Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
LP2989 Micropower and Low-Noise, 500-mA Ultra Low-Dropout Regulator for Use With
Ceramic Output Capacitors
1 Features 3 Description
The LP2989 is a fixed-output 500-mA precision LDO
1 2.1-V to 16-V Input Voltage Range regulator designed for use with ceramic output
2.5-V to 5-V Fixed Output Voltage Options capacitors.
Ultra-Low Dropout Voltage Output noise can be reduced to 18 μV (typical) by
500-mA Continuous Output Current connecting an external 10-nF capacitor to the bypass
Very Low Output Noise With External Capacitor pin.
< 0.8-µA Quiescent Current When Shutdown Using an optimized Vertically Integrated PNP (VIP)
Low Ground Pin Current at All Loads process, the LP2989 delivers superior performance:
Dropout Voltage: Typically 310 mV at 500-mA
0.75% Output Voltage Accuracy (A Grade) load, and 1 mV at 100-µA load.
High Peak Current Capability (800-mA typical) Ground Pin Current: Typically 3 mA at 500-mA
Overtemperature and Overcurrent Protection load, and 110 µA at 100-µA load.
40°C to 125°C Junction Temperature Range Sleep Mode: The LP2989 draws less than 0.8-µA
quiescent current when SHUTDOWN pin is pulled
2 Applications low.
Notebooks and Desktop PCs Error Flag: The built-in error flag goes low when
the output drops approximately 5% below
PDAs and Palmtop Computers nominal.
Wireless Communication Pins Precision Output: Output voltage accuracy is
SMPS Post-Regulators 0.75% (A grade) and 1.25% (standard grade) at
room temperature.
For output voltages < 2 V, see LP2989LV (SNVS086)
data sheet.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
WSON (8) 4.00 mm x 4.00 mm
LP2989 SOIC (8) 4.90 mm x 3.91 mm
VSSOP (8) 3.00 mm x 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application
*Capacitance values shown are minimum required to assure stability, but may be increased without limit. Larger
output capacitor provides improved dynamic response. See the Output Capacitor section.
**Shutdown must be actively terminated (see the Shutdown Input Operation section). Tie to IN (pin 4) if not use.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Table of Contents
7.3 Feature Description................................................. 14
1 Features.................................................................. 17.4 Device Functional Modes........................................ 15
2 Applications ........................................................... 18 Application and Implementation ........................ 16
3 Description............................................................. 18.1 Application Information............................................ 16
4 Revision History..................................................... 28.2 Typical Application ................................................. 16
5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 20
6 Specifications......................................................... 410 Layout................................................................... 20
6.1 Absolute Maximum Ratings ...................................... 410.1 Layout Guidelines ................................................. 20
6.2 ESD Ratings.............................................................. 410.2 Layout Example .................................................... 20
6.3 Recommended Operating Conditions....................... 511 Device and Documentation Support................. 21
6.4 Thermal Information.................................................. 511.1 Documentation Support ....................................... 21
6.5 Electrical Characteristics........................................... 511.2 Trademarks........................................................... 21
6.6 Typical Characteristics.............................................. 711.3 Electrostatic Discharge Caution............................ 21
7 Detailed Description............................................ 14 11.4 Glossary................................................................ 21
7.1 Overview................................................................. 14 12 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram....................................... 14 Information........................................................... 22
4 Revision History
Changes from Revision N (December 2014) to Revision O Page
Changed 30-V to 16-V ........................................................................................................................................................... 1
Deleted trademark symbol from VIP which is no longer trademarked .................................................................................. 1
Changed pin names to TI nomenclature; references to National to TI; add notes to Typical Application on first page;
fix errors in EC table reformat; replace Handling Ratings with ESD Ratings; take out Output Voltage Options and
add graphic to Mechanical section; changed LLP package name references to WSON; added overbar to
SHUTDOWN pin references; fix ulink for LP2989LV references. .......................................................................................... 1
Changed description of N/C pin; add description of Thermal Pad; change "Ground" to "Thermal Pad" for NGN
drawing .................................................................................................................................................................................. 3
Changed reference to National to TI ..................................................................................................................................... 4
Deleted "Operating" row from Input supply voltage; thermal values from footnote 2 ............................................................ 4
Changed 1.6 to 16 in ROC input supply voltage ................................................................................................................... 5
Added word "OFF" ................................................................................................................................................................. 6
Changed "high" to "low" ....................................................................................................................................................... 14
Changed wording of "Operation with Shutdown Control" subsection ................................................................................. 15
Changed VON/OFF to VSD ....................................................................................................................................................... 15
Changed "guaranteed" to "ensured" in "CAUTION"............................................................................................................. 15
Changed VON/OFF to VSD ....................................................................................................................................................... 15
Changed wording of last sentence of introductory Detailed Design Procedure paragraph ................................................ 17
Changed words "size" and "amount" for capacitors to "value" ............................................................................................ 17
Changed wording of first sentence, second paragraph of Noise Bypass Capacitor subsection ......................................... 18
Added Documentation Support section ............................................................................................................................... 21
Changes from Revision M (February 2005) to Revision N Page
Added Handling Rating table, Feature Description section, Device Functional Modes,Application and
Implementation section,Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section; add updated Thermal Information
values .................................................................................................................................................................................... 1
2Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
5 Pin Configuration and Functions
D/DGK Packages NGN Package
8-Pin SOIC and VSSOP 8-Lead WSON
Top View Top View
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
BYPASS 1 I Bypass capacitor input
ERROR 7 O Error signal output
GROUND 3 GND
INPUT 4 I Regulator power input
DO NOT CONNECT. Device pin 2 is reserved for post packaging test and calibration of the
LP2989 VOUT accuracy. Device pin 2 must be left floating. Do not connect to any potential.
Do not connect to ground. Any attempt to do pin continuity testing on device pin 2 is
N/C 2 discouraged. Continuity test results will be variable depending on the actions of the factory
calibration. Aggressive pin continuity testing (high voltage, or high current) on device pin 2
may activate the trim circuitry forcing VOUT to move out of tolerance.
OUTPUT 5 O Regulated output voltage
SENSE 6 I Feedback voltage sense input
SHUTDOWN 8 I Shutdown input
The exposed thermal pad on the bottom of the WSON package should be connected to a
copper thermal pad on the PCB under the package. The use of thermal vias to remove heat
from the package into the PCB is recommended. Connect the thermal pad to ground
Thermal Pad potential or leave floating. Do not connect the thermal pad to any potential other than the
same ground potential seen at device pin 3. For additional information on using TI's Non Pull
Back WSON package, see Application Note AN-1187 Leadless Leadframe Package (LLP)
(SNOA401).
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
If Military/Aerospace specified devices are required contact the Texas Instruments Sales Office/Distributors for availability and
specifications.(1)
MIN MAX UNIT
Operating junction temperature –40 125 °C
Power dissipation(2) Internally Limited
Input supply voltage Survival –0.3 16 V
SENSE pin –0.3 6 V
Output voltage Survival(3) –0.3 16 V
IOUT (Survival) Short-circuit protected
Input-output voltage Survival(4) –0.3 16 V
Storage temperature range, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, RθJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using: P(MAX) = (TJ(MAX) TA) / RθJA. The value RθJA for the WSON (NGN) package is specifically dependent on PCB trace area, trace
material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the WSON package,
refer to Application Note AN-1187 Leadless Leadframe Package (LLP) (SNOA401).. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown.
(3) If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2989 output must be diode-clamped to
ground.
(4) The output PNP structure contains a diode between the IN and OUT pins that is normally reverse-biased. Forcing the output above the
input will turn on this diode and may induce a latch-up mode which can damage the part.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
4Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
Operating junction temperature –40 125 °C
Operating input supply voltage 2.1 16 V
6.4 Thermal Information LP2989
THERMAL METRIC(1) WSON (NGN) SOIC (D) VSSOP (DGK) UNIT
8 PINS 8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance, High-K 34.8 114.5 156.5
RθJC(top) Junction-to-case (top) thermal resistance 28.4 61.1 51.0
RθJB Junction-to-board thermal resistance 12.0 55.6 76.5 °C/W
ψJT Junction-to-top characterization parameter 0.2 9.7 4.9
ψJB Junction-to-board characterization parameter 12.2 54.9 75.2
RθJC(bot) Junction-to-case (bottom) thermal resistance 1.3 n/a n/a
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Electrical Characteristics
Unless otherwise specified: TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VSD = 2 V.
LP2989AI-X.X(1) LP2989I-X.X(1)
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
0.75 0.75 1.25 1.25
1 mA < IOUT < 500 mA,
VOUT(NOM) + 1 V VIN 16 1.5 1.5 2.5 2.5
V
1 mA < IOUT < 500 mA,
VOUT Output voltage tolerance %VNOM
VOUT(NOM) + 1 V VIN 16 4 2.5 5 3.5
V, –40°C TJ125°C
1 mA < IOUT < 500 mA,
VOUT(NOM) + 1 V VIN 16 3.5 2.5 4.5 3.5
V, 25°C TJ125°C
VOUT(NOM) + 1 V VIN 16 0.005 0.014 0.005 0.014
V
Output voltage line
ΔVOUT/ΔVIN %/V
regulation VOUT(NOM) + 1 V VIN 16 0.005 0.032 0.005 0.032
V, –40°C TJ125°C
ΔVOUT/ΔIOUT Load regulation 1 mA < IOUT < 500 mA 0.4 0.4 %VNOM
IOUT = 100 µA 1 3 1 3 mV
IOUT = 100 µA, –40°C TJ1 4 1 4
125°C
IOUT = 200 mA 150 200 150 200
VIN VOUT Dropout voltage(2) mV
IOUT = 200 mA, –40°C TJ150 300 150 300
125°C
IOUT = 500 mA 310 425 310 425 mV
IOUT = 500 mA, –40°C TJ310 650 310 650
125°C
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control (SQC) methods. The limits are used to calculate TI’s Average Outgoing Quality Level (AOQL).
(2) Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a
1-V differential.
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Electrical Characteristics (continued)
Unless otherwise specified: TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VSD = 2 V.
LP2989AI-X.X(1) LP2989I-X.X(1)
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
IOUT = 100 µA 110 175 110 175 µA
IOUT = 100 µA, –40°C TJ110 200 110 200
125°C
IOUT= 200 mA 1 2 1 2 mA
IOUT = 200 mA, –40°C TJ1 3.5 1 3.5
125°C
IGND Ground pin current IOUT = 500 mA 3 6 3 6 mA
IOUT = 500 mA, –40°C TJ3 9 3 9
125°C
VSD < 0.18 V, –40°C TJ0.5 2 0.5 2
125°C µA
VSD < 0.4 V 0.05 0.8 0.05 0.8
IOUT(PK) Peak output current VOUT VOUT(NOM) 5% 600 800 600 800 mA
IOUT(MAX) Short circuit current RL= 0 (Steady State)(3) 1000 1000 mA
BW = 100 Hz to 100 kHz,
Output noise voltage
enCOUT = 10 µF, CBYPASS = 18 18 µV(RMS)
(RMS) .01 µF, VOUT = 2.5 V
ΔVOUT/ΔVIN Ripple Rejection f = 1 kHz, COUT = 10 µF 60 60 dB
Output voltage
ΔVOUT/ΔTDSee(4), –40°C TJ125°C 20 20 ppm/°C
temperature coefficient
SHUTDOWN INPUT
VH= Output ON 1.4 1.4
VH= Output ON, –40°C TJ1.6 1.6
125°C
VSD SD Input voltage V
VL= Output OFF 0.5 0.5
VL= Output OFF, IIN 2 µA, 0.18 0.18
–40°C TJ125°C
VSD = 0 0.001 0.001
VSD = 0, –40°C TJ11
125°C
ISD SD Input current µA
VSD = 5 V 5 5
VSD = 5 V, –40°C TJ15 15
125°C
ERROR COMPARATOR
VOH = 16 V 0.001 1 0.001 1
IOH Output “HIGH” leakage µA
VOH = 16 V, –40°C TJ0.001 2 0.001 2
125°C
VIN = VOUT(NOM) 0.5 V, 150 220 150 220
IOUT(COMP) = 150 µA
VOL Output “LOW” voltage mV
VIN = VOUT(NOM) 0.5 V,
IOUT(COMP) = 150 µA, –40°C 150 350 150 350
TJ125°C
64.8 3.5 64.8 3.5
VTHR(MAX) Upper threshold voltage %VOUT
–40°C TJ125°C 8.3 4.8 2.5 8.3 4.8 2.5
8.9 6.6 4.9 8.9 6.6 4.9
VTHR(MIN) Lower threshold voltage –40°C TJ125°C 13 6.6 313 6.6 3 %VOUT
HYST Hysteresis 2
(3) See the Typical Characteristics section.
(4) Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range.
6Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
6.6 Typical Characteristics
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 2. Dropout Voltage vs Temperature
Figure 1. Dropout Characteristics
Figure 4. GND Pin Current vs Temperature and Load
Figure 3. Dropout Voltage vs Load Current
Figure 5. Ground Pin Current vs Load Current Figure 6. Input Current vs VIN
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 7. Input Current vs VIN Figure 8. Input Current vs VIN
Figure 9. Line Transient Response Figure 10. Line Transient Response
Figure 11. Line Transient Response Figure 12. Line Transient Response
8Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 13. Load Transient Response Figure 14. Load Transient Response
Figure 16. Short Circuit Current vs Temperature
Figure 15. Short Circuit Current
Figure 17. Short Circuit Current Figure 18. Short Circuit Current vs VOUT
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 19. Ripple Rejection Figure 20. Ripple Rejection
Figure 21. Ripple Rejection Figure 22. Ripple Rejection
Figure 23. Ripple Rejection Figure 24. Ripple Rejection
10 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 26. Ripple Rejection in Dropout
Figure 25. Ripple Rejection
Figure 28. Output Noise Density
Figure 27. Ripple Rejection vs Load
Figure 30. Turn-ON Waveform
Figure 29. Output Noise Density
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 31. Turn-ON Waveform Figure 32. Turn-ON Waveform
Figure 33. Turn-ON Waveform Figure 34. IGND vs Shutdown
Figure 35. IGND vs Shutdown Figure 36. IGND vs Shutdown
12 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
Typical Characteristics (continued)
TA= 25°C, COUT = 4.7 µF, CIN = 2.2 µF, SD is tied to VIN, VIN = VOUT(NOM)+ 1 V, IOUT = 1 mA, VOUT = 2.5 V (unless otherwise
specified)
Figure 38. VOUT vs Shutdown
Figure 37. IGND vs Shutdown
Figure 39. Typical Temperature vs VOUT (LP2989-2.5)
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LP2989 device is a very high-accuracy micro-power voltage regulator with low quiescent current (75 μA
typical) and low dropout voltage (typical 40 mV at light loads and 380 mV at 100 mA). It is ideally suited for use
in battery-powered systems. The LP2989 block diagram contains several features, including:
Very high-accuracy 1.23-V reference
Fixed 2.5-V to 5-V versions
Shutdown input
Error flag output
Internal protection circuitry, such as foldback current limit, and thermal shutdown
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 High-Accuracy Output Voltage
With special careful design to minimize all contributions to the output voltage error, the LP2989 distinguishes
itself as a very high output-voltage-accuracy micro-power LDO. This includes a tight initial tolerance (.75%
typical, A grade), extremely good line regulation (.005%/V typical), and a very low output-noise voltage (10 µVRMS
typical), making the device an ideal a low-power voltage reference.
7.3.2 Sleep Mode
When pulling SHUTDOWN pin to low levels, the LP2989 enters shutdown mode, and a very low quiescent
current is consumed. This function is designed for applications which needs a shutdown mode to effectively
enhance battery life cycle.
7.3.3 Error Detection Comparator Output
The LP2989 will generate a logic low output whenever its output falls out of regulation by more than
approximately 5%. Refer to Application and Implementation for more details.
14 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
Feature Description (continued)
7.3.4 Short Circuit Protection (Current Limit)
The internal current limit circuit is used to protect the LDO against high-load current faults or shorting events. The
LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources
constant current. Therefore, the output voltage falls when load impedance decreases. Note also that if a current
limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO, resulting
in a thermal shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from
damage under all load conditions. If OUT is forced below 0 V before EN goes high and the load current required
exceeds the foldback current limit, the device may not start correctly.
7.3.5 Thermal Protection
The device contains a thermal shutdown protection circuit to turn off the output current when excessive heat is
dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output
cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The
internal protection circuitry of the device is designed to protect against thermal overload conditions. The circuitry
is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown degrades
its reliability.
7.4 Device Functional Modes
7.4.1 Operation With 16 V VIN > VOUT(TARGET) +1V
The device operates if the input voltage is equal to, or exceeds VOUT(TARGET) + 1 V. At input voltages below the
minimum VIN requirement, the devices does not operate correctly, and output voltage may not reach target value.
7.4.2 Operation with Shutdown Control
If the voltage on the SHUTDOWN pin is less than 0.18 V, the output is ensured to be OFF. When the voltage on
the SHUTDOWN pin is more than 1.6 V the output is ensured to be ON. Operating with the SHUTDOWN pin
voltage between 0.18 V and 1.6 V is strongly discouraged as the status of the output is not ensured.
7.4.3 Shutdown Input Operation
The LP2989 is shut off by driving the SHUTDOWN pin low, and turned on by pulling it high. If this feature is not
to be used, the SHUTDOWN should be tied to VIN to keep the regulator output on at all times.
To assure proper operation, the signal source used to drive the Shutdown input must be able to swing above and
below the specified turn-on/turn-off voltage thresholds listed in the Electrical Characteristics section under VSD.
To prevent mis-operation, the turn-on (and turn-off) voltage signals applied to the Shutdown input must have a
slew rate which is 40 mV/µs.
CAUTION
The regulator output voltage cannot be ensured if a slow-moving AC (or DC) signal is
applied that is in the range between the specified turn-on and turn-off voltages listed
under the electrical specification VSD (see the Electrical Characteristics table).
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP2989 is a linear voltage regulator operating from 2.1 V to 16 V on the input and regulates voltages
between 2.5 V to 5 V with 0.75% accuracy and 500 mA maximum outputs current. Efficiency is defined by the
ratio of output voltage to input voltage because the LP2989 is a linear voltage regulator. To achieve high
efficiency, the dropout voltage (VIN VOUT) must be as small as possible, thus requiring a very low dropout LDO.
Successfully implementing an LDO in an application depends on the application requirements. If the
requirements are simply input voltage and output voltage, compliance specifications (such as internal power
dissipation or stability) must be verified to ensure a solid design. If timing, start-up, noise, PSRR, or any other
transient specification is required, the design becomes more challenging. This section discusses the
implementation and behavior of the LP2989 LDO.
8.2 Typical Application
*Capacitance values shown are minimum required to assure stability, but may be increased without limit. Larger
output capacitor provides improved dynamic response. See the Output Capacitor section.
**Shutdown must be actively terminated (see the Shutdown Input Operation section). Tie to IN (pin 4) if not use.
Figure 40. Typical Application Schematic
8.2.1 Design Requirements
DESIGN PARAMETER DESIGN REQUIREMENT
Input voltage 6.5 V, ±10%,
Output voltage 5 V, ±1%
Output current 500 mA (maximum), 1 mA (minimum)
RMS noise, 100 Hz to 100 kHz 18 μVRMS typical
PSRR at 1 kHz 60 dB typical
16 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
8.2.2 Detailed Design Procedure
At 500-mA loading, the dropout of the LP2989 has 650-mV maximum dropout over temperature, thus an 1500-
mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the
LP2989 in this configuration is VOUT / VIN = 76.9%. To achieve the smallest form factor, the WSON package is
selected. Input and output capacitors are selected in accordance with the capacitor recommendations. Ceramic
capacitances of 2.2 μF for the input and one 4.7-μF capacitor for the output are selected. With an efficiency of
76.9% and a 500-mA maximum load, the internal power dissipation is 750 mW, which corresponds to a 26.1°C
junction temperature rise for the WSON package. With an 85°C maximum ambient temperature, the junction
temperature is at 111.1°C. To minimize noise, a bypass capacitance (CBYPASS) of 0.01 µF is placed from the
BYPASS pin (device pin 1) to device ground (device pin 3).
8.2.2.1 WSON Package Devices
The LP2989 is offered in the 8-lead WSON surface mount package to allow for increased power dissipation
compared to the SOIC and VSSOP packages. For details on thermal performance as well as mounting and
soldering specifications, refer to Application Note AN-1187 Leadless Leadframe Package (LLP) (SNOA401).
For output voltages < 2 V, see LP2989LV (SNVS086) data sheet.
8.2.2.2 External Capacitors
Like any low-dropout regulator, the LP2989 requires external capacitors for regulator stability. These capacitors
must be correctly selected for good performance.
8.2.2.2.1 Input Capacitor
An input capacitor whose value is at least 2.2 µF is required between the LP2989 input and ground (the amount
of capacitance may be increased without limit).
Characterization testing performed on the LP2989 has shown that if the value of actual input capacitance drops
below about 1.5 µF, an unstable operating condition may result. Therefore, the next larger standard size (2.2 µF)
is specified as the minimum required input capacitance. Capacitor tolerance and temperature variation must be
considered when selecting a capacitor (see Capacitor Characteristics section) to assure the minimum
requirement of 1.5 µF is met over all operating conditions.
The input capacitor must be located at a distance of not more than 0.5 inches from the input pin and returned to
a clean analog ground. Any good quality ceramic or tantalum may be used for this capacitor, assuming the
minimum capacitance requirement is met.
8.2.2.2.2 Output Capacitor
The LP2989 requires a ceramic output capacitor whose value is at least 4.7 µF. The actual amount of
capacitance on the output must never drop below about 3.5 µF or unstable operation may result. For this reason,
capacitance tolerance and temperature characteristics must be considered when selecting an output capacitor.
The LP2989 is designed specifically to work with ceramic output capacitors, using circuitry which allows the
regulator to be stable across the entire range of output current with an output capacitor whose ESR is as low as
4 mΩ. It may also be possible to use Tantalum or film capacitors at the output, but these are not as attractive for
reasons of size and cost (see the Capacitor Characteristics section).
The output capacitor must meet the requirement for minimum amount of capacitance and also have an
equivalent series resistance (ESR) value which is within the stable range. Curves are provided which show the
stable ESR range as a function of load current (see Figure 41).
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
Figure 41. Stable Region for Output Capacitor ESR
NOTE
Important: The output capacitor must maintain its ESR within the stable region over the
full operating temperature range of the application to assure stability.
It is important to remember that capacitor tolerance and variation with temperature must be considered when
selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full
operating temperature range. (See the Capacitor Characteristics section.)
The output capacitor must be located not more than 0.5 inches from the OUT pin and returned to a clean analog
ground.
8.2.2.2.3 Noise Bypass Capacitor
Connecting a 10-nF capacitor to the BYPASS pin significantly reduces noise on the regulator output. However,
the capacitor is connected directly to a high-impedance circuit in the bandgap reference.
Because this circuit has only a few microamperes flowing in it, any significant loading on this node will cause the
regulated output voltage to drop. For this reason, DC leakage current through the noise bypass capacitor must
never exceed 100 nA, and should be kept as low as possible for best output voltage accuracy.
The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic
capacitors with either NPO or COG dielectric typically have very low leakage. Ten-nF polypropolene and
polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low
leakage current.
8.2.2.3 Capacitor Characteristics
8.2.2.3.1 Ceramic
The LP2989 was designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer: for capacitance values in the 4.7 µF range, ceramics are the least expensive and also have the lowest ESR
values (which makes them best for eliminating high-frequency noise). The ESR of a typical 4.7-µF ceramic
capacitor is in the range of 10 mto 15 m, which easily meets the ESR limits required for stability by the
LP2989.
One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Many large-value
ceramic capacitors (2.2 µF) are manufactured with the Z5U or Y5V temperature characteristic, which results in
the capacitance dropping by more than 50% as the temperature goes from 25°C to 85°C.
This could cause problems if a 4.7-µF capacitor were used on the output because it will drop down to
approximately 2.4 µF at high ambient temperatures (which could cause the LP2989 to oscillate). Another
significant problem with Z5U and Y5V dielectric devices is that the capacitance drops severely with applied
voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage
applied to it.
18 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
For these reasons, X7R and X5R type ceramic capacitors must be used on the input and output of the LP2989.
8.2.2.3.2 Tantalum
Tantalum capacitors are less desirable than ceramics for use as output capacitors because they are typically
more expensive when comparing equivalent capacitance and voltage ratings in the 1 µF to 4.7 µF range.
Another important consideration is that Tantalum capacitors have higher ESR values than equivalent size
ceramics; while it may be possible to find a Tantalum capacitor with an ESR value within the stable range, it
would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the
same ESR value.
It should also be noted that the ESR of a typical Tantalum will increase about 2:1 as the temperature goes from
25°C down to 40°C, so some guard band must be allowed.
Tantalum capacitors may be used on the input as long as the requirement for minimum capacitance is met.
8.2.2.3.3 Film
Polycarbonate and polypropelene film capacitors have excellent electrical performance: their ESR is the lowest of
the three types listed, their capacitance is very stable with temperature, and DC leakage current is extremely low.
One disadvantage is that film capacitors are larger in physical size than ceramic or tantalum which makes film a
poor choice for either input or output capacitors.
However, their low leakage makes them a good choice for the noise bypass capacitor. Because the required
amount of capacitance is only 0.01 µF, small surface-mount film capacitors are available in this size.
8.2.2.4 Reverse Input-Output Voltage
The PNP power transistor used as the pass element in the LP2989 has an inherent diode connected between
the regulator output and input.
During normal operation (where the input voltage is higher than the output) this diode is reverse-biased.
However, if the output is pulled above the input, this diode will turn on and current will flow into the regulator
output.
In such cases, a parasitic SCR can latch which will allow high current to flow into VIN can damage the part.
In any application where the output may be pulled above the input, an external Schottky diode must be
connected from VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2989 to
0.3 V (see the Absolute Maximum Ratings table).
8.2.3 Application Curves
Figure 43. Load Transient Response
Figure 42. Line Transient Response
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LP2989
Ground
VOUT
VIN
Input
Capacitor
Output
Capacitor
BYPASS
N/C
GROUND
IN OUT
SHUTDOWN
SENSE
ERROR
Error Pullup
Resistor VOUT
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
9 Power Supply Recommendations
The LP2989 is designed to operate from an input voltage supply range from 2.1 V to 16 V. The input voltage
range provides adequate headroom for the device to have a regulated output. This input supply must be well
regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output noise
performance.
10 Layout
10.1 Layout Guidelines
For best overall performance, place all circuit components on the same side of the circuit board and as near as
practical to the respective LDO pin connections. Place ground return connections to the input and output
capacitor, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side,
copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and
negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and
thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference
plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB
opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise,
and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this
ground plane is necessary to meet thermal requirements.
10.2 Layout Example
Figure 44. Layout Example
20 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
LP2989
www.ti.com
SNVS083O FEBRUARY 2005REVISED MARCH 2015
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
LP2989LV (SNVS086) data sheet
Application Note AN-1187 Leadless Leadframe Package (LLP) (SNOA401).
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2005–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LP2989
LP2989
SNVS083O FEBRUARY 2005REVISED MARCH 2015
www.ti.com
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Figure 45. POA Orderable Device Key
22 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: LP2989
PACKAGE OPTION ADDENDUM
www.ti.com 14-Oct-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2989AILD-3.0/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01HA
LP2989AILD-3.3/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01JA
LP2989AILD-5.0 NRND WSON NGN 8 1000 TBD Call TI Call TI -40 to 125 L01KA
LP2989AILD-5.0/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01KA
LP2989AILDX-2.8/NOPB ACTIVE WSON NGN 8 4500 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L000A
LP2989AIM-2.5/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM2.5
LP2989AIM-3.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM3.0
LP2989AIM-3.3/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM3.3
LP2989AIM-5.0 NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 2989A
IM5.0
LP2989AIM-5.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM5.0
LP2989AIMM-2.5/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA0A
LP2989AIMM-3.0/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA1A
LP2989AIMM-3.3/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA2A
LP2989AIMM-5.0/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA4A
LP2989AIMMX-2.5/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA0A
LP2989AIMMX-5.0/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA4A
LP2989AIMX-2.5/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM2.5
PACKAGE OPTION ADDENDUM
www.ti.com 14-Oct-2017
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2989AIMX-3.0/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM3.0
LP2989AIMX-3.3/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM3.3
LP2989AIMX-5.0/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989A
IM5.0
LP2989ILD-2.5/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01FA
B
LP2989ILD-3.0/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01HA
B
LP2989ILD-3.3/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01JA
B
LP2989ILD-5.0/NOPB ACTIVE WSON NGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01KA
B
LP2989ILDX-3.3/NOPB ACTIVE WSON NGN 8 4500 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01JA
B
LP2989ILDX-5.0/NOPB ACTIVE WSON NGN 8 4500 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L01KA
B
LP2989IM-2.5/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM2.5
LP2989IM-3.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM3.0
LP2989IM-3.3 NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 2989
IM3.3
LP2989IM-3.3/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM3.3
LP2989IM-5.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM5.0
LP2989IMM-2.8/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA6B
LP2989IMM-3.0/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA1B
LP2989IMM-3.3/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA2B
LP2989IMM-5.0 NRND VSSOP DGK 8 1000 TBD Call TI Call TI -40 to 125 LA4B
PACKAGE OPTION ADDENDUM
www.ti.com 14-Oct-2017
Addendum-Page 3
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2989IMM-5.0/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA4B
LP2989IMMX-2.8/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA6B
LP2989IMMX-5.0 NRND VSSOP DGK 8 3500 TBD Call TI Call TI -40 to 125 LA4B
LP2989IMMX-5.0/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LA4B
LP2989IMX-2.5/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM2.5
LP2989IMX-3.3/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM3.3
LP2989IMX-5.0/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2989
IM5.0
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 14-Oct-2017
Addendum-Page 4
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP2989AILD-3.0/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989AILD-3.3/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989AILD-5.0 WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989AILD-5.0/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989AILDX-2.8/NOPB WSON NGN 8 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989AIMM-2.5/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMM-3.0/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMM-3.3/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMM-5.0/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMMX-2.5/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMMX-5.0/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989AIMX-2.5/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989AIMX-3.0/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989AIMX-3.3/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989AIMX-5.0/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989ILD-2.5/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989ILD-3.0/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989ILD-3.3/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP2989ILD-5.0/NOPB WSON NGN 8 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989ILDX-3.3/NOPB WSON NGN 8 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989ILDX-5.0/NOPB WSON NGN 8 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
LP2989IMM-2.8/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMM-3.0/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMM-3.3/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMM-5.0 VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMM-5.0/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMMX-2.8/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMMX-5.0 VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMMX-5.0/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LP2989IMX-2.5/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989IMX-3.3/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LP2989IMX-5.0/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2989AILD-3.0/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989AILD-3.3/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989AILD-5.0 WSON NGN 8 1000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 2
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2989AILD-5.0/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989AILDX-2.8/NOPB WSON NGN 8 4500 367.0 367.0 35.0
LP2989AIMM-2.5/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989AIMM-3.0/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989AIMM-3.3/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989AIMM-5.0/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989AIMMX-2.5/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LP2989AIMMX-5.0/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LP2989AIMX-2.5/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989AIMX-3.0/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989AIMX-3.3/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989AIMX-5.0/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989ILD-2.5/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989ILD-3.0/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989ILD-3.3/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989ILD-5.0/NOPB WSON NGN 8 1000 210.0 185.0 35.0
LP2989ILDX-3.3/NOPB WSON NGN 8 4500 367.0 367.0 35.0
LP2989ILDX-5.0/NOPB WSON NGN 8 4500 367.0 367.0 35.0
LP2989IMM-2.8/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989IMM-3.0/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989IMM-3.3/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989IMM-5.0 VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989IMM-5.0/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LP2989IMMX-2.8/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LP2989IMMX-5.0 VSSOP DGK 8 3500 367.0 367.0 35.0
LP2989IMMX-5.0/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LP2989IMX-2.5/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989IMX-3.3/NOPB SOIC D 8 2500 367.0 367.0 35.0
LP2989IMX-5.0/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 3
MECHANICAL DATA
NGN0008A
www.ti.com
LDC08A (Rev B)
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LP2989AILD-2.8 LP2989AILD-2.8/NOPB LP2989AILD-3.0 LP2989AILD-3.0/NOPB LP2989AILD-3.3 LP2989AILD-
3.3/NOPB LP2989AILD-5.0 LP2989AILD-5.0/NOPB LP2989AILDX-2.8 LP2989AILDX-2.8/NOPB LP2989AILDX-3.0
LP2989AILDX-3.0/NOPB LP2989AILDX-3.3 LP2989AILDX-3.3/NOPB LP2989AILDX-5.0 LP2989AILDX-5.0/NOPB
LP2989AIM-2.5 LP2989AIM-2.5/NOPB LP2989AIM-3.0 LP2989AIM-3.0/NOPB LP2989AIM-3.3 LP2989AIM-
3.3/NOPB LP2989AIM-5.0 LP2989AIM-5.0/NOPB LP2989AIMM-2.5/NOPB LP2989AIMM-3.0 LP2989AIMM-
3.0/NOPB LP2989AIMM-3.3 LP2989AIMM-3.3/NOPB LP2989AIMM-5.0 LP2989AIMM-5.0/NOPB LP2989AIMMX-2.5
LP2989AIMMX-2.5/NOPB LP2989AIMMX-3.0 LP2989AIMMX-3.0/NOPB LP2989AIMMX-3.3 LP2989AIMMX-
3.3/NOPB LP2989AIMMX-5.0 LP2989AIMMX-5.0/NOPB LP2989AIMX-1.8 LP2989AIMX-2.5 LP2989AIMX-2.5/NOPB
LP2989AIMX-3.0 LP2989AIMX-3.0/NOPB LP2989AIMX-3.3 LP2989AIMX-3.3/NOPB LP2989AIMX-5.0
LP2989AIMX-5.0/NOPB LP2989ILD-2.5 LP2989ILD-2.5/NOPB LP2989ILD-2.8 LP2989ILD-2.8/NOPB LP2989ILD-3.0
LP2989ILD-3.0/NOPB LP2989ILD-3.3 LP2989ILD-3.3/NOPB LP2989ILD-5.0 LP2989ILD-5.0/NOPB LP2989ILDX-
2.5 LP2989ILDX-2.5/NOPB LP2989ILDX-2.8 LP2989ILDX-2.8/NOPB LP2989ILDX-3.0 LP2989ILDX-3.0/NOPB
LP2989ILDX-3.3 LP2989ILDX-3.3/NOPB LP2989ILDX-5.0 LP2989ILDX-5.0/NOPB LP2989IM-2.5 LP2989IM-
2.5/NOPB LP2989IM-3.0 LP2989IM-3.0/NOPB LP2989IM-3.3 LP2989IM-3.3/NOPB LP2989IM-5.0 LP2989IM-
5.0/NOPB LP2989IMM-2.8 LP2989IMM-2.8/NOPB LP2989IMM-3.0 LP2989IMM-3.0/NOPB LP2989IMM-3.3
LP2989IMM-3.3/NOPB LP2989IMM-5.0 LP2989IMM-5.0/NOPB LP2989IMMX-2.8 LP2989IMMX-2.8/NOPB
LP2989IMMX-3.0 LP2989IMMX-3.0/NOPB LP2989IMMX-3.3 LP2989IMMX-3.3/NOPB LP2989IMMX-5.0
LP2989IMMX-5.0/NOPB LP2989IMX-1.8 LP2989IMX-2.5 LP2989IMX-2.5/NOPB LP2989IMX-3.0 LP2989IMX-
3.0/NOPB LP2989IMX-3.3 LP2989IMX-3.3/NOPB LP2989IMX-5.0