http://www.tracopower.com
Features
◆ Highest power density: 60W in a
51x51x10mm (2”x2”x0.4”) package
◆ Wide 2:1 input voltage range
◆ Very high efficiency up to 90%
◆ No minimum load required
◆ Over temperature protection
◆ Under voltage lock-out circuit
◆ Remote On/Off
◆ Shielded metal case with insulated
baseplate
◆ Optional heatsink
◆ Lead free design - RoHS compliant
◆ 3-year product warranty
DC/DC Converters
TEN 60 Series, 60 Watt
The TEN 60 series is a family of high performance 60W dc-dc converter modules with
wide 2:1 input voltage ranges in a compact low profile case with industry-standard
footprint. A very high efficiency allows an operating temperature range of –40°C to
85°C. Built-in filters for both input and output minimizes the need for external filtering.
Further standard features include remote On/Off, output voltage trimming, over volt-
age protection, under voltage lockout and short circuit protection.
Typical applications for these products are battery operated equipment and distributed
power architectures in communication and industrial electronics, everywhere where
isolated, tightly regulated voltages are required and space is limited on the PCB.
Page 1 of 4
Order code Input voltage range Output voltage Output current max. Efficiency typ.
TEN 60-2410 3.3 VDC 14.0 A 89 %
TEN 60-2411 18 – 36 VDC 5.0 VDC 12.0 A 90 %
TEN 60-2412 (24 VDC nominal) 12 VDC 5.0 A 90 %
TEN 60-2413 15 VDC 4.0 A 90 %
TEN 60-2415 24 VDC 2.5 A 89 %
TEN 60-4810 3.3 VDC 14.0 A 89 %
TEN 60-4811 36 – 75 VDC 5.0 VDC 12.0 A 90 %
TEN 60-4812 (48 VDC nominal) 12 VDC 5.0 A 90 %
TEN 60-4813 15 VDC 4.0 A 90 %
TEN 60-4815 24 VDC 2.5 A 89 %
Models
UL 60950-1
http://www.tracopower.com
Input Specifications
Input current at no load 3.3 V output models: 100 / 80 mA typ.
(nominal input 24/48 Vin) 5.0 V output models: 130 / 90 mA typ.
12 V, 15 V & 24 V output models: 50 / 30 mA typ.
Input current at full load 3.3 V output models: 2260 / 1140 mA typ.
(nominal input 24/48 Vin) 5.0 V output models: 2940 / 1450 mA typ.
12 V & 15 V output models: 2900 / 1450 mA typ.
24 V output models: 2940 / 1470 mA typ.
Input voltage variation (dv/dt) 5 V/ms, max.
(complies with ETS300 132 part 4.4)
Start-up voltage 24 Vin models: 17 VDC (or lower)
48 Vin models: 34 VDC (or lower)
Under voltage shut down (lock-out circuit) 24 Vin models: 15 VDC typ.
48 Vin models: 32 VDC typ.
Surge voltage (100 msec. max.) 24 Vin models: 50 V
48 Vin models: 100 V
Conducted noise (input) EN 55022 level A, FCC part 15, level A with
external capacitor, see application note:
www.tracopower.com/overview/ten60
ESD (input) EN 61000-4-2, perf. criteria A
Fast transient (input) EN 61000-4-4, perf. criteria A
Surge (input) EN 61000-4-5, perf. criteria A
Output Specifications
Voltage set accuracy ±1 %
Output voltage adjustment ±10 %
Regulation – Input variation Vin min. to Vin max. 0.2 % max.
– Load variation 0 – 100 % 0.5 % max.
Temperature coefficient ±0.02 %/K max.
Ripple and noise (20 MHz Bandwidth) 3.3 V & 5 V output models: 75 mVpk-pk max.
12 V & 15 V output models: 100 mVpk-pk max.
24 V output models: 200 mVpk-pk max.
Start up time (nominal Vin and constant resistive load) 20 ms typ.
Transient response time (25% load change) 250 µs typ.
Short circuit protection indefinite (automatic recovery)
Over load protection 150 % of Iout max typ.
Minimum Load not required
Thermal shutdown at +110°C typ
Over voltage protection 3.3 V output models: 3.7 V
5 V output models: 5.6 V
12 V output models: 13.8 V
15 V output models: 16.8 V
24 V output models: 30.0 V
Capacitive load 3.3 V output models: 36’000 µF
5 V output models: 20 ’40 0 µ F
12 V output models: 3’550 µF
15 V output models: 2’300 µF
24 V output models: 885 µFGeneral Specifications
DC/DC Converters
TEN 60 60 Watt
Page 2 of 4
http://www.tracopower.com
DC/DC Converters
TEN 60 60 Watt
General Specifications
Temperature ranges – Operating –40°C to +85°C
– Case temperature +110°C m a x.
– Storage –55°C to +125°C
Derating see application note:
www.tracopower.com/overview/ten60
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +70°C, ground benign) >400’000 h
Isolation (Input/Output) – Voltage 1‘600 VDC
– Capacitance 1’500 pF max.
– Resistance >1‘000 MOhm
Remote On/Off – On: 3.0 ... 12 VDC or open circuit.
– Off: 0 ... 1.2 VDC or short circuit pin 3 and pin 2
– Off idle current: 3.0 mA max.
Switching frequency (fixed) 300 kHz typ. (Pulse width modulation PWM)
Vibration 10 – 55Hz, 10G, 30 minutes along X,Y,Z
Safety standards UL 60950-1, IEC/EN 60950-1
Safety approvals – Certification documents www.tracopower.com/overview/ten60
Environmental compliance – Reach www.tracopower.com/products/reach-declaration.pdf
– RoHS RoHS directive 2011/65/EU
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Page 3 of 4
Physical Specifications
Casing material copper, nickel plated
Baseplate material none conductive FR4
Potting material epoxy (UL 94V-0-rated)
Weight 60 g (2.1oz)
Soldering temperature max. 265°C / 10 sec.
Outline Dimensions
Pin
1
+Vin (Vcc)
2
–Vin (GND)
3
Remote On/Off
4
–Sense
5
+Sense
6
+Vout
7
–Vout
8
Trim
Pin-Out
Dimensions in [mm], () = Inch
Pin diameter: 1.0 ±0.05 (0.02 ±0.002)
Pin pitch tolerances: ±0.35 (± 0.014 )
Case tolerances: ±0.5 (±0.02)
5.6
10.2
50.8
5.08
12.7
50.8
7
6
51
2
3
8
Bottom
view
45.7
(2.0)
(0.22)
(2.0)
(0.2)
(0.4)
(0.3)
(0.5)
(1.8)
5.08
(0.2)
7.62
(0.3)
4
10.16
(0.4)
7.62 7.625.08
(0.2)(0.3)
Supporting documents: www.tracopower.com/overview/ten60
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
Outline Dimensions
Rev. July 11, 2018
Heat-sink TEN-HS3
Note:
The product label on converter has to be removed before
mounting the heat-sink.
For volume orders converters will be supplied with heat-
sinks already mounted. Please contact factory for quota-
tion.
Separate heat-sinks are only available for prototypes and
small quantity orders.
Page 4 of 4
DC/DC Converters
TEN 60 60 Watt
56.0 (2.2) max.
25.2 (0.1)
17.0 (0.67)
max.
Converter
Heat-sink
Thermal pad
Clamp
Order code: TEN-HS3 (cont.: heat-sink, thermal pad, 2 clamps)
Material: Aluminum
Finish: Anodic treatment (black)
Weight: 22 g (0.78oz) (without converter)
