Product Folder Sample & Buy Support & Community Tools & Software Technical Documents Reference Design LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 LP2985-N Micropower 150-mA Low-Noise Ultra-Low-Dropout Regulator in a SOT-23 Package Designed for Use With Very Low ESR Output Capacitors 1 Features 3 Description * * * * * * * * * * * * * The LP2985-N low noise linear (LDO) regulator delivers up to 150-mA output current and only requires 300-mV dropout voltage of input to output. Using an optimized vertically integrated PNP (VIP) process, the LP2985-N delivers unequaled performance for all battery-powered designs. The LP2985-N device provides 1% tolerance precision output voltage with only 75-A quiescent current at 1mA load and 850 A at 150-mA load. By adding a 10nF bypass capacitor, the output noise can be reduced to 30 VRMS in a 30-kHz bandwidth. 1 Input Voltage Range: 2.5 V to 16 V Ultra Low-Dropout Voltage Ensured 150 mA Output Current Requires Minimum External Components Stable With Low-ESR Output Capacitor < 1 A Quiescent Current When Shut Down Low Ground Pin Current at All Loads Output Voltage Accuracy 1% (A Grade) High Peak Current Capability Low ZOUT: 0.3 Typical (10 Hz to 1 MHz) Overtemperature and Overcurrent Protection -40C to 125C Junction Temperature Range Custom Voltages Available The LP2985-N is designed to work with a ceramic output capacitor with equivalent series resistance (ESR) as low as 5 m. The device is available with fixed output voltage from 2.5 V to 6.1 V. Contact Texas Instrument Sales for specific voltage option needs. 2 Applications * * * * Device Information(1) Cellular Phones Palmtop and Laptop Computers Personal Digital Assistants (PDA) Camcorders, Personal Stereos, Cameras PART NUMBER LP2985-N PACKAGE SOT-23 (5) BODY SIZE (NOM) 2.90 mm x 1.60 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Simplified Schematic VIN IN CIN 1 F VOUT OUT LP2985 COUT 2.2 F GND ON/OFF ON/OFF BYPASS CBYPASS 0.01 F 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 5 5 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 11 7.1 Overview ................................................................. 11 7.2 Functional Block Diagram ....................................... 11 7.3 Feature Description................................................. 11 7.4 Device Functional Modes........................................ 13 8 Application and Implementation ........................ 14 8.1 Application Information............................................ 14 8.2 Typical Application .................................................. 14 9 Power Supply Recommendations...................... 21 10 Layout................................................................... 21 10.1 Layout Guidelines ................................................. 21 10.2 Layout Example .................................................... 21 11 Device and Documentation Support ................. 22 11.1 11.2 11.3 11.4 11.5 11.6 Documentation Support ........................................ Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 22 22 22 22 22 22 12 Mechanical, Packaging, and Orderable Information ........................................................... 22 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision X (May 2015) to Revision Y Page * Added top nav icon for TI Designs ........................................................................................................................................ 1 * Deleted "Smallest Possible Size (SOT-23 Package)" from Features..................................................................................... 1 * Deleted all information re: DSBGA package - it is no longer available ................................................................................. 1 * Deleted DSBGA pin function info from Pin Functions ............................................................................................................ 3 * Deleted infor re: DSBGA package; changed "...value of RJA for the SOT-23 package is 175.7C/W ..." to "...value of RJA for the SOT-23 package is 169.0C/W..." in footnote 3 to Abs Max table - see update thermal info for SOT-23 in Thermal Information............................................................................................................................................................ 4 * Changed "All pins except 3 and 4 (SOT-23)" to "Pins 3 and 4 ." .......................................................................................... 4 * Changed thermal values for SOT-23 package; added Note 2 to Thermal Information table ................................................ 5 * Deleted footnote 1 to Electrical Characteristics ..................................................................................................................... 5 * Changed content in last 2 paragraphs of Reverse Input-Output Voltage ........................................................................... 17 * Added Power Dissipation and Estimating Junction Temperature subsections ................................................................... 18 Changes from Revision W (September 2014) to Revision X Page * Changed pin names in text and app circuit drawing "VOUT" and "VIN" to "OUT" and "IN"; replace Handling Ratings with ESD Ratings; update Thermal Values ........................................................................................................................... 1 * Changed footnote 1 to Ab Max table per new format ........................................................................................................... 4 * Changed location of storage temperature range from Handling Ratings to Ab Max table..................................................... 4 * Added required Application Information section .................................................................................................................. 14 Changes from Revision V (April 2013) to Revision W * 2 Page Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information .................. 1 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Changes from Revision U (April 2013) to Revision V * Page Changed layout of National Semiconductor data sheet ...................................................................................................... 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 3 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 5 Pin Configuration and Functions DBV Package 5 Pin SOT-23 Top View Pin Functions PIN NAME NO. TYPE DESCRIPTION BYPASS 4 I/O Bypass capacitor for low noise operation GND 2 -- Common ground (device substrate) IN 1 I Input voltage ON/OFF 3 I Logic high enable input OUT 5 O Regulated output voltage 4 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) Operating junction temperature Power dissipation (3) MIN MAX UNIT -40 125 C Internally Limited Input supply voltage (survival) -0.3 16 V Input supply voltage (operating) 2.5 16 V Shutdown input voltage (survival) -0.3 16 V Output voltage (survival) (4) -0.3 9 V IOUT (survival) Short Circuit Protected Input-output voltage (survival) (5) -0.3 16 V Storage temperature, Tstg -65 150 C (1) (2) (3) (4) (5) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ_MAX, the junction-to-ambient thermal resistance, RJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: TJ _ MAX TA PMAX RT JA Where the value of RJA for the SOT-23 package is 169.0C/W in a typical PC board mounting. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. For 12-V option, output voltage survival: -0.3 to +16 V. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2985-N output must be diode-clamped to ground. The output PNP structure contains a diode between the IN to OUT pins that is normally reverse-biased. Reversing the polarity from IN to OUT will turn on this diode. 6.2 ESD Ratings VALUE V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) Pins 3 and 4 1000 Pins 1, 2, and 5 2000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN VIN Supply input voltage 3.1 VON/OFF ON/OFF input voltage IOUT Output current TJ Operating junction temperature (1) MAX UNIT (1) 16 0 VIN V 150 mA 125 C -40 V Recommended minimum VIN is the greater of 3.1 V or VOUT(MAX) + rated dropout voltage (maximum) for operating load current. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 5 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 6.4 Thermal Information LP2985-N THERMAL METRIC (1) DBV (SOT-23) UNIT 5 PINS RJA Junction-to-ambient thermal resistance, High K (2) 169.0 C/W RJC(top) Junction-to-case (top) thermal resistance 121.8 C/W RJB Junction-to-board thermal resistance 29.5 C/W JT Junction-to-top characterization parameter 16.1 C/W JB Junction-to-board characterization parameter 29.0 C/W (1) (2) For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics application report, SPRA953. Thermal resistance value RJA is based on the EIA/JEDEC High-K printed circuit board defined by JESD51-7 High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages. 6.5 Electrical Characteristics Unless otherwise specified: VIN = VO(NOM) + 1 V, IL = 1 mA, CIN = 1 F, COUT = 4.7 F, VON/OFF = 2 V, TJ = 25C. PARAMETER TEST CONDITIONS TYP -1.5 1.5 -2.5 2.5 -2.5 2.5 -3.5 3.5 1 mA IL 150 mA -2.5 2.5 -3 3 1 mA IL 150 mA, -40C TJ 125C -3.5 3.5 -4 4 Output voltage VO(NOM)+1 V VIN 16 V Line regulation VO(NOM)+1 V VIN 16 V, -40C TJ 125C %VNOM 0.007 1 IL = 0 mA, -40C TJ 125C IL = 1 mA 7 IL = 1 mA, -40C TJ 125C IL = 10 mA 40 IL = 10 mA, -40C TJ 125C IL = 50 mA 120 IL = 50 mA, -40C TJ 125C IL = 150 mA 280 IL = 150 mA, -40C TJ 125C (1) (2) 6 UNIT MAX 1 1 mA IL 50 mA, -40C TJ Output voltage tolerance 125C Dropout voltage (2) MIN 1.5 IL = 0 mA VIN-VO MAX -1 1 mA IL 50 mA VO/VIN MIN LP2985I-X.X (1) -1.5 IL = 1 mA VO LP2985AI-X.X (1) 0.014 0.014 0.032 0.032 3 3 5 5 10 10 15 15 60 60 90 90 150 150 225 225 350 350 575 575 %/V mV Limits are 100% production tested at 25C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate TI's Average Outgoing Quality Level (AOQL). Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1-V differential. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Electrical Characteristics (continued) Unless otherwise specified: VIN = VO(NOM) + 1 V, IL = 1 mA, CIN = 1 F, COUT = 4.7 F, VON/OFF = 2 V, TJ = 25C. PARAMETER TEST CONDITIONS IL = 0 mA TYP LP2985AI-X.X (1) MIN 65 IL = 0 mA, -40C TJ 125C IL = 1 mA 75 IL = 1 mA, -40C TJ 125C IL = 10 mA 120 IL = 10 mA, -40C TJ 125C IGND IL = 50 mA Ground pin current 350 IL = 50 mA, -40C TJ 125C IL = 150 mA 850 IL = 150 mA, -40C TJ 125C VON/OFF ON/OFF input voltage (3) MIN UNIT MAX 95 95 125 125 110 110 170 170 220 220 400 400 600 600 1000 1000 1500 1500 2500 2500 0.01 0.8 0.8 VON/OFF < 0.15 V, -40C TJ 125C 0.05 2 2 High = O/P ON 1.4 High = O/P ON, -40C TJ 125C Low = O/P OFF VON/OFF = 0 V ON/OFF input current MAX VON/OFF < 0.3 V 1.6 V 0.15 0.15 -2 -2 0.01 VON/OFF = 0 V, -40C TJ 125C VON/OFF = 5 V A 1.6 0.55 Low = O/P OFF, -40C TJ 125C ION/OFF LP2985I-X.X (1) A 5 VON/OFF = 5 V, -40C TJ 125C 15 15 BW = 300 Hz to 50 kHz, Output noise voltage (RMS) en COUT = 10 F 30 V 45 dB CBYPASS = 10 nF f = 1 kHz, CBYPASS = 10 nF VO/VIN Ripple rejection IO(SC) Short circuit current RL = 0 (steady state) (4) 400 mA IO(PK) Peak output current VOUT VO(NOM) -5% 350 mA (3) (4) COUT = 10 F The ON/OFF input must be properly driven to prevent possible misoperation. For details, refer to ON/OFF Input Operation. The LP2985-N has foldback current limiting which allows a high peak current when VOUT > 0.5 V, and then reduces the maximum output current as VOUT is forced to ground (see Typical Characteristics curves). Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 7 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 6.6 Typical Characteristics Unless otherwise specified: CIN = 1 F, COUT = 4.7 F, VIN = VOUT(NOM) + 1, TA = 25C, ON/OFF pin is tied to VIN. 8 Figure 1. VOUT vs Temperature Figure 2. Short Circuit Current vs Output Voltage Figure 3. Ripple Rejection Figure 4. Ripple Rejection Figure 5. Ripple Rejection Figure 6. Ripple Rejection Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Typical Characteristics (continued) Unless otherwise specified: CIN = 1 F, COUT = 4.7 F, VIN = VOUT(NOM) + 1, TA = 25C, ON/OFF pin is tied to VIN. Figure 7. Ripple Rejection Figure 8. Ripple Rejection Figure 9. Ripple Rejection Figure 10. Ripple Rejection Figure 11. Ripple Rejection Figure 12. Output Impedance vs Frequency Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 9 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com Typical Characteristics (continued) Unless otherwise specified: CIN = 1 F, COUT = 4.7 F, VIN = VOUT(NOM) + 1, TA = 25C, ON/OFF pin is tied to VIN. 10 Figure 13. Output Impedance vs Frequency Figure 14. Output Noise Density Figure 15. Output Noise Density Figure 16. Ground Pin vs Load Current Figure 17. Dropout Voltage vs Temperature Figure 18. Input Current vs Pin Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Typical Characteristics (continued) Unless otherwise specified: CIN = 1 F, COUT = 4.7 F, VIN = VOUT(NOM) + 1, TA = 25C, ON/OFF pin is tied to VIN. Figure 19. GND Pin Current vs Temperature Figure 20. Instantaneous Short Circuit Current Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 11 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 7 Detailed Description 7.1 Overview The LP2985-N family of fixed-output, ultra-low-dropout and low-noise regulators offers exceptional, cost-effective performance for battery-powered applications. Available in output voltages from 2.5 V to 5 V, the family has an output tolerance of 1% for the A version (1.5% for the non-A version) and is capable of delivering 150-mA continuous load current. Standard regulator features, such as overcurrent and overtemperature protection, are also included. Using an optimized vertically integrated PNP (VIP) process, the LP2985-N contains several features to facilitate battery powered designs: * Multiple voltage options * Low dropout voltage, typical dropout of 300 mV at 150-mA load current and 7 mV at 1-mA load. * Low quiescent current and low ground current, typically 850-A at 150 mA load, and 75-A at 1-mA load. * A shutdown feature is available, allowing the regulator to consume only 0.01-A typically when the ON/OFF pin is pulled low. * Overtemperature protection and overcurrent protection circuitry is designed to safeguard the device during unexpected conditions * Enhanced stability: The LP2985-N is stable with output capacitor ESR as low as 5 m, which allows the use of ceramic capacitors on the output. * Low noise: A BYPASS pin allows for low-noise operation, with a typical output noise of 30 VRMS, with the use of a 10-nF bypass capacitor. 7.2 Functional Block Diagram 7.3 Feature Description 7.3.1 Multiple Voltage Options In order to meet different application's requirement, the LP2985-N family provide multiple fixed output options from 2.5 V to 6.1 V. Consult factory for custom voltages. 7.3.2 Output Voltage Accuracy Output voltage accuracy specifies minimum and maximum output voltage error, relative to the expected nominal output voltage stated as a percent. This accuracy error includes the errors introduced by the internal reference and the load and line regulation across the full range of rated load and line operating conditions over temperature, unless otherwise specified by the Electrical Characteristics. Output voltage accuracy also accounts for all variations between manufacturing lots. 12 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Feature Description (continued) 7.3.3 Ultra-Low-Dropout Voltage Generally speaking, the dropout voltage often refers to the voltage difference between the input and output voltage (VDO = VIN - VOUT), where the main current pass-FET is fully on in the ohmic region of operation and is characterized by the classic RDS(ON) of the FET. VDO indirectly specifies a minimum input voltage above the nominal programmed output voltage at which the output voltage is expected to remain within its accuracy boundary. If the input falls below this VDO limit (VIN < VOUT + VDO), then the output voltage decreases in order to follow the input voltage. 7.3.4 Low Ground Current LP2985-N uses a vertical PNP process which allows for quiescent currents that are considerably lower than those associated with traditional lateral PNP regulators, typically 850 A at 150-mA load and 75 A at 1-mA load. 7.3.5 Sleep Mode When pull ON/OFF pin to low level, LP2985-N enters sleep mode, and less than 2-A quiescent current is consumed. This function is designed for the application which needs a sleep mode to effectively enhance battery life cycle. 7.3.6 Internal Protection Circuitry 7.3.6.1 Short Circuit Protection (Current Limit) The internal current limit circuit is used to protect the LDO against high-load current faults or shorting events. The LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources constant current. Therefore, the output voltage falls when load impedance decreases. Note also that if a current limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO, resulting in a thermal shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from damage under all load conditions. If VOUT is forced below 0 V before EN goes high and the load current required exceeds the foldback current limit, the device may not start up correctly. 7.3.6.2 Thermal Protection The LP2985-N contains a thermal shutdown protection circuit to turn off the output current when excessive heat is dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The internal protection circuitry of the LP2985-N is designed to protect against thermal overload conditions. The circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown degrades its reliability. 7.3.7 Enhanced Stability The LP2985-N is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to be stable across the entire range of output current with an output capacitor whose ESR is as low as 5 m. For output capacitor requirement, please refer to Output Capacitor. 7.3.8 Low Noise The LP2985-N includes a low-noise reference ensuring minimal noise during operation because the internal reference is normally the dominant term in noise analysis. Further noise reduction can be achieved by adding an external bypass bapacitor between the BYPASS pin and the GND pin. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 13 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 7.4 Device Functional Modes 7.4.1 Operation with VOUT(TARGET) + 0.6 V VIN > 16 V The device operate if the input voltage is equal to, or exceeds VOUT(TARGET) + 0.6 V. At input voltages below the minimum VIN requirement, the devices do not operate correctly and output voltage may not reach target value. 7.4.2 Operation With ON/OFF Control If the voltage on the ON/OFF pin is less than 0.15 V, the device is disabled, and in this state shutdown current does not exceed 2 A. Raising ON/OFF above 1.6 V initiates the start-up sequence of the device. 14 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LP2985-N is a linear voltage regulator operating from 2.5 V to 16 V on the input and regulates voltages between 2.5 V to 6.1 V with 1% accuracy and 150-mA maximum output current. Efficiency is defined by the ratio of output voltage to input voltage because the LP2985-N is a linear voltage regulator. To achieve high efficiency, the dropout voltage (VIN - VOUT) must be as small as possible, thus requiring a very-low-dropout LDO. Successfully implementing an LDO in an application depends on the application requirements. If the requirements are simply input voltage and output voltage, compliance specifications (such as internal power dissipation or stability) must be verified to ensure a solid design. If timing, start-up, noise, power supply rejection ratio (PSRR), or any other transient specification is required, then the design becomes more challenging. 8.2 Typical Application *ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used. **Minimum capacitance is shown to ensure stability (may be increased without limit). Ceramic capacitor required for output (see Output Capacitor). ***Reduces output noise (may be omitted if application is not noise critical). Use ceramic or film type with very low leakage current (see Noise Bypass Capacitor). Figure 21. Typical Application Schematic 8.2.1 Design Requirements For typical design parameters, see Table 1. Table 1. Design Parameters DESIGN PARAMETERS VALUE Input voltage 4.3 V, 10% provided by the DC-DC converter switching at 1 MHz Output voltage 3.3 V, 5% Output current 150 mA (maximum), 1 mA (minimum) RMS noise, 300 Hz to 50 kHz < 50 VRMS PSRR at 1 kHz > 40 dB Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 15 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 8.2.2 Detailed Design Procedure At 150-mA loading, the dropout of the LP2985-N has 575-mV maximum dropout over temperature, thus an 1000mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the LP2985-N in this configuration is VOUT / VIN = 76.7%. To achieve the smallest form factor, the SOT-23 package is selected. Input and output capacitors are selected in accordance with the Capacitor Characteristics section. Ceramic capacitances of 1 F for the input and one 2.2-F capacitor for the output are selected. With an efficiency of 76.7% and a 150-mA maximum load, the internal power dissipation is 150 mW, which corresponds to a 26C junction temperature rise for the SOT-23 package. With an 85C maximum ambient temperature, the junction temperature is at 111C. To minimize noise, a bypass capacitance (CBYPASS) of 0.01 F is selected. 8.2.2.1 External Capacitors Like any low-dropout regulator, the LP2985-N requires external capacitors for regulator stability. These capacitors must be correctly selected for good performance. 8.2.2.1.1 Input Capacitor An input capacitor whose capacitance is 1 F is required between the LP2985-N input and ground (the amount of capacitance may be increased without limit). This capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. NOTE Tantalum capacitors can suffer catastrophic failure due to surge current when connected to a low-impedance source of power (like a battery or very large capacitor). If a Tantalum capacitor is used at the input, it must be ensured by the manufacturer to have a surge current rating sufficient for the application. There are no requirements for ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be 1 F over the entire operating temperature range. 8.2.2.1.2 Output Capacitor The LP2985-N is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to be stable across the entire range of output current with an output capacitor whose ESR is as low as 5 m. It may also be possible to use tantalum or film capacitors at the output, but these are not as attractive for reasons of size and cost (see Capacitor Characteristics). The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR value which is within the stable range. Curves are provided which show the stable ESR range as a function of load current (see Figure 22). Figure 22. ESR Graph 16 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 NOTE The output capacitor must maintain its ESR within the stable region over the full operating temperature range of the application to assure stability. The LP2985-N requires a minimum of 2.2 F on the output (output capacitor size can be increased without limit). It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full operating temperature range. Ceramic capacitors can exhibit large changes in capacitance with temperature (see Capacitor Characteristics). The output capacitor must be located not more than 1 cm from the output pin and returned to a clean analog ground. 8.2.2.1.3 Noise Bypass Capacitor Connecting a 10-nF capacitor to the BYPASS pin significantly reduces noise on the regulator output. The capacitor is connected directly to a high-impedance circuit in the bandgap reference. Because this circuit has only a few microamperes flowing in it, any significant loading on this node will cause a change in the regulated output voltage. For this reason, DC leakage current through the noise bypass capacitor must never exceed 100 nA and must be kept as low as possible for best output voltage accuracy. The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic capacitors with either NPO or COG dielectric typically have very low leakage. 10-nF polypropolene and polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low leakage current. 8.2.2.2 Capacitor Characteristics The LP2985-N was designed to work with ceramic capacitors on the output to take advantage of the benefits they offer: for capacitance values in the 2.2-F to 4.7-F range, ceramics are the least expensive and also have the lowest ESR values (which makes them best for eliminating high-frequency noise). The ESR of a typical 2.2F ceramic capacitor is in the range of 10 m to 20 m, which easily meets the ESR limits required for stability by the LP2985-N. One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Most large value ceramic capacitors ( 2.2 F) are manufactured with the Z5U or Y5V temperature characteristic, which results in the capacitance dropping by more than 50% as the temperature goes from 25C to 85C. This could cause problems if a 2.2-F capacitor were used on the output because it will drop down to approximately 1 F at high ambient temperatures (which could cause the LM2985 to oscillate). If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 4.7 F must be observed. A better choice for temperature coefficient in ceramic capacitors is X7R, which holds the capacitance within 15%. Unfortunately, the larger values of capacitance are not offered by all manufacturers in the X7R dielectric. Tantalum capacitors are less desirable than ceramics for use as output capacitors because they are more expensive when comparing equivalent capacitance and voltage ratings in the 1 F to 4.7 F range. Another important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a Tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. Note that the ESR of a typical tantalum will increase about 2:1 as the temperature goes from 25C down to -40C, so some guard band must be allowed. 8.2.2.3 ON/OFF Input Operation The LP2985-N is shut off by driving the ON/OFF input low, and turned on by pulling it high. If this feature is not to be used, the ON/OFF input must be tied to VIN to keep the regulator output on at all times. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 17 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com To assure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on/turn-off voltage thresholds listed in the Electrical Characteristics section under VON/OFF. To prevent mis-operation, the turn-on (and turn-off) voltage signals applied to the ON/OFF input must have a slew rate which is 40 mV/s. CAUTION The regulator output voltage cannot be ensured if a slow-moving AC (or DC) signal is applied that is in the range between the specified turn-on and turn-off voltages listed under the electrical specification VON/OFF (see Electrical Characteristics). 8.2.2.4 Reverse Input-Output Voltage The PNP power transistor used as the pass element in the LP2985-N has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse-biased). VIN VOUT PNP GND Figure 23. Reverse Current Path SCHOTTKY DIODE VIN VOUT PNP GND Figure 24. Reverse Current Protection However, if the output voltage is higher than the input voltage, this diode turns ON, and current flows into the regulator OUT pin. In such cases, a parasitic SCR can latch, allowing a high current to flow into the IN pin and out the ground (GND) pin, which can damage the device. In any application where the voltage at the OUT pin may possibly be higher than the voltage at the IN pin, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2985-N to 0.3 V (see Absolute Maximum Ratings). 8.2.2.5 Power Dissipation Knowing the device power dissipation and proper sizing of the thermal plane connected to the tab or pad is critical to ensuring reliable operation. Device power dissipation depends on input voltage, output voltage, and load conditions and can be calculated with Equation 1. PD(MAX) = (VIN(MAX) - VOUT) x IOUT(MAX) 18 (1) Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Power dissipation can be minimized, and greater efficiency can be achieved, by using the lowest available voltage drop option that would still be greater than the dropout voltage (VDO). However, keep in mind that higher voltage drops result in better dynamic (that is, PSRR and transient) performance. On the SOT-23 (DBV) package, the primary conduction path for heat is through the device leads to the PCB, predominately device lead 2 (GND). TI recommends that the trace from lead 2 be extended under the package body and connected to an internal ground plane with thermal vias. The maximum allowable junction temperature (TJ(MAX)) determines maximum power dissipation allowed (PD(MAX)) for the device package. Power dissipation and junction temperature are most often related by the junction-to-ambient thermal resistance (RJA) of the combined PCB and device package and the temperature of the ambient air (TA), according to Equation 2 or Equation 3: TJ(MAX) = TA(MAX) + (RJA x PD(MAX)) PD(MAX) = (TJ(MAX) - TA(MAX)) / RJA (2) (3) Unfortunately, this RJA is highly dependent on the heat-spreading capability of the particular PCB design, and therefore varies according to the total copper area, copper weight, and location of the planes. The RJA recorded in Thermal Information is determined by the specific EIA/JEDEC JESD51-7 standard for PCB and copperspreading area, and is to be used only as a relative measure of package thermal performance. For a welldesigned thermal layout, RJA is actually the sum of the package junction-to-case (bottom) thermal resistance (RJCbot) plus the thermal resistance contribution by the PCB copper area acting as a heat sink. 8.2.2.6 Estimating Junction Temperature The EIA/JEDEC standard recommends the use of psi () thermal characteristics to estimate the junction temperatures of surface mount devices on a typical PCB board application. These characteristics are not true thermal resistance values, but rather package specific thermal characteristics that offer practical and relative means of estimating junction temperatures. These psi metrics are determined to be significantly independent of copper-spreading area. The key thermal characteristics (JT and JB) are given in Thermal Information and are used in accordance with Equation 4 or Equation 5. TJ(MAX) = TTOP + (JT x PD(MAX)) where * * PD(MAX) is explained in Equation 1. TTOP is the temperature measured at the center-top of the device package. (4) TJ(MAX) = TBOARD + (JB x PD(MAX)) where * * PD(MAX) is explained in Equation 1. TBOARD is the PCB surface temperature measured 1-mm from the device package and centered on the package edge. (5) For more information about the thermal characteristics JT and JB, see Semiconductor and IC Package Thermal Metrics, available for download at www.ti.com. For more information about measuring TTOP and TBOARD, see Using New Thermal Metrics; and for more information about the EIA/JEDEC JESD51 PCB used for validating RJA, see Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs. These application notes are available at www.ti.com.com. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 19 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com 8.2.3 Application Curves 20 Figure 25. Short-Circuit Current Figure 26. Short-Circuit Current Figure 27. Load Transient Response Figure 28. Load Transient Response Figure 29. Load Transient Response Figure 30. Line Transient Response Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 Figure 31. Line Transient Response Figure 33. Line Transient Response Figure 35. Turn-On Time Figure 32. Line Transient Response Figure 34. Line Transient Response Figure 36. Turnon Time Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 21 LP2985-N SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 www.ti.com Figure 37. Turnon Time Figure 38. Turnon Time 9 Power Supply Recommendations The LP2985-N is designed to operate from an input voltage supply range between VIN of 2.5 V and 16 V. (Recommended minimum VIN is the greater of 3.1 V or VOUT(max) + rated dropout voltage (max) for operating load current.) The input voltage range provides adequate headroom in order for the device to have a regulated output. This input supply must be well regulated. If the input supply is noisy, additional input capacitors with low ESR can help to improve the output noise performance. 10 Layout 10.1 Layout Guidelines For best overall performance, place all circuit components on the same side of the circuit board and as near as practical to the respective LDO pin connections. Place ground return connections to the input and output capacitor, and to the LDO ground pin as close as possible to each other, connected by a wide, component-side, copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise, and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this ground plane is necessary to meet thermal requirements. 10.2 Layout Example VIN Input Capacitor VOUT IN OUT Output Capacitor GND Ground Bypass Capacitor ON/OFF BYPASS Figure 39. LP2985 SOT-23 Package Typical Layout 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N LP2985-N www.ti.com SNVS018Y - MARCH 2000 - REVISED DECEMBER 2016 11 Device and Documentation Support 11.1 Documentation Support 11.1.1 Related Documentation * Semiconductor and IC Package Thermal Metrics * Using New Thermal Metrics * Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs 11.2 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2985-N 23 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2985AIM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAUA LP2985AIM5-2.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LALA LP2985AIM5-2.8 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0KA LP2985AIM5-2.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0KA LP2985AIM5-2.9/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAXA LP2985AIM5-3.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0OA LP2985AIM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0OA LP2985AIM5-3.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0PA LP2985AIM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0RA LP2985AIM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0RA LP2985AIM5-3.6 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0SA LP2985AIM5-3.6/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0SA LP2985AIM5-3.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0YA LP2985AIM5-4.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0TA LP2985AIM5-4.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA7A LP2985AIM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0UA LP2985AIM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0UA LP2985AIM5-5.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP2985AIM5-6.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM Addendum-Page 1 LKTA -40 to 125 LF6A Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2985AIM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAUA LP2985AIM5X-2.6/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCEA LP2985AIM5X-2.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0KA LP2985AIM5X-2.9/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAXA LP2985AIM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0OA LP2985AIM5X-3.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0PA LP2985AIM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0RA LP2985AIM5X-3.6/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0SA LP2985AIM5X-3.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0YA LP2985AIM5X-4.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0TA LP2985AIM5X-4.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA7A LP2985AIM5X-5.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L0UA LP2985AIM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0UA LP2985AIM5X-6.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LF6A LP2985IM5-2.5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 LAUB LP2985IM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAUB LP2985IM5-2.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP2985IM5-2.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0KB LP2985IM5-2.9/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAXB Addendum-Page 2 LALB Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2985IM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0OB LP2985IM5-3.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0PB LP2985IM5-3.2/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0QB LP2985IM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0RB LP2985IM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0RB LP2985IM5-3.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAIB LP2985IM5-3.6/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0SB LP2985IM5-3.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0YB LP2985IM5-4.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0TB LP2985IM5-4.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LA7B LP2985IM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0UB LP2985IM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0UB LP2985IM5-5.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LKTB LP2985IM5-6.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LF6B LP2985IM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP2985IM5X-2.7/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP2985IM5X-2.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0KB LP2985IM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0OB LP2985IM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0RB Addendum-Page 3 -40 to 125 LAUB LALB Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2985IM5X-3.6/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0SB LP2985IM5X-4.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0TB LP2985IM5X-4.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LP2985IM5X-5.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L0UB LP2985IM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0UB LA7B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2018 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LP2985AIM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 LP2985AIM5-2.7/NOPB SOT-23 DBV 5 1000 178.0 LP2985AIM5-2.8 SOT-23 DBV 5 1000 178.0 LP2985AIM5-2.8/NOPB SOT-23 DBV 5 1000 LP2985AIM5-2.9/NOPB SOT-23 DBV 5 W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.6 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.6/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-3.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-4.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-4.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5-5.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2018 Device LP2985AIM5-6.1/NOPB Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-2.6/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-2.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-2.9/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-3.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-3.6/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-3.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-4.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-4.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985AIM5X-6.1/NOPB SOT-23 LP2985AIM5X-5.0 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.9/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.2/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.6/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-3.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-4.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-4.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-5.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-6.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-2.7/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-2.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-3.6/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-4.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-4.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-5.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2018 Device LP2985IM5X-5.0/NOPB Package Package Pins Type Drawing SPQ SOT-23 3000 DBV 5 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 178.0 8.4 3.2 B0 (mm) K0 (mm) P1 (mm) 3.2 1.4 4.0 W Pin1 (mm) Quadrant 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2985AIM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-2.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-2.8 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-2.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-2.9/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.6 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.6/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-3.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-4.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-4.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 Pack Materials-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2018 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2985AIM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-5.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-6.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-2.6/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-2.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-2.9/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-3.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-3.6/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-3.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-4.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-4.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-6.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5-2.5 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.9/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.2/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.6/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-3.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-4.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-4.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-5.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-6.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-2.7/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-2.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-3.6/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-4.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-4.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2018 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2985IM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 5 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LP2985AIM5-2.5/NOPB LP2985AIM5-2.7/NOPB LP2985AIM5-2.8 LP2985AIM5-2.8/NOPB LP2985AIM5-2.9/NOPB LP2985AIM5-3.0 LP2985AIM5-3.0/NOPB LP2985AIM5-3.1/NOPB LP2985AIM5-3.3 LP2985AIM5-3.3/NOPB LP2985AIM5-3.6 LP2985AIM5-3.6/NOPB LP2985AIM5-3.8/NOPB LP2985AIM5-4.0 LP2985AIM5-4.0/NOPB LP2985AIM5-4.5 LP2985AIM5-4.5/NOPB LP2985AIM5-5.0 LP2985AIM5-5.0/NOPB LP2985AIM5-6.1/NOPB LP2985AIM5X-2.5 LP2985AIM5X-2.5/NOPB LP2985AIM5X-2.6/NOPB LP2985AIM5X-2.7/NOPB LP2985AIM5X2.8/NOPB LP2985AIM5X-2.9/NOPB LP2985AIM5X-3.0 LP2985AIM5X-3.0/NOPB LP2985AIM5X-3.1/NOPB LP2985AIM5X-3.3 LP2985AIM5X-3.3/NOPB LP2985AIM5X-3.6/NOPB LP2985AIM5X-3.8/NOPB LP2985AIM5X4.0/NOPB LP2985AIM5X-4.5/NOPB LP2985AIM5X-5.0 LP2985AIM5X-5.0/NOPB LP2985AIM5X-6.1/NOPB LP2985AITL-3.3/NOPB LP2985AITLX-3.3/NOPB LP2985AITP-2.6/NOPB LP2985AITP-2.7/NOPB LP2985AITP2.8/NOPB LP2985AITP-2.9/NOPB LP2985AITP-3.0/NOPB LP2985AITP-3.3/NOPB LP2985AITP-5.0/NOPB LP2985AITPX-2.5/NOPB LP2985AITPX-2.6/NOPB LP2985AITPX-2.7/NOPB LP2985AITPX-2.8/NOPB LP2985AITPX-2.9/NOPB LP2985AITPX-3.0/NOPB LP2985AITPX-3.3/NOPB LP2985AITPX-5.0/NOPB LP2985IM52.5 LP2985IM5-2.5/NOPB LP2985IM5-2.7/NOPB LP2985IM5-2.8/NOPB LP2985IM5-2.9/NOPB LP2985IM53.0/NOPB LP2985IM5-3.1/NOPB LP2985IM5-3.2/NOPB LP2985IM5-3.3 LP2985IM5-3.3/NOPB LP2985IM53.5/NOPB LP2985IM5-3.6 LP2985IM5-3.6/NOPB LP2985IM5-3.8 LP2985IM5-3.8/NOPB LP2985IM5-4.0/NOPB LP2985IM5-4.5/NOPB LP2985IM5-5.0 LP2985IM5-5.0/NOPB LP2985IM5-6.1/NOPB LP2985IM5X-2.5/NOPB LP2985IM5X-2.7/NOPB LP2985IM5X-2.8/NOPB LP2985IM5X-2.9/NOPB LP2985IM5X-3.0 LP2985IM5X-3.0/NOPB LP2985IM5X-3.1/NOPB LP2985IM5X-3.3/NOPB LP2985IM5X-3.6/NOPB LP2985IM5X-3.8/NOPB LP2985IM5X4.0/NOPB LP2985IM5X-4.5/NOPB LP2985IM5X-5.0 LP2985IM5X-5.0/NOPB LP2985IM5X-6.1/NOPB LP2985ITL3.3/NOPB LP2985ITLX-3.3/NOPB LP2985ITP-2.5/NOPB LP2985ITP-2.6/NOPB LP2985ITP-2.7/NOPB LP2985ITP2.8/NOPB LP2985ITP-2.9/NOPB LP2985ITP-3.0/NOPB LP2985ITP-3.3/NOPB LP2985ITP-5.0/NOPB