LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
Check for Samples: LM193-N,LM2903-N,LM293-N,LM393-N
1FEATURES DESCRIPTION
The LM193 series consists of two independent
2 Wide Supply precision voltage comparators with an offset voltage
Voltage Range: 2.0V to 36V specification as low as 2.0 mV max for two
Single or Dual Supplies: ±1.0V to ±18V comparators which were designed specifically to
operate from a single power supply over a wide range
Very Low Supply Current Drain (0.4 mA) of voltages. Operation from split power supplies is
Independent of Supply Voltage also possible and the low power supply current drain
Low Input Biasing Current: 25 nA is independent of the magnitude of the power supply
Low Input Offset Current: ±5 nA voltage. These comparators also have a unique
characteristic in that the input common-mode voltage
Maximum Offset voltage: ±3 mV range includes ground, even though operated from a
Input Common-Mode Voltage Range Includes single power supply voltage.
Ground Application areas include limit comparators, simple
Differential Input Voltage Range Equal to the analog to digital converters; pulse, squarewave and
Power Supply Voltage time delay generators; wide range VCO; MOS clock
Low Output Saturation Voltage: 250 mV at 4 timers; multivibrators and high voltage digital logic
mA gates. The LM193 series was designed to directly
interface with TTL and CMOS. When operated from
Output Voltage Compatible with TTL, DTL, both plus and minus power supplies, the LM193
ECL, MOS and CMOS logic systems series will directly interface with MOS logic where
Available in the 8-Bump (12 mil) DSBGA their low power drain is a distinct advantage over
Package standard comparators.
See AN-1112 (SNVA009) for DSBGA The LM393 and LM2903 parts are available in TI’s
Considerations innovative thin DSBGA package with 8 (12 mil) large
bumps.
ADVANTAGES
High Precision Comparators
Reduced VOS Drift Over Temperature
Eliminates Need for Dual Supplies
Allows Sensing Near Ground
Compatible with All Forms of Logic
Power Drain Suitable for Battery Operation
Figure 1. Squarewave Oscillator Figure 2. Non-Inverting Comparator with
Hysteresis
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1999–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
Schematic and Connection Diagrams
Figure 3. Schematic
Figure 4. TO-99 Package Figure 5. CDIP, PDIP, SOIC Packages
Figure 6. DSBGA Top View
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
Absolute Maximum Ratings(1)(2)
Supply Voltage, V+36V
Differential Input Voltage (3) 36V
Input Voltage 0.3V to +36V
Input Current (VIN<0.3V) (4) 50 mA
Power Dissipation (5)
PDIP 780 mW
TO-99 660 mW
SOIC Package 510 mW
DSBGA Package 568mW
Output Short-Circuit to Ground (6) Continuous
Operating Temperature Range
LM393 0°C to +70°C
LM293 25°C to +85°C
LM193/LM193A 55°C to +125°C
LM2903 40°C to +85°C
Storage Temperature Range 65°C to +150°C
Lead Temperature (Soldering, 10 seconds) +260°C
Soldering Information
CDIP, PDIP Package Soldering (10 seconds) 260°C
SOIC Package 215°C
Vapor Phase (60 seconds)
Infrared (15 seconds) 220°C
See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices.
ESD rating (1.5 kΩin series with 100 pF) 1300V
(1) Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than 0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
(4) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the comparators to go
to the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive
and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than 0.3V.
(5) For operating at high temperatures, the LM393 and LM2903 must be derated based on a 125°C maximum junction temperature and a
thermal resistance of 170°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The
LM193/LM193A/LM293 must be derated based on a 150°C maximum junction temperature. The low bias dissipation and the “ON-OFF”
characteristic of the outputs keeps the chip dissipation very small (PD100 mW), provided the output transistors are allowed to saturate.
(6) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 20 mA independent of the magnitude of V+.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
Electrical Characteristics
(V+=5V, TA= 25°C, unless otherwise stated) LM193A
Parameter Test Conditions Units
Min Typ Max
Input Offset Voltage (1) 1.0 2.0 mV
Input Bias Current IIN(+) or IIN() with Output In Linear 25 100 nA
Range, VCM = 0V (2)
Input Offset Current IIN(+)IIN() VCM = 0V 3.0 25 nA
Input Common Mode Voltage Range V+ = 30V (3) 0 V+1.5 V
Supply Current RL=V+=5V 0.4 1 mA
V+=36V 1 2.5 mA
Voltage Gain RL15 kΩ, V+=15V 50 200 V/mV
VO= 1V to 11V
Large Signal Response Time VIN=TTL Logic Swing, VREF=1.4V 300 ns
VRL=5V, RL=5.1 kΩ
Response Time VRL=5V, RL=5.1 kΩ(4) 1.3 μs
Output Sink Current VIN()=1V, VIN(+)=0, VO1.5V 6.0 16 mA
Saturation Voltage VIN()=1V, VIN(+)=0, ISINK4 mA 250 400 mV
Output Leakage Current VIN()=0, VIN(+)=1V, VO=5V 0.1 nA
(1) At output switch point, VO1.4V, RS=0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+1.5V), at 25°C.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+1.5V at 25°C, but either or both inputs can go to 36V without damage, independent of the
magnitude of V+.
(4) The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
Typical Performance Characteristics.
Electrical Characteristics
(V+=5V, TA= 25°C, unless otherwise stated) LM193 LM293, LM393 LM2903
Parameter Test Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage (1) 1.0 5.0 1.0 5.0 2.0 7.0 mV
Input Bias Current IIN(+) or IIN() with Output In 25 100 25 250 25 250 nA
Linear Range, VCM = 0V (2)
Input Offset Current IIN(+)IIN() VCM = 0V 3.0 25 5.0 50 5.0 50 nA
Input Common Mode V+ = 30V (3) 0 V+1.5 0 V+1.5 0 V+1.5 V
Voltage Range
Supply Current RL=V+=5V 0.4 1 0.4 1 0.4 1.0 mA
V+=36V 1 2.5 1 2.5 1 2.5 mA
Voltage Gain RL15 kΩ, V+=15V 50 200 50 200 25 100 V/mV
VO= 1V to 11V
Large Signal Response VIN=TTL Logic Swing, VREF=1.4V 300 300 300 ns
Time VRL=5V, RL=5.1 kΩ
Response Time VRL=5V, RL=5.1 kΩ(4) 1.3 1.3 1.5 μs
Output Sink Current VIN()=1V, VIN(+)=0, VO1.5V 6.0 16 6.0 16 6.0 16 mA
Saturation Voltage VIN()=1V, VIN(+)=0, ISINK4 mA 250 400 250 400 250 400 mV
Output Leakage Current VIN()=0, VIN(+)=1V, VO=5V 0.1 0.1 0.1 nA
(1) At output switch point, VO1.4V, RS=0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+1.5V), at 25°C.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+1.5V at 25°C, but either or both inputs can go to 36V without damage, independent of the
magnitude of V+.
(4) The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
Typical Performance Characteristics.
4Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
Electrical Characteristics
(V+ = 5V) (1)
LM193A
Parameter Test Conditions Units
Min Typ Max
Input Offset Voltage (2) 4.0 mV
Input Offset Current IIN(+)IIN(), VCM=0V 100 nA
Input Bias Current IIN(+) or IIN() with Output in Linear Range, 300 nA
VCM=0V (3)
Input Common Mode Voltage Range V+=30V (4) 0 V+2.0 V
Saturation Voltage VIN()=1V, VIN(+)=0, ISINK4 mA 700 mV
Output Leakage Current VIN()=0, VIN(+)=1V, VO=30V 1.0 μA
Differential Input Voltage Keep All VIN's0V (or V, if Used), (5) 36 V
(1) These specifications are limited to 55°CTA+125°C, for the LM193/LM193A. With the LM293 all temperature specifications are limited
to 25°CTA+85°C and the LM393 temperature specifications are limited to 0°CTA+70°C. The LM2903 is limited to
40°CTA+85°C.
(2) At output switch point, VO1.4V, RS=0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+1.5V), at 25°C.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+1.5V at 25°C, but either or both inputs can go to 36V without damage, independent of the
magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than 0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
Electrical Characteristics
(V+ = 5V) (1)
LM193 LM293, LM393 LM2903
Parameter Test Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage (2) 9 9 9 15 mV
Input Offset Current IIN(+)IIN(), VCM=0V 100 150 50 200 nA
Input Bias Current IIN(+) or IIN() with Output in Linear 300 400 200 500 nA
Range, VCM=0V
(3)
Input Common Mode V+=30V (4) 0 V+2.0 0 V+2.0 0 V+2.0 V
Voltage Range
Saturation Voltage VIN()=1V, VIN(+)=0, 700 700 400 700 mV
ISINK4 mA
Output Leakage Current VIN()=0, VIN(+)=1V, VO=30V 1.0 1.0 1.0 μA
Differential Input Voltage Keep All VIN's0V (or V, if Used), 36 36 36 V
(5)
(1) These specifications are limited to 55°CTA+125°C, for the LM193/LM193A. With the LM293 all temperature specifications are limited
to 25°CTA+85°C and the LM393 temperature specifications are limited to 0°CTA+70°C. The LM2903 is limited to
40°CTA+85°C.
(2) At output switch point, VO1.4V, RS=0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+1.5V), at 25°C.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+1.5V at 25°C, but either or both inputs can go to 36V without damage, independent of the
magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than 0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
LM193/LM293/LM393, LM193A
Supply Current Input Current
Figure 7. Figure 8.
Response Time for Various Input Overdrives—Negative
Output Saturation Voltage Transition
Figure 9. Figure 10.
Response Time for Various Input Overdrives—Positive Transition
Figure 11.
6Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
Typical Performance Characteristics
LM2903
Supply Current Input Current
Figure 12. Figure 13.
Response Time for Various Input Overdrives—Negative
Output Saturation Voltage Transition
Figure 14. Figure 15.
Response Time for Various Input Overdrives—Positive Transition
Figure 16.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
APPLICATION HINTS
The LM193 series are high gain, wide bandwidth devices which, like most comparators, can easily oscillate if the
output lead is inadvertently allowed to capacitively couple to the inputs via stray capacitance. This shows up only
during the output voltage transition intervals as the comparator change states. Power supply bypassing is not
required to solve this problem. Standard PC board layout is helpful as it reduces stray input-output coupling.
Reducing the input resistors to < 10 kΩreduces the feedback signal levels and finally, adding even a small
amount (1.0 to 10 mV) of positive feedback (hysteresis) causes such a rapid transition that oscillations due to
stray feedback are not possible. Simply socketing the IC and attaching resistors to the pins will cause input-
output oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse
waveform, with relatively fast rise and fall times, hysteresis is not required.
All input pins of any unused comparators should be tied to the negative supply.
The bias network of the LM193 series establishes a drain current which is independent of the magnitude of the
power supply voltage over the range of from 2.0 VDC to 30 VDC.
It is usually unnecessary to use a bypass capacitor across the power supply line.
The differential input voltage may be larger than V+without damaging the device(1). Protection should be
provided to prevent the input voltages from going negative more than 0.3 VDC (at 25°C). An input clamp diode
can be used as shown in Typical Applications.
The output of the LM193 series is the uncommitted collector of a grounded-emitter NPN output transistor. Many
collectors can be tied together to provide an output OR'ing function. An output pull-up resistor can be connected
to any available power supply voltage within the permitted supply voltage range and there is no restriction on this
voltage due to the magnitude of the voltage which is applied to the V+terminal of the LM193 package. The
output can also be used as a simple SPST switch to ground (when a pull-up resistor is not used). The amount of
current which the output device can sink is limited by the drive available (which is independent of V+) and the β
of this device. When the maximum current limit is reached (approximately 16mA), the output transistor will come
out of saturation and the output voltage will rise very rapidly. The output saturation voltage is limited by the
approximately 60ΩrSAT of the output transistor. The low offset voltage of the output transistor (1.0mV) allows the
output to clamp essentially to ground level for small load currents.
Typical Applications
(V+=5.0 VDC)
Figure 17. Basic Comparator Figure 18. Driving CMOS
(1) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than 0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
8Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
(V+=5.0 VDC)
Figure 19. Driving TTL Figure 20. Squarewave Oscillator
* For large ratios of R1/R2,
D1 can be omitted.
Figure 21. Pulse Generator Figure 22. Crystal Controlled Oscillator
V* = +30 VDC
+250 mVDC VC+50 VDC
700Hz fo100kHz
Figure 23. Two-Decade High Frequency VCO
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
(V+=5.0 VDC)
Figure 24. Basic Comparator Figure 25. Non-Inverting Comparator with
Hysteresis
Figure 26. Inverting Comparator with Hysteresis Figure 27. Output Strobing
Figure 28. AND Gate Figure 29. OR Gate
10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
(V+=5.0 VDC)
Figure 30. Large Fan-in AND Gate Figure 31. Limit Comparator
Figure 32. Comparing Input Voltages of Opposite Figure 33. ORing the Outputs
Polarity
Figure 34. Zero Crossing Detector (Single Power Figure 35. One-Shot Multivibrator
Supply)
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
(V+=5.0 VDC)
Figure 36. Bi-Stable Multivibrator Figure 37. One-Shot Multivibrator with Input Lock
Out
Figure 38. Zero Crossing Detector Figure 39. Comparator With a Negative Reference
Figure 40. Time Delay Generator
12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
www.ti.com
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
(V+=5.0 VDC)
Split-Supply Applications
(V+=+15 VDC and V=15 VDC)
Figure 41. MOS Clock Driver
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N, LM2903-N, LM293-N, LM393-N
SNOSBJ6E OCTOBER 1999REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 13
14 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM193AH ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 LM193AH
LM193AH/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM193AH
LM193H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 LM193H
LM193H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM193H
LM2903ITL/NOPB ACTIVE DSBGA YZR 8 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 C
03
LM2903ITLX/NOPB ACTIVE DSBGA YZR 8 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 C
03
LM2903M NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM
2903M
LM2903M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM
2903M
LM2903MX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LM
2903M
LM2903MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM
2903M
LM2903N NRND PDIP P 8 40 TBD Call TI Call TI -40 to 85 LM
2903N
LM2903N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM
2903N
LM293H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -25 to 85 LM293H
LM293H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -25 to 85 LM293H
LM393M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM
393M
LM393M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM
393M
LM393MX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM
393M
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM393MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM
393M
LM393N NRND PDIP P 8 40 TBD Call TI Call TI 0 to 70 LM
393N
LM393N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN | Call TI Level-1-NA-UNLIM 0 to 70 LM
393N
LM393TL/NOPB ACTIVE DSBGA YZR 8 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 C
02
LM393TLX/NOPB ACTIVE DSBGA YZR 8 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 C
02
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 3
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2903ITL/NOPB DSBGA YZR 8 250 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM2903ITLX/NOPB DSBGA YZR 8 3000 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM2903MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM2903MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393TL/NOPB DSBGA YZR 8 250 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM393TLX/NOPB DSBGA YZR 8 3000 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 26-Mar-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2903ITL/NOPB DSBGA YZR 8 250 210.0 185.0 35.0
LM2903ITLX/NOPB DSBGA YZR 8 3000 210.0 185.0 35.0
LM2903MX SOIC D 8 2500 367.0 367.0 35.0
LM2903MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LM393MX SOIC D 8 2500 367.0 367.0 35.0
LM393MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LM393TL/NOPB DSBGA YZR 8 250 210.0 185.0 35.0
LM393TLX/NOPB DSBGA YZR 8 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 26-Mar-2013
Pack Materials-Page 2
MECHANICAL DATA
YZR0008xxx
www.ti.com
TLA08XXX (Rev C)
0.600±0.075 D
E
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
4215045/A 12/12
D: Max =
E: Max =
1.54 mm, Min =
1.54 mm, Min =
1.479 mm
1.479 mm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated