HAS030ZJ-A81V - Power-One

• Industry standard half-brick

• Low-cost design

• 100°C baseplate operation

• Open-frame packaging

• 24V and 48V input versions

• Input Pi filter

• Optional enable logic

• 1500V isolation

Features

HAS dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. With a

maximum case temperature of 100°C, the HAS is well suited for the most demanding telecom, networking, and

industrial applications. The HAS features 1500 VDC isolation, short circuit, and overtemperature protection, as well

as six-sided shielding. The HAS series is available with optional enable and voltage trim pins. Please see the HAD

Series for dual-output applications.

Description

Technical Specifications

Voltage Range

24 VDC Nominal 18 - 36 VDC

48 VDC Nominal 36 - 75 VDC

Transient 100V/100ms

Reflected Ripple 50 mA

Input

Setpoint Accuracy ±1%

Line Regulation Vin Min. - Vin Max., Iout Rated 0.2% Vout

Load Regulation Iout Min. - Iout Max., Vin Nom. 0.2% Vout

Remote Sense Headroom 0.5 VDC

Minimum Output Current 10 %

Dynamic Regulation, Loadstep 25% Iout

Pk Deviation 4% Vout

Settling Time 500 µs

Voltage Trim Range ±10%

Short Circuit / Overcurrent Protection Hiccup

Current Limit Threshold Range, % of Iout Rated 110 - 140%

OVP Trip Range 115 - 140% Vout Nom.

Remote Shutdown Reference Vin Negative

Shutdown Pin Current, Sourced At Off 10 mA Max.

Output

General

Turn-On Time 10 ms

Remote Shutdown Positive/Negative Logic

Switching Frequency 250 kHz

Isolation

Input - Output 1500 VDC

Input - Case 1050 VDC

Output - Case 500 VDC

Temperature Coefficient 0.03%/°C

Case Temperature

Operating Range -40 To +100°C

Storage Range -40 To +125°C

Humidity Max., Non-Condensing 95%

Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz

MTBF†(Bellcore TR-NWT-000332) 2.5 X 106hrs

Safety UL, cUL, TUV

Weight (Approx.) 1.4 oz

10 20 30 40 50 60 70 80 90 100

LOAD %

EFFICIENCY %

HAS030ZH-A

HAS030ZG-A

HAS030ZJ-A

HAS030YG-A

10 20 30 40 50 60 70 80 90 100

LOAD %

EFFICIENCY %

EFF. (18v)

EFF. (24v)

EFF. (36v)

Efficiency vs. Load (48V Input)

Efficiency vs. Load (24V Input)

Notes

†MTBF predictions may vary slightly from model to model.

Specifications typically at 25°C, normal line, and full load, unless

otherwise stated.

Soldering Conditions: I/O pins, 260°C, ten seconds; fully

compatible with commercial wave-soldering equipment.

Safety: Agency approvals may vary from model to model. Please

consult factory for specific model information.

Units are water-washable and fully compatible with commercial spray or

immersion post wave-solder washing equipment.

Page 1 of 3

HAS30 DC-DC Series Data Sheet

REV. JUN 03, 2004

MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL

(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**

HAS030YG-A 24 18-36 2.2 5 6.0 100 83%

HAS030YH-A 24 18-36 2.2 12 2.5 150 87%

HAS030YJ-A 24 18-36 2.2 15 2.0 150 86%

HAS030ZE-AT 48 36-75 1.0 3.3 6.0 100 81%

HAS030ZG-A 48 36-75 1.3 5 6.0 100 83%

HAS030ZH-A 48 36-75 1.3 12 2.5 150 88%

HAS030ZJ-A 48 36-75 1.3 15 2.0 150 88%

NOTES:

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal Vin, rated output.

Model Selection

Mechanical Drawing

0.700"(17.8mm)

1.400"(35.6mm)

1.000"(25.4mm)

0.400"(10.2mm)

0.18"

2.28"

(57.9mm)

DIA 0.040"

0.025" REF.

0.50"

(12.7mm)

(4.6mm)

(1.0mm)

MOUNTING INSERTS

M3X.5 THROUGH 4PL

(0.6mm)

BOTTOM VIEW

1.700"(43.2mm)

-0.50"(-12.7mm)

-0.300"(-7.6mm) -0.300"(-7.6mm)

1.400"(35.6mm)

1.000"(25.4mm)

0.400"(10.2mm)

(-4.8mm)

-0.19"

(48.3mm)

1.900"

(61.0mm)

2.40

Thermal Impedance

Natural Convection 7.9 °C/W

100 LFM 6.8 °C/W

200 LFM 4.9 °C/W

300 LFM 3.6 °C/W

400 LFM 3.0 °C/W

Tolerances

Note:

Thermal impedance data is

dependent on many environmental

factors. The exact thermal

performance should be validated

for specific application.

1-V

2 Case

3 On/Off

4+V

5-V

out

6 -Sense

7 Trim

8 +Sense

9+V

out

Inches: (Millimeters)

.XX ± 0.020 .X ± 0.5

.XXX ± 0.010 .XX ± 0.25

Pin:

± 0.002 ± 0.05

(Dimensions as listed unless

otherwise specified.)

Pin Function

Page 2 of 3

HAS30 DC-DC Series Data Sheet

REV. JUN 03, 2004

Model numbers highlighted in yellow or shaded are not recommended for new designs.

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, TTL "Low" Turns Module ON

QBS, QES, QLS, TES, TQD TTL "High" Turns Module OFF

Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Trim 1 IAS, LES

Enable 2 IAD, IAS, LES, SMS

Trim and Enable 3 IAS, LES

Pin Length and Heatsink Options Standard Pin Length is 0.180" (4.6mm)

0.110" (2.8mm) Pin Length 8 All Leaded Models

0.150" (3.8mm) Pin Length 9 All Leaded Models

0.24" (6.1mm) Horizontal Heatsink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad