1
D2T Door Interlock Switch
Compact DPST-NO Door Switch
■Incorporates two circuits for power loads and
micro loads. Micro load circuit uses twin contacts.
■Compact size, with an operating force of only
3.24 N {330 gf}.
■Panel- or screw-mounted with ease.
Ordering Information
■Model Number Legend
1. Actuator
None: Pin plunger
L: Hinge lever
2. Terminals
None: Right-angled solder terminals
S: Straight solder terminals
■List of Models
Note: The actuator of the D2T is identical to that used for OMRON’s V Snap-action Switches. The actuator can be replaced with other
types of actuators. Consult your OMRON sales representatives for details.
RoHS Compliant
RCW
D2T-@T1@
1 2
Actuator (see note) Right-angled solder terminals Straight solder terminals
D2T-T1 D2T-T1S
D2T-LT1 D2T-LT1S
Pin plunger
Hinge lever
2
D2TD2T
Specifications
■Ratings
Note: The ratings values apply under the following trest conditions:
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Operating frequency: 30 operations/min
■Characteristics
Note: 1. The data given above are initial values.
2. The dielectric strength shown in the table indicates a value for models with a Separator.
3. For the pin plunger models, the above values apply for use at both the free position and total travel position. For the lever models,
they apply at the total travel position. Contact opening or closing time is within 1 ms.
4. For testing conditions, consult your OMRON sales representative.
Rated voltage Resistive load
Between terminals 1 and 2 250 VAC 5 A
Between terminals 3 and 4 125 VAC 0.1 A
Operating speed 10 mm to 500 mm/s (pin plunger models)
Operating frequency Mechanical: 120 operations/min max.
Electrical: 30 operations/min max.
Insulation resistance 100 MΩ min. (at 500 VDC)
Contact resistance (initial value) Between terminals 1 and 2: 50 mΩ max.
Between terminals 3 and 4: 100 mΩ max.
Dielectric strength (see note 2) 1,000 VAC for 1 min 50/60 Hz between terminals of same polarity
1,500 VAC for 1 min 50/60 Hz between current-carrying metal part and ground (see note 1), be-
tween each terminal and non-current-carrying metal part, and between terminals of different po-
larity
Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance (see note 3) Destruction: 1,000 m/s2 {approx. 100G} max.
Malfunction: 300 m/s2 {approx. 30G} max.
Durability (see note 4) Mechanical: 100,000 operations min. (60 operations/min)
Electrical: 100,000 operations min. (30 operations/min)
Degree of protection IEC IP40
Degree of protection against electric
shock
Class I
Proof tracking index (PTI) 175
Ambient operating temperature –25°C to 85°C (at ambient humidity of 60% max.) (with no icing or condensation)
Ambient operating humidity 85% max. (for 5°C to 35°C)
Weight Approx. 10 g (pin plunger models)
3
D2TD2T
■Approved Standards
Consult your OMRON sales representative for specific models
with standard approvals.
UL1054 (File No. E41515)/
CSA C22.2 No. 55 (File No. LR21642)
EN61058-1 (File No. 120144, VDE approval)
Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C)
■Contact Specifications
■Contact Form
Note: The circuit switching power loads has a snap-action
mechanism and the circuit switching micro loads has a
slow-action mechanism.
Dimensions
Note: All units are in millimeters unless otherwise indicated.
■Terminals
Rated voltage Between termi-
nals 1 and 2
Between termi-
nals 3 and 4
125 VAC 5 A 0.1 A (for 100,000
operations)
250 VAC 5 A ---
Rated voltage Between termi-
nals 1 and 2
Between termi-
nals 3 and 4
125 VAC --- 0.1 A
250 VAC 5 A ---
Item Between ter-
minals 1 and 2
Between ter-
minals 3 and 4
Contact Specification Rivet Plated
Material Silver
Gap
(standard value)
1 mm 1.4 mm
Inrush current 60 A max. ---
Minimum applicable load 160 mA at
5 VDC
1 mA at 5 VDC
COM
Terminal 1
COM
Terminal 3
NO
Terminal 4
NO
Terminal
2
Micro load
Power load
DPST-NO
Solder terminal
t=0.5
1.2-dia.
hole
Solder terminal
t=0.5 1.2-dia. hole
2.6-dia. hole
2.6-dia. hole
Angled Terminals Straight Terminals
2.8±0.1
7.1±0.1
1
2.8±0.1
7.1±0.1
4
D2TD2T
■Mounting Holes
■Dimensions and Operating Characteristics
Note: 1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
3. The following illustrations and dimensions are for D2T models with angled terminals. Refer to the dimensions in Terminals for
the straight terminals of the D2T.
4. The operating characteristics are for operation in the A direction ( ).
Two, M3 screw holes
26.4±0.1
Panel Cutout Dimensions
(Panel thickness: 1.5 to 2 mm)
Four, 0.5R max.
11.9
+0.2
−0
31.0
+0.2
−0
D2T-T1
D2T-T1S
t=0.5
Solder terminal
2.6
hole
Two, 2.5R
1.2 hole
3.1+0.13
−0.03 dia. holes
3.4±0.15 dia.
26.4±0.15
2.8±0.1
15.35±0.2
Note: Operating sequence of the circuit
between terminals 1 and 2 and the
circuit between terminals 3 and 4 is
not specified.
A
Pin Plunger Models OF max.
RF min.
TTF max.
3.24 N {330 gf}
0.5 N {50 gf}
6.37 N {650 gf}
OT min. 0.8 mm
OP 4.4±0.6 mm
(see note)
Hinge Lever Models
D2T-LT1
D2T-LT1S
t=0.5
Solder terminal
t = 0.5
(Stainless-
steel lever)
30.9±0.8
Note: Operating sequence of the circuit
between terminals 1 and 2 and the
circuit between terminals 3 and 4 is
not s
p
ecified.
AOF max.
RF min.
TTF max.
1.47N {150gf}
0.20N {20gf}
2.45N {250gf}
OT min. 1.6 mm
FP max.
OP
RP max.
TTP max.
10.1mm
6.9±1.3mm
(see note)
9.5mm
3.6mm
5
D2TD2T
Precautions
Refer to General Information.
■Correct Use
Mounting
Apply operation force to the pin plunger in the direction it oper-
ates.
Applying forces laterally or from an oblique direction may damage
the pin plunger.
Use M3 mounting screws to mount the Switch. Tighten the
screws to a torque of 0.4 to 0.6 N·m {4 to 6 kgf·cm}.
Mounting Holes
When mounting on a metal surface, be sure to provide a Separa-
tor between the Switch and mounting plate.
Soldering
When soldering the lead wire to the terminal, first insert the lead
wire conductor through the terminal hole and the conduct solder-
ing.
Make sure that the temperature at the tip of soldering iron is
350°C max. Do not take more than 3 seconds to solder the switch
terminal, and do not impose external force on the terminal for 1
min after soldering. Improper soldering involving an excessively
high temperature or excessive solding time may deteriorate the
characteristics of the Switch.
IncorrectIncorrectCorrect
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. B097-E1-03
