Service rating Number of contacts Contact size Premating contact G C F H E I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A A S A B A B E C P C D C B B E G F C D Insert arrangement Service rating Number of contacts Contact size Premating contact 28-3 E 3 8 A *28-5 D 2 1 2 4 12 16 *28-4 G,S,P=E;Bal.=D 2 7 12 16 E J H H A A G M A B 28-6 D 3 4 A B F L C A K G B M B D L C F E C D 28-7 D 2 4 Insert arrangement Service rating Number of contacts Contact size Premating contact G B V W X P R S L N A F B M C L H D X J C U N G C D E F b Z M A B S a T d V W H R P B T d Y K A b Z H G 28-09 A 5 4 16 4 S a G T M I D R P E K J D 28-9 D 6 6 12 16 E J N U E E 28-8 L,M=E;B=D;Bal.=A 2 10 12 16 D A F F E L Y K X U H G o F 100 rotation of 28-12 Insert arrangement Service rating Number of contacts Contact size Premating contact 28-10 G=D;Bal.=A 2 2 3 4 8 12 G 28-11 A 4 18 12 16 M *Not tooled up, can be tooled up on request. Contact Factory. 14 28-12 A 26 16 H *28-13 A 26 16 H D E W J C V I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A J H A B E D C L K M e f g M H C S H V N U R Q P G F E 8 4 E 0 A L B K L F K C R M P J M D N E H k l F m G 28-15 A 35 16 M 28-16 A 20 16 F J A N K A B G 28-19 H,M=B;A,B=D;Bal.=A 4 6 12 16 H D A F N V P W R X Z a b c d e Y B f g l h m j k n p E 28-21 A 37 16 A A B J M U 28-20 A 10 4 12 16 E A H L T E K C G K S D H N F C L M G F H E P E M J J B C H C K 28-18 M=C;G,H,J,K,L=D;A,B=ABal.=Inst. 12 16 *28-17 R=B;M,N,P=D;A to L=A 15 16 N B A L Insert arrangement Service rating Number of contacts Contact size Premating contact C D J 12 D h j Insert arrangement Service rating Number of contacts Contact size Premating contact L T A G N PX R Y S Z T a U b V c W d B B K J G F 16 A E B B D E L D 28-22 D 3 3 4 16 C F M F C G D E D J C H Insert arrangement Service rating Number of contacts Contact size Premating contact 28-51 D 12 12 32-1 A=E;B,C,D,E=A 2 3 0 12 *Not tooled up, can be tooled up on request. Contact Factory. 15 *32-3 D 1 2 2 4 0 4 12 16 32-5 D 2 0 I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A B G H L P W X J K M N R S Z T O h K S L F e j X W f g X Z T a U 4 0 A G B M k Y V U 8 E R d Y 12 J c F I P W D C E 16 H C N D I b V Insert arrangement Service rating Number of contacts Contact size Premating contact O 32-7 INST , A 4 24 7 16 12 32-6 A 16 2 3 2 16 12 8 4 A M C T D N c Z V P a e K W b R e h i y AA z AD 1 11 13 AG A B C E F G A F D 9 H B 2 12 J I 8 K L M N E 3 32B13 O 7 Insert arrangement Service rating Number of contacts Contact size Premating contact P R S U V W T D C 4 6 AC AE 32-22 A 54 16 32-17 D 4 4 32-8 A 6 24 12 16 S 10 w x AF Insert arrangement Service rating Number of contacts Contact size Premating contact r v AB B C S 5 32B-13 D 13 8 *36-1 D 4 18 12 16 *Not tooled up, can be tooled up on request. Contact Factory. 16 f j n m o L X W a Z d l k G R Y Y c g C P U X F J M O T b B J H L N E O d G K S B D F A I U A D H Y 36-3 D 3 3 0 12 I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A A A B F B D C B E C C Insert arrangement Service rating Number of contacts Contact size Premating contact 36-4 A=D;B,C=A 3 0 A C K O P R V a h Y d Z e n N S T b f c g k vv w W x A H O V J P W d K Q X e l Y m t L R f N a p H U b j r w C T h v y M Z n G S g u A F O c V k J P W d s Q B e f e t u T h j c k s G N x V D J P W d Q X t R f m S g u N T a h p v y G M Z n o F L Y e l B E K z 100 rotation of 36-10 *36-11 A 48 16 A 17 O U b r w H N a p v y 36-10 A 48 16 A *Not tooled up, can be tooled up on request. Contact Factory. S g C G M Z C F L T A L n z R X c *36-9 A 1 2 14 14 4 8 12 16 P F R f m K W b t B Y o Insert arrangement Service rating Number of contacts Contact size Premating contact r p E K X l x D H e *36-8 A 1 46 12 16 Y B E A P w z y E J V j u v *36-7 A 7 40 12 16 x or y D k n s D I O Y a d h M U a d L R V Z m y C M Y g z Insert arrangement Service rating Number of contacts Contact size Premating contact K P U c f s y S Z H X b m p r J O T N S X l u I 36-6 A 2 4 0 4 C E F G W j A B D E G J M I U 36-5 A 4 0 B D F H L D j r w U b k s x z 250 rotation of 36-10 *36-12 A 48 16 A c I nsert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A J P S R B N K L P P M K R S H B E W g Y X F G K J E D V f h Z G E F e m L D G D M C Q H a M N J C U j b N L T d k c C Q A A B Q I H F Insert arrangement Service rating Number of contacts Contact size Premating contact A D C F H L P K O U Y d h Z e B E I R V W l U Y d c g k w u F H L P X v h m Z e S E R V W G J M S N T b f a l w g V M v I O J B f b W c X K R T A C H P R X d D J 100orotation of 36-9 *36-16 A 7 40 12 16 x or y *36-17 A 7 40 12 16 x or y *36-18 A 1 2 14 16 4 8 12 16 Y A F L T Z U a N V b j k m J W R P B G H N A E L M L E F T K a g W U V T B F M U C H N V D J P W A X Y S b j c k d m f n g p h i Z d s X Y c t u v w j t u v AD AE z AA AB AC AD AE AF AH b d c W f p n m M V U g r p AF w x y z AH AJ AK AL AA Z s AB AM AN x AP y b a k L K T h r AC a i J S Z D C H R Y X Z q P N S B F E K R W c f h C D G M e AR AZ AS BA BJ AT BB BK X AU BC LB BS AV BT AW BD BM BE BN BU AX BF BP BV AY BH BR Y 40 - 56 Insert arrangement Service rating Number of contacts Contact size Premating contact G N 250 rotation of 36-7 B E K S o L F 100 rotation of 36-7 Insert arrangement Service rating Number of contacts Contact size Premating contact *36-20 A 2 2 30 8 12 16 k 36-46 A 27 16 *Not tooled up, can be tooled up on request. Contact Factory. 36-52 A 52 16 18 A H p z o D E e s z U a Y m y y Z P c k u d X r y y B I j n p s r A D C K O N T b f a j n G J M S *36-15 M=D;Bal=A 35 16 J *36-14 D 5 5 6 8 12 16 *36-13 N,P,Q=E;Bal.=A 2 15 12 16 40-56 A 85 16 40-63 A 61 16 C MIL -C-5015 MS Threaded Version connector S hell style Wall mounting receptacle MS-3100 MOUNTING HOLES 4.39 DIA. FOR SIZE 32 AND 36 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES 4.55 DIA. FOR 40 SIZE MS-4100 M K V S R S PANEL OPENING R A All dimensions are in mm Connector Size A Thread in inches K M O R S V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2.00-18 UNS 2 1/4-16 UN 2 1/2-16 UN 1.98 1.98 1.98 1.98 1.98 1.98 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.45 14.29 14.29 19.05 14.29 19.05 14.29 19.05 19.05 19.05 19.05 20.64 20.64 22.25 22.22 22.22 20.62 20.62 20.62 23.82 23.82 26.97 26.97 30.17 33.32 36.52 39.67 46.02 53.0 58.72 62.00 18.25 20.64 20.64 23.02 23.02 24.61 24.61 26.99 29.37 31.75 34.92 39.69 44.45 49.21 55.58 25.68 27.76 27.76 30.43 30.43 32.82 32.82 35.07 38.38 41.55 44.70 51.08 57.15 63.78 69.85 5/8-24 NEF 11/16-24NEF 11/16-24NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN Cable Connecting Receptacle MS-3101 MS-4101 V A All dimensions are in mm Connector Size A Thread in inches V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN 19 S hell style Box mounting receptacle MS-3102 MOUNTING HOLES 4.39 DIA. FOR SIZE 32 AND 36 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES 4.55 FOR 40 SIZE MS-4102 L S N R S M K R A All dimensions are in mm Connector Size A Thread in inches K L M N R S 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 1.98 1.98 1.98 1.98 1.98 1.98 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.45 30.18 30.18 41.28 30.18 41.28 30.18 41.28 49.28 49.28 49.28 49.28 49.28 49.28 49.28 49.28 13.89 14.28 19.05 14.28 19.05 14.28 19.05 19.05 19.05 19.05 20.64 20.64 22.22 22.22 22.22 15.87 17.46 17.46 19.05 19.05 22.22 22.22 25.40 28.57 31.75 34.92 41.27 48.26 53.97 58.25 18.25 20.64 20.64 23.02 23.02 24.61 24.61 26.99 29.37 31.75 34.92 39.69 44.45 49.21 55.58 25.68 28.04 28.04 30.43 30.43 32.82 32.82 35.08 38.38 41.55 44.73 51.08 57.15 63.78 69.85 Straight Plug MS-3106 Q MS-4106 V A All dimensions are in mm Connector Size A Thread in inches Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 63.50 5/8-24 NEF 11/16-24NEF 11/16-24NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-20 UN Note - Both versions, straight and diamond knurling available on coupling ring. For details, contact factory. 20 S hell style Q max Right angle plug MS-3108 MS-4108 A THREAD V All dimensions are in mm Connector Size A Thread in inches Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 NS 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 29/32-18 NS 2 1/16-20 UNS 40 2 1/2-16 UN 63.50 2 5/16-16 UN Note - Both versions, straight and diamond knurling available on coupling ring. For details, contact factory. Other Accessories Dummy receptacle A B MS-3105 OC E OG F MAX D All dimensions are in mm Part number (see note) A B C 3.05 D Thread in inches 5/8-24 MS-3105-10S 25.4 18.26 MS-3105-12S 27.79 E F G 14.27 3.96 8.20 20.62 3.05 3/4-20 14.27 3.96 11.43 max. MS-3105-12 27.79 20.62 3.05 3/4-20 19.05 3.96 11.43 MS-3105-14S 30.17 23.01 3.05 7/8-20 14.27 3.96 13.36 MS-3105-14 30.17 23.01 3.05 7/8-20 19.05 3.96 13.36 MS-3105-16S 32.54 24.61 3.05 1-20 14.27 3.96 16.41 MS-3105-16 32.54 24.61 3.05 1-20 19.05 3.96 16.41 MS-3105-18 34.92 26.97 3.05 1 1/8-18 19.05 5.16 18.03 MS-3105-20 38.10 29.36 3.05 1 1/4-18 19.05 5.16 23.54 MS-3105-22 41.27 31.75 3.05 1 3/8-18 19.05 5.16 25.93 MS-3105-24 44.45 34.92 3.73 1 1/2-18 20.62 5.16 29.21 MS-3105-28 50.8 39.67 3.73 1 3/4-18 20.62 5.16 34.67 MS-3105-36 63.5 49.22 4.39 2 1/4-16 22.2 9.11 46.56 Note: The dash number also indicates shell size. 21 P rotective Cap For MS Series MS-25043 For receptacles Has internal threads and is used on all receptacles. Gasket is provided in the dust cap forming a watertight seal. D C MAX A B MAX E All dimensions are in mm MS Part number Shell size A Thread in inches B C D E MS 25043-10D MS 25043-12D MS 25043-14D MS 25043-16D MS 25043-18D MS 25043-20D MS 25043-22D MS 25043-24D MS 25043-28D MS 25043-32D MS 25043-36D MS 25043-40D MS 10S-1-SL MS 12-12S MS 14-14S MS 16-16S MS 18 MS 20 MS 22 MS 24 MS 28 MS 32 MS 36 MS 40 5/8-24 3/4- 20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 1/2-18 1 3/4-18 2-18 2 1/4-18 2 1/2-16 11.11 11.11 11.11 11.11 11.11 11.11 11.11 11.11 12.7 12.7 12.7 12.7 20.7 25.4 28.6 30.2 34.1 37.3 40.4 43.6 50 56.3 62.7 69 3.6 3.6 3.6 3.6 3.6 4.4 4.4 4.4 4.4 4.8 4.8 4.8 102 115 115 115 115 127 127 140 197 197 197 197 Notes : 1. 2. 3. 4. For protective caps with nylon cord, contact factory. Standard - Plating is Cad. For alternative finishes, contact factory. Standard - straight knurling. For diamond knurling on caps, contact factory. Please add 07 suffix for bigger end link. Other Accessories Protective cap for MS series MS-25042 For plugs Has external threads and is used on all plugs where a coupling ring is provided. A D C MAX B MAX E All dimensions are in mm MS Part number Shell size A Thread in inches B C D E MS 25042-10D MS 25042-12D MS 25042-14D MS 25042-16D MS 25042-18D MS 25042-20D MS 25042-22D MS 25042-24D MS 25042-28D MS 25042-32D MS 25042-36D MS 25042-40D MS 10S-1-SL MS 12-12S MS 14-14S MS 16-16S MS 18 MS 20 MS 22 MS 24 MS 28 MS 32 MS 36 MS 40 5/8-24 3/4- 20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 1/2-18 1 3/4-18 2-18 2 1/4-18 2 1/2-16 16.67 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 17.4 20.6 23.7 26.9 30 33 36.4 39.6 46 52 58.7 65 4 4 4 4 4 4.8 4.8 4.8 4.8 5.6 5.6 5.6 102 115 115 115 115 127 127 140 197 197 197 197 22 MIL -C-5015 97B Series Bayonet Version connector S hell style Wall mounting receptacle 100 V T THD K M R S L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 'R' `S' +0.20 `L' MAX PG THD 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.00 50.80 57.00 63.50 27.60 27.60 27.60 27.60 33.80 33.80 33.80 33.80 35.70 35.70 37.30 37.30 5/8"-24 UNEF 5/8"-24 UNEF 3/4"-24 UNEF 7/8"-24 UNEF 7/8"-24 UNEF 1"-20 UNEF 1 1/8"-18 UNEF 1 1/8"-18 UNEF 1 3/8"-18 UNEF 1 5/8"-18 UNEF 1 7/8"-16 UN 2 1/16"-16 UN Cable connecting receptacle 101 T THD AT 0/ S 0/ A 45 0 A/ -L O K M L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `Q' +0.20 `S' +0.20 `L' MAX T -2A THD 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.70 41.30 47.60 54.00 60.60 25.00 27.60 29.60 32.10 32.10 34.60 37.60 40.90 44.40 50.70 56.90 63.40 27.60 27.60 27.60 27.60 33.80 33.80 33.80 33.80 35.70 35.70 37.30 37.30 5/8"-24 UNEF 5/8"-24 UNEF 3/4"-24 UNEF 7/8"-24 UNEF 7/8"-24 UNEF 1"-20 UNEF 1 1/8"-18 UNEF 1 1/4"-18 UNEF 1 3/8"-18 UNEF 1 5/8"-18 UNEF 1 7/8"-16 UN 2 1/16"-16 UN Box mounting receptacle 0/ V 102 R S M K L 23 SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +0.20 - 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 24.70 27.60 24.70 24.70 33.80 33.80 33.80 33.80 35.70 35.70 37.30 37.30 Rear mounting Receptacle 0/ A 103 M R S K L SHELL SIZE 'A' +0.0 -0.15 'M' 'K' +0.41 +-0.20 -0.0 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 'R' +0.20 - 'S' +0.20 - 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 27.60 27.60 27.60 27.60 33.80 33.80 33.80 33.80 35.70 35.70 37.30 37.30 Plug connector 106 T THD `L' `A' AFTER KNURLING SHELL SIZE 'A' MAX. 'L' MAX 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 56.00 56.00 54.00 56.00 67.00 74.00 75.00 78.00 78.00 82.00 82.00 90.00 'T' - 2A THD 5/8"-24 UNEF 5/8"-24 UNEF 3/4"-24 UNEF 7/8"-24 UNEF 7/8"-24 UNEF 1"-20 UNEF 1 1/8"-18 UNEF 1 1/4"-18 UNEF 1 3/8"-18 UNEF 1 5/8"-18 UNEF 1 7/8"-18 UN 2 1/16"-16 UN Jam Nut Receptacles 107 C H 0/ B D A F L E D SHELL SIZE A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 24 WALL THICKNESS MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 27.70 30.00 30.00 35.30 37.70 37.70 37.70 37.70 35.20 35.20 35.20 S hell style Box mount Receptacle with PC Tail contacts L 9.00 o A 7.00 o1.5 for size 12 o 0.76 for size 16 R M K Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' `S' +0.20 `L' +0.20 - 10SL 12S 14S 16S 6 18 20 22 24 28 32 36 40 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 65.51 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 55.50 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 69.90 24.70 24.70 24.70 24.70 33.80 33.80 33.80 33.80 33.80 33.80 33.80 33.80 33.80 Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' `S' +0.20 `L' +0.20 - 10SL 12S 14S 16S 6 18 20 22 24 28 32 36 40 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 65.51 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 55.50 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 69.90 24.70 24.70 24.70 24.70 33.80 33.80 33.80 33.80 33.80 33.80 33.80 33.80 33.80 S Rear Mount Receptacle with PC Tail contacts L 9.00 o A 7.00 o 1.5 for size 12 o 0.76 for size 16 M R K S L2 D 6.00 max 1.50 (#12) L3 C 0.76 (#16) Jam Nut receptacles with PC Tail contacts L4 B H G F E A 7.00 L1 Shell Size `A' -2A Threads 10SL 14S 16S 16 18 20 22 24 28 32 36 40 7/8"-2OUNEF 1" 1/8-18UNEF 1" 1/4-18UNEF 1" 1/4-18UNEF 1" 3/8-18UNEF 1" 1/2-18UNEF 1" 5/8-18UNEF 1" 3/4-18UNS 2"-18UNS 2" 1/4-16UN 2" 1/2-16UN 2" 3/4-16 UN `B' +0.00 - 0.15 18.20 24.60 27.40 27.40 30.80 34.20 37.40 40.90 46.70 53.40 59.60 65.50 Panel Cut Out 9.00 `C' `D' `E' F 5.00 6.00 6.00 6.00 7.00 7.00 7.00 7.00 7.00 7.00 8.00 8.00 2.50 2.50 2.50 2.50 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 31.80 38.10 41.20 41.20 45.00 49.20 52.40 55.20 62.20 68.20 75.20 82.20 35.00 41.30 44.40 44.40 48.20 52.40 55.50 59.00 66.00 72.00 80.00 87.00 25 G 31.50 37.90 41.00 41.00 44.80 49.00 52.20 55.00 62.00 68.00 75.00 82.00 H 22.70 28.80 32.00 32.00 35.10 38.20 42.00 44.70 51.10 57.40 63.80 70.20 L1 29.20 29.20 29.20 37.70 40.00 40.00 40.00 40.00 40.00 40.00 40.00 40.00 L2 13.50 13.50 13.50 13.50 15.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 L3 12.50 12.50 12.50 21.00 21.00 21.00 21.00 21.00 21.00 21.00 21.00 21.00 L4 20.90 27.20 30.40 30.40 33.60 36.80 39.90 43.10 49.20 55.70 62.00 68.50 S hell style Wall Mount Receptacle with A type Solid B/S A TTHD 100A M R S K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' `S' +0.20 `L' MAX `T' THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 45.00 45.00 48.00 48.00 55.00 60.00 65.00 65.00 68.00 68.00 70.00 70.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS Wall Mount Receptacle with A type solid B/S & Environmental sealing Grommet 100AG Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' `S' +0.20 `L' MAX `T' THD 10SL 12S 14S 16S 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 68.60 68.60 68.60 68.60 75.00 75.00 75.00 75.00 77.00 77.00 80.00 80.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS Wall Mount Receptacle with F type Strain Relief B/S & Environmental sealing Grommet A 100F M R S K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 60.00 60.00 61.00 61.00 68.00 72.00 74.00 74.00 78.00 78.00 82.00 82.00 Wall Mount Receptacle with R type B/S & Environmental sealing Grommet A 100R R S K M L 26 SHELL SIZE 'A' +0.0 -0.15 'K' +-0.20 'M' +0.41 -0.0 'R' 'S' +-0.20 'L' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 47.00 47.00 47.00 48.00 54.40 56.40 56.40 56.40 57.40 57.40 58.10 58.10 S hell style Wall Mount Receptacle with G type B/S for heatshrinkable & Environmental sealing Grommet A 100G M R K L S SHELL SIZE 'A' +0.0 -0.15 'K' +-0.20 'M' +0.41 -0.0 'R' 'S' +-0.20 'L' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 52.50 52.50 54.40 54.40 61.00 62.00 62.00 65.00 65.00 66.00 71.00 75.00 Wall Mount Receptacle with PG threaded type B/S suitable for PG Glands A PG THD 100PG R S M K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 'R' `S' +0.20 `L' MAX PG THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 56.00 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 7, 9, 11 7, 9, 11 11, 13.5 9, 11, 16 9, 11, 16 9, 11, 16, 21 11, 16, 21 13.5, 16, 21 13.5, 16, 21, 29 16, 21, 29 21, 29 21, 29, 36 Wall Mount Receptacle with EGM B/S for shielded cable & PHM B/S Unshielded cable with sealing rubber bush A 100EGM/PHM R S M K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 95.60 95.60 95.60 95.60 102.00 102.00 102.00 102.00 104.00 104.00 106.00 106.00 'R' 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 57.00 57.00 59.00 59.00 66.00 66.00 66.00 66.00 68.00 68.00 70.00 70.00 Wall Mount Receptacle with SQ type Shielded B/S & Environmental sealing Grommet & Heat shrinkable option A 100SQ R S M K L 27 SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 S hell style Wall Mount Receptacle with Metric threaded type B/S suitable for Metric Glands 100M Shell Size A M Thread 10SL 14s 16s 6 18 20 22 24 28 32 36 M R S K L `M' `A' `K' +0.0 -0.15 +0.20 +0.41 - 0.0 'R' `S' +0.20 'L' MAX. M THD 2.79 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 M12X1.5 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 18.21 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 Wall Mount Receptacle with 900 B/S & Environmental sealing Grommet P A 100RT M R S K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +-0.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 'L' 'P' MAX. MAX. 40.50 40.50 42.00 45.00 52.00 53.00 58.00 58.00 63.00 63.00 69.00 72.30 21.50 21.50 23.00 24.60 24.60 27.00 29.00 31.00 34.00 36.00 44.00 46.00 Cable connecting Receptacle with A type Solid B/S A/ Q FL AT . A T THD 45 S 101A M K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `Q' `S' +0.20 `L' MAX `T' THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.00 27.60 29.60 32.10 32.10 34.60 37.60 40.90 44.40 50.70 56.90 63.40 45.00 45.00 48.00 48.00 55.00 60.00 65.00 65.00 68.00 68.00 70.00 70.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS Cable connecting Receptacle with F type Strain Relief B/S & Environmental sealing Grommet 'A' SHELL +0.0 SIZE -0.15 45 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 A/ FL Q AT . A S 101F M K L 28 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'K' +-0.20 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 'M' +0.41 -0.0 'Q' +-0.20 'S' +-0.20 'L' MAX. 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.0 27.60 29.60 32.10 32.10 34.60 37.60 40.90 44.40 50.70 56.90 63.40 60.00 60.00 61.00 61.00 68.00 72.00 74.00 74.00 78.00 78.00 82.00 82.00 S hell style Cable connecting Receptacle with R type B/S & Environmental sealing Grommet 101R A/ Q FL AT . S A 45 M K L SHELL SIZE 'A' +0.0 -0.15 'K' +-0.20 'M' +0.41 -0.0 `Q' +0.20 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.00 60.00 'S' +-0.20 'L' MAX. 25.00 27.60 29.60 32.10 32.10 34.60 37.60 40.90 44.40 50.70 56.90 63.40 47.00 47.00 47.00 48.00 54.40 56.40 56.40 56.40 57.40 57.40 58.10 58.10 Cable connecting Receptacle with G type B/S for heatshrinkable & Environmental sealing Grommet 101G A/ FL Q AT . A S 45 0 M K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'Q' +-0.20 'S' +-0.20 'L' MAX. 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 52.50 52.50 54.40 54.40 61.00 62.00 63.00 65.00 65.00 66.00 71.00 75.00 Cable connecting Receptacle with A type Solid B/S & Environmental sealing Grommet Q FL AT . A T THD 45 0 S 101AG A/ M K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 'Q' +-0.20 `S' +0.20 `L' MAX `T' THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 68.60 68.60 68.60 68.60 75.00 75.00 75.00 75.00 77.00 77.00 80.00 80.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS Cable connecting Receptacle with PG threaded type B/S suitable for PG Glands 101PG A/ PG THD FL Q AT . A S 45 0 K M L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 'Q' +-0.20 `S' +0.20 `L' MAX PG THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 56.00 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 7, 9, 11 7, 9, 11 11, 13.5 9, 11, 16 9, 11, 16 9, 11, 16, 21 11, 16, 21 13.5, 16, 21 13.5, 16, 21, 29 16, 21, 29 21, 29 21, 29, 36 29 S hell style Cable connecting Receptacle with EGM B/S for shielded cable & PHM B/S Unshielded cable with sealing rubber bush 101EGM/PHM A/ Q FL AT . A S 45 M K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'Q' +-0.20 'S' +-0.20 'L' MAX. 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 95.60 95.60 95.60 95.60 102.00 102.00 102.00 102.00 104.00 104.00 106.00 106.00 Cable connecting Receptacle with SQ type Shielded B/S & Environmental sealing Grommet & Heat Shrinkable option 101SQ A/ FL Q AT . S A 45 K M L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'Q' +-0.20 'S' +-0.20 'L' MAX. 20.60 23.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 57.00 57.00 59.00 59.00 66.00 66.00 66.00 66.00 68.00 68.00 70.00 70.00 Cable connecting Receptacle with Metric threaded type B/S suitable for Metric Glands 101M Shell Size A/ Q FL AT . M THD A S 45 M K 10SL 14s 16s 6 18 20 22 24 28 32 36 `M' 'Q' `A' `K' `S' +0.0 -0.15 +0.20 +0.41 - 0.0 +-0.20 +0.20 18.21 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 20.60 25.40 28.60 28.60 31.70 34.90 31.80 41.30 47.60 54.0 60.60 25.40 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 'L' MAX. M THD 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 M12X1.5 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 L Rear wall Mount Receptacle with A type Solid B/S A T THD 103A R S M K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' +0.10 `S' +0.20 `T' THD `L' MAX 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS 45.00 45.00 48.00 48.00 55.00 60.00 65.00 65.00 68.00 68.00 70.00 70.00 30 S hell style Rear wall Mount Receptacle with F type Strain Relief B/S & Environmental sealing Grommet A 103F M R S K L SHELL SIZE 'A' +0.0 -0.15 'K' +-0.20 'M' +0.41 -0.0 'R' +-0.10 'S' +-0.20 'T' THD. 'L' MAX 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 5/8-24 UNEF 5/8 24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 60.00 60.00 61.00 61.00 68.00 72.00 74.00 74.00 78.00 78.00 82.00 82.00 Rear wall Mount Receptacle with R type B/S & Environmental sealing Grommet A 103R M R S K L SHELL SIZE 'A' +0.0 -0.15 'K' +-0.20 'M' +0.41 -0.0 'R' 'S' +-0.20 'L' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 47.00 47.00 47.00 48.00 54.40 56.40 56.40 56.40 57.40 57.40 58.10 58.10 Rear wall Mount Receptacle with G type B/S for heatshrinkable & Environmental sealing Grommet A 103G M R S K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 'R' 'S' +-0.10 +-0.20 'L' MAX. 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 52.50 52.50 54.40 54.40 61.00 62.00 63.00 65.00 65.00 66.00 71.00 75.00 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 Rear wall Mount Receptacle with A type Solid B/S & Environmental sealing Grommet A T THD 103AG R S M K L Shell Size `A' +0.0 -0.15 `K' +0.20 `M' +0.41 - 0.0 `R' +0.10 `S' +0.20 `T' THD `L' MAX 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS 68.60 68.60 68.60 68.60 75.00 75.00 75.00 75.00 77.00 77.00 80.00 80.00 31 S hell style Rear wall Mount Receptacle with PG threaded type B/S suitable for PG Glands A PG THD 103PG M R S K L Shell Size `A' +0.0 -0.15 `K' +0.20 'M' +0.41 -0.0 'R' +-0.10 `S' +0.20 `L' MAX PG THD 10SL 12s 14s 16s 6 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 56.00 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 7, 9, 11 7, 9, 11 11, 13.5 9, 11, 16 9, 11, 16 9, 11, 16, 21 11, 16, 21 13.5, 16, 21 13.5, 16, 21, 29 16, 21, 29 21, 29 21, 29, 36 Rear wall Mount Receptacle with EGM B/S for shielded cable & PHM B/S Unshielded cable with sealing rubber bush A 103 EGM/PHM R S M K L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 95.60 95.60 95.60 95.60 102.00 102.00 102.00 102.00 104.00 104.00 106.00 106.00 Rear wall Mount Receptacle with SQ type Shielded B/S & Environmental sealing Grommet & Heat Shrinkable Option 'A' 'M' SHELL SIZE 103SQ A 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 R S M K L 'K' +0.41 +-0.20 -0.0 +0.0 -0.15 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 'R' +-0.10 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 57.00 57.00 59.00 59.00 66.00 66.00 66.00 66.00 68.00 68.00 70.00 70.00 Rear wall Mount Receptacle with Metric threaded type B/S suitable for Metric Glands 103M Shell Size M THD A R S 10SL 14s 16s 6 18 20 22 24 28 32 36 M K L 32 `M' `A' `K' +0.0 -0.15 +0.20 +0.41 - 0.0 'R' `S' +0.20 'L' MAX. M THD 2.79 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 18.20 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 M12X1.5 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 18.21 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 18.20 18.20 18.20 23.05 23.05 23.05 23.05 23.05 24.05 24.05 24.05 S hell style Rear wall Mount Receptacle with 900 B/S & Environmental sealing Grommet P A 103RT R S K M L SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' 'S' +-0.20 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 'L' 'P' MAX. MAX. 40.50 40.50 42.00 45.00 52.00 53.00 58.00 58.00 63.00 63.00 69.00 72.30 Straight Plug with A type solid B/S TTHD 106A `A' AFTER KNURLING. L SHELL SIZE 'A' MAX. 'L' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.39 46.10 46.60 53.40 60.10 36.30 44.00 44.00 46.00 46.00 46.00 55.00 62.00 65.00 65.00 68.00 70.00 70.00 'T' THD 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS Rear wall Mount Receptacle with SQ type Shielded B/S & Environmental sealing Grommet 106F `A' AFTER KNURLING. L SHELL SIZE 'A' MAX. 'L' MAX 'T' THD. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 60.00 60.00 60.00 60.00 68.00 72.00 74.00 74.00 78.00 78.00 82.00 82.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS Straight Plug with R type B/S & Environmental sealing Grommet SHELL 'A' SIZE MAX. 106R `A' AFTER KNURLING 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 L 33 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 36.30 'L' MAX. 47.00 47.00 47.00 47.00 55.40 57.40 57.40 57.40 57.40 57.40 58.10 58.10 21.50 21.50 23.00 24.60 24.60 27.00 29.00 31.00 34.00 36.00 44.00 46.00 LS hell styleQualified Part Numbers ist Of Straight Plug with G type B/S for Heat Shrinkable & Environmental sealing Grommet SHELL SIZE 106G `A' AFTER KNURLING 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 L 'A' MAX 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 'L' MAX 53.00 53.00 53.00 53.00 61.00 62.00 63.00 65.00 65.00 68.00 71.00 75.00 Straight Plug with A type Solid B/S & Environmental sealing Grommet T THD 106AG `A' AFTER KNURLING L SHELL SIZE 'A' MAX. 'L' MAX. `T' THD 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 68.60 68.60 67.00 67.00 76.00 76.00 76.00 76.00 78.00 78.00 80.00 80.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18 UNS SHELL SIZE 'A' MAX. `L' MAX PG THD 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 56.00 56.00 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 7, 9, 11 7, 9, 11 11, 13.5 9, 11, 16 9, 11, 16 9, 11, 16, 21 11, 16, 21 13.5, 16, 21 13.5, 16, 21, 29 16, 21, 29 21, 29 21, 29, 36 Straight Plug with PG threaded type B/S suitable for PG Glands PG THD 106PG `A' AFTER KNURLING L SHELL SIZE 106 EGM/PHM 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 `A' AFTER KNURLING 34 'A' MAX 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 'L' MAX 53.00 53.00 53.00 53.00 61.00 62.00 63.00 65.00 65.00 68.00 71.00 75.00 S hell style Straight Plug with SQ type Shielded B/S & Environmental sealing Grommet & Heat Shrinkable option SHELL 'A' SIZE MAX. 106SQ `A' AFTER KNURLING 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 L 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 'L' MAX. 56.60 56.60 57.00 57.00 66.00 66.00 66.00 66.00 68.00 66.00 70.00 70.00 Straight Plug with Metric threaded type B/S suitable for Metric Glands Shell Size 106M 'A' MAX. 'L' MAX. M THD M THD 10SL 22.80 56.00 M12X1.5 `A' AFTER KNURLING L 14s 16s 6 18 20 22 24 28 32 36 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 56.00 58.00 66.00 74.00 74.00 77.00 77.00 78.00 78.00 90.00 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 Jam Nut Receptacle with A type Solid B/S 107TA C A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 E H B T THD D A L F D SHELL SIZE WALL THICKNESS MIN MAX 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 52.00 58.00 58.00 68.00 76.00 80.00 80.00 82.00 84.00 85.00 85.00 Jam Nut Receptacle with F type Strain Relief B/S with Environmental sealing Grommet 107TF C H E B D F A L D SHELL SIZE A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 35 WALL THICKNESS MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 69.00 72.00 72.00 83.00 87.00 89.00 89.00 92.00 95.00 97.00 97.00 S hell style Jam Nut Receptacle with R type B/S with Environmental sealing Grommet 107TR C E H A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 B D A L F D SHELL SIZE E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 56.00 59.00 70.00 72.00 72.00 72.00 72.00 72.00 74.00 74.00 74.00 WALL THICKNESS MIN MAX 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 Jam Nut Receptacle with G type B/S for Heat shrinkable & Environmental sealing Grommet 107G H C E 0/B D A L F Shell Size `A' -2A Threads 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8"-2OUNEF 1" 1/8-18UNEF 1" 1/4-18UNEF 1" 1/4-18UNEF 1" 3/8-18UNEF 1" 1/2-18UNEF 1" 5/8-18UNEF 1" 3/4-18UNS 2"-18UNS 2" 1/4-16UN 2" 1/2-16UN 18.20 24.60 27.40 27.40 30.80 34.20 37.40 40.90 46.70 53.40 59.60 D Wall Thickness MIN. MAX. `C' `B' +0.00 - 0.15 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 E F +0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 61.00 66.00 66.00 76.00 78.00 79.00 81.00 79.00 82.00 85.00 90.00 Jam Nut Receptacle with AG type B/S for heat shrinkable & Environmental sealing Grommet 107AG C E H A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 B T THD D A L F D SHELL SIZE E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 77.00 80.00 80.00 90.00 92.00 92.00 92.00 92.00 94.00 94.00 94.00 WALL THICKNESS MIN MAX 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 Jam Nut Receptacle with PG threaded type B/S suitable for PG Glands 107TPG C E H B PG THD D A F L SHELL SIZE A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 36 D WALL THICKNESS MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 E F +-0.25 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 H L 27.00 64.60 33.00 68.00 38.10 70.00 38.10 81.00 39.70 89.00 44.00 90.00 46.00 93.00 50.80 91.00 55.00 95.00 62.00 94.00 71.00 105.00 PG THD 7, 9,11 11,13.5 9,11,16 9,11,16 9,11,16,21 11,16,21 13.5,16,21 13.5,16,21 16,21,29 21,29 21,29,36 S hell style Jam Nut Receptacle with EGM B/S for shielded cable & PHM B/S Unshielded cable with sealing rubber bush 107TEGM/PHM C E B D A L D SHELL SIZE A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 E F +-0.25 H L 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 104.20 107.00 107.00 107.00 118.00 118.00 118.00 118.00 120.00 120.00 120.00 WALL THICKNESS MIN MAX 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 Jam Nut Receptacle with SQ type Shielded B/S & Environmental sealing Grommet & Heat Shrinkable Option D B A F SHELL +0.0 C E H WALL THICKNESS 107TSQ C -2A THREADS +-0.25 SIZE E -0.15 H D A 10SL 14S 16S 16 18 20 22 24 28 32 36 L F 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 L 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 66.00 70.20 70.20 80.00 81.00 81.00 82.00 82.00 84.00 84.00 84.00 Jam Nut Receptacle with Metric threaded type B/S suitable for Metric Glands 107TM A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 C H E S M THD D A F L D SHELL SIZE E F +-0.25 H L M THD 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 66.00 70.20 70.20 80.00 81.00 81.00 82.00 82.00 84.00 84.00 84.00 M12X1.5 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 WALL THICKNESS MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 Jam Nut Receptacle with 900 B/S & Environmental sealing Grommet 107TRT C H E P B D F A L D SHELL SIZE A -2A THREADS B +0.0 -0.15 C 10SL 14S 16S 16 18 20 22 24 28 32 36 7/8" - 20 UNEF 1" 1/8-18 UNEF 1' 1/4-18 UNEF 1" 1/4- 18 UNEF 1" 3/8- 18 UNEF 1" 1/2- 18 UNEF 1" 5/8- 18 UNEF 1" 3/4- 18 UNS 2" - 18 UNS 2" 1/4- 16 UN 2" 1/2- 16 UN 18.20 24.60 27.40 27.40 30..80 34.20 37.40 40.90 46.70 53.40 59.60 24.50 26.80 26.80 32.10 33.70 33.70 33.70 33.70 35.20 35.20 35.20 37 WALL THICKNESS MIN MAX 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 2.40 5.20 7.50 7.50 7.50 9.00 9.00 9.10 9.10 8.50 6.50 8.30 E F +-0.25 H L 'P' MAX. 4.00 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 5.60 5.60 31.80 41.30 44.40 44.40 47.60 50.80 54.20 57.20 63.50 69.80 76.20 27.00 33.00 38.10 38.10 39.70 44.00 46.00 50.80 55.00 62.00 71.00 49.00 54.00 57.00 66.00 69.00 75.00 75.00 77.00 80.00 84.00 87.00 21.50 23.00 24.60 24.60 27.00 29.00 31.00 34.00 36.00 44.00 46.00 S hell style 900 Plug Connector 108A=Supplied without grommet 108R=Supplied with grommet P A L T THD SHELL 'A' SIZE MAX. 'L' MAX. 'P' MAX. 'T' THD 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 41.00 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 74.00 21.50 21.50 23.00 24.60 24.60 27.00 29.00 31.00 34.00 36.00 44.00 46.00 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 900 Plug connector with G type B/S for Heat Shrinkable & Environmental sealing Grommet 108G P Q L SHELL SIZE 'A' MAX 'L' MAX `P' MAX 10SL 12S 14S 16S 16 18 20 22 24 28 32 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 41.00 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 76.00 46.00 46.20 50.00 52.00 52.00 55.00 58.00 62.00 63.00 65.00 76.00 0 90 Plug connector with Strain Relief B/S & Environmental sealing Grommet 108E P Q L SHELL SIZE 'A' MAX. 'L' MAX. 'P' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.39 46.10 46.60 53.40 60.10 36.30 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 70.00 74.00 38.00 40.00 41.00 45.00 45.00 48.00 50.00 52.00 56.00 58.00 68.00 70.00 0 90 Plug connector with PG threaded type B/S suitable for PG Glands L P Q 108PG PG THD 38 SHELL SIZE 'A' MAX. 'L' MAX. 'P' MAX. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 41.00 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 74.00 7, 9, 11 50.00 7, 9, 11 50.00 11, 13.5 52.00 9, 11, 16 55.00 9, 11, 16 57.00 67.00 9, 11, 16, 21 11, 16, 21 69.00 13.5, 16, 21 74.00 75.00 13.5, 16, 21, 29 16, 21, 29 78.00 21, 29 85.00 21, 29, 36 98.00 PG THD S hell style 900 Plug connector with EGM B/S for shielded cable & PHM B/S Unshielded cable with sealing rubber bush 108EGM/PHM SHELL 'A' SIZE MAX. L P Q 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 'L' MAX. 'P' MAX. 41.00 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 74.00 91.00 91.00 91.00 93.00 93.00 95.00 97.00 99.00 102.00 103.00 111.00 113.00 900 Plug connector with SQ type Shielded B/S & Environmental sealing Grommet & Heat Shrinkable Option L 108SQ SHELL 'A' SIZE MAX. P Q 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 22.80 25.60 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 'L' MAX. 'P' MAX. 41.00 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 74.00 49.00 51.00 55.00 56.00 56.00 59.00 60.00 63.00 66.00 67.00 75.00 77.00 900 Plug connector with Metric threaded type B/S suitable for Metric Glands P Q 108M L M THD 39 Shell 'A' Size MAX. `L' MAX. 'P' MAX. M THD 10SL 14s 16s 6 18 20 22 24 28 32 36 41.00 41.00 43.00 53.00 55.00 60.00 60.00 64.00 64.00 70.00 74.00 49.50 49.50 49.50 52.00 63.00 65.00 67.00 73.00 75.00 85.00 98.00 M12X1.5 M16X1.5 M16X1.5 M16X1.5 M20X1.5 M25X1.5 M25X1.5 M32X1.5 M32X1.5 M36X1.5 M40X1.5 22.80 29.20 32.00 32.00 36.50 39.90 43.10 46.60 53.40 60.10 66.30 S hell style Panel mounting plug connector 97B - 3164 97B-4164 L3 e LP L4 L4 d2 e l1 l3 +- 0.2 l4 +- 0.3 2.8 3.2 3.2 3.2 4 4 4 4 4 4 4 4 25.4 30 32.5 32.5 35 38 41 44.5 50.8 57 63.5 69.9 L1 All dimensions are in mm Shell Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 d1 d2 Max H13 22.8 29.2 32 32 36.5 39.9 43.1 46.6 53.4 60.1 66.3 72.5 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.7 3.7 4.3 4.3 4.3 e +- 0.1 18.2 23 24.6 24.6 27 29.4 31.8 34.9 39.7 44.5 49.2 55.5 ~ 28.1 28.1 28.1 37.6 38.6 38.6 38.6 41 41.8 45 45 45 40 B ack accessory Solid backshell without grommet and sleeve Class A Q L V A All dimensions are in mm A Thread in inches L max for MS L max for 97B Q max V Thread in inches 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 32.54 37.31 46.83 36.51 46.83 37.70 48.02 50.80 53.97 53.97 57.15 57.15 59.0 60.32 71.80 37.60 ----37.64 --38.83 48.00 51.58 54.75 54.75 57.94 57.94 59.78 61.13 80.00 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 63.50 5/8-24 UNEF 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4 - 16 UN Connector Size 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 2 5/16-16 UN Solid Backshell With Grommet & Sleeve Class R All dimensions are in mm Connector Size 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 Q L A A Thread class 2B in inches 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN For Plug type L max for MS 47 47 55 47 55 47 55 57 57 57 57 57 58.25 58.25 58.25 For Receptacle L max for 97B 48 ----48 --48 56 57 57 57 57 57 60 60 60 Note - Both versions, straight and diamond knurling available on back accessories. For details, contact factory. 41 Q max 21.50 20.35 20.35 23.40 23.40 26.71 26.71 29.50 35.70 35.85 44.40 45.08 52.36 56.81 64.50 B ack accessory Back Accessories Strain relief backshell with grommet and sleeve L N Class E and F A All dimensions are in mm A Thread class 2B in inches L max for MS L max for 97B N max 5/8-24 NEF 11/16-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 54.07 54.07 55.90 55.90 64.41 65.94 67.41 67.41 73.28 73.28 74.75 74.75 86.0 59.10 --61.34 62.86 21.97 21.97 25.15 28.45 28.45 30.76 37.29 37.29 44.45 44.45 52.22 57.15 67.10 Connector Size 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 40 2 5/16-16 UN 71.10 72.55 72.55 76.82 77.82 77.64 125.0 Right Angle Backshell With Or Without Grommet L L1 Q Class A, F & R A V All dimensions are in mm Connector Size A Thread class 2B in inches L max for MS L max for 97B L1 max Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-26 UN 37.60 37.80 47.30 39.40 48.90 42.60 52.10 53.70 58.80 58.80 63.60 63.60 69.60 72.80 76.00 45.00 ----47.00 --48.00 57.00 58.00 61.00 61.00 66.00 66.00 72.00 75.00 78.00 25.00 25.00 25.00 27.00 27.00 28.00 28.00 31.00 34.00 34.00 37.00 39.00 45.00 48.00 55.00 22.22 25.40 25.40 28.57 28.57 31.75 31.75 34.13 37.30 40.48 43.66 50.00 56.50 62.71 62.71 5/8-24 UNEF 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4 -16 UN Note - Both versions, straight and diamond knurling available on back accessories. For details, contact factory. 42 B ack accessory Heat Shrink Boot adaptor (G) B A C 3.50+0.20 L B L Max. C- THD 20.30 30.00 5/8-24 NEF 22.30 27.00 3/4-20 UNEF 13.50 24.80 29.50 7/8-20 UNEF 14.60 18.70 20.80 24.60 27.00 33.30 38.50 48.20 28.50 Shell size A Min. 10SL 7.70 8.20 10.60 12S 14S 16S 16 18 20 22 24 28 32 36 40 1-20 UNEF 1 1/8-18 NEF 1 1/4-18 UNEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16 UN 2 1/16-16 UN 2 5/16-16 UN 33.50 34.50 35.10 41.00 44.80 51.50 56.00 62.00 35.70 34.00 34.10 34.20 34.20 36.60 Back Accessories Cable clamp MS-3057 Use MS-3420 sleeves B C A All dimensions are in mm Part number Shell size Max OD of cable A B C Thread in inches MS-3057-4A 10SL, 12S 5.59 20.90 21.39 7.94 5/8-24 MS-3057-6A 14, 14S 7.92 21.59 25.27 11.11 3/4-20 MS-3057-8A 16, 16S 11.10 23.37 28.45 14.29 7/8-20 23.37 30.89 15.87 1-20 19.50 1 3/16-18 MS-3057-10A 18 14.27 MS-3057-12A 20,22 15.87 23.07 35.03 MS-3057-16A 24,28 19.05 25.78 42.75 23.81 1 7/16-18 MS-3057-20A 32 23.80 28.00 51.00 31.70 1 3/4-18 MS-3057-24A 36 31.75 29.36 57.02 34.92 2-18 43 B ack accessory `O' Ring G PG B A PG Adaptor L Shell size G Thread in inches 10SL 12S 14 16 18 20 22 24 28 36 5/8-24 11/16-24 3/4-20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 5/8-18 2 1/8-18 PG 9 A 30 B 21 PG 11 L 26 PG 13 PG 16 A B L A B L 23 25 30 35 23 25 26 26 30 30 37 40 23 23 30 PG 21 A B L 25 30 35 35 25 28 28 28 30 37 40 40 PG 29 A B L 35 35 38 45 35 35 35 37 40 40 40 45 PG 36 A B L A B L 40 45 57 40 45 44 40 45 55 57 57 55 Ordering Information MS - XX-PGYY Where XX- Shell Size YY-PG-Thread Size L EGM/PHM Backshell Accessories G EGM INNER METAL FERRULE `O' RING PLASTIC CDMB RUBBER BUSH D GLAND NUT EGM BACKSHELL Shell size 10SL 12SL 14 16 18 20 22 24 32 36 G Thread in inches 5/8"-24 11/16"-24 3/4"-20 7/8"-20 1"-20 1.1/8"-18 1.1/4"-18 1.3/8"-18 1.29/32"-18 2.1/6"-18 EGM/PHM 11 D 25.00 25.00 25.00 25.00 29.00 31.50 L 37.00 37.00 37.00 40.00 40.00 52.00 35.00 35.00 52.00 52.00 60.00 60.00 70.00 70.00 Note:- Rubber Bush supplied in Packing In case of PHM inner metal Furrele is not required/supplied EGM/PHM11 Can accept cable Min. 5.70 mm & Max. 10.85 mm EGM/PHM21 Can accept cable Min. 12.70 mm & Max. 17.85 mm 44 EGM/PHM 21 D 27.00 27.00 27.00 27.00 31.00 33.50 35.00 35.00 52.00 52.00 L 41.00 41.00 41.00 43.00 43.00 55.00 60.00 60.00 70.00 70.00 B ack accessory Neoprene Sleeve MS-3420 Rubber bushing. Protects wire bundles and unjacketed cables from possible damage by cable clamp. D F B A C E 45 0 All dimensions are in mm E Rad in inches Part number A MS-3420-3 3.30 5.33 9.50 73.02 0.79 F Rad in inches 0.79 MS-3420-4 5.59 7.67 12.70 69.85 0.79 0.79 MS-3420-6 7.92 10.84 15.59 66.67 0.79 1.59 1.59 B C D MS-3420-8 11.10 14.02 18.77 63.50 1.59 MS-3420-10 14.27 15.62 21.94 60.32 1.59 1.59 MS-3420-12 15.87 18.80 26.23 56.20 1.59 1.59 MS-3420-16 19.05 23.54 26.39 53.97 1.59 1.59 MS-3420-20 23.80 31.50 40.41 50.80 1.59 1.59 MS-3420-24 31.75 34.67 46.79 47.62 1.59 1.59 Plain Flat Gasket For MS and 97B flange mounted receptacles B A O C C A OD 4 HOLES T All dimensions are in mm Part number Shell size A max B C D MS-101000 MS-108686 MS-101001 MS-101002 MS-101003 MS-101004 MS-101005 MS-108687 MS-101006 MS-108688 MS-101007 MS-110831 10SL 12S & 12 14S & 14 16S & 16 18 20 22 24 28 32 36 40 18.26 20.62 23.01 24.61 27.00 29.36 31.75 34.90 39.70 44.45 49.22 55.77 15.90 19.05 22.20 25.40 28.57 31.75 34.90 38.10 44.45 50.80 55.57 61.92 25.40 27.80 30.15 32.50 34.90 38.10 41.20 44.45 50.80 57.15 63.50 69.85 4.35 4.35 4.35 4.35 5.15 5.15 5.15 5.15 5.15 5.55 5.55 5.55 45 T 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 P rotective cap for 97B 'B' 'D' 97B-25042 INK MARK A CONN. NO. & BATCH CODE AS PER BOM. All dimensions are in mm 'A' 'B' SHELL MAX. MAX. SIZE 10 SL 14 S 16 S 16 'D' + 0.60/-0 21.0 27.50 33.50 20 37.0 22 40.0 24 43.0 28 49.50 32 56.0 36 62.50 40 73.0 'E' MIN. 90.0 23.50 4.30 30.0 18 'E' + ONE LINK 'A' For Plugs 100.0 115.0 4.70 130.0 5.50 190.0 31.50 'B' Protective Cap For 97B Series 97B-25043 'D' INK MARK A CONN. NO. & BATCH CODE AS PER BOM. All dimensions are in mm SHELL SIZE 'A' MAX. 10 SL 23.0 14 S 30.0 16 S 16 'B' + 0.20 'D' + 0.60/-0 16.0 'E' MIN. 90.0 32.50 18 37.0 20 40.50 22 43.50 24 47.0 28 54.0 32 60.50 36 67.0 40 73.0 4.30 100.0 115.0 20.70 5.50 160.0 Note :- Please add 07 suffix for bigger end link. Applicable for Jam Nut 46 'E' + ONE LINK 'A' For Receptacle C rimp Contact Details Pin - Male Crimp Contact L CONTACT 'A' SIZE 97B - 106433 97B - 108295 97B - 109388 97B - 108386 97B - 108384 97B - 112067 B A D C CONTACT PART NO 16S 16 12 8 4 0 'B' 1.59 3.10 1.59 3.10 2.39 4.78 3.60 7.85 5.70 11.10 9.05 15.00 Socket - Female Crimp Contact Contact Size 12, 16, 16S Contact Size 8 Contact Size 4 Contact Size 0 CONTACT PART NO CONTACT SIZE 'B' 97B - 108456 97B - 108457 97B - 110262 97B - 108387 97B - 111878 97B - 112068 16S 16 12 8 4 0 3.10 3.10 4.78 7.85 11.10 15.00 47 'C' 'D' 1.72 2.60 1.72 2.60 2.51 3.96 4.57 6.75 7.15 9.50 11.90 13.90 'L' 26.30 34.20 37.00 37.00 40.00 44.45 'C' 'D' 1.72 2.60 1.72 2.60 2.51 3.96 4.57 6.75 7.15 9.50 11.90 13.90 'L' 26.00 30.50 36.60 40.70 40.70 44.45 Dummy Receptacle Rear Side Closed `R' SQ. oD SHELL +0.0 SIZE -0.13 `M' `K' `A' 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 `D' FLANGE RELATIVE TO HOLES EQUAL WITHIN 0.38 (8 PLACES) `S' SQ Q (4 HOLES) `T' Q1 `A' 18.19 21.30 24.59 'K' +-0.38 -0.0 Q T R 'M' S +-0.10 Q1 +0.18 +0.23 +0.18 +-0.13 -0.0 -0.25 0.20 2.79 3.20 27.38 30.78 34.16 37.36 40.87 46.68 53.36 59.56 25.40 18.21 33.32 28.05 20.60 36.20 30.0 23.01 39.67 14.20 3.23 M4 32.51 24.61 42.87 35.05 38.0 40.99 44.45 3.99 3.73 50.80 57.10 4.32 M5 63.50 19.0 20.60 22.20 27.0 29.39 31.80 34.90 39.70 44.50 49.20 46.02 50.80 53.98 60.32 66.68 76.20 84.12 Dummy Receptacle Rear Side Open (Hollow) `R' `Q' oD SHELL +0.0 SIZE -0.13 `M' `K' (4 HOLES) `A' 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 `D' FLANGE RELATIVE TO HOLES EQUAL WITHIN 0.38 (8 PLACES) `S' SQ. `T' SQ. SECTION `A-A' Q1 `A' 18.19 21.30 24.59 'K' +-0.38 -0.0 Q T R 'M' S +-0.10 Q1 +0.18 +0.23 +0.18 +-0.13 -0.0 -0.25 0.20 2.79 25.40 18.21 33.32 28.05 20.60 36.20 30.0 23.01 39.67 14.20 3.20 3.23 27.38 30.78 34.16 37.36 40.87 46.68 53.36 59.56 19.0 20.60 22.20 M4 32.51 24.61 42.87 35.05 38.0 40.99 44.45 3.99 3.73 50.80 57.10 M5 4.32 63.50 27.0 29.39 31.80 34.90 39.70 44.50 49.20 46.02 50.80 53.98 60.32 66.68 76.20 84.12 ORDERING INFO 97B-3105-XX-CF SERIES DESIGNATION CF-CLOSED FLANGE HF-HOLLOW FLANGE DESIGNATION FOR DUMMY RECEPTACLE SHELL SIZE Thru Bulkhead Receptacle L K A S SQ M R SQ Q ORDERING INFO TBH-97BS-XX-YY PS THRU BULKHEAD SERIES SHELL SIZE 'A' +0.0 -0.15 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 18.21 21.40 24.61 27.41 27.41 30.81 34.19 37.39 40.89 46.71 53.39 59.59 'M' 'K' +0.41 +-0.20 -0.0 2.79 3.20 3.20 3.20 3.20 3.99 3.99 3.99 3.99 3.99 3.99 3.99 14.20 14.20 14.20 14.20 19.00 19.00 19.00 19.00 20.60 20.60 22.20 22.20 'R' +-0.10 'S' +-0.20 'L' MAX. 18.20 20.60 23.00 24.60 24.60 27.00 29.40 31.80 34.90 39.70 44.50 49.20 25.40 28.00 30.00 32.50 32.50 35.00 38.00 41.00 44.50 50.80 57.00 63.50 37.75 37.75 37.75 37.75 51.40 51.40 51.40 51.40 51.40 51.40 51.40 51.40 PIN & SOCKET CONTACT SERIES DESIGNATION INSERT ARRANGEMENT 48 MS/97B Connector- Accessories Crimp contact Contacts for MS/97B connectors are machined from copper alloys and silver plated for maximum corrosion resistance, with a minimum millivolt drop and a maximum current carrying capacity; the size 16 and 12 socket contacts are of the closed entry design. Gold plated contacts are also available. Part Number For Crimp Contacts only* MS-106433 Pin/ Socket Pin MS-108456 Socket MS-108295 Pin MS-108457 Socket MS-108388 Pin MS-110262 Socket MS-108386 Pin MS-108387 Socket MS-108384 Pin MS-111878 Socket MS-112067 Pin MS-112068 Socket Mating End Size Wire Barrel Size 16 Short 16 16 Long 16 12 12 Allowable Wire size Test Current*** Amps Insertion/Removal Tool 16 18 60 22** 16 18 20 22** 13 10 7.5 5 13 10 7.5 5 12 14 23 17 97B-IR-12 97B-IR-16 97B-IR-16 8 8 8 10** 46 33 97B-IR-8 4 4 4 6** 80 60 97B-IR-4 0 0 0 1 2** 150 125 97B-IR-0 * Solder contacts are not sold as separate items. Part numbers shown here are for crimp contacts only. ** When using wire adapter sleeve shown. *** Contact rating as stated are test ratings only. The connecter may not withstand full rated current through all contacts continuously. Please note that the electrical data given is not an establishment of electrical safety factors. This is left entirely in the designers hands as he can best determine which peak voltage, switching surges, transients, etc. can be expected in a particular circuit. MS/97B Connectors Application tools When proprietary crimp contacts are employed rather than the standard MS approved solder contacts, the following application tools are recommended for use. There is a possibility of additional crimping tools other than those included being available at present or in the future for this specific application. TOOLING CHART Crimping Tool Positioner/ Turret M22520/1-01 * M22520/1-01 * ** ** ** ** ** ** * Use Daniels Turret TH29-1 or Astro Tool Co. Turret 616266 ** For appropriate crimp tool and positioner refer to Pico Crimping Tool Co. Tools used with Arbor Press 11-7364 49 O rdering MS/97B series To obtain the specific connector required, write down the connector number from the typical example below. Only inserts shown in the availability chart shown on page 7 can be specified. Connectors are delivered with protective plastic dust covers. Include premating contact designation only if premating contact is required. The second letter in the premating contact designation stands for the actual contact position. B at the end of the connector number indicates telescopic bushing provided. MS - 3 A - 18 - 19 - P - W - PC - PTC9 100 PC- Premating contact designation Series designation See pages 8 to 18 MS - Threaded version 97B - Bayonet version 3 4 Alternate positions W-X-Y-Z (No suffix - Normal) - Solder - Crimp See insert orientations on page 6. Shell style 100 - Wall mounting receptacle 101 102E Cable connecting receptacle - Box mounting receptacle (Do not accept accessory) 103 - Back box mounting receptacle (Do not accept accessory) 103X - Back Box Mounting Receptacle to accept the accessory (Replace X with suitable accessory) Dummy receptacle 105 105A 106 107 107X 108 Contact type - P - Pin contacts S - Socket contacts Standard - Silver plating Note : Contact factory for gold plating part number. Insert arrangement Straight plug connector without accessory & serration See pages 7 to 18 - Straight plug to accept the accessory (Replace X with suitable accessory) - Jam nut Receptacle (Do not accept accessory) - Jam nut Receptacle to accept accessory (Replace X with suitable accessory) - Right angle plug connector Shell size 10S, 10SL, 12S, 12, 14S, 14, 16S, 16, 18, 20, 22, 24, 28, 32, 36. Connector Modification Connector class (Accessory/Backshell) A -Solid Backshell suitable for straight Plug AG - Solid Backshell with Enviromental sealing Grommet F - Strain relief Backshell with Enviromental sealing Grommet (E & F are same) R- Shorter length Backshell with Environmental sealing grommet PGXX - PG Threaded Backshell to accept the PG gland (Replace XX with suitable thread size) MXX - Metric Threaded Backshell to accept the Metric gland (Replace XX with suitable thread size) G- Backshell suitable for heat shrink tubing with Environmental sealing Grommet SQ- Backshell suitable for heat shrink tubing & shielding with Environmental sealing Grommet EGM- Backshell with Metal ferrule suitable for shielded cable to suit variable cable sizes PHM- Backshell with out Metal ferrule suitable for unshielded cable to suit variable cable sizes RT- Right angle Backshell suitable for 100,101,103X Style Note: Connector 3103 supplied in two types. Connector with rear end thread to accept backshell & without rear end thread. To order 3103 without rear end thread do not add any connector class such as ( A,E,F,R...) & hence it is similar to 3102 with Back Box mount For e.g 97B-3103-18-1P-622 Connector without thread Standard connector supplied with Cadmium plating with Olivedrab Chromate Green conductive Finish 622 - Cadmium Free Zinc Cobalt Green conductive Finish (RoHS Compliant) 624 - Cadmium Free Zinc Cobalt Black conductive Finish (RoHS Compliant) 726 - Electrophoratic Black Non conductive finish (RoHS Compliant) A23 - Electoless Nickel Finish (RoHS Compliant) 9 - No solder Filling to contact applicable only for MS connector 563 - 0.5 micron gold plated contacts (standard silver plated contacts) 97BS - If added to receptacle part number connector supplied with SS wear pin 97BS - If added to Plug part number connector supplied with Roller Stud (Shell Size 18-40) B - Strain relief BIS supplied with M3420 bushing CXX - Crimp contact suitable XX AWG size F0/LC - Less contacts F42 - Less grommet & backshell HD - Heavy duty coupling ring RFI - Plug conn with grounding fingure SQG - Square flange gasket applicable to receptacle for (100/102/103) SR - MS3057 - XXA Cable Clamp SRC - MS3057 - XXC Cable Clamp T 00 - Metric THD holes in Flange Applicable for (100/102/103) PTC9 - PC Tail Connector (Refer Page 25) Notice : All information, including illustrations given herein is believed to be accurate at the time of printing. In lieu of design advances, Amphenol reserves the right to change specifications without notice. This publication ACRMS02 03/13 MS AND 97B Series Connectors supercedes all existing Amphenol literature on MS AND 97 B Series Connectors. 50 NORTH AMERICA Sales & Product Support Amphenol PCD 72 Cherry Hill Drive Beverly, MA 01915 USA Tel: +1-978-624-3400 Fax: +1-978-927-1513 info@amphenolpcd.com www.amphenolpcd.com www.backshellworld.com Amphenol Aerospace Operations 40-60, Delaware Avenue Sidney, NY 13838-1395 Tel: +1-607-563-5011 Fax: +1-607-563-5357 Amphenol Canada Meford Drive Scarborough, ON MIB 2X6 Tel: +416-291-4401 Fax: +416-292-0647 Amphenol Fiber Systems International 1300 Central Expressway North Suite 100 Allen,Texas 75013, USA Tel: +1-214-547-2400 Fax: +1-214-547-9344 EUROPE France United Kingdom Germany Italy Amphenol Socapex S.A.S. 948,Promenade de I'Arve Bp29, Thyez Cedex 74311, France Tel: +33-4-5089-2800 Fax: +33-4-5096-1941 Amphenol Limited Thanet Way, Whitstable Kent CT5 3JF, England Tel: +44-1227-773-200 Fax: 44-1227-276-571 Amphenol-Air LB GmbH Am Kleinbahnhof 4 Saarlouis D-66740, Germany Tel: 49-6831-9810-00 Fax: 49-6831-9810-30 Via Barbaiana 5 20020 Lainate (Milano) Italy Tel :+39-02-93254.209 +39-02-93254.214 Fax:+39-02-93254-444 Spain Austria Amphenol Iberica Edificio Burgosol Oficina N 55 C/Comunidad de Madrid 35 bis Las Rozas (Madrid) Tel: +34-91-6407302 +34-91-6407306 Fax:+34-91-6407307 Amphenol Austria Wiener Gasse 68 2380, Erchtoldsdarf, Austria Tel : + 43-69910396071 Fax: + 43-69940306071 Holland Amphenol Benelux Zadelmaker 121 NL-2401 PD Alphen aan den Rijn Holland Tel:+31-172-444903 Fax:+31-172 240254 Amphenol Air-LB Immeuble Le Doublon 11, Avenue Dobonnet Courbevoice-Cedex 92407, France Ph: +33-1-4905-3000 Fax: +33-1-4905-3043 Center & East Europe Amphenol Wiener Gasse 68 2380 Perchtoldsdorf Tel: +43-699-10396071 Fax: +43 699 40396071 Sweden Amphenol Industrial and Military & Aerospace Nordic & Baltic Military Phone/ Mobile+46702129200 Industrial +46 767909560 ASIA India Amphenol Interconnect India Pvt. Ltd. 105 Bhosari Industrial Area Pune-411026, India Tel: +9120-3068-8305 Fax:+9120-2712-9158 Amphenol Interconnect India Pvt. Ltd. 61 Electronics City Bangalore-560 100, India Ph: +9180-2852-3838 Fax: +9180-2852-0418 Japan Amphenol Japan 471-1, Deba, Ritto City Shiga 520-3041, Japan Tel: +81-77-553-8501 Fax: +81-77-551-2200 Singapore Amphenol East Asia Ltd. 72 Bendemeer Road # 03-33 Luzerne Singapore 339 941 Tel: 65-6294-2128 Fax: 65-6294-3522 Korea Amphenol Daeshin Electronics 558 SoSa, SongNae, Bucheon-City Kyunggi-Do, Korea 420-130 Tel: +82-32-610-3800 Fax: +92-32-673-2507 China Amphenol PCD Shenzhen 3/F Building, A4 Songbai Industrial Park East Road of Minghuan Gongming Town, Baon District Shenchen, China Tel: +86-755-8173-8000 Fax: +86-755-8173-8180 ROW Australia Africa Russia Amphenol Australia Pty Ltd 2 Fiveways Boulevard Keysborough VIC 3173 Ph: +61-3-8796-8888 Fax: +61-3-8796-8801 Amphenol South Africa 30 Impala Road 2196 Sandton-Chistlehurston South Africa Tel: +27-11-783-9517 Fax: +27-11-783-9519 Amphenol Russia 8-2 Yaroslavskaja Str 129164 Moscow, Russia Tel: +7-495-937-6341 Fax: +7-495-937-6319 Israel Bar-Tec Ltd. P.O. Box 279 Kfar Sava, 44102 Israel Tel: +972-9-7644100 Fax: +972-9-7674324 Maslak 34396 Istanbul Tel: +90-212-335-2501 Fax: +90-212-335-2500 Brazil Amphenol do Brasil Ltda Rua Diogo Moreira 132 CEP 05423-010 Sao Paulo-SP, Brazil Tel: +55-11-3815-1003 Fax: +55-11-3815-1629 Argentina Amphenol Argentina Avenida Callao 930 2nd Floor, Office B Plaza C1023AAP Buenos Aires Argentina Tel: 54-11-4815-6886 Fax: 54-11-4814-5779 Bangalore Operations Pune Operations Our offices in India: MARKETING HEADQUARTERS Southern Region Northern and Eastern Region 105, Bhosari Industrial Area, Pune - 411 026. Tel.: 91-20-30688303, 30688304 Fax : 91-20-30688321 Email : vbhavsar@amphenol-in.com sales@amphenol-in.com 4931, 11th Floor, High Point IV 45, Palace Road, Bangalore 560 001. Tel.: 91-80-22281392, 22281002 Fax : 91-80-22253859 Email : kmanoj@amphenol-in.com 1414, 14th Floor, Chiranjiv Tower, 43, Nehru Place, New Delhi - 110 019. Tel. : 91-11-26449177 Telefax : 91-11-26449176 Email : sunily@amphenol-in.com Export Western Region Central Region 105, Bhosari Industrial Area, Pune - 411 026, India. Tel.: 91-20-30688305, 30688353 Fax : 91-20-27129158 Email : svpatil@amphenol-in.com 105, Bhosari Industrial Area, Pune - 411 026. Tel.: 91-20-27119735, 30688334 Fax: 91-20-27120581, 27119735 Email : sunilp@amphenol-in.com 107, 1st Floor, `Am Sri Classic', Sarojinidevi Road, Secunderabad - 500 003. Telefax : 91-40-66332906 Email : pprasad@amphenol-in.com www.amphenol-in.com