ALD2724SBL - Advanced Linear Devices Inc

www.aldinc.com

GENERAL DESCRIPTION

The ALD2724E/ALD2724 is a dual monolithic operational amplifier with

MOSFET input that has rail-to-rail input and output voltage ranges. The

input voltage range and output voltage range are very close to the positive

and negative power supply voltages. Typically the input voltage can be

beyond positive power supply voltage V+ or the negative power supply

voltage V- by up to 300mV. The output voltage swings to within 60mV of

either positive or negative power supply voltages at rated load.

With high impedance load, the output voltage of the ALD2724E/ALD2724

approaches within 1mV of the power supply rails. This device is designed

as an alternative to the popular J-FET input operational amplifier in

applications where lower operating voltages, such as 9V battery or ±3.25V

to ±5V power supplies are being used. The ALD2724E/ALD2724 offers

high slew rate of 5.0V/µs.

The rail-to-rail input and output feature of the ALD2724E/ALD2724

expands signal voltage range for a given operating supply voltage and

allows numerous analog serial stages to be implemented without losing

operating voltage margin. The output stage is designed to drive up to

10mA into 400pF capacitive and 1.5KΩ resistive loads at unity gain and

up to 4000pF at a gain of 5. Short circuit protection to either ground or the

power supply rails is at approximately 15mA clamp current. Due to

complementary output stage design, the output can source and sink

10mA into a load with symmetrical drive and is ideally suited for applica-

tions where push-pull voltage drive is desired.

BENEFITS

• Ready-to-use off-the-shelf standard part

• Custom automated trimming optional

• Remote controlled automated trimming

• In-System Programming capability

• No external components

• No internal clocking noise source

• Simple and cost effective

• Small package size

• Extremely small total functional

volume size

• Low system implementation cost

APPLICATIONS

• Sensor interface circuits

• Transducer biasing circuits

• Capacitive and charge integration circuits

• Biochemical probe interface

• Signal conditioning

• Portable instruments

• High source impedance electrode

amplifiers

• Precision Sample and Hold amplifiers

• Precision current to voltage converter

• Error correction circuits

• Sensor compensation circuits

• Precision gain amplifiers

• Periodic In-system calibration

• System output level shifter

KEY FEATURES

• Factory pre-trimmed VOS

•V

OS=25µV @ IOS=0.01pA

• 5V/µs slew rate

• EPAD (Electrically Programmable Analog Device)

• User programmable VOS trimmer

• Rail-to-rail input/output

• Compatible with standard EPAD Programmer

• Each amplifier VOS can be trimmed to a different VOS level

• High precision through in-system circuit precision trimming

• Reduces or eliminates VOS, PSRR, CMRR and TCVOS errors

• System level “calibration” capability

• Low voltage operation

ORDERING INFORMATION

Operating Temperature Range

0°C to +70°C0°C to +70°C -55°C to +125°C

14-Pin 14-Pin 14-Pin

Small Outline Plastic Dip CERDIP

Package (SOIC) Package Package

ALD2724ESB ALD2724EPB ALD2724EDB

ALD2724SB ALD2724PB ALD2724DB

* Contact factory for high temperature versions.

EPAD

DUAL EPAD® PRECISION HIGH SLEW RATE CMOS OPERATIONAL AMPLIFIER

ALD2724E/ALD2724

DVANCED

INEAR

EVICES,

NC.

PIN CONFIGURATION

TOP VIEW

SB, PB, DB PACKAGES

* N/C Pins are internally connected. Do not connect externally.

OUT

V+

OUT

+IN

N/C

V-

+IN

-IN

N/C

-IN

ALD2724E/ALD2724 Advanced Linear Devices 2 of 13

FUNCTIONAL DESCRIPTION

The ALD2724E/ALD2724 uses EPADs as in-circuit ele-

ments for trimming of offset voltage bias characteristics.

Each ALD2724E/ALD2724 has a pair of EPAD-based cir-

cuits connected such that one circuit is used to adjust VOS in

one direction and the other circuit is used to adjust VOS in the

other direction. While each of the EPAD devices is a

monotonically adjustable programmable device, the VOS of

the ALD2724E can be adjusted many times in both direc-

tions. Once programmed, the set VOS levels are stored

permanently, even when the device power is removed.

Functional Description of ALD2724E

The ALD2724E is pre-programmed at the factory under

standard operating conditions for minimum equivalent input

offset voltage. It also has a guaranteed offset voltage

program range, which is ideal for applications that require

electrical offset voltage programming.

The ALD2724E is an operational amplifier that can be

trimmed with user application-specific programming or in-

system programming conditions. User application-specific

circuit programming refers to the situation where the Total

Input Offset Voltage of the ALD2724E can be trimmed with

the actual intended operating conditions.

For example, an application circuit may have +5V and -5V

power supplies, and the operational amplifier input is biased

at +1V, and an average operating temperature at +85°C.

The circuit can be wired up to these conditions within an

environmental chamber with the ALD2724E inserted into a

test socket connected to this circuit while it is being electri-

cally trimmed. Any error in VOS due to these bias conditions

can be automatically zeroed out. The Total VOS error is now

limited only by the adjustable range and the stability of VOS,

and the input noise voltage of the operational amplifier.

Therefore, this Total VOS error now includes VOS as VOS is

traditionally specified; plus the VOS error contributions from

PSRR, CMRR, TCVOS, and noise. Typically this total VOS

error (VOST) is approximately ±25µV for the ALD2724E.

In-System Programming refers to the condition where the

EPAD adjustment is made after the ALD2724E has been

inserted into a circuit board. In this case, the circuit design

must provide for the ALD2724E to operate in normal mode

and in programming mode. One of the benefits of in-system

programming is that not only is the ALD2724E offset voltage

from operating bias conditions accounted for, any residual

errors introduced by other circuit components, such as

resistor or sensor induced voltage errors, can also be cor-

rected. In this way, the “in-system” circuit output can be

adjusted to a desired level, eliminating the need for another

trimming function.

Functional Description of ALD2724

The ALD2724 is pre-programmed at the factory under stan-

dard operating conditions for minimum equivalent input off-

set voltage. The ALD2724 offers similar programmable

features as the ALD2724E, but with a more limited offset

voltage program range. In is intended for standard opera-

tional amplifier applications, where little or no electrical

porggramming by the user is necessary.

USER PROGRAMMABLE VOS FEATURE

Each ALD2724E/ALD2724 has four additional pins, com-

pared to a conventional dual operational amplifier which has

eight pins. These four additional pins are named VE1A,

VE2A for op amp A and VE1B, VE2B for op amp B. Each of

these pins VE1A, VE2A, VE1B, VE2B (represented by VExx)

are connected to a separate, internal offset bias circuit. VExx

pins have initial internal bias voltage values of approximately

1V to 2V. The voltage on these pins can be programmed

using the ALD E100 EPAD Programmer and the appropriate

Adapter Module. The useful programming range of voltages

on VExx pins are 1V to 4V.

VExx pins are programming pins, used during electrical

programming mode to inject charge into the internal EPADs.

Increasing voltage on VE1A/VE1B decreases the offset

voltage whereas increasing voltage on VE2A/VE2B in-

creases the offset voltage of op amp A and op amp B,

respectively. The injected charge is then permanently

stored. After programming, VExx pins must be left open in

order for these voltages to remain at the programmed levels.

During programming, voltages on VExx pins are increased

incrementally to program the offset voltage of the operational

amplifier to the desired VOS. Note that desired VOS can be

any value within the offset voltage programmable ranges,

and can be equal zero, a positive value or a negative value.

This VOS value can also be reprogrammed to a different

value at a later time, provided that the useful VE1x or VE2x

programming voltage range has not been exceeded. VExx

pins can also serve as capacitively coupled input pins.

Internally, VE1 and VE2 are programmed and connected

differentially. Temperature drift effects between the two

internal offset bias circuits cancel each other and introduce

less net temperature drift coefficient change than offset

voltage trimming techniques such as offset adjustment with

an external trimmer potentiometer.

While programming, V+, VE1 and VE2 pins may be alter-

nately pulsed with 12V (approximately) pulses generated by

the EPAD Programmer. In-system programming requires

the ALD2724E application circuit to accommodate these

programming pulses. This can be accomplished by adding

resistors at certain appropriate circuit nodes. For more

information, see Application Note AN1700.

ALD2724E/ALD2724 Advanced Linear Devices 3 of 13

Supply voltage, V+ 10.6V

Differential input voltage range -0.3V to V+ +0.3V

Power dissipation 600 mW

Operating temperature range SB, PB packages 0°C to +70°C

DB package -55°C to +125°C

Storage temperature range -65°C to +150°C

Lead temperature, 10 seconds +260°C

CAUTION: ESD Sensitive Device. Use static control procedures in ESD controlled environment.

ABSOLUTE MAXIMUM RATINGS

* NOTES 1 through 9, see section titled "Definitions and Design Notes".

2724E 2724

Parameter Symbol Min Typ Max Min Typ Max Unit Test Conditions

Supply Voltage VS±3.25 ±5.0 ±3.25 ±5.0 V Dual Supply

V+6.5 10.0 6.5 10.0 V Single Supply

Initial Input Offset Voltage1VOS i 25 100 40 150 µVR

≤ 100KΩ

Offset Voltage Program Range 2∆VOS ±5±7±0.5 ±2mV

Programmed Input Offset VOS 25 100 40 150 µV At user specified

Voltage Error3target offset voltage

Total Input Offset Voltage 4VOST 25 100 40 150 µV At user specified

target offset voltage

Input Offset Current 5IOS 0.01 10 0.01 10 pA TA = 25°C

240 240 pA 0°C ≤ TA ≤ +70°C

Input Bias Current 5IB0.01 10 0.01 10 pA TA = 25°C

240 240 pA 0°C ≤ TA ≤ +70°C

Input Voltage Range 6VIR -0.3 5.3 -0.3 5.3 V V+ = +5V

-2.8 +2.8 -2.8 +2.8 V VS = ±2.5V

Input Resistance RIN 1014 1014 Ω

Input Offset Voltage Drift 7TCVOS 55µV/°CR

S ≤ 100KΩ

Initial Power Supply PSRR i85 85 dB RS ≤ 100KΩ

Rejection Ratio 8

Initial Common Mode CMRR i90 90 dB RS ≤ 100KΩ

Rejection Ratio 8

Large Signal Voltage Gain AV150 150 V/mV RL =10KΩ

V/mV 0°C ≤ TA ≤ +70°C

VO low -4.998 -4.99 -4.998 -4.99 V RL =1MΩ V =5V

Output Voltage Range VO high 4.99 4.998 4.99 4.998 V 0°C ≤ TA ≤ +70°C

VO low -4.96 -4.90 -4.96 -4.90 V RL =100KΩ

VO high 4.90 4.95 4.90 4.95 V 0°C ≤ TA ≤ +70°C

Output Short Circuit Current ISC 15 15 mA

OPERATING ELECTRICAL CHARACTERISTICS

TA = 25oC VS = ±5.0V unless otherwise specified

ALD2724E/ALD2724 Advanced Linear Devices 4 of 13

OPERATING ELECTRICAL CHARACTERISTICS (cont'd)

* NOTES 1 through 9, see section titled "Definitions and Design Notes".

2724E 2724

Parameter Symbol Min Typ Max Min Typ Max Unit Test Conditions

Average Long Term Input Offset ∆ VOS 0.02 0.02 µV/

Voltage Stability 9∆ time 1000 hrs

Initial VE Voltage VE1 i, VE2 i1.4 2.5 V

Programmable Change of ∆VE1, ∆VE2 1.5 2.0 0.5 V

VE Range

Programmed VE Voltage Error e(VE1-VE2) 0.1 0.1 %

VE Pin Leakage Current ieb -5 -5 µA

TA = 25oC VS = ±5.0V unless otherwise specified

2724E 2724

Parameter Symbol Min Typ Max Min Typ Max Unit Test Conditions

Supply Current IS5.0 6.5 5.0 6.5 mA VIN = 0V

No Load

Power Dissipation PD65 65 mW VS = ±2.5V

Input Capacitance CIN 11

Maximum Load Capacitance CL 400 400 pF Gain = 1

4000 4000 pF Gain = 5

Equivalent Input Noise Voltage en26 26 nV/√Hz f = 1KHz

Equivalent Input Noise Current in0.6 0.6 fA/√Hz f =10Hz

Bandwidth BW2.1 2.1 MHz

Slew Rate SR5.0 5.0 V/µsA

= +1

RL = 2KΩ

Rise time tr0.1 0.1 µsR

L = 2KΩ

Overshoot Factor 15 15 % RL=2KΩ

CL=100pF

Settling Time tS22µs 0.1% AV = -1

RL= 5KΩ

CL = 50pF

Channel Separation CS 140 140 dB AV = 100

TA = 25oC VS = ±5.0V unless otherwise specified

ALD2724E/ALD2724 Advanced Linear Devices 5 of 13

OPERATING ELECTRICAL CHARACTERISTICS (cont'd)

2724E 2724

Parameter Symbol Min Typ Max Min Typ Max Unit Test Conditions

Initial Input offset Voltage VOS i 0.7 0.7 mV RS ≤ 100KΩ

Input Offset Current IOS 2.0 2.0 nA

Input Bias Current IB2.0 2.0 nA

Initial Power Supply PSRR i85 85 dB RS ≤ 100KΩ

Rejection Ratio 8

Initial Common Mode CMRR i97 97 dB RS ≤ 100KΩ

Rejection Ratio 8

Large Signal Voltage Gain AV10 25 10 25 V/mV RL = 10KΩ

Output Voltage Range VO low -4.9 -4.8 -4.9 -4.8 V

VO high 4.8 4.9 4.8 4.9 V RL = 10KΩ

VS = ±5.0V -55°C ≤ TA ≤ +125°C unless otherwise specified

ALD2724E/ALD2724 Advanced Linear Devices 6 of 13

DEFINITIONS AND DESIGN NOTES:

1. Initial Input Offset Voltage is the initial offset voltage of the

ALD2724E/ALD2724 operational amplifier when shipped from

the factory. The device has been pre-programmed and tested

for programmability.

2. Offset Voltage Program Range is the range of adjustment of

user specified target offset voltage. This is typically an adjust-

ment in either the positive or the negative direction of the input

offset voltage from an initial input offset voltage. The input offset

programming pins, VE1A/VE1B or VE2A/VE2B, change the

input offset voltage in the negative or positive direction, for each

of the amplifiers, A or B respectively. User specified target offset

voltage can be any offset voltage within this programming

range.

3. Programmed Input Offset Voltage Error is the final offset

voltage error after programming when the Input Offset Voltage

is at target Offset Voltage. This parameter is sample tested.

4. Total Input Offset Voltage is the same as Programmed Input

Offset Voltage, corrected for system offset voltage error. Usu-

ally this is an all inclusive system offset voltage, which also

includes offset voltage contributions from input offset voltage,

PSRR, CMRR, TCVOS and noise. It can also include errors

introduced by external components, at a system level. Pro-

grammed Input Offset Voltage and Total Input Offset Voltage is

not necessarily zero offset voltage, but an offset voltage set to

compensate for other system errors as well. This parameter is

sample tested.

5. The Input Offset and Bias Currents are essentially input

protection diode reverse bias leakage currents. This low input

bias current assures that the analog signal from the source will

not be distorted by it. For applications where source impedance

is very high, it may be necessary to limit noise and hum pickup

through proper shielding.

6. Input Voltage Range is determined by two parallel comple-

mentary input stages that are summed internally, each stage

having a separate input offset voltage. While Total Input Offset

Voltage can be trimmed to a desired target value, it is essential

to note that this trimming occurs at only one user selected input

bias voltage. Depending on the selected input bias voltage

relative to the power supply voltages, offset voltage trimming

may affect one or both input stages. For the ALD2724E/

ALD2724, the switching point between the two stages occurs at

approximately 1.5V above negative supply voltage.

7. Input Offset Voltage Drift is the average change in Total Input

Offset Voltage as a function of ambient temperature. This

parameter is sample tested.

8. Initial PSRR and initial CMRR specifications are provided as

reference information. After programming, error contribution to

the offset voltage from PSRR and CMRR is set to zero under the

specific power supply and common mode conditions, and

becomes part of the Programmed Input Offset Voltage Error.

9. Average Long Term Input Offset Voltage Stability is based on

input offset voltage shift through operating life test at 125°C

extrapolated to TA = 25°C, assuming activation energy of 1.0eV.

This parameter is sample tested.

ADDITIONAL DESIGN NOTES:

A. The ALD2724E/ALD2724 is internally compensated for

unity gain stability using a novel scheme which produces a single

pole role off in the gain characteristics while providing more than

70 degrees of phase margin at unity gain frequency. A unity gain

buffer using the ALD2724E/ALD2724 will typically drive 400pF

of external load capacitance.

B. The ALD2724E/ALD2724 has complementary p-channel

and n-channel input differential stages connected in parallel to

accomplish rail-to-rail input common mode voltage range. The

switching point between the two differential stages is 1.5V above

negative supply voltage. For applications such as inverting

amplifiers or non-inverting amplifiers with a gain larger than 2.5

(5V operation), the common mode voltage does not make

excursions below this switching point. However, this switching

does take place if the operational amplifier is connected as a rail-

to-rail unity gain buffer and the design must allow for input offset

voltage variations.

C. The output stage consists of class AB complementary output

drivers. The oscillation resistant feature, combined with the rail-

to-rail input and output feature, makes the ALD2724E/

ALD2724 an effective analog signal buffer for high source

impedance sensors, transducers, and other circuit networks.

D. The ALD2724E/ALD2724 has static discharge protection.

However, care must be exercised when handling the device to

avoid strong static fields that may degrade a diode junction,

causing increased input leakage currents. The user is advised

to power up the circuit before, or simultaneously with, any input

voltages applied and to limit input voltages not to exceed 0.3V of

the power supply voltage levels.

E. VExx are high impedance terminals, as the internal bias

currents are set very low to a few microamperes to conserve

power. For some applications, these terminals may need to be

shielded from external coupling sources. For example, digital

signals running nearby may cause unwanted offset voltage

fluctuations. Care during the printed circuit board layout, to

place ground traces around these pins and to isolate them from

digital lines, will generally eliminate such coupling effects. In

addition, optional decoupling capacitors of 1000pF or greater

value can be added to VExx terminals.

F. The ALD2724E/ALD2724 is designed for use in low voltage,

micropower circuits. The maximum operating voltage during

normal operation should remain below 10V at all times. Care

should be taken to insure that the application in which the device

is used does not experience any positive or negative transient

voltages that will cause any of the terminal voltages to exceed

this limit.

G. All inputs or unused pins except VExx pins should be

connected to a supply voltage such as Ground so that they do not

become floating pins, since input impedance at these pins is very

high. If any of these pins are left undefined, they may cause

unwanted oscillation or intermittent excessive current drain. As

these devices are built with CMOS technology, normal operating

and storage temperature limits, ESD and latchup handling

precautions pertaining to CMOS device handling should be

observed.

ALD2724E/ALD2724 Advanced Linear Devices 7 of 13

TYPICAL PERFORMANCE CHARACTERISTICS

ADJUSTMENT IN INPUT OFFSET VOLTAGE

AS A FUNCTION OF CHANGE IN VE1 AND VE2

CHANGE IN INPUT OFFSET

VOLTAGE ∆V

(mV)

0 0.5 1.0 1.5 2.0 2.5 3.0

-10

-8

-6

-4

-2

VE2

VE1

CHANGE IN VE1 AND VE2 (V)

INPUT BIAS CURRENT AS A FUNCTION

OF AMBIENT TEMPERATURE

AMBIENT TEMPERATURE (°C)

1000

100

0.1

1.0

INPUT BIAS CURRENT (pA)

100-25 0 75 1255025-50

= ±5.0V

10000

SUPPLY CURRENT AS A FUNCTION

OF SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

SUPPLY CURRENT (mA)

0±1±2±3±4±5±6

INPUTS GROUNDED

OUTPUT UNLOADED

+80°C

+25°C

= -55°C

-25°C

±7

+125°C

OPEN LOOP VOLTAGE GAIN AS A FUNCTION

OF SUPPLY VOLTAGE AND TEMPERATURE

SUPPLY VOLTAGE (V)

1000

100

OPEN LOOP VOLTAGE

GAIN (V/mV)

0 ±2 ±4 ±6

= 10KΩ

= 5KΩ

}

-55°C

}

+25°C

}

+125°C

±8

COMMON MODE INPUT VOLTAGE RANGE

AS A FUNCTION OF SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

COMMON MODE INPUT

VOLTAGE RANGE (V)

±7

±6

±5

±4

±3

±2±2 ±3 ±4 ±5 ±6 ±7

= 25°C

OPEN LOOP VOLTAGE GAIN AS

A FUNCTION OF FREQUENCY

FREQUENCY (Hz)

1 10 100 1K 10K 1M 10M100K

120

100

-20

OPEN LOOP VOLTAGE

GAIN (dB)

= ±5.0V

= 25°C

180

135

PHASE SHIFT IN DEGREES

ALD2724E/ALD2724 Advanced Linear Devices 8 of 13

TYPICAL PERFORMANCE CHARACTERISTICS (cont'd)

-2500 -2000 -1500 -1000 -500 0500 1000 1500 2000 2500

TOTAL INPUT OFFSET VOLTAGE (µV)

100

DISTRIBUTION OF TOTAL INPUT OFFSET VOLTAGE

BEFORE AND AFTER EPAD PROGRAMMING

EXAMPLE B:

OST

AFTER EPAD

PROGRAMMING

OST

TARGET = -750µV

EXAMPLE A:

OST

AFTER EPAD

PROGRAMMING

OST

TARGET = 0.0µV

OST

BEFORE EPAD

PROGRAMMING

PERCENTAGE OF UNITS (%)

RL = 10KΩ

OUTPUT VOLTAGE SWING AS A

FUNCTION OF SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

OUTPUT VOLTAGE SWING (V)

±3

0±1±2±3±4±5±6±7

= 2KΩ

±6

±5

±4

±2

±7

-55°C ≤ T

≤ 125°C

= 10KΩ

OPEN LOOP VOLTAGE GAIN AS A

FUNCTION OF LOAD RESISTANCE

LOAD RESISTANCE (Ω)

1K 10K 1000K100K

1000

100

OPEN LOOP VOLTAGE

GAIN (V/mV)

= ±5.0V

= 25°C

SMALL - SIGNAL TRANSIENT

RESPONSE

= ± 5.0V

= 25°C

= 1.0KΩ

= 50pF

100mV/div

50mV/div 1µs/div

LARGE - SIGNAL TRANSIENT

RESPONSE

= ±5.0V

= 25°C

= 1KΩ

= 50pF

5V/div

5V/div 2µs/div

ALD2724E/ALD2724 Advanced Linear Devices 9 of 13

0123456789 10

500

400

300

200

100

EQUIVALENT INPUT OFFSET VOLTAGE DUE TO

CHANGE IN SUPPLY VOLTAGE (µV)

TWO EXAMPLES OF EQUIVALENT INPUT OFFSET VOLTAGE DUE TO

CHANGE IN SUPPLY VOLTAGE vs. SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

PSRR = 80 dB

EXAMPLE B:

EPAD

PROGRAMMED

AT V

SUPPLY

= +8V

EXAMPLE A:

EPAD PROGRAMMED

AT V

SUPPLY

= +5V

-5 -4 -3 -2 -1 012345

COMMON MODE VOLTAGE (V)

500

400

300

200

100

EQUIVALENT INPUT OFFSET VOLTAGE DUE TO

CHANGE IN COMMON MODE VOLTAGE (µV)

EXAMPLE A:

EPAD PROGRAMMED

AT V

= 0V

EXAMPLE B:

EPAD

PROGRAMMED

AT V

= -4.3V

EXAMPLE C:

EPAD PROGRAMMED

AT V

= +5V

SUPPLY

= ±5V

CMRR = 80dB

THREE EXAMPLES OF EQUIVALENT INPUT OFFSET VOLTAGE DUE TO

CHANGE IN COMMON MODE VOLTAGE vs. COMMON MODE VOLTAGE

-0.5 -0.4 -0.3 -0.2 -0.1 0.0 0.1 0.2 0.3 0.4 0.5

COMMON MODE VOLTAGE (V)

EQUIVALENT INPUT OFFSET VOLTAGE DUE TO

CHANGE IN COMMON MODE VOLTAGE (µV)

EPAD

PROGRAMMED

AT COMMON MODE

VOLTAGE OF 0.25V

CMRR = 80dB

EXAMPLE OF MINIMIZING EQUIVALENT INPUT OFFSET VOLTAGE

FOR A COMMON MODE VOLTAGE RANGE OF 0.5V

COMMON MODE VOLTAGE RANGE OF 0.5V

TYPICAL PERFORMANCE CHARACTERISTICS (cont'd)

ALD2724E/ALD2724 Advanced Linear Devices 10 of 13

Total Input V

after EPAD

Programming

Device input V

PSRR equivalent V

CMRR equivalent V

equivalent V

Noise equivalent V

External Error equivalent V

EXAMPLE A

TOTAL INPUT OFFSET VOLTAGE (µV)

2500

2000

1500

1000

500

0

-500

-1000

-1500

-2000

-2500

BUDGET BEFORE

EPAD PROGRAMMING

BUDGET AFTER

EPAD PROGRAMMING

EXAMPLE B

TOTAL INPUT OFFSET VOLTAGE (µV)

2500

2000

1500

1000

500

0

-500

-1000

-1500

-2000

-2500

BUDGET BEFORE

EPAD PROGRAMMING

BUDGET AFTER

EPAD PROGRAMMING

EXAMPLE C

TOTAL INPUT OFFSET VOLTAGE (µV)

2500

2000

1500

1000

500

0

-500

-1000

-1500

-2000

-2500

BUDGET BEFORE

EPAD PROGRAMMING

BUDGET AFTER

EPAD PROGRAMMING

EXAMPLE D

TOTAL INPUT OFFSET VOLTAGE (µV)

2500

2000

1500

1000

500

0

-500

-1000

-1500

-2000

-2500

BUDGET AFTER

EPAD PROGRAMMING

BUDGET BEFORE

EPAD PROGRAMMING

APPLICATION SPECIFIC / IN-SYSTEM PROGRAMMING

Examples of applications where accumulated total input offset voltage from various

contributing sources is minimized under different sets of user-specified operating conditions

TYPICAL PERFORMANCE CHARACTERISTICS (cont'd)

ALD2724E/ALD2724 Advanced Linear Devices 11 of 13

Millimeters Inches

Min Max Min MaxDim

D-14

1.75

0.25

0.45

0.25

8.75

4.05



6.30

0.937

8°

0.50

0.053

0.004

0.014

0.007

0.336

0.140



0.224

0.024

0°

0.010



0.069

0.010

0.018

0.010

0.345

0.160



0.248

0.037

8°

0.020

1.27 BSC 0.050 BSC

1.35

0.10

0.35

0.18

8.55

3.50

5.70

0.60

0°

0.25

14 Pin Plastic SOIC Package

SOIC-14 PACKAGE DRAWING

S (45°)

ALD2724E/ALD2724 Advanced Linear Devices 12 of 13

14 Pin Plastic DIP Package

PDIP-14 PACKAGE DRAWING

EE1

Millimeters Inches

Min Max Min MaxDim

D-14

S-14

3.81

0.38

1.27

0.89

0.38

0.20

17.27

5.59

7.62

2.29

7.37

2.79

1.02

0°

5.08

1.27

2.03

1.65

0.51

0.30

19.30

7.11

8.26

2.79

7.87

3.81

2.03

15°

0.105

0.015

0.050

0.035

0.015

0.008

0.680

0.220

0.300

0.090

0.290

0.110

0.040

0°

0.200

0.050

0.080

0.065

0.020

0.012

0.760

0.280

0.325

0.110

0.310

0.150

0.080

15°

ALD2724E/ALD2724 Advanced Linear Devices 13 of 13

D-14

3.55

1.27

0.97

0.36

0.20

--

5.59

7.73



3.81

3.18

0.38

--

0°

5.08

2.16

1.65

0.58

0.38

19.94

7.87

8.26



5.08

--

1.78

2.49

15°

Millimeters Inches

Min Max Min MaxDim 0.140

0.050

0.038

0.014

0.008

--

0.220

0.290



0.150

0.125

0.015

--

0°

0.200

0.085

0.065

0.023

0.015

0.785

0.310

0.325



0.200

--

0.070

0.098

15°

2.54 BSC

7.62 BSC

0.100 BSC

0.300 BSC

14 Pin CERDIP Package

CERDIP-14 PACKAGE DRAWING