2002-2011 Microchip Technology Inc. DS21749J-page 1
93AA46A/B/C, 93LC46A/B/C,
93C46A/B/C
Device Selection Table
Features:
• Low-Power CMOS Technology
• ORG Pin to Select Word Size for ‘46C’ Version
• 128 x 8-bit Organization ‘A’ Devices (no ORG)
• 64 x 16-bit Organization ‘B’ Devices (no ORG)
• Self-Timed Erase/Write Cycles (including
Auto-Erase)
• Automatic Erase All (ERAL) Before Write All
(WRAL)
• Power-On/Off Data Protection Circuitry
• Industry Standard 3-Wire Serial I/O
• Device Status Signal (Ready/Busy)
• Sequential Read Function
• 1,000,000 Erase/Write Cycles
• Data Retention > 200 Years
• Pb-free and RoHS Compliant
• Temperature Ranges Supported:
Pin Function Table
Description:
The Microchip Technology Inc. 93XX46A/B/C devices
are 1Kbit low-voltage serial Electrically Erasable
PROMs (EEPROM). Word-selectable devices such as
the 93AA46C, 93LC46C or 93C46C are dependent
upon external logic levels driving the ORG pin to set
word size. For dedicated 8-bit communication, the
93AA46A, 93LC46A or 93C46A devices are available,
while the 93AA46B, 93LC46B and 93C46B devices
provide dedicated 16-bit communication. Advanced
CMOS technology makes these devices ideal for low-
power, nonvolatile memory applications. The entire
93XX Series is available in standard packages includ-
ing 8-lead PDIP and SOIC, and advanced packaging
including 8-lead MSOP, 6-lead SOT-23, 8-lead
2x3 DFN/TDFN and 8-lead TSSOP. All packages are
Pb-free (Matte Tin) finish.
Part Number VCC Range ORG Pin Word Size Temp Ranges Packages
93AA46A 1.8-5.5 No 8-bit I P, SN, ST, MS, OT, MC, MN
93AA46B 1.8-5-5 No 16-bit I P, SN, ST, MS, OT, MC, MN
93LC46A 2.5-5.5 No 8-bit I, E P, SN, ST, MS, OT, MC, MN
93LC46B 2.5-5.5 No 16-bit I, E P, SN, ST, MS, OT, MC, MN
93C46A 4.5-5.5 No 8-bit I, E P, SN, ST, MS, OT, MC, MN
93C46B 4.5-5.5 No 16-bit I, E P, SN, ST, MS, OT, MC, MN
93AA46C 1.8-5.5 Yes 8- or 16-bit I P, SN, ST, MS, MC, MN
93LC46C 2.5-5.5 Yes 8- or 16-bit I, E P, SN, ST, MS, MC, MN
93C46C 4.5-5.5 Yes 8- or 16-bit I, E P, SN, ST, MS, MC, MN
- Industrial (I) -40°C to +85°C
- Automotive (E) -40°C to +125°C
Name Function
CS Chip Select
CLK Serial Data Clock
DI Serial Data Input
DO Serial Data Output
VSS Ground
NC No internal connection
ORG Memory Configuration
VCC Power Supply
1K Microwire Compatible Serial EEPROM
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 2 2002-2011 Microchip Technology Inc.
Package Types (not to scale)
CS
CLK
DI
DO
1
2
3
4
8
7
6
5
V
CC
NC
ORG
*
V
SS
PDIP/SOIC
(P, SN)
CS
CLK DI
DO
1
2
3
4
8
7
6
5
V
CC
NC ORG*
V
SS
ROTATED SOIC
(ex: 93LC46BX)
TSSOP/MSOP
CS
CLK
DI
DO
1
2
3
4
8
7
6
5
V
CC
NC
ORG*
V
SS
(ST, MS) SOT-23
DO
V
SS
DI
1
2
3
6
5
4
V
CC
CS
CLK
(OT)
*ORG pin is NC on A/B devices
DFN/TDFN
CS
CLK
DI
DO
NC
ORG*
VSS
VCC
8
7
6
5
1
2
3
4
(MC, MN)
2002-2011 Microchip Technology Inc. DS21749J-page 3
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. VSS ..........................................................................................................-0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins 4kV
TABLE 1-1: DC CHARACTERISTICS
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
All parameters apply over the specified
ranges unless otherwise noted.
Industrial (I): TA = -40°C to +85°C, VCC = +1.8V TO +5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V TO +5.5V
Param.
No. Symbol Parameter Min. Typ Max. Units Conditions
D1 VIH1
VIH2
High-level input voltage 2.0
0.7 VCC
—
—
VCC +1
VCC +1
V
V
VCC 2.7V
VCC 2.7V
D2 VIL1
VIL2
Low-level input voltage -0.3
-0.3
—
—
0.8
0.2 VCC
V
V
VCC 2.7V
VCC 2.7V
D3 VOL1
VOL2
Low-level output voltage —
—
—
—
0.4
0.2
V
V
IOL = 2.1 mA, VCC = 4.5V
IOL = 100 A, VCC = 2.5V
D4 VOH1
VOH2
High-level output voltage 2.4
VCC - 0.2
—
—
—
—
V
V
IOH = -400 A, VCC = 4.5V
IOH = -100 A, VCC = 2.5V
D5 ILI Input leakage current — — ±1 AVIN = VSS or VCC
D6 ILO Output leakage current — — ±1 AVOUT = VSS or VCC
D7 CIN,
COUT
Pin capacitance
(all inputs/outputs)
——7pFVIN/VOUT = 0V (Note 1)
T
A = 25°C, FCLK = 1 MHz
D8 ICC
write
Write current —
—
—
500
2
—
mA
A
FCLK = 3 MHz, VCC = 5.5V
FCLK = 2 MHz, VCC = 2.5V
D9 ICC read Read current —
—
—
—
—
100
1
500
—
mA
A
A
FCLK = 3 MHz, VCC = 5.5V
FCLK = 2 MHz, VCC = 3.0V
FCLK = 2 MHz, VCC = 2.5V
D10 ICCS Standby current —
—
—
—
1
5
A
A
I-Temp
E-Temp
CLK = CS = 0V
ORG = DI = VSS or VCC
(Note 2) (Note 3)
D11 VPOR VCC voltage detect
—
—
1.5
3.8
—
—
V
V
(Note 1)
93AA46A/B/C, 93LC46A/B/C
93C46A/B/C
Note 1: This parameter is periodically sampled and not 100% tested.
2: ORG pin not available on ‘A’ or ‘B’ versions.
3: Ready/Busy status must be cleared from DO; see Section 3.4 “Data Out (DO)”.
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 4 2002-2011 Microchip Technology Inc.
TABLE 1-2: AC CHARACTERISTICS
All parameters apply over the specified
ranges unless otherwise noted.
Industrial (I): T
A = -40°C to +85°C, VCC = +1.8V TO +5.5V
Automotive (E): T
A = -40°C to +125°C, VCC = +2.5V TO +5.5V
Param.
No. Symbol Parameter Min. Max. Units Conditions
A1 FCLK Clock frequency — 3
2
1
MHz
MHz
MHz
4.5VVCC 5.5V, 93XX46C only
2.5V VCC 5.5V
1.8V VCC 2.5V
A2 TCKH Clock high time 200
250
450
—ns
ns
ns
4.5VVCC 5.5V, 93XX46C only
2.5V VCC 5.5V
1.8V VCC 2.5V
A3 TCKL Clock low time 100
200
450
—ns
ns
ns
4.5VVCC 5.5V, 93XX46C only
2.5V VCC 5.5V
1.8V VCC 2.5V
A4 TCSS Chip Select setup time 50
100
250
—ns
ns
ns
4.5VVCC 5.5V
2.5V VCC 4.5V
1.8V VCC 2.5V
A5 TCSH Chip Select hold time 0 — ns 1.8V VCC 5.5V
A6 TCSL Chip Select low time 250 — ns 1.8V VCC 5.5V
A7 TDIS Data input setup time 50
100
250
—ns4.5VVCC 5.5V, 93XX46C only
2.5V VCC 5.5V
1.8V VCC 2.5V
A8 TDIH Data input hold time 50
100
250
—ns4.5VVCC 5.5V, 93XX46C only
2.5V VCC 5.5V
1.8V VCC 2.5V
A9 TPD Data output delay time —
—
—
200
250
400
ns 4.5VVCC 5.5V, CL = 100 pF
2.5V VCC 4.5V, CL = 100 pF
1.8V VCC 2.5V, CL = 100 pF
A10 TCZ Data output disable time —
—
100
200
ns 4.5VVCC 5.5V, (Note 1)
1.8VVCC 4.5V, (Note 1)
A11 TSV Status valid time — 200
300
500
ns 4.5VVCC 5.5V, CL = 100 pF
2.5V VCC 4.5V, CL = 100 pF
1.8V VCC 2.5V, CL = 100 pF
A12 TWC Program cycle time — 6 ms Erase/Write mode (AA and LC
versions)
A13 TWC — 2 ms Erase/Write mode (93C versions)
A14 TEC — 6 ms ERAL mode, 4.5V VCC 5.5V
A15 TWL — 15 ms WRAL mode, 4.5V VCC 5.5V
A16 — Endurance 1M — cycles 25°C, VCC = 5.0V, (Note 2)
Note 1: This parameter is periodically sampled and not 100% tested.
2: This application is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model, which may be obtained from Microchip’s web
site at www.microchip.com.
2002-2011 Microchip Technology Inc. DS21749J-page 5
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
FIGURE 1-1: SYNCHRONOUS DATA TIMING
TABLE 1-3: INSTRUCTION SET FOR X16 ORGANIZATION (93XX46B OR 93XX46C WITH ORG = 1)
TABLE 1-4: INSTRUCTION SET FOR X8 ORGANIZATION (93XX46A OR 93XX46C WITH ORG = 0)
Instruction SB Opcode Address Data In Data Out Req. CLK Cycles
ERASE 1 11 A5 A4 A3 A2 A1 A0 — (RDY/BSY)9
ERAL 1 00 10XXXX — (RDY/BSY)9
EWDS 1 00 00XXXX — High-Z 9
EWEN 1 00 11XXXX — High-Z 9
READ 1 10 A5 A4 A3 A2 A1 A0 — D15 - D0 25
WRITE 1 01 A5 A4 A3 A2 A1 A0 D15 - D0 (RDY/BSY)25
WRAL 1 00 01XXXXD15 - D0 (RDY/BSY)25
Instruction SB Opcode Address Data In Data Out Req. CLK Cycles
ERASE 1 11 A6 A5 A4 A3 A2 A1 A0 — (RDY/BSY)10
ERAL 1 00 10XXXXX — (RDY/BSY)10
EWDS 1 00 00XXXXX —High-Z 10
EWEN 1 00 11XXXXX —High-Z 10
READ 1 10 A6 A5 A4 A3 A2 A1 A0 — D7 - D0 18
WRITE 1 01 A6 A5 A4 A3 A2 A1 A0 D7 - D0 (RDY/BSY)18
WRAL 1 00 01XXXXX D7 - D0 (RDY/BSY)18
CS VIH
VIL
VIH
VIL
VIH
VIL
VOH
VOL
VOH
VOL
CLK
DI
DO
(Read)
DO
(Program)
TCSS
TDIS
TCKH TCKL
TDIH
TPD
TCSH
TPD
TCZ
Status Valid
TSV
TCZ
Note: TSV is relative to CS.
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 6 2002-2011 Microchip Technology Inc.
2.0 FUNCTIONAL DESCRIPTION
When the ORG pin (93XX46C) is connected to VCC,
the (x16) organization is selected. When it is connected
to ground, the (x8) organization is selected. Instruc-
tions, addresses and write data are clocked into the DI
pin on the rising edge of the clock (CLK). The DO pin is
normally held in a High-Z state except when reading
data from the device, or when checking the Ready/
Busy status during a programming operation. The
Ready/Busy status can be verified during an erase/
write operation by polling the DO pin; DO low indicates
that programming is still in progress, while DO high
indicates the device is ready. DO will enter the High-Z
state on the falling edge of CS.
2.1 Start Condition
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device
operation (Read, Write, Erase, EWEN, EWDS, ERAL
or WRAL). As soon as CS is high, the device is no
longer in Standby mode.
An instruction following a Start condition will only be
executed if the required opcode, address and data bits
for any particular instruction are clocked in.
2.2 Data In/Data Out (DI/DO)
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin. In order to
limit this current, a resistor should be connected
between DI and DO.
2.3 Data Protection
All modes of operation are inhibited when VCC is below
a typical voltage of 1.5V for ‘93AA’ and ‘93LC’ devices
or 3.8V for ‘93C’ devices.
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before the initial ERASE or WRITE instruction
can be executed.
Block Diagram
Note: When preparing to transmit an instruction,
either the CLK or DI signal levels must be
at a logic low as CS is toggled active high.
Note: For added protection, an EWDS command
should be performed after every write
operation and an external 10 k pull-
down protection resistor should be added
to the CS pin.
Memory
Array
Data Register
Mode
Decode
Logic
Clock
Register
Address
Decoder
Address
Counter
Output
Buffer
DO
DI
ORG*
CS
CLK
VCC VSS
*ORG input is not available on A/B devices
2002-2011 Microchip Technology Inc. DS21749J-page 7
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
2.4 Erase
The ERASE instruction forces all data bits of the
specified address to the logical ‘1’ state. CS is brought
low following the loading of the last address bit. This
falling edge of the CS pin initiates the self-timed
programming cycle, except on ‘93C’ devices where the
rising edge of CLK before the last address bit initiates
the write cycle.
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL). DO at logical ‘0’ indicates that programming
is still in progress. DO at logical ‘1’ indicates that the
register at the specified address has been erased and
the device is ready for another instruction.
FIGURE 2-1: ERASE TIMING FOR 93AA AND 93LC DEVICES
FIGURE 2-2: ERASE TIMING FOR 93C DEVICES
Note: After the Erase cycle is complete, issuing
a Start bit and then taking CS low will clear
the Ready/Busy status from DO.
CS
CLK
DI
DO
TCSL
Check Status
111ANAN-1 AN-2 ••• A0
TSV TCZ
Busy Ready
High-Z
TWC
High-Z
CS
CLK
DI
DO
TCSL
Check Status
111ANAN-1 AN-2 ••• A0
TSV TCZ
Busy Ready
High-Z
TWC
High-Z
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 8 2002-2011 Microchip Technology Inc.
2.5 Erase All (ERAL)
The Erase All (ERAL) instruction will erase the entire
memory array to the logical ‘1’ state. The ERAL cycle
is identical to the erase cycle, except for the different
opcode. The ERAL cycle is completely self-timed and
commences at the falling edge of the CS, except on
‘93C’ devices where the rising edge of CLK before the
last data bit initiates the write cycle. Clocking of the
CLK pin is not necessary after the device has entered
the ERAL cycle.
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL).
VCC must be 4.5V for proper operation of ERAL.
FIGURE 2-3: ERAL TIMING FOR 93AA AND 93LC DEVICES
FIGURE 2-4: ERAL TIMING FOR 93C DEVICES
Note: After the ERAL command is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
CS
CLK
DI
DO
TCSL
Check Status
100 10x
••• x
TSV TCZ
Busy Ready
High-Z
TEC
High-Z
VCC must be 4.5V for proper operation of ERAL.
CS
CLK
DI
DO
TCSL
Check Status
100 10x
••• x
TSV TCZ
Busy Ready
High-Z
TEC
High-Z
2002-2011 Microchip Technology Inc. DS21749J-page 9
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
2.6 Erase/Write Disable and Enable
(EWDS/EWEN)
The 93XX46A/B/C powers up in the Erase/Write Disable
(EWDS) state. All programming modes must be preceded
by an Erase/Write Enable (EWEN) instruction. Once the
EWEN instruction is executed, programming remains
enabled until an EWDS instruction is executed or Vcc is
removed from the device.
To protect against accidental data disturbance, the EWDS
instruction can be used to disable all erase/write functions
and should follow all programming operations. Execution
of a READ instruction is independent of both the EWEN and
EWDS instructions.
FIGURE 2-5: EWDS TIMING
FIGURE 2-6: EWEN TIMING
2.7 Read
The READ instruction outputs the serial data of the
addressed memory location on the DO pin. A dummy
zero bit precedes the 8-bit (if ORG pin is low or A-version
devices) or 16-bit (if ORG pin is high or B-version
devices) output string.
The output data bits will toggle on the rising edge of the
CLK and are stable after the specified time delay (TPD).
Sequential read is possible when CS is held high. The
memory data will automatically cycle to the next register
and output sequentially.
FIGURE 2-7: READ TIMING
CS
CLK
DI 10
000x ••• x
TCSL
1x
CS
CLK
DI 00 1 1x
TCSL
•••
CS
CLK
DI
DO
110
AN••• A0
High-Z 0Dx ••• D0 Dx ••• D0 •••
Dx D0
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 10 2002-2011 Microchip Technology Inc.
2.8 Write
The WRITE instruction is followed by 8 bits (if ORG is
low or A-version devices) or 16 bits (if ORG pin is high
or B-version devices) of data, which are written into the
specified address. For 93AA46A/B/C and 93LC46A/B/C
devices, after the last data bit is clocked into DI, the
falling edge of CS initiates the self-timed auto-erase and
programming cycle. For 93C46A/B/C devices, the self-
timed auto-erase and programming cycle is initiated by
the rising edge of CLK on the last data bit.
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL). DO at logical ‘0’ indicates that programming
is still in progress. DO at logical ‘1’ indicates that the
register at the specified address has been written with
the data specified and the device is ready for another
instruction.
FIGURE 2-8: WRITE TIMING FOR 93AA AND 93LC DEVICES
FIGURE 2-9: WRITE TIMING FOR 93C DEVICES
Note: After the Write cycle is complete, issuing a
Start bit and then taking CS low will clear
the Ready/Busy status from DO.
CS
CLK
DI
DO
101AN••• A0 Dx ••• D0
Busy Ready High-Z
High-Z
TWC
TCSL
TCZ
TSV
CS
CLK
DI
DO
101AN••• A0 Dx ••• D0
Busy Ready High-Z
High-Z
TWC
TCSL
TCZ
TSV
2002-2011 Microchip Technology Inc. DS21749J-page 11
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
2.9 Write All (WRAL)
The Write All (WRAL) instruction will write the entire
memory array with the data specified in the command.
For 93AA46A/B/C and 93LC46A/B/C devices, after the
last data bit is clocked into DI, the falling edge of CS
initiates the self-timed auto-erase and programming
cycle. For 93C46A/B/C devices, the self-timed auto-
erase and programming cycle is initiated by the rising
edge of CLK on the last data bit. Clocking of the CLK
pin is not necessary after the device has entered the
WRAL cycle. The WRAL command does include an
automatic ERAL cycle for the device. Therefore, the
WRAL instruction does not require an ERAL instruction,
but the chip must be in the EWEN status.
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL).
VCC must be 4.5V for proper operation of WRAL.
FIGURE 2-10: WRAL TIMING FOR 93AA AND 93LC DEVICES
FIGURE 2-11: WRAL TIMING FOR 93C DEVICES
Note: After the Write All cycle is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
CS
CLK
DI
DO
HIGH-Z
10001 x
••• xDx ••• D0
High-Z Busy Ready
TWL
VCC must be 4.5V for proper operation of WRAL.
TCSL
TSV TCZ
CS
CLK
DI
DO
HIGH-Z
10001 x
••• xDx ••• D0
High-Z Busy Ready
TWL
TCSL
TSV TCZ
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 12 2002-2011 Microchip Technology Inc.
3.0 PIN DESCRIPTIONS
TABLE 3-1: PIN DESCRIPTIONS
3.1 Chip Select (CS)
A high level selects the device; a low level deselects
the device and forces it into Standby mode. However, a
programming cycle that is already in progress will be
completed, regardless of the Chip Select (CS) input
signal. If CS is brought low during a program cycle, the
device will go into Standby mode as soon as the
programming cycle is completed.
CS must be low for 250 ns minimum (T
CSL) between
consecutive instructions. If CS is low, the internal
control logic is held in a Reset status.
3.2 Serial Clock (CLK)
The Serial Clock is used to synchronize the communi-
cation between a master device and the 93XX series
device. Opcodes, address and data bits are clocked in
on the positive edge of CLK. Data bits are also clocked
out on the positive edge of CLK.
CLK can be stopped anywhere in the transmission
sequence (at high or low level) and can be continued
anytime with respect to clock high time (TCKH) and
clock low time (TCKL). This gives the controlling master
freedom in preparing opcode, address and data.
CLK is a “don't care” if CS is low (device deselected). If
CS is high, but the Start condition has not been
detected (DI = 0), any number of clock cycles can be
received by the device without changing its status (i.e.,
waiting for a Start condition).
CLK cycles are not required during the self-timed write
(i.e., auto erase/write) cycle.
After detection of a Start condition the specified number
of clock cycles (respectively low-to-high transitions of
CLK) must be provided. These clock cycles are
required to clock in all required opcode, address and
data bits before an instruction is executed. CLK and DI
then become “don't care” inputs waiting for a new Start
condition to be detected.
3.3 Data In (DI)
Data In (DI) is used to clock in a Start bit, opcode,
address and data synchronously with the CLK input.
3.4 Data Out (DO)
Data Out (DO) is used in the Read mode to output data
synchronously with the CLK input (TPD after the
positive edge of CLK).
This pin also provides Ready/Busy status information
during erase and write cycles. Ready/Busy status infor-
mation is available on the DO pin if CS is brought high
after being low for minimum Chip Select low time (TCSL)
and an erase or write operation has been initiated.
The Status signal is not available on DO if CS is held
low during the entire erase or write cycle. In this case,
DO is in the High-Z mode. If status is checked after the
erase/write cycle, the data line will be high to indicate
the device is ready.
3.5 Organization (ORG)
When the ORG pin is connected to VCC or Logic HI, the
(x16) memory organization is selected. When the ORG
pin is tied to VSS or Logic LO, the (x8) memory
organization is selected. For proper operation, ORG
must be tied to a valid logic level.
93XX46A devices are always (x8) organization and
93XX46B devices are always (x16) organization.
Name PDIP SOIC TSSOP MSOP DFN(1) TDFN(1) SOT-23 Rotated
SOIC Function
CS 1 1 1 1 1 1 5 3 Chip Select
CLK 2 2 2 2 2 2 4 4 Serial Clock
DI 3 3 3 3 3 3 3 5 Data In
DO 4 4 4 4 4 4 1 6 Data Out
Vss 5 5 5 5 5 5 2 7 Ground
ORG/NC 6 6 6 6 6 6 — 8 Organization/93XX46C
No Internal Connection/
93XX46A/B
NC 7 7 7 7 7 7 — 1 No Internal Connection
VCC 8 8 8 8 8 8 6 2 Power Supply
Note 1: The exposed pad on the DFN/TDFN packages can be connected to VSS or left floating.
Note: After a programming cycle is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
2002-2011 Microchip Technology Inc. DS21749J-page 13
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
4.0 PACKAGING INFORMATION
4.1 Package Marking Information
Example:
6-Lead SOT-23
8-Lead MSOP (150 mil) Example:
XXXXXXT
YWWNNN
3L46BI
5281L7
XXNN 1EL7
T/XXXNNN
XXXXXXXX
YYWW
8-Lead PDIP
8-Lead SOIC
XXXXYYWW
XXXXXXXT
NNN
XXXX
TYWW
8-Lead TSSOP
NNN
I/P 1L7
93LC46B
0528
Example:
Example:
SN 0528
93LC46BI
1L7
1L7
L46B
I528
Example:
3
e
3
e
8-Lead Rotated SOIC
XXXXYYWW
XXXXXXXT
NNN
Example:
SN 0528
93L46BXI
1L7
3
e
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 14 2002-2011 Microchip Technology Inc.
Legend: XX...X Part number or part number code
T Temperature (I, E)
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note: For very small packages with no room for the Pb-free JEDEC designator
, the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
Part Number
1st Line Marking Codes
TSSOP MSOP
SOT-23 DFN TDFN
I Temp. E Temp. I Temp. E Temp. I Temp. E Temp.
93AA46A A46A 3A46AT 1BNN — 301 — E01 —
93AA46B A46B 3A46BT 1LNN — 311 — E11 —
93AA46C A46C 3A46CT — — 321 — E21 —
93LC46A L46A 3L46AT 1ENN 1FNN 304 — E04 E05
93LC46B L46B 3L46BT 1PNN 1RNN 314 — E14 E15
93LC46C L46C 3L46CT — — 324 — E24 —
93C46A C46A 3C46AT 1HNN 1JNN 307 — E07 E08
93C46B C46B 3C46BT 1TNN 1UNN 317 — E17 E18
93C46C C46C 3C46CT — — 327 — E27 —
Note: T = Temperature grade (I, E)
NN = Alphanumeric traceability code
8-Lead 2x3 DFN Example:
314
528
L7
XXX
YWW
NN
8-Lead 2x3 TDFN Example:
E14
528
L7
XXX
YWW
NN
2002-2011 Microchip Technology Inc. DS21749J-page 15
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
D
N
E
E1
NOTE 1
12
e
b
A
A1
A2 c
L1 L
φ
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 16 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 17
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
!"
b
E
4
N
E1
PIN1IDBY
LASER MARK
D
123
e
e1
A
A1
A2 c
L
L1
φ
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 18 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 19
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
#$%"&&'(#$
N
E1
NOTE 1
D
123
A
A1
A2
L
b1
b
e
E
eB
c
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 20 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 21
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 22 2002-2011 Microchip Technology Inc.
%)*"+,&'($-
2002-2011 Microchip Technology Inc. DS21749J-page 23
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
.. %/+/'(
D
N
E
E1
NOTE 1
12
b
e
c
A
A1
A2
L1 L
φ
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 24 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 25
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
#0*-%!1"1&+,'(#0
D
N
E
NOTE 1
12
EXPOSED PAD
NOTE 1
21
D2
K
L
E2
N
e
b
A3 A1
A
NOTE 2
BOTTOM VIEW
TOP VIEW
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 26 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 27
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 28 2002-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2011 Microchip Technology Inc. DS21749J-page 29
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
#0*%!1"1&+23'( #0
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 30 2002-2011 Microchip Technology Inc.
APPENDIX A: REVISION HISTORY
Revision D (12/2003)
Corrections to Section 1.0, Electrical Characteristics.
Section 4.1, 6-Lead SOT-23 package to OT.
Revision E (3/2005)
Added DFN package.
Revision F (4/2005)
Added notes throughout.
Revision G (5/2008)
Revised Figures 2-1 through 2-4 and Figures 2-8
through 2-11; Revised Package Marking Information;
Replaced Package Drawings; Revised Product ID
section.
Revision H (08/2010)
Added 8-Lead Rotated SOIC marking information;
Revised Package Drawings; Revised Product ID
System.
Revision J (12/2011)
Added TDFN Package.
2002-2011 Microchip Technology Inc. DS21749J-page 29
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
•Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
•General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
•Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Development Systems Information Line
Customers should contact their distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://microchip.com/support
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 30 2002-2011 Microchip Technology Inc.
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO: Technical Publications Manager
RE: Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
Application (optional):
Would you like a reply? Y N
Device: Literature Number:
Questions:
FAX: (______) _________ - _________
DS21749J93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
2002-2011 Microchip Technology Inc. DS21749J-page 31
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Device: 93AA46A: 1K 1.8V Microwire Serial EEPROM
93AA46B: 1K 1.8V Microwire Serial EEPROM
93AA46C: 1K 1.8V Microwire Serial EEPROM w/ORG
93LC46A: 1K 2.5V Microwire Serial EEPROM
93LC46B: 1K 2.5V Microwire Serial EEPROM
93LC46C: 1K 2.5V Microwire Serial EEPROM w/ORG
93C46A: 1K 5.0V Microwire Serial EEPROM
93C46B: 1K 5.0V Microwire Serial EEPROM
93C46C: 1K 5.0V Microwire Serial EEPROM w/ORG
Pinout: Blank = Standard pinout
X = Rotated pinout (SOIC only)
Tape & Reel: Blank = Standard packaging
T = Tape & Reel
Temperature Range: I = -40°C to +85°C
E = -40°C to +125°C
Package: MS = Plastic MSOP (Micro Small outline), 8-lead
OT = Plastic SOT-23, 6-lead (Tape & Reel only)
P = Plastic DIP (300 mil body), 8-lead
SN = Plastic SOIC (3.9 mm body), 8-lead
ST = Plastic TSSOP (4.4 mm body), 8-lead
MC = Plastic DFN (2x3x0.90 mm body), 8-lead
MNY(1) = Plastic TDFN (2x3x0.75 mm body), 8-lead
(Tape & Reel only)
Note 1: “Y” indicates a Nickel Palladium Gold (NiPdAu) finish.
Examples:
a) 93AA46C-I/P: 1K, 128x8 or 64x16 Serial
EEPROM, PDIP package, 1.8V
b) 93AA46B-I/MS: 1K, 64x16 Serial EEPROM,
MSOP package, 1.8V
c) 93AA46AT-I/OT: 1K, 128x8 Serial EEPROM,
SOT-23 package, tape and reel, 1.8V
d) 93AA46CT-I/SN: 1K, 128x8 or 16x16 Serial
EEPROM, SOIC package, tape and reel, 1.8V
a) 93LC46A-I/MS: 1K, 128x8 Serial EEPROM,
MSOP package, 2.5V
b) 93LC46BT-I/OT: 1K, 64x16 Serial EEPROM,
SOT-23 package, tape and reel, 2.5V
c) 93LC46B-I/ST: 1K, 64x16 Serial EEPROM,
TSSOP package, 2.5V
d) 93LC46CT-I/MNY: 1K, 128x8 or 64x16 Serial
EEPROM, TDFN package, tape and reel, 2.5V
a) 93C46B-I/MS: 1K, 64x16 Serial EEPROM,
MSOP package, 5.0V
b) 93C46C-I/MS: 1K, 128x8 or 64x16 Serial
EEPROM, MSOP package, 5.0V
c) 93C46AT-I/OT: 1K, 128x8 Serial EEPROM,
SOT-23 package, tape and reel, 5.0V
d) 93C46BX-I/SN: 1K, 64x16 Serial EEPROM,
Rotated SOIC Package, 5.0V
PART NO. X/XX
Package
Temperature
Range
Device
X
Lead Finish
X
Tape & Reel
X
Pinout
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749J-page 32 2002-2011 Microchip Technology Inc.
NOTES:
2002-2011 Microchip Technology Inc. DS21749J-page 33
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT,
chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2002-2011, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-61341-875-8
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS21749J-page 34 2002-2011 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-330-9305
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Worldwide Sales and Service
11/29/11
