Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Datasheet Product Features Available in 1B GHz, 933, 866, 800EB, 733, 667, 600EB, and 533EB MHz for a 133 MHz system bus Available in 900, 850, 800, 750, 700, 650, 600E, 550E, and 500E MHz for a 100 MHz system bus System bus frequency at 100 MHz and 133 MHz ("E" denotes support for Advanced Transfer Cache and Advanced system buffering; "B" denotes support for a 133MHz system bus where both bus frequencies are available for order per each given core frequency; See Table 1 for a summary of features for each line item.) Available in versions that incorporate 256 KB Advanced Transfer Cache (on-die, full speed Level 2 (L2) cache with Error Correcting Code (ECC)) Dual Independent Bus (DIB) architecture: Separate dedicated external System Bus and dedicated internal high-speed cache bus Internet Streaming SIMD Extensions for enhanced video, sound and 3D performance Binary compatible with applications running on previous members of the Intel microprocessor line Dynamic execution micro architecture Intel Processor Serial Number Power Management capabilities System Management mode Multiple low-power states Optimized for 32-bit applications running on advanced 32-bit operating systems Flip Chip Pin Grid Array (FC-PGA) packaging technology; FC-PGA processors deliver high performance with improved handling protection and socketability Integrated high performance 16 KB instruction and 16 KB data, nonblocking, level one cache 256 KB Integrated Full Speed level two cache allows for low latency on read/store operations Double Quad Word Wide(256bit) cache data bus provides extremely high throughput on read/store operations. 8-way cache associativity provides improved cache hit rate on reads/store operations. Error-correcting code for System Bus data Enables systems which are scaleable for up to two processors The Pentium(R) III processor is designed for high-performance desktops and for workstations and servers. It is binary compatible with previous Intel Architecture processors. The Pentium III processor provides great performance for applications running on advanced operating systems such as Windows* 98, Windows NT and UNIX*. This is achieved by integrating the best attributes of Intel processors-- the dynamic execution, Dual Independent Bus architecture plus Intel MMXTM technology and Internet Streaming SIMD Extentions-- bringing a new level of performance for systems buyers. The Pentium(R) III processor is scaleable to two processors in a multiprocessor system and extends the power of the Pentium(R) II processor with performance headroom for business media, communication and internet capabilities. Systems based on Pentium(R) III processors also include the latest features to simplify system management and lower the cost of ownership for large and small business environments. The Pentium(R) III processor offers great performance for today's and tomorrow's applications. FC-PGA370 Package October 2000 Order Number: 245264-007 Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Pentium(R) III processor may contain design defects or errors known as errata which may cause the product to deviate from published specifcations. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800-548-4725 or by visiting Intel's website at http://www.intel.com. Copyright (c) Intel Corporation, 2000 *Third-party brands and names are the property of their respective owners. Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Contents 1.0 Introduction......................................................................................................................... 7 1.1 1.2 2.0 Electrical Specifications....................................................................................................11 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 3.0 Processor System Bus and VREF ........................................................................11 Clock Control and Low Power States..................................................................12 2.2.1 Normal State--State 1 ...........................................................................13 2.2.2 AutoHALT Powerdown State--State 2...................................................13 2.2.3 Stop-Grant State--State 3 .....................................................................13 2.2.4 HALT/Grant Snoop State--State 4 ........................................................14 2.2.5 Sleep State--State 5..............................................................................14 2.2.6 Deep Sleep State--State 6 ....................................................................14 2.2.7 Clock Control..........................................................................................15 Power and Ground Pins ......................................................................................15 2.3.1 Phase Lock Loop (PLL) Power...............................................................16 Decoupling Guidelines .......................................................................................16 2.4.1 Processor VCCCORE Decoupling............................................................16 2.4.2 Processor System Bus AGTL+ Decoupling............................................16 Processor System Bus Clock and Processor Clocking .......................................17 2.5.1 Mixing Processors of Differrent Frequencies .........................................17 Voltage Identification ...........................................................................................17 Processor System Bus Unused Pins...................................................................19 Processor System Bus Signal Groups ................................................................19 2.8.1 Asynchronous vs. Synchronous for System Bus Signals .......................20 2.8.2 System Bus Frequency Select Signals (BSEL[1:0]) ...............................21 Test Access Port (TAP) Connection....................................................................22 Maximum Ratings................................................................................................22 Processor DC Specifications...............................................................................23 AGTL+ System Bus Specifications .....................................................................29 System Bus AC Specifications ............................................................................29 2.13.1 I/O Buffer Model .....................................................................................30 Signal Quality Specifications ............................................................................................38 3.1 3.2 3.3 Datasheet Terminology........................................................................................................... 8 1.1.1 Package and Processor Terminology ...................................................... 8 1.1.2 Processor Naming Convention.................................................................9 Related Documents.............................................................................................10 BCLK and PICCLK Signal Quality Specifications and Measurement Guidelines 38 AGTL+ Signal Quality Specifications and Measurement Guidelines ..................39 AGTL+ Signal Quality Specifications and Measurement Guidelines ..................40 3.3.1 Overshoot/Undershoot Guidelines .........................................................40 3.3.2 Overshoot/Undershoot Magnitude .........................................................41 3.3.3 Overshoot/Undershoot Pulse Duration...................................................41 3.3.4 Activity Factor .........................................................................................41 3.3.5 Reading Overshoot/Undershoot Specification Tables............................42 3.3.6 Determining if a System meets the Overshoot/Undershoot Specifications .........................................................................................43 3 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 3.4 4.0 Thermal Specifications and Design Considerations......................................................... 47 4.1 5.0 6.2 6.3 Mechanical Specifications for the Boxed Intel(R) Pentium(R) III Processor.............. 64 6.1.1 Boxed Processor Thermal Cooling Solution Dimensions....................... 64 6.1.2 Boxed Processor Heatsink Weight......................................................... 67 6.1.3 Boxed Processor Thermal Cooling Solution Clip ................................... 67 Thermal Specifications........................................................................................ 68 6.2.1 Boxed Processor Cooling Requirements ............................................... 68 Electrical Requirements for the Boxed Intel(R) Pentium(R) III Processor................. 69 6.3.1 Fan Heatsink Power Supply ................................................................... 69 Processor Signal Description ........................................................................................... 71 7.1 7.2 4 FC-PGA Mechanical Specifications .................................................................... 50 Processor Markings ............................................................................................ 52 Processor Signal Listing...................................................................................... 52 Boxed Processor Specifications....................................................................................... 64 6.1 7.0 Thermal Specifications........................................................................................ 47 4.1.1 Thermal Diode........................................................................................ 48 Mechanical Specifications............................................................................................... 50 5.1 5.2 5.3 6.0 Non-AGTL+ Signal Quality Specifications and Measurement Guidelines........... 45 3.4.1 Overshoot/Undershoot Guidelines ......................................................... 46 3.4.2 Ringback Specification........................................................................... 46 3.4.3 Settling Limit Guideline .......................................................................... 46 Alphabetical Signals Reference .......................................................................... 71 Signal Summaries ............................................................................................... 78 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Datasheet Second Level (L2) Cache Implementation ........................................................... 7 AGTL+ Bus Topology in a Uniprocessor Configuration ......................................12 AGTL+ Bus Topology in a Dual-Processor Configuration ...................................12 Stop Clock State Machine ...................................................................................12 Processor VccCMOS Package Routing ..............................................................16 BSEL[1:0] Example for a 100/133 MHz or 100 MHz Only System Design .........21 BCLK, PICCLK, and TCK Generic Clock Waveform...........................................35 System Bus Valid Delay Timings ........................................................................35 System Bus Setup and Hold Timings..................................................................35 System Bus Reset and Configuration Timings....................................................36 Power-On Reset and Configuration Timings.......................................................36 Test Timings (TAP Connection) ..........................................................................37 Test Reset Timings .............................................................................................37 BCLK, PICCLK Generic Clock Waveform at the Processor Pins........................39 Low to High AGTL+ Receiver Ringback Tolerance.............................................40 Maximum Acceptable AGTL+ Overshoot/Undershoot Waveform .......................45 Non-AGTL+ Overshoot/Undershoot, Settling Limit, and Ringback 1 ..................45 Processor Functional Die Layout for CPUIDs up to and including 0683h ...........48 Package Dimensions...........................................................................................50 Top Side Processor Markings .............................................................................52 Intel(R) Pentium(R) III Processor Pinout..................................................................53 Conceptual Boxed Intel(R) Pentium(R) III Processor for the PGA370 Socket.........64 Space Requirements for the Boxed Processor to 850MHz.................................65 Space Requirements for the Boxed Processor from 866 to 933MHz..................65 Space Requirements for the Boxed Processor at 1 GHz ....................................66 Dimensions of Mechanical Step Feature in Heatsink Base.................................66 Dimensions of Notches in Heatsink Base ..........................................................67 Clip Keepout Requirements for the PGA370 (Top View) ....................................68 Thermal Airspace Requirement for all Boxed Intel(R) Pentium(R) III Processor Fan Heatsinks in the PGA370 Socket .................................................................69 Boxed Processor Fan Heatsink Power Cable Connector Description.................70 Motherboard Power Header Placement Relative to the Boxed Intel(R) Pentium(R) III Processor .............................................................................70 5 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz List of Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 6 Processor Identification......................................................................................... 9 Voltage Identification Definition .......................................................................... 18 System Bus Signal Groups ................................................................................ 20 Frequency Select Truth Table for BSEL[1:0] ...................................................... 21 Absolute Maximum Ratings ................................................................................ 22 Voltage and Current Specifications..................................................................... 24 AGTL+ Signal Groups DC Specifications ........................................................... 28 Non-AGTL+ Signal Group DC Specifications ..................................................... 28 Processor AGTL+ Bus Specifications ................................................................ 29 System Bus AC Specifications (Clock) ............................................................... 30 Valid System Bus to Core Frequency Ratios ..................................................... 31 System Bus AC Specifications (AGTL+ Signal Group) ....................................... 32 System Bus AC Specifications (CMOS Signal Group) ....................................... 32 System Bus AC Specifications (Reset Conditions) ............................................ 33 System Bus AC Specifications (APIC Clock and APIC I/O) ................................ 33 System Bus AC Specifications (TAP Connection) .............................................. 34 BCLK/PICCLK Signal Quality Specifications for Simulation at the Processor Pins .......................................................................................... 38 AGTL+ Signal Groups Ringback Tolerance Specifications at the Processor Pins .......................................................................................... 39 Example Platform Information............................................................................. 42 100 MHz AGTL+ Signal Group Overshoot/Undershoot Tolerance at Processor Pins ................................................................................................ 43 133 MHz AGTL+ Signal Group Overshoot/Undershoot Tolerance .................... 44 33 MHz CMOS Signal Group Overshoot/Undershoot Tolerance at Processor Pins ................................................................................................ 44 Signal Ringback Specifications for Non-AGTL+ Signal Simulation at the Processor Pins ......................................................................................... 46 Intel(R) Pentium(R) III Processor for the PGA370 Socket Thermal Design Power . 47 Thermal Diode Parameters ................................................................................. 49 Thermal Diode Interface...................................................................................... 49 Intel(R) Pentium(R) III Processor Package Dimensions .......................................... 51 Processor Die Loading Parameters .................................................................... 51 Signal Listing in Order by Signal Name .............................................................. 54 Signal Listing in Order by Pin Number ................................................................ 59 Boxed Processor Fan Heatsink Spatial Dimensions........................................... 66 Fan Heatsink Power and Signal Specifications................................................... 70 Signal Description ............................................................................................... 71 Output Signals..................................................................................................... 78 Input Signals ....................................................................................................... 79 Input/Output Signals (Single Driver).................................................................... 80 Input/Output Signals (Multiple Driver) ................................................................. 80 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 1.0 Introduction The Intel(R) Pentium(R) III processor for the PGA370 socket is the next member of the P6 family, in the Intel IA-32 processor line and hereafter will be referred to as the "Pentium III processor", or simply "the processor". The processor uses the same core and offers the same performance as the Intel(R) Pentium(R) III processor for the SC242 connector, but utilizes a new package technology called flip-chip pin grid array, or FC-PGA. This package utilizes the same 370-pin zero insertion force socket (PGA370) used by the Intel(R) CeleronTM processor. Thermal solutions are attached directly to the back of the processor core package without the use of a thermal plate or heat spreader. The Pentium III processor, like its predecessors in the P6 family of processors, implements a Dynamic Execution microarchitecture--a unique combination of multiple branch prediction, data flow analysis, and speculative execution. This enables these processors to deliver higher performance than the Intel Pentium processor, while maintaining binary compatibility with all previous Intel Architecture processors. The processor also executes Intel(R) MMXTM technology instructions for enhanced media and communication performance just as it's predecessor, the Intel Pentium III processor. Additionally, Pentium III processor executes Streaming SIMD (singleinstruction, multiple data) Extensions for enhanced floating point and 3-D application performance. The concept of processor identification, via CPUID, is extended in the processor family with the addition of a processor serial number. Refer to the Intel(R) Processor Serial Number application note for more detailed information. The processor utilizes multiple low-power states such as AutoHALT, Stop-Grant, Sleep, and Deep Sleep to conserve power during idle times. The processor includes an integrated on-die, 256 KB, 8-way set associative level-two (L2) cache. The L2 cache implements the new Advanced Transfer Cache Architecture with a 256-bit wide bus. The processor also includes a 16 KB level one (L1) instruction cache and 16 KB L1 data cache. These cache arrays run at the full speed of the processor core. As with the Intel Pentium III processor for the SC242 connector, the Pentium III processor for the PGA370 socket has a dedicated L2 cache bus, thus maintaining the dual independent bus architecture to deliver high bus bandwidth and performance (see Figure 1). Memory is cacheable for 64 GB of addressable memory space, allowing significant headroom for desktop systems. Refer to the Specification Update document for this processor to determine the cacheability and cache configuration options for a specific processor. The Specification Update document can be requested at your nearest Intel sales office. The processor utilizes the same multiprocessing system bus technology as the Pentium II processor. This allows for a higher level of performance for both uni-processor and two-way multiprocessor systems. The system bus uses a variant of GTL+ signaling technology called Assisted Gunning Transceiver Logic (AGTL+) signaling technology. Figure 1. Second Level (L2) Cache Implementation L2 Processor Core Tag L2 Intel (R) Pentium (R) III SECC2 Processor Datasheet Processor Core Intel (R) Pentium (R) III FC-PGA Processor 7 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 1.1 Terminology In this document, a `#' symbol after a signal name refers to an active low signal. This means that a signal is in the active state (based on the name of the signal) when driven to a low level. For example, when FLUSH# is low, a flush has been requested. When NMI is high, a nonmaskable interrupt has occurred. In the case of signals where the name does not imply an active state but describes part of a binary sequence (such as address or data), the `#' symbol implies that the signal is inverted. For example, D[3:0] = `HLHL' refers to a hex `A', and D[3:0]# = `LHLH' also refers to a hex `A' (H= High logic level, L= Low logic level). The term "system bus" refers to the interface between the processor, system core logic (a.k.a. the chipset components), and other bus agents. 1.1.1 Package and Processor Terminology The following terms are used often in this document and are explained here for clarification: * Pentium(R) III processor - The entire product including all internal components. * PGA370 socket - 370-pin Zero Insertion Force (ZIF) socket which a FC-PGA or PPGA packaged processor plugs into. * FC-PGA - Flip Chip Pin Grid Array. The package technology used on Pentium III processors for the PGA370 socket. * Advanced Transfer Cache (ATC) - New L2 cache architecture unique to the 0.18 micron Pentium III processors. ATC consists of microarchitectural improvements that provide a higher data bandwidth interface into the processor core that is completely scaleable with the processor core frequency. * Keep-out zone - The area on or near a FC-PGA packaged processor that system designs can not utilize. * Keep-in zone - The area of a FC-PGA packaged processor that thermal solutions may utilize. * OLGA - Organic Land Grid Array. The package technology for the core used in S.E.C.C. 2 processors that permits attachment of the heatsink directly to the die. * PPGA - Plastic Pin Grid Array. The package technology used for Intel (R) CeleronTM processors that utilize the PGA370 socket. * Processor - For this document, the term processor is the generic form of the Pentium III processor for the PGA370 socket in the FC-PGA package. * Processor core - The processor's execution engine. * S.E.C.C. - The processor package technology called "Single Edge Contact Cartridge". Used with Intel(R) Pentium(R) II processors. * S.E.C.C. 2 - The follow-on to S.E.C.C. processor package technology. This differs from its predecessor in that it has no extended thermal plate, thus reducing thermal resistance. Used with Intel(R) Pentium(R) III processors and latest versions of the Intel(R) Pentium(R) II processor. * SC242 - The 242-contact slot connector (previously referred to as slot 1 connector) that the S.E.C.C. and S.E.C.C. 2 plug into, just as the Intel(R) Pentium(R) Pro processor uses socket 8. The cache and L2 cache are an industry designated names. 8 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 1.1.2 Processor Naming Convention A letter(s) is added to certain processors (e.g., 600EB MHz) when the core freqnency alone may not uniquely identify the processor. Below is a summary of what each letter means as well as a table listing all the available Pentium III processors for the PGA370 socket. "B" -- 133 MHz System Bus Frequency "E" -- Processor with "Advanced Transfer Cache" (CPUID 068xh and greater) Table 1. Processor Identification Processor Core Frequency (MHz) System Bus Frequency (MHz) L2 Cache Size (Kbytes) L2 Cache Type2 CPUID1 500E 500 100 256 ATC 068xh 533EB 533 133 256 ATC 068xh 550E 550 100 256 ATC 068xh 600E 600 100 256 ATC 068xh 600EB 600 133 256 ATC 068xh 650 650 100 256 ATC 068xh 667 667 133 256 ATC 068xh 700 700 100 256 ATC 068xh 733 733 133 256 ATC 068xh 750 750 100 256 ATC 068xh 800 800 100 256 ATC 068xh 800EB 800 133 256 ATC 068xh 850 850 100 256 ATC 068xh 866 866 133 256 ATC 068xh 900 900 100 256 ATC 068xh 933 933 133 256 ATC 068xh 1B GHz 1000 133 256 ATC 068xh NOTES: 1. Refer to the Pentium(R) III Processor Specification Update for the exact CPUID for each processor. 2. ATC = Advanced Transfer Cache. ATC is an L2 Cache integrated on the same die as the processor core. With ATC, the interface between the processor core and L2 Cache is 256-bits wide, runs at the same frequency as the processor core and has enhanced buffering. Datasheet 9 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 1.2 Related Documents The reader of this specification should also be familiar with material and concepts presented in the following documents 1,2: AP-485, Intel(R) Document Intel Order Number Processor Identification and the CPUID Instruction 241618 (R) AP-585, Pentium II Processor GTL+ Guidelines 243330 AP-589, Design for EMI 243334 AP-905, Pentium(R) III Processor Thermal Design Guidelines 245087 AP-907, Pentium(R) III Processor Power Distribution Guidelines 245085 AP-909, Intel(R) Processor Serial Number 245125 Intel(R) Architecture Software Developer's Manual 243193 Volume I: Basic Architecture 243190 Volume II: Instruction Set Reference 243191 Volume III: System Programming Guide 243192 P6 Family of Processors Hardware Developer's Manual 244001 IA-32 Processors and Related Products 1999 Databook 243565 Pentium(R) 243502 II Processor Developer's Manual (R) Pentium III Processor Datasheet for SECC2 244452 Pentium(R) III Processor Datasheet for PGA370 245264 Pentium(R) III Processor Specification Update 244453 Intel(R) CeleronTM Processor Datasheet 243658 Intel(R) CeleronTM Processor Specificiation Update 243748 370-Pin Socket (PGA370) Design Guidelines 244410 PGA370 Heat Sink Cooling in MicroATX Chassis 245025 (R) 290675 (R) Intel 820 Chipset Platform Design Guide 290631 Intel(R) 840 Chipset Platform Design Guide 298021 Intel 810E Chipset Platform Design Guide CK98 Clock Synthesizer/Driver Design Guidelines Intel(R) 810E Chipset Clock Synthesizer/Driver Specification 245338 3 VRM 8.4 DC-DC Converter Design Guidelines 245335 Pentium III Processor for the PGA370 Socket I/O Buffer Models, XTK/XNS* Format 3 Pentium(R) Pro Processor BIOS Writer's Guide 3 Extensions to the Pentium(R) Pro Processor BIOS Writer's Guide 3 Pentium III Thermal/Mechanical Solution Functional Guidelines 245241 1. Unless otherwise noted, this reference material can be found on the Intel Developer's Website located at http://developer.intel.com. 2. For a complete listing of Intel(R) Pentium(R) III processor reference material, please refer to the Intel Developer's Website at http://developer.intel.com/design/PentiumIII/. 3. This material is available through an Intel field sales representative. 10 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.0 Electrical Specifications 2.1 Processor System Bus and VREF The Pentium III processor signals use a variation of the low voltage Gunning Transceiver Logic (GTL) signaling technology. The Intel(R) Pentium(R) Pro processor system bus specification is similar to the GTL specification, but was enhanced to provide larger noise margins and reduced ringing. The improvements are accomplished by increasing the termination voltage level and controlling the edge rates. This specification is different from the GTL specification, and is referred to as GTL+. For more information on GTL+ specifications, see the GTL+ buffer specification in the Intel(R) Pentium(R) II Processor Developer's Manual. Current P6 family processors vary from the Intel Pentium Pro processor in their output buffer implementation. The buffers that drive the system bus signals on the Intel(R) CeleronTM, Pentium II, and Pentium III processors are actively driven to VCCCORE for one clock cycle after the low to high transition to improve rise times. These signals should still be considered open-drain and require termination to a supply that provides the high signal level. Because this specification is different from the standard GTL+ specification, it is referred to as AGTL+, or Assisted GTL+ in this and other documentation. AGTL+ logic and GTL+ logic are compatible with each other and may both be used on the same system bus. For more information on AGTL+ routing, see the appropriate platform design guide. AGTL+ inputs use differential receivers which require a reference signal (VREF). VREF is used by the receivers to determine if a signal is a logical 0 or a logical 1, and is supplied by the motherboard to the PGA370 socket for the processor core. Local V REF copies should also be generated on the motherboard for all other devices on the AGTL+ system bus. Termination (usually a resistor at each end of the signal trace) is used to pull the bus up to the high voltage level and to control reflections on the transmission line. The processor contains on-die termination resistors that provide termination for one end of the AGTL+ bus, except for RESET#. These specifications assume another resistor at the end of each signal trace to ensure adequate signal quality for the AGTL+ signals and provide backwards compatibility for the Intel Celeron processor; see Table 9 for the bus termination voltage specifications for AGTL+. Refer to the Intel(R) Pentium(R) II Processor Developer's Manual for the AGTL+ bus specification. Solutions exist for single-ended termination as well, though this implementation changes system design and eliminate backwards compatibility for Intel Celeron processors in the PPGA package. Single-ended termination designs must still provide an AGTL+ termination resistor on the motherboard for the RESET# signal. Figure 2 is a schematic representation of the AGTL+ bus topology for the Pentium III processors in the PGA370 socket. Figure 3 is a schematic representation of the AGTL+ bus topoplogy in a dual-processor configuration with Pentium III processors in the PGA370 socket. The AGTL+ bus depends on incident wave switching. Therefore, timing calculations for AGTL+ signals are based on flight time as opposed to capacitive deratings. Analog signal simulation of the system bus including trace lengths is highly recommended when designing a system with a heavily loaded AGTL+ bus, especially for systems using a single set of termination resistors (i.e., those on the processor die). Such designs will not match the solution space allowed for by installation of termination resistors on the baseboard. Datasheet 11 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 2. AGTL+ Bus Topology in a Uniprocessor Configuration Processor Chipset Figure 3. AGTL+ Bus Topology in a Dual-Processor Configuration Processor 2.2 Chipset Processor Clock Control and Low Power States Processors allow the use of AutoHALT, Stop-Grant, Sleep, and Deep Sleep states to reduce power consumption by stopping the clock to internal sections of the processor, depending on each particular state. See Figure 4 for a visual representation of the processor low power states. Figure 4. Stop Clock State Machine HALT Instruction and HALT Bus Cycle Generated 2. Auto HALT P ower Down S tate BCLK running. Snoops and interrupts allowed. INIT#, BINIT#, INTR, SM I#, RESE T#, NMI 1. Norm al State Norm al execution. STPCLK# A sserted Snoop Event Occurs Snoop Event Serviced 4. HALT/Grant Snoop State BCLK running. Service snoops to caches. STPCLK# De-asserted and S top -G rant S ta te en te re d from A u to H A LT Snoop Event Occurs Snoop Event Serviced STPCLK# Asserted STPCLK# De-asserted 3. Stop Grant State BCLK running. Snoops and interrupts allowed. SLP# Asserted SLP# De-asserted 5. Sleep State BCLK running. No snoops or interrupts allowed. BCLK Input Stopped BCLK Input Restarted 6. Deep Sleep State BCLK stopped. No snoops or interrupts allowed. PCB757a 12 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz For the processor to fully realize the low current consumption of the Stop-Grant, Sleep and Deep Sleep states, a Model Specific Register (MSR) bit must be set. For the MSR at 02AH (Hex), bit 26 must be set to a `1' (this is the power on default setting) for the processor to stop all internal clocks during these modes. For more information, see the Intel Architecture Software Developer's Manual, Volume 3: System Programming Guide. 2.2.1 Normal State--State 1 This is the normal operating state for the processor. 2.2.2 AutoHALT Powerdown State--State 2 AutoHALT is a low power state entered when the processor executes the HALT instruction. The processor transitions to the Normal state upon the occurrence of SMI#, INIT#, or LINT[1:0] (NMI, INTR). RESET# causes the processor to immediately initialize itself. The return from a System Management Interrupt (SMI) handler can be to either Normal Mode or the AutoHALT Power Down state. See the Intel Architecture Software Developer's Manual, Volume III: System Programmer's Guide for more information. FLUSH# is serviced during the AutoHALT state, and the processor will return to the AutoHALT state. The system can generate a STPCLK# while the processor is in the AutoHALT Power Down state. When the system deasserts the STPCLK# interrupt, the processor returns execution to the HALT state. 2.2.3 Stop-Grant State--State 3 The Stop-Grant state on the processor is entered when the STPCLK# signal is asserted. Since the AGTL+ signal pins receive power from the system bus, these pins should not be driven (allowing the level to return to VTT) for minimum power drawn by the termination resistors in this state. In addition, all other input pins on the system bus should be driven to the inactive state. BINIT# and FLUSH# are not serviced during the Stop-Grant state. RESET# causes the processor to immediately initialize itself, but the processor stays in Stop-Grant state. A transition back to the Normal state occurs with the deassertion of the STPCLK# signal. A transition to the HALT/Grant Snoop state occurs when the processor detects a snoop on the system bus (see Section 2.2.4). A transition to the Sleep state (see Section 2.2.5) occurs with the assertion of the SLP# signal. While in Stop-Grant State, SMI#, INIT#, and LINT[1:0] are latched by the processor, and only serviced when the processor returns to the Normal state. Only one occurrence of each event is recognized and serviced upon return to the Normal state. Datasheet 13 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.2.4 HALT/Grant Snoop State--State 4 The processor responds to snoop transactions on the system bus while in Stop-Grant state or in AutoHALT Power Down state. During a snoop transaction, the processor enters the HALT/Grant Snoop state. The processor stays in this state until the snoop on the system bus has been serviced (whether by the processor or another agent on the system bus). After the snoop is serviced, the processor returns to the Stop-Grant state or AutoHALT Power Down state, as appropriate. 2.2.5 Sleep State--State 5 The Sleep state is a very low power state in which the processor maintains its context, maintains the phase-locked loop (PLL), and has stopped all internal clocks. The Sleep state can only be entered from the Stop-Grant state. Once in the Stop-Grant state, the SLP# pin can be asserted, causing the processor to enter the Sleep state. The SLP# pin is not recognized in the Normal or AutoHALT states. Snoop events that occur while in Sleep State or during a transition into or out of Sleep state will cause unpredictable behavior. In the Sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions or assertions of signals (with the exception of SLP# or RESET#) are allowed on the system bus while the processor is in Sleep state. Any transition on an input signal before the processor has returned to Stop-Grant state will result in unpredictable behavior. If RESET# is driven active while the processor is in the Sleep state, and held active as specified in the RESET# pin specification, then the processor will reset itself, ignoring the transition through Stop-Grant State. If RESET# is driven active while the processor is in the Sleep State, the SLP# and STPCLK# signals should be deasserted immediately after RESET# is asserted to ensure the processor correctly executes the reset sequence. While in the Sleep state, the processor is capable of entering its lowest power state, the Deep Sleep state, by stopping the BCLK input (see Section 2.2.6). Once in the Sleep or Deep Sleep states, the SLP# pin can be deasserted if another asynchronous system bus event occurs. The SLP# pin has a minimum assertion of one BCLK period. 2.2.6 Deep Sleep State--State 6 The Deep Sleep state is the lowest power state the processor can enter while maintaining context. The Deep Sleep state is entered by stopping the BCLK input (after the Sleep state was entered from the assertion of the SLP# pin). The processor is in Deep Sleep state immediately after BLCK is stopped. It is recommended that the BLCK input be held low during the Deep Sleep State. Stopping of the BCLK input lowers the overall current consumption to leakage levels. To re-enter the Sleep state, the BLCK input must be restarted. A period of 1 ms (to allow for PLL stabilization) must occur before the processor can be considered to be in the Sleep state. Once in the Sleep state, the SLP# pin can be deasserted to re-enter the Stop-Grant state. While in Deep Sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions or assertions of signals are allowed on the system bus while the processor is in Deep Sleep state. Any transition on an input signal before the processor has returned to Stop-Grant state will result in unpredictable behavior. 14 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.2.7 Clock Control BCLK provides the clock signal for the processor and on die L2 cache. During AutoHALT Power Down and Stop-Grant states, the processor will process a system bus snoop. The processor does not stop the clock to the L2 cache during AutoHALT Power Down or Stop-Grant states. Entrance into the Halt/Grant Snoop state allows the L2 cache to be snooped, similar to the Normal state. When the processor is in Sleep and Deep Sleep states, it does not respond to interrupts or snoop transactions. During the Sleep state, the internal clock to the L2 cache is not stopped. During the Deep Sleep state, the internal clock to the L2 cache is stopped. The internal clock to the L2 cache is restarted only after the internal clocking mechanism for the processor is stable (i.e., the processor has re-entered Sleep state). PICCLK should not be removed during the AutoHALT Power Down or Stop-Grant states. PICCLK can be removed during the Sleep or Deep Sleep states. When transitioning from the Deep Sleep state to the Sleep state, PICCLK must be restarted with BCLK. 2.3 Power and Ground Pins The operating voltage of the Pentium III processor for the PGA370 socket is the same for the core and the L2 cache; VCCCORE. There are four pins defined on the package for voltage identification (VID). These pins specify the voltage required by the processor core. These have been added to cleanly support voltage specification variations on current and future processors. For clean on-chip power and voltage reference distribution, the Pentium III processors in the FC-PGA package have 75 VCCCORE, 8 VREF, 15 VTT, and 77 VSS (ground) inputs. VCCCORE inputs supply the processor core, including the on-die L2 cache. VTT inputs (1.5V) are used to provide an AGTL+ termination voltage to the processor, and the VREF inputs are used as the AGTL+ reference voltage for the processor. Note that not all VTT inputs must be connected to the VTT supply. Refer to Section 5.3 for more details. On the motherboard, all VCCCORE pins must be connected to a voltage island (an island is a portion of a power plane that has been divided, or an entire plane). In addition, the motherboard must implement the VTT pins as a voltage island or large trace. Similarly, all GND pins must be connected to a system ground plane. Three additional power related pins exist on a processors utilizing the PGA370 socket. They are VCC1.5, VCC2.5 and VCCCMOS. The VCCCMOS pin provides the CMOS voltage for the pull-up resistors required on the system platform. A 2.5V source must be provided to the VCC2.5 pin and a 1.5V source must be provided to the VCC1.5 pin. The source for VCC1.5 must be the same as the one supplying VTT. The processor routes the compatible CMOS voltage source (1.5V or 2.5V) through the package and out to the VCCCMOS output pin. Processors based on 0.25 micron technology (e.g., the Intel Celeron processor) utilize 2.5V CMOS buffers. Processors based on 0.18 micron technology (e.g., the Pentium III processor for the PGA370 socket) utilize 1.5V CMOS buffers. The signal VCOREDET can be used by hardware on the motherboard to detect which CMOS voltage the processor requires. A VCOREDET connected to VSS within the processor indicates a 1.5V requirement on VCCCMOS. Refer to Figure 5. Each power signal must meet the specifications stated in Table 6 on page 24. Datasheet 15 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 5. Processor VCCCMOS Package Routing 2.5V 2.5V Supply V C C CMOS Intel (R) Pentium (R) III Processor 1.5V 1.5V Supply 0.1 uF CMOS Pullups CMOS Signals *ICH or Other Logic Note: *Ensure this logic is compatible with 1.5V signal levels of the Intel(R) Pentium (R) III processor for the PGA370 socket. 2.3.1 Phase Lock Loop (PLL) Power It is highly critical that phase lock loop power delivery to the processor meets Intel's requirements. A low pass filter is required for power delivery to pins PLL1 and PLL2. This serves as an isolated, decoupled power source for the internal PLL. Please refer to the Phase Lock Loop Power section in the appropriate platform design guide for the recommended filter specifications. 2.4 Decoupling Guidelines Due to the large number of transistors and high internal clock speeds, the processor is capable of generating large average current swings between low and full power states. The fluctuations can cause voltages on power planes to sag below their nominal values if bulk decoupling is not adequate. Care must be taken in the board design to ensure that the voltage provided to the processor remains within the specifications listed in Table 6. Failure to do so can result in timing violations (in the event of a voltage sag) or a reduced lifetime of the component (in the event of a voltage overshoot). Unlike SC242 based designs, motherboards utilizing the PGA370 socket must provide high frequency decoupling capacitors on all power planes for the processor. 2.4.1 Processor VCCCORE Decoupling The regulator for the VCCCORE input must be capable of delivering the dICCCORE/dt (defined in Table 6) while maintaining the required tolerances (also defined in Table 6). Failure to meet these specifications can result in timing violations (during VCCCORE sag) or a reduced lifetime of the component (during VCCCORE overshoot). 2.4.2 Processor System Bus AGTL+ Decoupling The processor requires both high frequency and bulk decoupling on the system motherboard for proper AGTL+ bus operation. See the AGTL+ buffer specification in the Intel(R) Pentium(R) II Processor Developer's Manual for more information. Also, refer to the appropriate platform design guide for recommended capacitor component placement. 16 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.5 Processor System Bus Clock and Processor Clocking The BCLK input directly controls the operating speed of the system bus interface. All AGTL+ system bus timing parameters are specified with respect to the rising edge of the BCLK input. See the P6 Family of Processors Hardware Developer's Manual for further details. 2.5.1 Mixing Processors of Differrent Frequencies In two-way MP (multi-processor) systems, mixing processors of different internal clock frequencies is not supported and has not been validated. Pentium III processors do not support a variable multiplier ratio; therefore, adjusting the ratio setting to a common clock frequency is not valid. However, mixing processors of the same frequency but of different steppings is supported. Details on support for mixed steppings is provided in the Pentium(R) III Processor Specification Update. Note: 2.6 Not all Pentium III processors for the PGA370 socket are validated for use in dual processor (DP) systems. Refer to the Pentium(R) III Processor Specification Update to determine which processors are DP capable. Voltage Identification There are four voltage identification pins on the PGA370 socket. These pins can be used to support automatic selection of VCCCORE voltages. These pins are not signals, but are either an open circuit or a short circuit to VSS on the processor. The combination of opens and shorts defines the voltage required by the processor core. The VID pins are needed to cleanly support voltage specification variations on current and future processors. VID[3:0] are defined in Table 2. A `1' in this table refers to an open pin and a `0' refers to a short to ground. The voltage regulator or VRM must supply the voltage that is requested or disable itself. To ensure a system is ready for current and future processors, the range of values in bold in Table 2 should be supported. A smaller range will risk the ability of the system to migrate to a higher performance processor and/or maintain compatibility with current processors. Datasheet 17 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 2. Voltage Identification Definition 1, 2 VID3 VID2 VID1 VID0 VccCORE 1 1 1 1 1.30 1 1 1 0 1.35 1 1 0 1 1.40 1 1 0 0 1.45 1 0 1 1 1.50 1 0 1 0 1.55 1 0 0 1 1.603 1 0 0 0 1.653 0 1 1 1 1.703 0 1 1 0 1.753 0 1 0 1 1.80 3 0 1 0 0 1.85 3 0 0 1 1 1.90 3 0 0 1 0 1.95 3 0 0 0 1 2.00 3 0 0 0 0 2.05 3 1 1 1 1 No Core NOTES: 1. 0 = Processor pin connected to VSS. 2. 1 = Open on processor; may be pulled up to TTL VIH on baseboard. 3. To ensure a system is ready for the Intel(R) Pentium(R) III and Intel(R) CeleronTM processors, the values in BOLD in Table 2 should be supported. Note that the `1111' (all opens) ID can be used to detect the absence of a processor core in a given socket as long as the power supply used does not affect these lines. Detection logic and pull-ups should not affect VID inputs at the power source (see Section 7.0). The VID pins should be pulled up to a TTL-compatible level with external resistors to the power source of the regulator only if required by the regulator or external logic monitoring the VID[3:0] signals. The power source chosen must be guaranteed to be stable whenever the supply to the voltage regulator is stable. This will prevent the possibility of the processor supply going above the specified VCCCORE in the event of a failure in the supply for the VID lines. In the case of a DC-toDC converter, this can be accomplished by using the input voltage to the converter for the VID line pull-ups. A resistor of greater than or equal to 10 k may be used to connect the VID signals to the converter input. Note that no changes have been made to the physical connector or pin definitions between the Intel-enabled VRM 8.2 and VRM 8.4 specifications. Intel requires that designs utilize VRM 8.4 specifications to meet the Pentium III processor requirements. 18 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.7 Processor System Bus Unused Pins All RESERVED pins must remain unconnected unless specifically noted. Connection of these pins to VCCCORE, VREF, VSS, VTT, or to any other signal (including each other) can result in component malfunction or incompatibility with future processors. See Section 5.3 for a pin listing of the processor and the location of each RESERVED pin. PICCLK must be driven with a valid clock input and the PICD[1:0] signals must be pulled-up to VCCCMOS even when the APIC will not be used. A separate pull-up resistor must be provided for each PICD signal. For reliable operation, always connect unused inputs or bidirectional signals to their deasserted signal level. The pull-up or pull-down resistor values are system dependent and should be chosen such that the logic high (VIH) and logic low (VIL) requirements are met. See Table 8 for DC specifications of non-AGTL+ signals. Unused AGTL+ inputs must be properly terminated to VTT on PGA370 socket motherboards which support the Intel Celeron and the Pentium III processors. For designs that intend to only support the Pentium III processor, unused AGTL+ inputs will be terminated by the processor's ondie termination resistors and thus do not need to be terminated on the motherboard. However, RESET# must always be terminated on the motherboard as the Pentium III processor for the PGA370 socket does not provide on-die termination of this AGTL+ input. For unused CMOS inputs, active low signals should be connected through a pull-up resistor to VCCCMOS and meet VIH requirements. Unused active high CMOS inputs should be connected through a pull-down resistor to ground (VSS) and meet VIL requirements. Unused CMOS outputs can be left unconnected. A resistor must be used when tying bidirectional signals to power or ground. When tying any signal to power or ground, a resistor will also allow for system testability. 2.8 Processor System Bus Signal Groups To simplify the following discussion, the processor system bus signals have been combined into groups by buffer type. All P6 family processor system bus outputs are open drain and require a high-level source provided termination resistors. However, the Pentium III processor for the PGA370 socket includes on-die termination. Motherboard designs that also support Intel Celeron processors in the PPGA package will need to provide AGTL+ termination on the system motherboard as well. Platform designs that support dual processor configurations will need to provide AGTL+ termination, via a termination package, in any socket not populated with a processor. AGTL+ input signals have differential input buffers which use VREF as a reference signal. AGTL+ output signals require termination to 1.5 V. In this document, the term "AGTL+ Input" refers to the AGTL+ input group as well as the AGTL+ I/O group when receiving. Similarly, "AGTL+ Output" refers to the AGTL+ output group as well as the AGTL+ I/O group when driving. The PWRGOOD, BCLK, and PICCLK inputs can each be driven from ground to 2.5 V. Other CMOS inputs (A20M#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SMI, SLP#, and STPCLK#) are only 1.5 V tolerant and must be pulled up to VCCCMOS. The CMOS, APIC, and TAP outputs are open drain and must be pulled high to VCCCMOS. This ensures correct operation for current Intel Pentium III and Intel Celeron processors. The groups and the signals contained within each group are shown in Table 3. Refer to Section 7.0 for a description of these signals. Datasheet 19 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 3. System Bus Signal Groups 1 Group Name Signals AGTL+ Input BPRI#, BR1#7, DEFER#, RESET# 6, RS[2:0]#, RSP#, TRDY# AGTL+ Output PRDY# AGTL+ I/O A[35:3]#, ADS#, AERR#, AP[1:0]#, BERR#, BINIT#, BNR#, BP[3:2]#, BPM[1:0]#, BR0#2, D[63:0]#, DBSY#, DEP[7:0]#, DRDY#, HIT#, HITM#, LOCK#, REQ[4:0]#, RP# CMOS Input3 A20M#, FLUSH#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SLP#, SMI#, STPCLK# CMOS Input4 PWRGOOD CMOS Output3 FERR#, IERR#, THERMTRIP# System Bus Clock4 BCLK APIC Clock4 PICCLK APIC I/O3 PICD[1:0] TAP Input3 TCK, TDI, TMS, TRST# TAP Output3 TDO Power/Other5 BSEL[1:0], CLKREF, CPUPRES#, EDGCTRL, PLL[2:1], RESET2#, SLEWCTRL, THERMDN, THERMDP, RTTCTRL8, VCOREDET, VID[3:0], VCC1.5, VCC2.5, VCCCMOS, VCCCORE, VREF, VSS, VTT, Reserved NOTES: 1. See Section 7.0 for information on the these signals. 2. The BR0# pin is the only BREQ# signal that is bidirectional. See Section 7.0 for more information. The internal BREQ# signals are mapped onto the BR[1:0]# pins after the agent ID is determined. 3. These signals are specified for VccCMOS (1.5 V for the Pentium III processor) operation. 4. These signals are 2.5 V tolerant. 5. VCCCORE is the power supply for the processor core and is described in Section 2.6. VID[3:0] is described in Section 2.6. VTT is used to terminate the system bus and generate VREF on the motherboard. VSS is system ground. VCC1.5, VCC2.5, VccCMOS are described in Section 2.3. BSEL[1:0] is described in Section 2.8.2 and Section 7.0. All other signals are described in Section 7.0. 6. RESET# must always be terminated to VTT on the motherboard, on-die termination is not provided for this signal. 7. This signal is not supported by all processors. Refer to the Pentium(R) III Processor Specification Update for a complete listing of processors that support this pin. 8. This signal is used to control the value of the processor on-die termination resistance. Refer to the platform design guide for the recommended pulldown resistor value. 2.8.1 Asynchronous vs. Synchronous for System Bus Signals All AGTL+ signals are synchronous to BCLK. All of the CMOS, Clock, APIC, and TAP signals can be applied asynchronously to BCLK. All APIC signals are synchronous to PICCLK. All TAP signals are synchronous to TCK. 20 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.8.2 System Bus Frequency Select Signals (BSEL[1:0]) These signals are used to select the system bus frequency. Table 2.9 defines the possible combinations of the signals and the frequency associated with each combination. The frequency is determined by the processor(s), chipset, and clock synthesizer. All system bus agents must operate at the same frequency. The Pentium III processor for the PGA370 socket operates at 100 MHz or 133 MHz system bus frequency; 66 MHz system bus operation is not supported. Individual processors will only operate at their specified front side bus (FSB) frequency, either 100 MHz or 133 MHz, not both. On motherboards that support operation at either 100 MHz or 133 MHz, the BSEL1 signal must be pulled up to a logic high by a resistor located on the motherboard and provided as a frequency selection signal to the clock driver/synthesizer. This signal can also be incorporated into RESET# logic on the motherboard if only 133 MHz operation is supported (thus forcing the RESET# signal to remain active as long as the BSEL1 signal is low. The BSEL0 signal will float from the processor and should be pulled up to a logic high by a resistor located on the motherboard. The BSEL0 signal can be incorporated into RESET# logic on the motherboard if 66 MHz operation is unsupported, as demonstrated in Figure 6. Refer to the appropriate clock synthesizer design guidelines and platform design guide for more details on the bus frequency select signals. In a 2-way MP system design, these BSEL[1:0] signals must connect the pins of both processors. Figure 6. BSEL[1:0] Example for a 100/133 MHz or 100 MHz Only System Design 3.3V 3.3V Processor 1 K 1 K BSEL0 BSEL1 10 K Note 1 Clock Driver 10 K Note 2 10 K Note 2 Chipset NOTES: 1. Some clock drivers may require a series resistor on their BSEL1 input. 2. Some chipsets may connect to the BSEL[1:0] signals and require a series resistor. See the appropriate platform design guide for implementation details. Table 4. Datasheet Frequency Select Truth Table for BSEL[1:0] BSEL1 BSEL0 Frequency 0 0 66 MHz (unsupported) 0 1 100 MHz 1 0 Reserved 1 1 133 MHz 21 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.9 Test Access Port (TAP) Connection Due to the voltage levels supported by other components in the Test Access Port (TAP) logic, it is recommended that the processor be the first in the TAP chain and followed by any other components within the system. A translation buffer should be used to connect the rest of the chain unless one of the other components is capable of accepting a 1.5V input. Similar considerations must be made for TCK, TMS, and TRST# signals. In a two-way MP system design, be cautious when including an empty PGA370 socket in the scan chain. All sockets in the scan chain must have a processor installed to complete the chain or the system must support a method to bypass the empty socket; PGA370 termination packages should not connect TDI to TDO in order to avoid placing the TDO pull-up resistor in parallel. 2.10 Maximum Ratings Table 5 contains processor stress ratings only. Functional operation at the absolute maximum and minimum is not implied nor guaranteed. The processor should not receive a clock while subjected to these conditions. Functional operating conditions are given in the AC and DC tables in Section 2.11 through Section 2.13. Extended exposure to the maximum ratings may affect device reliability. Furthermore, although the processor contains protective circuitry to resist damage from static electric discharge, one should always take precautions to avoid high static voltages or electric fields. Table 5. Absolute Maximum Ratings Symbol Parameter Min Max Unit Notes TSTORAGE Processor storage temperature -40 85 C VCCCORE and VTT Processor core voltage and termination supply voltage with respect to VSS -0.5 2.1 V VinAGTL AGTL+ buffer input voltage VTT - 2.18 2.18 V 1, 2 VinCMOS1.5 CMOS buffer DC input voltage with respect to VSS VTT - 2.18 2.18 V 1, 2, 3 VinCMOS2.5 CMOS buffer DC input voltage with respect to VSS -0.58 3.18 V 4 IVID Max VID pin current 5 mA ICPUPRES# Max CPUPRES# pin current 5 mA NOTES: 1. Input voltage can never exceed VSS + 2.18 volts. 2. Input voltage can never go below VTT - 2.18 volts. 3. Parameter applies to CMOS (except BCLK, PICCLK, and PWRGOOD), APIC, and TAP bus signal groups only. 4. Parameter applies to CMOS signals BCLK, PICCLK, and PWRGOOD only. 22 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.11 Processor DC Specifications The processor DC specifications in this section are defined at the PGA370 socket pins (bottom side of the motherboard). See Section 7.0 for the processor signal descriptions and Section 5.3 for the signal listings. Most of the signals on the processor system bus are in the AGTL+ signal group. These signals are specified to be terminated to 1.5V. The DC specifications for these signals are listed in Table 7 on page 28. To allow connection with other devices, the clock, CMOS, APIC, and TAP signals are designed to interface at non-AGTL+ levels. The DC specifications for these pins are listed in Table 8 on page 28. Table 6 through Table 9 list the DC specifications for the Pentium III processor for the PGA370 socket. Specifications are valid only while meeting specifications for junction temperature, clock frequency, and input voltages. Care should be taken to read all notes associated with each parameter. Datasheet 23 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 6. Voltage and Current Specifications 1, 2 (Sheet 1 of 3) Processor Symbol Parameter Core Freq 500E MHz 533EB MHz 550E MHz 600E MHz 600EB MHz 650 MHz VCCCORE Typ Max Unit Notes 0x681 1.60 3,4 0x683 1.60 3,4 0x686 n/a 0x681 1.65 3,4 0x683 1.65 3,4 0x686 n/a 0x681 1.60 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 VCC for Processor Core 3,4 V 667 MHz 700 MHz 733 MHz 750 MHz 800 MHz 800EB MHz 24 Min CPUID 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 6. Voltage and Current Specifications 1, 2 (Sheet 2 of 3) Processor Symbol Parameter Core Freq 850 MHz 866 MHz VCCCORE VCC for Processor Core 900 MHz 933 MHz 1B GHz Min Typ Max Unit Notes CPUID 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x681 1.65 3,4 0x683 1.65 3,4 0x686 1.70 0x686 1.70 3,4 0x683 1.65 3,4 0x686 1.70 3,4 0x683 1.70 3,4 0x686 1.70 3,4 0x686 1.76 3,4, 20 V 3,4 VTT, VCC1.5 Static AGTL+ bus termination voltage 1.455 1.50 1.545 V 1.5 3%, 5, 16 VTT, VCC1.5 Transient AGTL+ bus termination voltage 1.365 1.50 1.635 V 1.5 9% , 5 VREF AGTL+ input reference voltage -2% 2/3 VTT +2% V 2%, 7 VCLKREF CLKREF input reference voltage 1.169 1.25 1.331 V 6.5%, 15 Baseboard VCCCORE Tolerance, Static Processor core voltage static tolerance level at the PGA370 socket pins Baseboard VCCCORE Tolerance, Transient Processor core voltage transient tolerance level at the PGA370 socket pins ICCCORE ICC for processor core ICCCMOS ICC for VccCMOS Datasheet 500E MHz 533EB MHz 550E MHz 600E MHz 600EB MHz 650 MHz 667 MHz 700 MHz 733 MHz 750 MHz 800 MHz 800EB MHz 850 MHz 866 MHz 900 MHz 933 MHz 1B GHz 1B GHz -0.080 0.040 0.001 0.100 -0.130 0.080 -0.110 0.080 0.025 0.130 20, 21 10.0 10.6 11.0 12.0 12.0 13.0 13.3 14.0 14.6 15.0 16.0 16.0 16.2 16.3 17.0 17.7 19.4 20.8 A 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9 3, 8, 9, 20 250 mA V 6 20, 21 6 V 19 25 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 6. Voltage and Current Specifications 1, 2 (Sheet 3 of 3) Processor Symbol Parameter Core Freq Min Typ Max Unit Notes CPUID ICLKREF CLKREF voltage supply current 60 A IVTT Termination voltage supply current 2.7 A 10 ISGnt ICC Stop-Grant for processor core 2.5 A 8, 11 ISLP ICC Sleep for processor core 2.5 A 8 IDSLP ICC Deep Sleep for processor core 2.2 A dICCCORE/dt Power supply current slew rate 240 A/s 12, 13, 14 dIvTT/dt Termination current slew rate 8 A/s 12, 13, See Table 9 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. All specifications in this table apply only to the Pentium III processor. For motherboard compatibility with the Intel(R) CeleronTM processor, see the Intel(R) CeleronTM Processor Datasheet. 3. VccCORE and IccCORE supply the processor core and the on-die L2 cache. 4. Use the "typical voltage" specification with the "tolerance specifications" to provide correct voltage regulation to the processor. 5. VTT and Vcc1.5 must be held to 1.5V 9% while the AGTL+ bus is active. It is required that VTT and Vcc1.5 be held to 1.5V 3% while the processor system bus is static (idle condition). The 3% range is the required design target; 9% will come from the transient noise added. This is measured at the PGA370 socket pins on the bottom side of the baseboard. 6. These are the tolerance requirements, across a 20 MHz frequency bandwidth, measured at the processor socket pin on the soldered-side of the motherboard. VCCCORE must return to within the static voltage specification within 100 s after a transient event; see the VRM 8.4 DC-DC Converter Design Guidelines for further details. 7. VREF should be generated from VTT by a voltage divider of 1% resistors or 1% matched resistors. Refer to the Intel(R) Pentium(R) II Processor Developer's Manual for more details on VREF. 8. Maximum ICC is measured at VCC typical voltage and under a maximum signal loading conditions. 9. Voltage regulators may be designed with a minimum equivalent internal resistance to ensure that the output voltage, at maximum current output, is no greater than the nominal (i.e., typical) voltage level of VccCORE (VccCORE_TYP). In this case, the maximum current level for the regulator, IccCORE_REG, can be reduced from the specified maximum current IccCORE _MAX and is calculated by the equation: IccCORE_REG = IccCORE_MAX x (VccCORE_TYP - VccCORE_STATIC_TOLERANCE) / VccCORE_TYP 10.The current specified is the current required for a single processor. A similar amount of current is drawn through the termination resistors on the opposite end of the AGTL+ bus, unless single-ended termination is used (see Section 2.1). 11. The current specified is also for AutoHALT state. 12.Maximum values are specified by design/characterization at nominal VccCORE. 13.Based on simulation and averaged over the duration of any change in current. Use to compute the maximum inductance tolerable and reaction time of the voltage regulator. This parameter is not tested. 14.dIcc/dt specifications are measured and specified at the PGA370 socket pins. 15.CLKREF must be held to 1.25V 6.5%. This tolerance accounts for a 5% power supply and 1% resistor divider tolerance. It is recommended that the motherboard generate the CLKREF reference from either the 2.5V or 3.3V supply. VTT should not be used due to risk of AGTL+ switching noise coupling to this analog reference. 16.Static voltage regulation includes: DC output initial voltage set point adjust, Output ripple and noise, Output load ranges specified in the tables above. 17.FMB - Flexible Motherboard recommendation 18.These values are estimates based on preliminary simulation. 26 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 19.This specification applies to PGA370 processors operating at frequencies of 933MHz or higher. 20.This specification only applies to 1B GHz S-spec #: SL4WM. This part has a VID request of 1.70V, however the processor should be supplied 1.76V at the PGA Vcc pin by the Voltage Regulator Circuit or VRM. 21.This specification applies only to 1B GHz S-spec #: SL4WM. This value is 60mV offset from the standard specification and more at the Minimum specification. These tolerances are measured from a 1.70V base, while Vcc supplied is 1.76V. Datasheet 27 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 7. AGTL+ Signal Groups DC Specifications 1 Symbol VIL Parameter Min Max Unit Notes Input Low Voltage -0.150 VREF - 0.200 V 6 VREF + 0.200 VIH Input High Voltage VTT V 2, 3, 6 Ron Buffer On Resistance 16.67 5 IL Leakage Current for inputs, outputs, and I/O 100 A 4 NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies. 2. All inputs, outputs, and I/O pins must comply with the signal quality specifications in Section 3.0. 3. Minimum and maximum VTT are given in Table 9 on page 29. 4. (0 VIN 1.5 V +3%) and (0VOUT1.5V+3%). 5. Refer to the processor I/O Buffer Models for I/V characteristics. 6. Steady state input voltage must not be above VSS + 1.65V or below VTT - 1.65V. Table 8. Non-AGTL+ Signal Group DC Specifications 1 Symbol Parameter Min Max Unit Notes VIL1.5 Input Low Voltage -0.150 VREF - 0.200 V 9 VIL2.5 Input Low Voltage -0.58 0.700 V 5, 8 VIH1.5 Input High Voltage VREF + 0.200 VTT V 6, 9 VIH2.5 Input High Voltage 2.000 3.18 V 5, 8 VOL Output Low Voltage 0.400 V 2 V 7, 9, All outputs are open-drain VOH Output High Voltage VTT IOL Output Low Current ILI Input Leakage Current 100 A 3, 6 ILO Output Leakage Current 100 A 4, 7 9 mA NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentum III processors at all frequencies. 2. Parameter measured at 9 mA (for use with TTL inputs). 3. (0 VIN 2.5V +5%). 4. (0 VOUT 2.5V +5%). 5. For BCLK specifications, refer to Table 17 on page 38. 6. (0 VIN 1.5V +3%). 7. (0 VOUT 1.5V +3%). 8. Applies to non-AGTL+ signals BCLK, PICCLK, and PWRGOOD. 9. Applies to non-AGTL+ signals except BCLK, PICCLK, and PWRGOOD. 28 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 2.12 AGTL+ System Bus Specifications It is recommended that the AGTL+ bus be routed in a daisy-chain fashion with termination resistors to VTT. These termination resistors are placed electrically between the ends of the signal traces and the VTT voltage supply and generally are chosen to approximate the system platform impedance. The valid high and low levels are determined by the input buffers using a reference voltage called VREF. Refer to the appropriate platform design guide for more information Table 9 below lists the nominal specification for the AGTL+ termination voltage (VTT). The AGTL+ reference voltage (VREF) is generated on the system motherboard and should be set to 2/3 VTT for the processor and other AGTL+ logic. It is important that the baseboard impedance be specified and held to a 15% tolerance, and that the intrinsic trace capacitance for the AGTL+ signal group traces is known and well-controlled. For more details on the AGTL+ buffer specification, see the Intel(R) Pentium(R) II Processor Developer's Manual and AP-585, Intel(R) Pentium(R) II Processor AGTL+ Guidelines. Table 9. Processor AGTL+ Bus Specifications 1, 2 Symbol Parameter VTT Bus Termination Voltage On-die RTT Termination Resistor VREF Bus Reference Voltage Min Typ Max Units 130 4 1.05 V 5 1.50 40 0.950 2/3 VTT V Notes 3 NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies. 2. Pentium III processors for the PGA370 socket contain AGTL+ termination resistors on the processor die, except for the RESET# input. 3. VTT and Vcc1.5 must be held to 1.5V 9%. It is required that VTT and Vcc1.5 be held to 1.5V 3% while the processor system bus is idle (static condition). This is measured at the PGA370 socket pins on the bottom side of the baseboard. 4. The value of the on-die RTT is determined by the resistor value measured by the RTTCTRL signal pin. See Section 7.0 for more details on the RTTCTRL signal. Refer to the recommendation guidelines for the specific chipset/processor combination. 5. VREF is generated on the motherboard and should be 2/3 VTT 2% nominally. Insure that there is adequate VREF decoupling on the motherboard. 2.13 System Bus AC Specifications The processor system bus timings specified in this section are defined at the socket pins on the bottom of the motherboard. Unless otherwise specified, timings are tested at the processor pins during manufacturing. Timings at the processor pins are specified by design characterization. See Section 7.0 for the processor signal definitions. Table 10 through Table 16 list the AC specifications associated with the processor system bus. These specifications are broken into the following categories: Table 10 contains the system bus clock specifications, Table 12 contains the AGTL+ specifications, Table 13 contains the CMOS signal group specifications, Table 14 contains timings for the reset conditions, Table 15 and covers APIC bus timing, and Table 16 covers TAP timing. All processor system bus AC specifications for the AGTL+ signal group are relative to the rising edge of the BCLK input. All AGTL+ timings are referenced to VREF for both `0' and `1' logic levels unless otherwise specified. Datasheet 29 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz The timings specified in this section should be used in conjunction with the I/O buffer models provided by Intel. These I/O buffer models, which include package information, are available for the Pentium III processor in the FC-PGA package in Viewlogic* XTK/XNS* model format (formerly known as QUAD format) as the Pentium III Processor for the PGA370 Socket I/O Buffer Models, XTK/XNS Format (Electronic Format). AGTL+ layout guidelines are also available in the appropriate platform design guide. Care should be taken to read all notes associated with a particular timing parameter. 2.13.1 I/O Buffer Model An electronic copy of the I/O Buffer Model for the AGTL+ and CMOS signals is available at Intel's Developer's Website (http://developer.intel.com). The model is for use in single processor designs and assumes the presence of motherboard RTT values as described in Table 9 on page 29. Table 10. System Bus AC Specifications (Clock)1, 2, 3 T# Parameter Min T4: BCLK Low Time Unit Figure 10.0 ns 7.5 250 250 2.5 1.4 2.4 1.4 Notes 4 MHz 133.33 T2: BCLK Period Stability T3: BCLK High Time Max 100.00 System Bus Frequency T1: BCLK Period Nom 4 7 4, 5, 10 4, 5, 11 6, 7, 10 ps 6, 7, 11 ns 7 ns 7 9, 10 9, 11 9, 10 9, 11 T5: BCLK Rise Time 0.4 1.6 ns 7 8, 12 T6: BCLK Fall Time 0.4 1.6 ns 7 8, 12 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies. 2. All AC timings for the AGTL+ signals are referenced to the BCLK rising edge at 1.25V at the processor pin. All AGTL+ signal timings (address bus, data bus, etc.) are referenced at 1.00V at the processor pins. 3. N/A 4. The internal core clock frequency is derived from the processor system bus clock. The system bus clock to core clock ratio is determined during initialization. Individual processors will only operate at their specified system bus frequency, either 100 MHz or 133 MHz, not both. Table 11 shows the supported ratios for each processor. 5. The BCLK period allows a +0.5 ns tolerance for clock driver variation. See the appropriate clock synthesizer/ driver specification for details. 6. Due to the difficulty of accurately measuring clock jitter in a system, it is recommended that a clock driver be used that is designed to meet the period stability specification into a test load of 10 to 20 pF. This should be measured on the rising edges of adjacent BCLKs crossing 1.25V at the processor pin. The jitter present must be accounted for as a component of BCLK timing skew between devices. 7. The clock driver's closed loop jitter bandwidth must be set low to allow any PLL-based device to track the jitter created by the clock driver. The -20 dB attenuation point, as measured into a 10 to 20 pF load, should be less than 500 kHz. This specification may be ensured by design characterization and/or measured with a spectrum analyzer. See the appropriate clock synthesizer/driver specification for details 8. BCLK Rise time is measure between 0.5V-2.0V. BCLK fall time is measured between 2.0V-0.5V. 9. BCLK high time is measured as the period of time above 2.0V. BCLK low time is measured as the period of time below 0.5V 10.This specification applies to Pentium III processors operating at a system bus frequency of 100 MHz. 11. This specification applies to Pentium III processors operating at a system bus frequency of 133 MHz. 12.Not 100% tested. Specified by design characterization as a clock driver requirement. 30 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 11. Valid System Bus to Core Frequency Ratios 1, 2, 3 Processor Core Frequency (MHz) BCLK Frequency (MHz) Frequency Multiplier L2 Cache (MHz) 500E 500 100 5 500 533EB 533 133 4 533 550E 550 100 11/2 550 600E 600 100 6 600 600EB 600 133 9/2 600 650 650 100 13/2 650 667 667 133 5 667 700 700 100 7 700 733 733 133 11/2 733 750 750 100 15/2 750 800 800 100 8 800 800EB 800 133 6 800 850 850 100 17/2 850 866 866 133 13/2 866 900 900 100 9 900 933 933 133 7 933 1B GHz 1000 133 15/2 1000 NOTE: 1. Contact your local Intel representative for the latest information on processor frequencies and/or frequency multipliers. 2. While other bus ratios are defined, operation at frequencies other than those listed are not supported by the Pentium III processor. 3. Individual processors will only operate at their specified system bus frequency. Either 100 MHz or 133 MHz, not both. Datasheet 31 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 12. System Bus AC Specifications (AGTL+ Signal Group)1, 2, 3 T# Parameter Min Max Unit Figure T7: AGTL+ Output Valid Delay 0.40 3.25 T8: AGTL+ Input Setup Time 1.20 0.95 T9: AGTL+ Input Hold Time T10: RESET# Pulse Width Notes ns 8 4, 10, 11 ns 9 5, 6, 7, 10 ns 9 5, 6, 7, 11, 12 1.00 ns 9 8, 10 1.00 ms 10 6, 9, 10 NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies. 2. These specifications are tested during manufacturing. 3. All AC timings for the AGTL+ signals are referenced to the BCLK rising edge at 1.25V at the processor pin. All AGTL+ signal timings (compatibility signals, etc.) are referenced at 1.00V at the processor pins. 4. Valid delay timings for these signals are specified into 50 to 1.5V, VREF at 1.0 V 2% and with 56 on-die RTT. 5. A minimum of 3 clocks must be guaranteed between two active-to-inactive transitions of TRDY#. 6. RESET# can be asserted (active) asynchronously, but must be deasserted synchronously. For 2-way MP systems, RESET# should be synchrounous. 7. Specification is for a minimum 0.40 V swing from V REF - 200 mV to VREF + 200 mV. This assumes an edge rate of 0.3V/ns. 8. Specification is for a maximum 1.0 V swing from VTT - 1V to VTT. This assumes an edge rate of 3V/ns. 9. This should be measured after VCCCORE, VTT, VccCMOS , and BCLK become stable. 10.This specification applies to the Pentium III processor running at 100 MHz system bus frequency. 11. This specification applies to the Pentium III processor running at 133 MHz system bus frequency. 12.BREQ signals at 133 MHz system bus observe a 1.2 ns minimum setup time. Table 13. System Bus AC Specifications (CMOS Signal Group) 1, 2, 3, 4 T# Parameter Min Max Unit Figure T14: CMOS Input Pulse Width, except PWRGOOD 2 BCLKs 8 T15: PWRGOOD Inactive Pulse Width 10 BCLKs 8, 11 Notes Active and Inactive states 5 NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies 2. These specifications are tested during manufacturing. 3. These signals may be driven asynchronously. 4. All CMOS outputs shall be asserted for at least 2 BCLKs. 5. When driven inactive or after VCCCORE, VTT, VCCCMOS, and BCLK become stable. 32 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 14. System Bus AC Specifications (Reset Conditions) 1 T# Parameter Min T16: Reset Configuration Signals (A[14:5]#, BR0#, INIT#) Setup Time 4 T17: Reset Configuration Signals (A[14:5]#, BR0#, INIT#) Hold Time 2 Max 20 Unit Figure Notes BCLKs 10 Before deassertion of RESET# BCLKs 10 After clock that deasserts RESET# NOTES: 1. Unless otherwise noted, all specifications in this table apply to all Pentium III processor frequencies. Table 15. System Bus AC Specifications (APIC Clock and APIC I/O)1, 2, 3 T# Parameter Min Max Unit MHz Figure Notes T21: PICCLK Frequency 2.0 33.3 T22: PICCLK Period 30.0 500.0 ns 7 T23: PICCLK High Time 10.5 ns 7 @ > 1.7V T24: PICCLK Low Time 10.5 ns 7 @ < 0.7V T25: PICCLK Rise Time 0.25 3.0 ns 7 (0.7V - 1.7V) T26: PICCLK Fall Time 0.25 3.0 ns 7 (1.7V - 0.7V) T27: PICD[1:0] Setup Time 5.0 ns 9 4 T28: PICD[1:0] Hold Time 2.5 ns 9 4 T29a: PICD[1:0] Valid Delay (Rising Edge) 1.5 8.7 ns 7, 8 4, 5, 6 T29b: PICD[1:0] Valid Delay (Falling Edge) 1.5 12.0 ns 7, 8 4, 5, 6 NOTES: 1. Unless otherwise noted, all specifications in this table apply to Pentium III processors at all frequencies. 2. These specifications are tested during manufacturing. 3. All AC timings for the APIC I/O signals are referenced to the PICCLK rising edge at 1.25 V at the processor pins. All APIC I/O signal timings are referenced at 0.75 V at the processor pins. 4. Referenced to PICCLK rising edge. 5. For open drain signals, valid delay is synonymous with float delay. 6. Valid delay timings for these signals are specified into 150 load pulled up to 1.5 V. Datasheet 33 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 16. System Bus AC Specifications (TAP Connection)1, 2, 3 T# Parameter Min T30: TCK Frequency Max Unit 16.667 MHz Figure Notes T31: TCK Period 60.0 ns 7 T32: TCK High Time 25.0 ns 7 VREF + 0.200V, 10 T33: TCK Low Time 25.0 ns 7 VREF - 0.200V, 10 ns 7 (VREF - 0.200V) (VREF + 0.200V), T34: TCK Rise Time 5.0 4, 10 T35: TCK Fall Time 5.0 ns 7 (VREF + 0.200V) (VREF - 0.200V), 4, 10 T36: TRST# Pulse Width 40.0 ns 13 Asynchronous, 10 T37: TDI, TMS Setup Time 5.0 ns 12 5 T38: TDI, TMS Hold Time 14.0 ns 12 5 T39: TDO Valid Delay 1.0 10.0 ns 12 6, 7 25.0 ns 12 6, 7, 10 2.0 25.0 ns 12 6, 8, 9 25.0 ns 12 6, 8, 9, 10 T40: TDO Float Delay T41: All Non-Test Outputs Valid Delay T42: All Non-Test Inputs Setup Time T43: All Non-Test Inputs Setup Time 5.0 ns 12 5, 8, 9 T44: All Non-Test Inputs Hold Time 13.0 ns 12 5, 8, 9 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all Pentium III processors frequencies. 2. All AC timings for the TAP signals are referenced to the TCK rising edge at 0.75 V at the processor pins. All TAP signal timings (TMS, TDI, etc.) are referenced at 0.75 V at the processor pins. 3. These specifications are tested during manufacturing, unless otherwise noted. 4. 1 ns can be added to the maximum TCK rise and fall times for every 1 MHz below 16.667 MHz. 5. Referenced to TCK rising edge. 6. Referenced to TCK falling edge. 7. Valid delay timing for this signal is specified to 1.5 V. 8. Non-Test Outputs and Inputs are the normal output or input signals (besides TCK, TRST#, TDI, TDO, and TMS). These timings correspond to the response of these signals due to TAP operations. 9. During Debug Port operation, use the normal specified timings rather than the TAP signal timings. 10.Not 100% tested. Specified by design characterization. Note: For Figure 7 through Figure 13, the following apply: 1. Figure 7 through Figure 13 are to be used in conjunction with Table 10 through Table 16. 2. All AC timings for the AGTL+ signals at the processor pins are referenced to the BCLK rising edge at 1.25 V. All AGTL+ signal timings (address bus, data bus, etc.) are referenced at 1.00 V at the processor pins. 3. All AC timings for the APIC I/O signals at the processor pins are referenced to the PICCLK rising edge at 1.25 V. All APIC I/O signal timings are referenced at 0.75 V at the processor pins. 4. All AC timings for the TAP signals at the processor pins are referenced to the TCK rising edge at 0.75 V. All TAP signal timings (TMS, TDI, etc.) are referenced at 0.75 V at the processor pins. 34 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 7. BCLK, PICCLK, and TCK Generic Clock Waveform th tr V2 V3 CLK V1 tf tl tp Tr Tf Th Tl Tp V1 = = = = = = T5, T25, T34, (Rise Time) T6, T26, T35, (Fall Time) T3, T23, T32, (High Time) T4, T24, T33, (Low Time) T1, T22, T31 (BCLK, TCK, PICCLK Period) BCLK is referenced to 0.5V. TCK is referenced to V R E F - 200mV. PICCLK is referenced to 0.7V. V2 = BCLK is referenced to 2.0V. TCK is referenced to VREF - 200mV. PICCLK is referenced to 1.7V. V3 = BCLK and PICCLK are referenced to 1.25V. TCK is referenced to V REF. Figure 8. System Bus Valid Delay Timings CLK Tx Tx Signal Valid V Valid Tpw Tx = T7, T11, T29a, T29b (Valid Delay) Tpw = T14, T15 (Pulse Width) V = 1.0V for AGTL+ signal group; 0.75V for CMOS, APIC and TAP signal groups Figure 9. System Bus Setup and Hold Timings CLK Ts Signal V Th Valid Ts = T8, T12, T27 (Setup Time) Th = T9, T13, T28 (Hold Time) V = 1.0V for AGTL+ signal group; 0.75V for APIC and TAP signal groups Datasheet 35 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 10. System Bus Reset and Configuration Timings BCLK Tu Tt RESET# Tv Ty Configuration (A20M#, IGNNE#, LINT[1:0]) Tx Tz Safe Valid Tw Configuration (A[14:5]#, BR0#, FLUSH#, INT#) Valid Tt Tu Tv Tw Tx = = = = = T9 (AGTL+ Input Hold Time) T8 (AGTL+ Input Setup Time) T10 (RESET# Pulse Width) T16 (Reset Configuration Signals T17 (Reset Configuration Signals T20 (Reset Configuration Signals Ty = T19 (Reset Configuration Signals Tz = T18 (Reset Configuration Signals (A[14:5]#, BR0#, FLUSH#, INIT#) Setup Time) (A[14:5]#, BR0#, FLUSH#, INIT#) Hold Time) (A20M#, IGNNE#, LINT[1:0]) Hold Time) (A20M#, IGNNE#, LINT[1:0]) Delay Time) (A20M#, IGNNE#, LINT[1:0]) Setup Time) Figure 11. Power-On Reset and Configuration Timings BCLK V c c C O R E, V T T, V REF PWRGOOD V IL, max Ta V IH, min Tb RESET# TC Configuration (A20M#, IGNNE#, INTR, NMI) Valid Ratio Ta Tb Tc 36 = T15 (PWRGOOD Inactive Pulse) = T10 (RESET# Pulse Width) = T20 (Reset Configuration Signals (A20M#, IGNNE#, LINT[1:0]) Hold Time) Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 12. Test Timings (TAP Connection) TCK Tv Tw Tr Ts TDI, TMS Input Signal Tx Tu Ty Tz TDO Output Signal T r = T43 (All Non-Test Inputs Setup Time) T s = T44 (All Non-Test Inputs Hold Time) T u = T40 (TDO Float Delay) T v = T37 (TDI, TMS Setup Time) T w = T38 (TDI, TMS Hold TIme) T x = T39 (TDO Valid Delay) T y = T41 (All Non-Test Outputs Valid Delay) T z = T42 (All Non-Test Outputs Float Time) Figure 13. Test Reset Timings TRST# 1.25V Tq T q = T36 (TRST# Pulse Width) Datasheet 37 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 3.0 Signal Quality Specifications Signals driven on the processor system bus should meet signal quality specifications to ensure that the components read data properly and to ensure that incoming signals do not affect the long term reliability of the component. Specifications are provided for simulation at the processor pins. Meeting the specifications at the processor pins in Table 17, Table 18, and Table 23 ensures that signal quality effects will not adversely affect processor operation. 3.1 BCLK and PICCLK Signal Quality Specifications and Measurement Guidelines Table 17 describes the signal quality specifications at the processor pins for the processor system bus clock (BCLK) and APIC clock (PICCLK) signals. Figure 14 describes the signal quality waveform for the system bus clock at the processor pins. Table 17. BCLK/PICCLK Signal Quality Specifications for Simulation at the Processor Pins 1 T# Parameter Min Max Unit Figure V1: BCLK VIL 0.500 V 14 V1: PICCLK VIL 0.700 V 14 V 14 V2: BCLK VIH 2.000 V2 PICCLK VIH 2.000 V3: VIN Absolute Voltage Range -0.58 V4: BCLK Rising Edge Ringback V4: PICCLK Rising Edge Ringback Nom Notes V 14 V 14 2.000 V 14 2 2.000 V 14 2 3.18 V5: BCLK Falling Edge Ringback 0.500 V 14 2 V5: PICCLK Falling Edge Ringback 0.700 V 14 2 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all Pentium III processors frequencies. 2. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the BCLK/PICCLK signal can dip back to after passing the VIH (rising) or VIL (falling) voltage limits. This specification is an absolute value. 38 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 14. BCLK, PICCLK Generic Clock Waveform at the Processor Pins V3 V4 V2 V1 V5 V3 3.2 AGTL+ Signal Quality Specifications and Measurement Guidelines Many scenarios have been simulated to generate a set of AGTL+ layout guidelines which are available in the appropriate platform design guide. Refer to the Intel(R) Pentium(R) II Processor Developer's Manual (Order Number 243502) for the AGTL+ buffer specification. Table 18 provides the AGTL+ signal quality specifications for the processor for use in simulating signal quality at the processor pins. The Pentium III processor for the PGA370 socket maximum allowable overshoot and undershoot specifications for a given duration of time are detailed in Table 20 through Table 22. Figure 15 shows the AGTL+ ringback tolerance and Figure 16 shows the overshoot/undershoot waveform. Table 18. AGTL+ Signal Groups Ringback Tolerance Specifications at the Processor Pins 1, 2, 3 T# Parameter : Overshoot Min Unit Figure 100 mV 15 Notes 4, 8 : Minimum Time at High 0.50 ns 15 : Amplitude of Ringback 200 mV 15 5, 6, 7, 8 : Final Settling Voltage 200 mV 15 8 : Duration of Squarewave Ringback N/A ns 15 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all Pentium III processors frequencies. 2. Specifications are for the edge rate of 0.3 - 0.8V/ns. See Figure 15 for the generic waveform. 3. All values specified by design characterization. 4. Please see Table 20 for maximum allowable overshoot. 5. Ringback between VREF + 100 mV and VREF + 200 mV or VREF - 200 mV and VREF - 100 mVs requires the flight time measurements to be adjusted as described in the Intel AGTL+ Specifications (Intel(R)Pentium(R)II Developers Manual). Ringback below VREF + 100 mV or above VREF - 100 mV is not supported. 6. Intel recommends simulations not exceed a ringback value of VREF 200 mV to allow margin for other sources of system noise. 7. A negative value for indicates that the amplitude of ringback is above VREF. (i.e., = -100 mV specifies the signal cannot ringback below VREF + 100 mV). 8. and : are measured relative to VREF. : is measured relative to VREF + 200 mV. Datasheet 39 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 15. Low to High AGTL+ Receiver Ringback Tolerance V R E F + 0.2 V REF V R E F - 0.2 0.7V Clk Ref V start Clock Time Note: High to low case is analogous i b k t l 3.3 AGTL+ Signal Quality Specifications and Measurement Guidelines 3.3.1 Overshoot/Undershoot Guidelines Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below VSS. The overshoot guideline limits transitions beyond VCC or VSS due to the fast signal edge rates. The processor can be damaged by repeated overshoot events on 1.5 V or 2.5 V tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). Determining the impact of an overshoot/undershoot condition requires knowledge of the magnitude, the pulse direction and the activity factor (AF). Permanent damage to the processor is the likely result of excessive overshoot/undershoot. Violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. When performing simulations to determine impact of overshoot and overshoot, ESD diodes must be properly characterized. ESD protection diodes do not act as voltage clamps and will not provide overshoot or undershoot protection. ESD diodes modeled within Intel I/O Buffer models do not clamp undershoot or overshoot and will yield correct simulation results. If other I/O buffer models are being used to characterize the Pentium III processor performance, care must be taken to ensure that ESD models do not clamp extreme voltage levels. Intel I/O Buffer models also contain I/O capacitance characterization. Therefore, removing the ESD diodes from an I/O Buffer model will impact results and may yield excessive overshoot/undershoot. 40 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 3.3.2 Overshoot/Undershoot Magnitude Magnitude describes the maximum potential difference between a signal and its voltage reference level, VSS (overshoot) and VTT (undershoot). While overshoot can be measured relative to VSS using one probe (probe to signal and GND lead to VSS), undershoot must be measured relative to VTT. This could be acomplished by simultaneously measuring the VTT plane while measuring the signal undershoot. Today's oscilloscopes can easily calculate the true undershoot waveform. The true undershoot waveform can also be obtained with the following oscilloscope data file analysis: Converted Undershoot Waveform = VTT - Signal_measured Note: The converted undershoot waveform appears as a positive (overshoot) signal. Note: Overshoot (rising edge) and undershoot (falling edge) conditions are separate and their impact must be determined independently. After the true waveform conversion, the undershoot/overshoot specifications shown in Table 20 through Table 22 can be applied to the converted undershoot waveform using the same magnitude and pulse duration specifications used with an overshoot waveform. Overshoot/undershoot magnitude levels must observe the Absolute Maximum Specifications listed in Table 20 through Table 22. These specifications must not be violated at any time regardless of bus activity or system state. Within these specifications are threshold levels that define different allowed pulse durations. Provided that the magnitude of the overshoot/undershoot is within the Absolute Maximum Specifications (2.18V), the pulse magnitude, duration and activity factor must all be used to determine if the overshoot/undershoot pulse is within specifications. 3.3.3 Overshoot/Undershoot Pulse Duration Pulse duration describes the total time an overshoot/undershoot event exceeds the overshoot/ undershoot reference voltage (Vos_ref = 1.635V). The total time could encompass several oscillations above the reference voltage. Multiple overshoot/undershoot pulses within a single overshoot/undershoot event may need to be measured to determine the total pulse duration. Note: Oscillations below the reference voltage can not be substracted from the total overshoot/ undershoot pulse duration. Note: Multiple Overshoot/Undershoot events occurring within the same clock cycle must be considered together as one event. Using the worst case Overshoot/Undershoot Magnitude, sum together the individual Pulse Duraitons to determine the total Overshoot/Undershoot Pulse Duration for that total event. 3.3.4 Activity Factor Activity Factor (AF) describes the frequency of overshoot (or undershoot) occurrence relative to a clock. Since the highest frequency of assertion of an AGTL+ or a CMOS signal is every other clock, an AF = 1 indicates that the specific overshoot (or undershoot) waveform occurs EVERY OTHER clock cycle. Thus, an AF = 0.01 indicates that the specific overshoot (or undershoot) waveform occurs one time in every 200 clock cycles. The specifications provided in Table 20 through Table 22 show the Maximum Pulse Duration allowed for a given Overshoot/Undershoot Magnitude at a specific Activity Factor. Each Table entry is independent of all others, meaning that the Pulse Duration reflects the existence of overshoot/undershoot events of that magnitude ONLY. A platform with an overshoot/undershoot Datasheet 41 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz that just meets the pulse duration for a specific magnitude where the AF < 1, means that there can be NO other overshoot/undershoot events, even of lesser magnitude (note that if AF = 1, then the event occurs at all times and no other events can occur). 3.3.5 Note: Activity factor for AGTL+ signals is referenced to BCLK frequency. Note: Activity factor for CMOS signals is referenced to PICCLK frequency. Reading Overshoot/Undershoot Specification Tables The overshoot/undershoot specification for the Pentium III processor for the PGA370 socket is not a simple single value. Instead, many factors are needed to determine what the over/undershoot specification is. In addition to the magnitude of the overshoot, the following parameters must also be known: the junction temperature the processor will be operating at, the width of the overshoot (as measured above 1.635V) and the Activity Factor (AF). To determine the allowed overshoot for a particular overshoot event, the following must be done: 1. Determine the signal group that particular signal falls into. If the signal is an AGTL+ signal operating with a 100 MHz system bus, use Table 20 (100MHz AGTL+ signal group). If the signal is an AGTL+ signal operating with a 133MHz system bus, use Table 21 (133 MHz AGTL+ signal group). If the signal is a CMOS signal, use Table 22 (33 MHz CMOS signal group). 2. Determine the maximum junction temperature (Tj) for the range of processors that the system will support (80oC or 85oC). 3. Determine the Magnitude of the overshoot (relative to VSS) 4. Determine the Activity Factor (how often does this overshoot occur?) 5. From the appropriate Specification table, read off the Maximum Pulse Duration (in ns) allowed. 6. Compare the specified Maximum Pulse Duration to the signal being measured. If the Pulse Duration measured is less than the Pulse Duration shown in the table, then the signal meets the specifications. The above procedure is similar for undershoots after the undershoot waveform has been converted to look like an overshoot. Undershoot events must be analyzed separately from Overshoot events as they are mutually exclusive. Below is an example showing how the maximum pulse duration is determined for a given waveform. Table 19. Example Platform Information Required Information FSB Signal Group Maximum Platform Support 133 MHz AGTL+ Max Tj 85 C Overshoot Magnitude 2.13V Activity Factor (AF) Notes 0.1 Measured Value Measured overshoot occurs on average every 20 clocks NOTES: 1. Corresponding Maximum Puse Duration Specification - 2.4 ns 2. Pulse Duration (measured) - 2.0 ns Given the above parameters, and using Table 21 (85 oC/AF = 0.1 column) the maximum allowed pulse duration is 2.4 ns. Since the measure pulse duration is 2.0 ns, this particular overshoot event passes the overshoot specifications, although this doesn't guarantee that the combined overshoot/ undershoot events meet the specifications. 42 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 3.3.6 Determining if a System meets the Overshoot/Undershoot Specifications The overshoot/undershoot specifications listed in the following tables specify the allowable overshoot/undershoot for a single overshoot/undershoot event. However most systems will have multiple overshoot and/or undershoot events that each have their own set of parameters (duration, AF and magnitude). While each overshoot on its own may meet the overshoot specification, when you add the total impact of all overshoot events, the system may fail. A guideline to ensure a system passes the overshoot and undershoot specifications is shown below. It is important to meet these guidelines; otherwise, contact your Intrel field representative. 1. Insure no signal (CMOS or AGTL+) ever exceed the 1.635V OR 2. If only one overshoot/undershoot event magnitude occurs, ensure it meets the over/undershoot specifications in the following tables OR 3. If multiple overshoots and/or multiple undershoots occur, measure the worst case pulse duration for each magnitude and compare the results against the AF = 1 specifications. If all of these worst case overshoot or undershoot events meet the specifications (measured time < specifications) in the table (where AF=1), then the system passes. The following notes apply to Table 20 through Table 22. NOTES: 1. Overshoot/Undershoot Magnitude = 2.18V is an Absolute value and should never be exceeded 2. Overshoot is measured relative to VSS. 3. Undershoot is measured relative to VTT 4. Overshoot/Undershoot Pulse Duration is measured relative to 1.635V. 5. Rinbacks below VTT can not be subtracted from Overshoots/Undershoots 6. Lesser Undershoot does not allocate longer or larger Overshoot 7. OEM's are encouraged to follow Intel provided layout guidelines. Consult the layout guidelines provided in the specific platform design guide. 8. All values specified by design characterization Table 20. 100 MHz AGTL+ Signal Group Overshoot/Undershoot Tolerance at Processor Pins1,2 Maximum Pulse Duration at Tj = 80 C (ns) Maximum Pulse Duration at Tj = 85 C (ns) AF = 0.01 AF = 0.1 AF = 1 AF = 0.01 AF = 0.1 AF = 1 2.18 V 20 2.53 0.25 18.6 1.86 0.18 2.13 V 20 4.93 0.49 20 3.2 0.32 2.08 V 20 9.1 0.91 20 6.1 0.6 2.03 V 20 16.6 1.67 20 11.4 1.1 1.98 V 20 20 3.0 20 20 2 Overshoot/ Undershoot Magnitude 1.93 V 20 20 5.5 20 20 6.6 1.88 V 20 20 10 20 20 20 1. BCLK period is 10 ns. 2. Measurements taken at the processor socket pins on the solder-side of the motherboard. Datasheet 43 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 21. 133 MHz AGTL+ Signal Group Overshoot/Undershoot Tolerance 1, 2 Maximum Pulse Duration at Tj = 80 C (ns) Maximum Pulse Duration at Tj = 85 C (ns) AF = 0.01 AF = 0.1 AF = 1 AF = 0.01 AF = 0.1 AF = 1 2.18 V 15 1.9 0.19 14 1.4 0.14 2.13 V 15 3.7 0.37 15 2.4 0.24 2.08 V 15 6.8 0.68 15 4.6 0.46 2.03 V 15 12.5 1.25 15 8.6 0.84 1.98 V 15 15 2.28 15 15 1.5 1.93 V 15 15 4.1 15 15 5 1.88 V 15 15 7.5 15 15 15 Overshoot/Undershoot Magnitude 1. BCLK period is 7.5 ns. 2. Measurements taken at the processor socket pins on the solder-side of the motherboard. Table 22. 33 MHz CMOS Signal Group Overshoot/Undershoot Tolerance at Processor Pins1, 2 Maximum Pulse Duration at Tj = 80 C (ns) Maximum Pulse Duration at Tj = 85 C (ns) AF = 0.01 AF = 0.1 AF = 1 AF = 0.01 AF = 0.1 AF = 1 2.18 V 60 7.6 0.76 56 5.6 0.56 2.13 V 60 14.8 1.48 60 9.6 0.96 2.08 V 60 27.2 2.7 60 18.4 1.8 2.03 V 60 50 5 60 33 3.3 1.98 V 60 60 9.1 60 60 6 1.93 V 60 60 16.4 60 60 20 1.88 V 60 60 30 60 60 60 Overshoot/ Undershoot Magnitude NOTES: 1. PICCLK period is 30 ns. 2. Measurements taken at the processor socket pins on the solder-side of the motherboard. 44 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 16. Maximum Acceptable AGTL+ Overshoot/Undershoot Waveform Time Dependent Overshoot 2.18V 2.08V 1.98V 1.88V 1.635V VTT Converted Undershoot Waveform Max Overshoot Magnitude Undershoot Magnitude Vss 3.4 Overshoot = Magnitude Signal - Vss Undershoot Magnitude = V T T - Signal Time Dependent Undershoot Non-AGTL+ Signal Quality Specifications and Measurement Guidelines There are three signal quality parameters defined for non-AGTL+ signals: overshoot/undershoot, ringback, and settling limit. All three signal quality parameters are shown in Figure 17 for the nonAGTL+ signal group. Figure 17. Non-AGTL+ Overshoot/Undershoot, Settling Limit, and Ringback 1 Settling Limit Overshoot V HI Rising-Edge Ringback Falling-Edge Ringback Settling Limit VLO VSS Time Undershoot NOTES: 1. VHI = 1.5V for all non-AGTL+ signals except for BCLK, PICCLK, and PWRGOOD. VHI = 2.5 V for BCLK, PICCLK, and PWRGOOD. BCLK and PICCLK signal quality is detailed in Section 3.1. Datasheet 45 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 3.4.1 Overshoot/Undershoot Guidelines Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below VSS. The overshoot guideline limits transitions beyond VCC or VSS due to the fast signal edge rates (see Figure 17 for non-AGTL+ signals). The processor can be damaged by repeated overshoot events on 1.5 V or 2.5 V tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). Permanent damage to the processor is the likely result of excessive overshoot/undershoot. Violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. The overshoot/undershoot guideline is 0.3 V and assumes the absence of diodes on the input. These guidelines should be verified in simulations without the onchip ESD protection diodes present because the diodes will begin clamping the 1.5 V and 2.5 V tolerant signals beginning at approximately 0.7 V above the appropriate supply and 0.7 V below VSS. If signals are not reaching the clamping voltage, this will not be an issue. A system should not rely on the diodes for overshoot/undershoot protection as this will negatively affect the life of the components and make meeting the ringback specification very difficult. Note: 3.4.2 The undershoot guideline limits transitions exactly as described for the ATGL+ signals. See Figure 16. Ringback Specification Ringback refers to the amount of reflection seen after a signal has switched. The ringback specification is the voltage that the signal rings back to after achieving its maximum absolute value. See Figure 17 for an illustration of ringback. Excessive ringback can cause false signal detection or extend the propagation delay. The ringback specification applies to the input pin of each receiving agent. Violations of the signal ringback specification are not allowed under any circumstances for non-AGTL+ signals. Ringback can be simulated with or without the input protection diodes that can be added to the input buffer model. However, signals that reach the clamping voltage should be evaluated further. See Table 23 for the signal ringback specifications for non-AGTL+ signals for simulations at the processor pins. Table 23. Signal Ringback Specifications for Non-AGTL+ Signal Simulation at the Processor Pins 1 Input Signal Group Non-AGTL+ Signals 2 Non-AGTL+ Signals 2 PWRGOOD Transition Maximum Ringback (with Input Diodes Present) Unit Figure 01 Vref + 0.200 V 17 10 Vref - 0.200 V 17 01 2.00 V 17 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all Pentium III processor frequencies. 2. Non-AGTL+ signals except PWRGOOD. 3.4.3 Settling Limit Guideline Settling limit defines the maximum amount of ringing at the receiving pin that a signal must reach before its next transition. The amount allowed is 10% of the total signal swing (VHI -VLO) above and below its final value. A signal should be within the settling limits of its final value, when either in its high state or low state, before it transitions again. Signals that are not within their settling limit before transitioning are at risk of unwanted oscillations which could jeopardize signal integrity. Simulations to verify settling limit may be done either with or without the input protection diodes present. Violation of the settling limit guideline is acceptable if simulations of 5 to 10 successive transitions do not show the amplitude of the ringing increasing in the subsequent transitions. 46 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 4.0 Thermal Specifications and Design Considerations This chapter provides needed data for designing a thermal solution. However, for the correct thermal measuring processes, refer to AP-905, Intel(R) Pentium(R) III Processor Thermal Design Guidelines (Order Number 245087). The Pentium III processor uses flip chip pin grid array packaging technology and has a junction temperature (Tjunction) specified. 4.1 Thermal Specifications Table 24 provides the thermal design power dissipation and maximum temperatures for the Pentium III processor for the PGA370 socket. Systems should design for the highest possible processor power, even if a processor with a lower thermal dissipation is planned. A thermal solution should be designed to ensure the junction temperature never exceeds these specifications. Table 24. Intel(R) Pentium(R) III Processor for the PGA370 Socket Thermal Design Power Processor Processor Core Frequency (MHz) L2 Cache Size (Kbytes) Processor Thermal Design Power 2,3 (W) Power Density5 (W/cm2) CPUID up to 0683h Power Density5 (W/cm2) for CPUID 0686h Maximum TJUNCTION (C) 1 TJUNCTION Offset 4,6 (C) 500E 500 256 13.2 18.2 20.8 85 1.9 533EB 533 256 14.0 19.3 22.0 85 2.0 550E 550 256 14.5 20.0 22.8 85 2.1 600E 600 256 15.8 21.8 24.8 82 2.3 600EB 600 256 15.8 21.8 24.8 82 2.3 650 650 256 17.0 23.4 26.7 82 2.5 667 667 256 17.5 24.1 27.5 82 2.5 700 700 256 18.3 25.2 28.7 80 2.7 733 733 256 19.1 26.3 30.0 80 2.8 750 750 256 19.5 26.9 30.6 80 2.8 800 800 256 20.8 28.7 32.6 80 3.0 800EB 800 256 20.8 28.7 32.6 80 3.0 850 850 256 22.5 31.0 35.2 80 3.3 866 866 256 22.9 31.5 35.9 80 3.3 900 900 256 23.2 N/A 37.1 75 3.6 933 933 256 24.5 33.8 38.4 75 3.6 1B GHz 1000 256 26.1 36.0 40.9 70 3.8 1B GHz7,8 1000 256 29.6 N/A 43.9 70 3.8 NOTES: 1. These values are specified at nominal VCCCORE for the processor pins. 2. Thermal Design Power (TDP) represents the maximum amount of power the thermal solution is required to dissipate. The thermal solution should be designed to dissipate the TDP power without exceeding the maximum Tjunction specification. 3. TDP does not represent the power delivery and voltage regulation requirements for the processor. Refer to Table 6 for voltage regulation and electrical specifications. Datasheet 47 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 4. Tjunctionoffset is the worst-case difference between the thermal reading from the on-die thermal diode and the hottest location on the processor's core. 5. Power density is the maximum power the processor die can dissipate (i.e., processor power) divided by the die area over which the power is generated. Power for these processors is generated from the core area shown in Figure 18. 6. TJUNCTION offset values do not include any thermal diode kit measurement error. Diode kit measurement error must be added to the TJUNCTION offset value from the table, as outlined in the Intel(R) Pentium(R) III processor Thermal Metrology for CPUID-068h Family Processors (Order Number: 245301). Intel has characterized the use of the Analog Devices AD1021 diode measurement kit and found its measurement error to be 1 C. 7. These values are estimates based on preliminary simulation. 8. This specification only applies to 1B GHz S-spec #: SL4WM. This part has a VID request of 1.70V, however the processor should be supplied 1.76V at the PGA Vcc pin by the Voltage Regulator Circuit or VRM. Figure 18 is a block diagram of the Pentium III processor die layout. The layout differentiates the processor core from the cache die area. In effect, the thermal design power indentified in Table 24 is dissipated entirely from the processor core area. Thermal solution designs should compensate for this smaller heat flux area and not assume that the power is uniformly distributed across the entire die area. The drawing below does not depict the 5% die shrink (CPUID=0686h) values as follows: Die Area (0.900), Core Area (0.642), Cache Area (0.258) cm 2. Figure 18. Processor Functional Die Layout for CPUIDs up to and including 0683h Die Area (1.046 cm2) Core Area (0.726 cm2) Cache Area (0.320 cm2) 4.1.1 Thermal Diode The Pentium III processor for the PGA370 socket incorporates an on-die diode that may be used to monitor the die temperature (junction temperature). A thermal sensor located on the motherboard, or a stand-alone measurement kit, may monitor the die temperature of the processor for thermal management or instrumentation purposes. Table 25 and Table 26 provide the diode parameter and interface specifications. Note: 48 The reading of the thermal sensor connected to the thermal diode will not necessarily reflect the temperature of the hottest location on the die. This is due to inaccuracies in the thermal sensor, ondie temperature gradients between the location of the thermal diode and the hottest location on the die at a given point in time, and time based variations in the die temperature measurement. Time based variations can occur when the sampling rate of the thermal diode (by the thermal sensor) is slower than the rate at which the Tjunction temperature can change. Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 25. Thermal Diode Parameters1 Symbol Parameter Min Typ Ifw Forward Bias Current 5 n Diode Ideality Factor 1.0057 1.0080 Max Unit 300 A 1.0125 Notes 1 2, 3, 4 NOTES: 1. Intel does not support or recommend operation of the thermal diode under reverse bias. 2. Characterized at 100 C with a forward bias current of 5 - 300 A. 3. The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode equation: Ifw=Is(e^ ((Vd*q)/(nkT)) - 1), where Is = saturation current, q = electronic charge, Vd = voltage across the diode, k = Boltzmann Constant, and T = absolute temperature (Kelvin). 4. Not 100% tested. Specified by design characterization. Table 26. Thermal Diode Interface Datasheet Pin Name PGA370 Socket pin # Pin Description THERMDP AL31 diode anode (p_junction) THERMDN AL29 diode cathode (n_junction) 49 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 5.0 Mechanical Specifications The Pentium III processor uses a FC-PGA package technology. Mechanical specifications for the processor are given in this section. See Section 1.1.1 for a complete terminology listing. The processor utilizes a PGA370 socket for installation into the motherboard. Details on the socket are available in the 370-Pin Socket (PGA370) Design Guidelines. Note: For Figure 19, the following apply: 1. Unless otherwise specified, the following drawings are dimensioned in inches. 2. All dimensions provided with tolerances are guaranteed to be met for all normal production product. 3. Figures and drawings labeled as "Reference Dimensions" are provided for informational purposes only. Reference dimensions are extracted from the mechanical design database and are nominal dimensions with no tolerance information applied. Reference dimensions are NOT checked as part of the processor manufacturing. Unless noted as such, dimensions in parentheses without tolerances are reference dimensions. 4. Drawings are not to scale. 5.1 FC-PGA Mechanical Specifications The following figure with package dimensions is provided to aid in the design of heatsink and clip solutions as well as demonstrate where pin-side capacitors will be located on the processor. Table 27 includes the measurements for these dimensions in both inches and millimeters. Figure 19. Package Dimensions 50 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 27. Intel(R) Pentium(R) III Processor Package Dimensions Millimeters Inches Symbol Minimum Maximum A1 0.787 A2 Notes Minimum Maximum 0.889 0.031d 0.035 1.000 1.200 0.039 0.047 B1 11.226 11.329 0.442 0.446 B2 9.296 9.398 0.366 0.370 C1 23.495 max 0.925 max C2 21.590 max 0.850 max D 49.428 49.632 1.946 1.954 D1 45.466 45.974 1.790 1.810 G1 0.000 17.780 0 0.700 G2 0.000 17.780 0 0.700 G3 0.000 0.889 0 0.035 H 2.540 Nominal L 3.048 3.302 P 0.431 0.483 Pin TP 0.100 Pin Diameter 0.508 Diameteric True Position (Pin-to-Pin) Notes Nominal 0.120 0.130 0.017 0.019 0.020 Diameteric True Position (Pin-to-Pin) NOTES: 1. Capacitors will be placed on the pin-side of the FC-PGA package in the area defined by G1, G2, and G3. This area is a keepout zone for motherboard designers. The bare processor die has mechanical load limits that should not be exceeded during heat sink assembly, mechanical stress testing, or standard drop and shipping conditions. The heatsink attach solution must not induce permanent stress into the processor substrate with the exception of a uniform load to maintain the heatsink to the processor thermal interface. The package dynamic and static loading parameters are listed in Table 28. For Table 28, the following apply: 1. It is not recommended to use any portion of the processor substrate as a mechanical reference or load bearing surface for thermal solutions. 2. Parameters assume uniformly applied loads Table 28. Processor Die Loading Parameters Parameter Dynamic (max)1 Static (max)2 Unit Silicon Die Surface 200 50 lbf Silicon Die Edge 100 12 lbf NOTES: 1. This specification applies to a uniform and a non-uniform load. 2. This is the maximum static force that can be applied by the heatsink and clip to maintain the heatsink and processor interface Datasheet 51 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 5.2 Processor Markings The following figure exemplifies the processor top-side markings and it is provided to aid in the identification of an Pentium III processor for the PGA370 socket. Table 27 lists the measurements for the package dimensions. Figure 20. Top Side Processor Markings Dynamic Production Mark Example Static Mark ink printed at substrate supplier Country of Origin pentium III logo intel (R) MALAY i (m) (c) '99 RB80526PY550266 FFFFFFFF-0001 SSSSS FPO # - S/N S-spec# Product Code Dynamic Laser Mark Swatch 5.3 Processor Signal Listing Table 29 and Table 30 provide the processor pin definitions. The signal locations on the PGA370 socket are to be used for signal routing, simulation, and component placement on the baseboard. Figure 21 provides a pin-side view of the Pentium III processor pin-out. The following notes apply to Table 29 and Table 30: NOTES: 1. These pins are required for backwards compatibility with other Intel processors. They are not used by the Pentium III processor. Refer to the appropriate platform design guide and Section 7.1 for implementation details. 2. RESET# signal must be connected to pins AH4 and X4 for backwards compatibility. Refer to the appropriate platform design guide and Section 7.1 for implementation details. If backwards compatibility is not required, then RESET2# (X4) should be connected to GND. 3. VCC1.5V must be supplied by the same voltage source supplying the VTT pins. 4. These VTT pins must be left unconnected (N/C) for backwards compatibility with Intel(R) CeleronTM processors (CPUID 066xh). For designs which do not support the Intel Celeron processors (CPUID 066xh), and for compatibility with future processors, these VTT pins should be connected to the VTT plane. Refer to the appropriate platform design guide and Section 7.1 for implementation details. For dual processor designs, these pins must be connected to VTT. 5. This pin is required for backwards compatibility. If backwards compatibility is not required, this pin may be left connected to VCCCORE. Refer to the appropriate platform design guide for implementation details. 6. Previously, PGA370 designs defined this pin as a GND. It is now reserved and must be left unconnected (N/C). 7. Previously, PGA370 socket designs defined this pin as a GND. It is now CLKREF. 8. For Uniprocessor designs, this pin is not used and it is defined as RESERVED. Refer to the Peniutm(R) III processor Specification Update for a complete listing of processors that support DP operation. 52 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 21. Intel(R) Pentium(R) III Processor Pinout 1 3 5 2 7 4 6 9 11 8 13 10 12 15 14 17 19 16 21 18 23 20 25 22 27 24 29 26 28 31 33 30 35 32 37 34 36 AN AN VSS A16 A12 A6 VTT VTT AP1 BPRI DEFER VTT RP TRDY DRDY BR0 ADS TRST TDI TDO AM AM RSV VCC VSS VCC VSS VCC VSS VSS VCC VCC VCC VSS VSS VCC VCC VSS VSS VID1 AL AL VSS VSS A15 A13 A9 VTT AP0 A7 REQ4 REQ3 VTT HITM HIT DBSY THRMDN THRMDP TCK VID0 VID2 AK AK VCC VSS A28 A3 A11 VREF6 A14 VTT REQ0 LOCK VREF7 AERR PWRGD RS2 RSV TMS VCC VSS AJ AJ A21 VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC BSEL1 BSEL0 SMI VID3 AH AH RESET VSS A10 A5 A8 A4 BNR REQ1 REQ2 VTT RS1 VCC RS0 THERM AG EDGCTRL A19 SLP VCC VSS AE INIT A17 A22 VCC VCC A20M AD VSS A31 STPCLK VSS A25 A35 VCC AG TRIP AF VCC VSS VCC VREF5 IGNNE AF VSS IERR FLUSH V_1.5 AC AC A33 A20 VSS AB VCC FERR VSS RSP AB A24 A23 VSS VCC V_CMOS AA AA A27 A30 VTT VCC VTT VCC Z Z VSS A29 A18 VCC Y RSV A26 X W BR1 D0 RESET2 A32 VSS D4 BERR D15 T VREF4 VCC Pin Side View VSS VCC D5 R Q P N L VCC D7 H G D11 RSV RSV VSS Q N L VCC VCC PICCLK VCC D19 K VSS PREQ PICD0 VSS VTT J H VCC BP2 VSS LINT1 RSV G F VCC D26 D C R M LINT0 PICD1 F E S P VSS RSV RSV D24 D16 RSV VCC VCC VCC D23 U VSS RSV D3 VREF2 VSS D21 VSS VSS D30 VTT RTT VTT CTRL VSS VCC RSV D9 D20 V VCC VTT VCC VCC VCC VSS D13 K J D18 D14 M VREF3 VSS VCC D2 W T VSS VTT D17 D10 BCLK VSS VCC RSV D12 X VSS RSV PLL2 D6 D1 VCC PLL1 S D8 Y VSS VCC VSS VCC A34 V_2.5 VSS CLKREF VSS V U AE AD VSS VCC D25 VSS D33 B VSS VCC D35 A D32 VCC VCC D31 VSS D29 D22 VSS D38 D34 VCC D28 RSV VCC D39 D36 D37 VCC VCC D42 D45 VCC VSS D43 D27 VSS D41 D49 D51 VREF1 VCC D52 D40 VCC VSS D44 D63 VSS VSS D59 D47 D48 VCC RSV VCC D55 VCC VSS VSS VSS VSS D54 VSS D57 VSS VTT VCC D58 VCC D46 VCC VSS D50 VSS VCC VCC DEP4 VSS DEP5 VSS VCC VREF0 VCC DEP1 VCC DEP7 D61 VSS VCC DEP6 D56 D60 D53 VSS SLEW CTRL D62 VSS DEP0 VSS DEP3 VSS BPM1 VCC E D VCC C BPM0 DEP2 BP3 CPUPRES B BINIT A PRDY VSS Dep7 1 3 2 Datasheet 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 21 20 23 22 25 24 27 26 29 28 31 30 33 32 35 34 37 36 53 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 29. Signal Listing in Order by Signal Name Pin No. AK8 54 Pin Name A3# Signal Group Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. AGTL+ I/O B36 Pin Name Signal Group BINIT# AGTL+ I/O AH12 A4# AGTL+ I/O AH14 BNR# AGTL+ I/O AH8 A5# AGTL+ I/O G33 BP2# AGTL+ I/O AN9 A6# AGTL+ I/O E37 BP3# AGTL+ I/O AL15 A7# AGTL+ I/O C35 BPM0# AGTL+ I/O AH10 A8# AGTL+ I/O E35 BPM1# AGTL+ I/O AL9 A9# AGTL+ I/O AN17 BPRI# AGTL+ Input AH6 A10# AGTL+ I/O AN29 BR0# AGTL+ I/O AK10 A11# AGTL+ I/O X2 BR1#8 AGTL+ Input AN5 A12# AGTL+ I/O AJ33 BSEL0 Power/Other AL7 A13# AGTL+ I/O AJ31 BSEL1 Power/Other 7 AK14 A14# AGTL+ I/O Y33 CLKREF AL5 A15# AGTL+ I/O C37 CPUPRES# Power/Other AN7 A16# AGTL+ I/O W1 D0# AGTL+ I/O AE1 A17# AGTL+ I/O T4 D1# AGTL+ I/O Z6 A18# AGTL+ I/O N1 D2# AGTL+ I/O AG3 A19# AGTL+ I/O M6 D3# AGTL+ I/O Power/Other AC3 A20# AGTL+ I/O U1 D4# AGTL+ I/O AE33 A20M# CMOS Input S3 D5# AGTL+ I/O AJ1 A21# AGTL+ I/O T6 D6# AGTL+ I/O AE3 A22# AGTL+ I/O J1 D7# AGTL+ I/O AB6 A23# AGTL+ I/O S1 D8# AGTL+ I/O AB4 A24# AGTL+ I/O P6 D9# AGTL+ I/O AF6 A25# AGTL+ I/O Q3 D10# AGTL+ I/O Y3 A26# AGTL+ I/O M4 D11# AGTL+ I/O AA1 A27# AGTL+ I/O Q1 D12# AGTL+ I/O AK6 A28# AGTL+ I/O L1 D13# AGTL+ I/O Z4 A29# AGTL+ I/O N3 D14# AGTL+ I/O AA3 A30# AGTL+ I/O U3 D15# AGTL+ I/O AD4 A31# AGTL+ I/O H4 D16# AGTL+ I/O X6 A32# AGTL+ I/O R4 D17# AGTL+ I/O AC1 A33# AGTL+ I/O P4 D18# AGTL+ I/O W3 A34# AGTL+ I/O H6 D19# AGTL+ I/O AF4 A35# AGTL+ I/O L3 D20# AGTL+ I/O AN31 ADS# AGTL+ I/O G1 D21# AGTL+ I/O AK24 AERR# AGTL+ I/O F8 D22# AGTL+ I/O AL11 AP0# AGTL+ I/O G3 D23# AGTL+ I/O AN13 AP1# AGTL+ I/O K6 D24# AGTL+ I/O W37 BCLK System Bus Clock E3 D25# AGTL+ I/O V4 BERR# AGTL+ I/O E1 D26# AGTL+ I/O Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. Datasheet Pin Name Signal Group Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. Pin Name Signal Group F12 D27# AGTL+ I/O C31 DEP1# AGTL+ I/O A5 D28# AGTL+ I/O A33 DEP2# AGTL+ I/O A3 D29# AGTL+ I/O A31 DEP3# AGTL+ I/O J3 D30# AGTL+ I/O E31 DEP4# AGTL+ I/O C5 D31# AGTL+ I/O C29 DEP5# AGTL+ I/O F6 D32# AGTL+ I/O E29 DEP6# AGTL+ I/O C1 D33# AGTL+ I/O A29 DEP7# AGTL+ I/O C7 D34# AGTL+ I/O AN27 DRDY# AGTL+ I/O B2 D35# AGTL+ I/O AG1 EDGCTRL 5 Power/Other C9 D36# AGTL+ I/O AC35 FERR# CMOS Output A9 D37# AGTL+ I/O AE37 FLUSH# CMOS Input D8 D38# AGTL+ I/O AM22 GND Power/Other D10 D39# AGTL+ I/O AM26 GND Power/Other C15 D40# AGTL+ I/O AM30 GND Power/Other D14 D41# AGTL+ I/O AM34 GND Power/Other D12 D42# AGTL+ I/O AM6 GND Power/Other A7 D43# AGTL+ I/O AN3 GND Power/Other A11 D44# AGTL+ I/O B12 GND Power/Other C11 D45# AGTL+ I/O B16 GND Power/Other A21 D46# AGTL+ I/O B20 GND Power/Other A15 D47# AGTL+ I/O B24 GND Power/Other A17 D48# AGTL+ I/O B28 GND Power/Other C13 D49# AGTL+ I/O B32 GND Power/Other C25 D50# AGTL+ I/O B4 GND Power/Other A13 D51# AGTL+ I/O B8 GND Power/Other D16 D52# AGTL+ I/O D18 GND Power/Other A23 D53# AGTL+ I/O D2 GND Power/Other C21 D54# AGTL+ I/O D22 GND Power/Other C19 D55# AGTL+ I/O D26 GND Power/Other C27 D56# AGTL+ I/O D30 GND Power/Other A19 D57# AGTL+ I/O D34 GND Power/Other C23 D58# AGTL+ I/O D4 GND Power/Other C17 D59# AGTL+ I/O E11 GND Power/Other A25 D60# AGTL+ I/O E15 GND Power/Other A27 D61# AGTL+ I/O E19 GND Power/Other E25 D62# AGTL+ I/O E7 GND Power/Other F16 D63# AGTL+ I/O F20 GND Power/Other AL27 DBSY# AGTL+ I/O F24 GND Power/Other AN19 DEFER# AGTL+ Input F28 GND Power/Other C33 DEP0# AGTL+ I/O F32 GND Power/Other 55 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. 56 Pin Name Signal Group Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. Pin Name Signal Group F36 GND Power/Other V2 GND Power/Other G5 GND Power/Other V34 GND Power/Other H2 GND Power/Other X32 GND Power/Other H34 GND Power/Other X36 GND Power/Other K36 GND Power/Other Y37 GND Power/Other L5 GND Power/Other Y5 GND Power/Other M2 GND Power/Other Z2 GND Power/Other M34 GND Power/Other Z34 GND Power/Other P32 GND Power/Other AL25 HIT# AGTL+ I/O P36 GND Power/Other AL23 HITM# AGTL+ I/O A37 GND Power/Other AE35 IERR# CMOS Output AB32 GND Power/Other AG37 IGNNE# CMOS Input AC33 GND Power/Other AG33 INIT# CMOS Input AC5 GND Power/Other M36 LINT0/INTR CMOS Input AD2 GND Power/Other L37 LINT1/NMI CMOS Input AD34 GND Power/Other AK20 LOCK# AGTL+ I/O AF32 GND Power/Other J33 PICCLK APIC Clock Input AF36 GND Power/Other J35 PICD0 APIC I/O AG5 GND Power/Other L35 PICD1 APIC I/O AH2 GND Power/Other W33 PLL1 Power/Other AH34 GND Power/Other U33 PLL2 Power/Other AJ11 GND Power/Other A35 PRDY# AGTL+ Output AJ15 GND Power/Other J37 PREQ# CMOS Input AJ19 GND Power/Other AK26 PWRGOOD CMOS Input AJ23 GND Power/Other AK18 REQ0# AGTL+ I/O AJ27 GND Power/Other AH16 REQ1# AGTL+ I/O AJ3 GND Power/Other AH18 REQ2# AGTL+ I/O AJ7 GND Power/Other AL19 REQ3# AGTL+ I/O AK36 GND Power/Other AL17 REQ4# AGTL+ I/O AK4 GND Power/Other G37 Reserved Reserved for future use AL1 GND Power/Other L33 Reserved Reserved for future use AL3 GND Power/Other N33 Reserved Reserved for future use AM10 GND Power/Other N35 Reserved Reserved for future use AM14 GND Power/Other N37 Reserved Reserved for future use AM18 GND Power/Other Q33 Reserved Reserved for future use Q5 GND Power/Other Q35 Reserved Reserved for future use R34 GND Power/Other Q37 Reserved Reserved for future use T32 GND Power/Other R2 Reserved Reserved for future use T36 GND Power/Other W35 Reserved Reserved for future use U5 GND Power/Other Y1 Reserved Reserved for future use Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. AK30 AM2 Datasheet 6 Pin Name Reserved Signal Group Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. Reserved for future use F30 Pin Name Signal Group VCCCORE Power/Other Reserved Reserved for future use F34 VCCCORE Power/Other F10 Reserved Reserved for future use F4 VCCCORE Power/Other X2 BR1#8 AGTL+ Input H32 VCCCORE Power/Other AH4 RESET# 2 AGTL+ Input H36 VCCCORE Power/Other 2 X4 RESET2# AGTL+ I/O J5 VCCCORE Power/Other AN23 RP# AGTL+ I/O K2 VCCCORE Power/Other AH26 RS0# AGTL + Input K32 VCCCORE Power/Other AH22 RS1# AGTL+ Input K34 VCCCORE Power/Other AK28 RS2# AGTL+ Input M32 VCCCORE Power/Other AC37 RSP# AGTL+ Input N5 VCCCORE Power/Other S35 RTTCTRL Power/Other P2 VCCCORE Power/Other E27 SLEWCTRL Power/Other P34 VCCCORE Power/Other AH30 SLP# CMOS Input R32 VCCCORE Power/Other AJ35 SMI# CMOS Input R36 VCCCORE Power/Other AG35 STPCLK# CMOS Input S5 VCCCORE Power/Other AL33 TCK TAP Input T2 VCCCORE Power/Other AN35 TDI TAP Input T34 VCCCORE Power/Other AN37 TDO TAP Output V32 VCCCORE Power/Other AL29 THERMDN Power/Other V36 VCCCORE Power/Other AL31 THERMDP Power/Other W5 VCCCORE Power/Other AH28 THERMTRIP# CMOS Output X34 VCCCORE Power/Other AK32 TMS TAP Input Y35 VCCCORE Power/Other AN25 TRDY# AGTL+ Input Z32 VCCCORE Power/Other AN33 TRST# TAP Input AF2 VCCCORE Power/Other AD36 VCC1.5 3 Power/Other AF34 VCCCORE Power/Other Z36 VCC2.5 1 Power/Other AH24 VCCCORE Power/Other AB36 VCCCMOS Power/Other AH32 VCCCORE Power/Other AA37 VCCCORE Power/Other AH36 VCCCORE Power/Other AA5 VCCCORE Power/Other AJ13 VCCCORE Power/Other AB2 VCCCORE Power/Other AJ17 VCCCORE Power/Other AB34 VCCCORE Power/Other AJ21 VCCCORE Power/Other AD32 VCCCORE Power/Other AJ25 VCCCORE Power/Other AE5 VCCCORE Power/Other AJ29 VCCCORE Power/Other E5 VCCCORE Power/Other AJ5 VCCCORE Power/Other E9 VCCCORE Power/Other AK2 VCCCORE Power/Other F14 VCCCORE Power/Other AK34 VCCCORE Power/Other F2 VCCCORE Power/Other AM12 VCCCORE Power/Other F22 VCCCORE Power/Other AM16 VCCCORE Power/Other F26 VCCCORE Power/Other AM20 VCCCORE Power/Other 57 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. 58 Pin Name Signal Group Table 29. Signal Listing in Order by Signal Name (Continued) Pin No. Pin Name VID2 Signal Group AM24 VCCCORE Power/Other AL37 Power/Other AM28 VCCCORE Power/Other AJ37 VID3 Power/Other AM32 VCCCORE Power/Other E33 VREF0 Power/Other AM4 VCCCORE Power/Other F18 VREF1 Power/Other AM8 VCCCORE Power/Other K4 VREF2 Power/Other B10 VCCCORE Power/Other R6 VREF3 Power/Other B14 VCCCORE Power/Other V6 VREF4 Power/Other B18 VCCCORE Power/Other AD6 VREF5 Power/Other B22 VCCCORE Power/Other AK12 VREF6 Power/Other B26 VCCCORE Power/Other AK22 VREF7 Power/Other B30 VCCCORE Power/Other AH20 VTT Power/Other B34 VCCCORE Power/Other AK16 VTT Power/Other B6 VCCCORE Power/Other AL13 VTT Power/Other C3 VCCCORE Power/Other AL21 VTT Power/Other D20 VCCCORE Power/Other AN11 VTT Power/Other D24 VCCCORE Power/Other AN15 VTT Power/Other D28 VCCCORE Power/Other G35 VTT Power/Other 4 Power/Other D32 VCCCORE Power/Other AA33 VTT D36 VCCCORE Power/Other AA35 VTT 4 Power/Other 4 Power/Other D6 VCCCORE Power/Other AN21 VTT E13 VCCCORE Power/Other E23 VTT 4 Power/Other Power/Other E17 VCCCORE Power/Other S33 VTT 4 AJ9 VCCCORE Power/Other S37 VTT 4 Power/Other 4 Power/Other Power/Other E21 RESERVE Power/Other U35 VTT AL35 VID0 Power/Other U37 VTT 4 AM36 VID1 Power/Other Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 30. Signal Listing in Order by Pin Number Pin No. A3 Datasheet Pin Name D29# Signal Group AGTL+ I/O Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. AD34 Pin Name GND Signal Group Power/Other 3 A5 D28# AGTL+ I/O AD36 VCC1.5 A7 D43# AGTL+ I/O AE1 A17# A9 D37# AGTL+ I/O AE3 A22# AGTL+ I/O A11 D44# AGTL+ I/O AE5 VCCCORE Power/Other A13 D51# AGTL+ I/O AE33 A20M# CMOS Input A15 D47# AGTL+ I/O AE35 IERR# CMOS Output A17 D48# AGTL+ I/O AE37 FLUSH# CMOS Input A19 D57# AGTL+ I/O AF2 VCCCORE Power/Other A21 D46# AGTL+ I/O AF4 A35# AGTL+ I/O A23 D53# AGTL+ I/O AF6 A25# AGTL+ I/O A25 D60# AGTL+ I/O AF32 GND Power/Other A27 D61# AGTL+ I/O AF34 VCCCORE Power/Other A29 DEP7# AGTL+ I/O AF36 GND Power/Other A31 DEP3# AGTL+ I/O AG1 EDGCTRL 5 Power/Other A33 DEP2# AGTL+ I/O AG3 A19# AGTL+ I/O A35 PRDY# AGTL+ Output AG5 GND Power/Other A37 GND Power/Other AG33 INIT# CMOS Input AA1 A27# AGTL+ I/O AG35 STPCLK# CMOS Input AA3 A30# AGTL+ I/O AG37 IGNNE# CMOS Input AA5 VCCCORE Power/Other AH2 GND Power/Other AA33 VTT 4 Power/Other AH4 RESET# 2 AGTL+ Input AA35 4 Power/Other AH6 A10# AGTL+ I/O AA37 VCCCORE Power/Other AH8 A5# AGTL+ I/O AB2 VCCCORE Power/Other AH10 A8# AGTL+ I/O AB4 A24# AGTL+ I/O AH12 A4# AGTL+ I/O AB6 A23# AGTL+ I/O AH14 BNR# AGTL+ I/O VTT Power/Other AGTL+ I/O AB32 GND Power/Other AH16 REQ1# AGTL+ I/O AB34 VCCCORE Power/Other AH18 REQ2# AGTL+ I/O AB36 VCCCMOS Power/Other AH20 VTT Power/Other AC1 A33# AGTL+ I/O AH22 RS1# AGTL+ Input AC3 A20# AGTL+ I/O AH24 VCCCORE Power/Other AC5 GND Power/Other AH26 RS0# AGTL + Input AC33 GND Power/Other AH28 THERMTRIP# CMOS Output AC35 FERR# CMOS Output AH30 SLP# CMOS Input AC37 RSP# AGTL+ Input AH32 VCCCORE Power/Other AD2 GND Power/Other AH34 GND Power/Other AD4 A31# AGTL+ I/O AH36 VCCCORE Power/Other AD6 VREF5 Power/Other AJ1 A21# AGTL+ I/O AD32 VCCCORE Power/Other AJ3 GND Power/Other 59 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. AJ5 60 Pin Name VCCCORE Signal Group Power/Other Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. Pin Name Signal Group AL11 AP0# AGTL+ I/O AJ7 GND Power/Other AL13 VTT Power/Other AJ9 VCCCORE Power/Other AL15 A7# AGTL+ I/O AJ11 GND Power/Other AL17 REQ4# AGTL+ I/O AJ13 VCCCORE Power/Other AL19 REQ3# AGTL+ I/O AJ15 GND Power/Other AL21 VTT Power/Other AJ17 VCCCORE Power/Other AL23 HITM# AGTL+ I/O AJ19 GND Power/Other AL25 HIT# AGTL+ I/O AJ21 VCCCORE Power/Other AL27 DBSY# AGTL+ I/O AJ23 GND Power/Other AL29 THERMDN Power/Other AJ25 VCCCORE Power/Other AL31 THERMDP Power/Other AJ27 GND Power/Other AL33 TCK TAP Input AJ29 VCCCORE Power/Other AL35 VID0 Power/Other AJ31 BSEL1 Power/Other AL37 VID2 Power/Other AJ33 BSEL0 Power/Other AM2 6 Reserved Reserved for future use AJ35 SMI# CMOS Input AM4 VCCCORE Power/Other AJ37 VID3 Power/Other AM6 GND Power/Other AK2 VCCCORE Power/Other AM8 VCCCORE Power/Other AK4 GND Power/Other AM10 GND Power/Other AK6 A28# AGTL+ I/O AM12 VCCCORE Power/Other AK8 A3# AGTL+ I/O AM14 GND Power/Other AK10 A11# AGTL+ I/O AM16 VCCCORE Power/Other AK12 VREF6 Power/Other AM18 GND Power/Other AK14 A14# AGTL+ I/O AM20 VCCCORE Power/Other AK16 VTT Power/Other AM22 GND Power/Other AK18 REQ0# AGTL+ I/O AM24 VCCCORE Power/Other AK20 LOCK# AGTL+ I/O AM26 GND Power/Other AK22 VREF7 Power/Other AM28 VCCCORE Power/Other AK24 AERR# AGTL+ I/O AM30 GND Power/Other AK26 PWRGOOD CMOS Input AM32 VCCCORE Power/Other AK28 RS2# AGTL+ Input AM34 GND Power/Other AK30 Reserved Reserved for future use AM36 VID1 Power/Other AK32 TMS TAP Input AN3 GND Power/Other AK34 VCCCORE Power/Other AN5 A12# AGTL+ I/O AK36 GND Power/Other AN7 A16# AGTL+ I/O AL1 GND Power/Other AN9 A6# AGTL+ I/O AL3 GND Power/Other AN11 VTT Power/Other AL5 A15# AGTL+ I/O AN13 AP1# AGTL+ I/O AL7 A13# AGTL+ I/O AN15 VTT Power/Other AL9 A9# AGTL+ I/O AN17 BPRI# AGTL+ Input Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. Datasheet Pin Name Signal Group Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. Pin Name Signal Group AN19 DEFER# AGTL+ Input C25 D50# AGTL+ I/O 4 AN21 VTT Power/Other C27 D56# AGTL+ I/O AN23 RP# AGTL+ I/O C29 DEP5# AGTL+ I/O AN25 TRDY# AGTL+ Input C31 DEP1# AGTL+ I/O AN27 DRDY# AGTL+ I/O C33 DEP0# AGTL+ I/O AN29 BR0# AGTL+ I/O C35 BPM0# AGTL+ I/O AN31 ADS# AGTL+ I/O C37 CPUPRES# Power/Other AN33 TRST# TAP Input D2 GND Power/Other AN35 TDI TAP Input D4 GND Power/Other AN37 TDO TAP Output D6 VCCCORE Power/Other B2 D35# AGTL+ I/O D8 D38# AGTL+ I/O B4 GND Power/Other D10 D39# AGTL+ I/O B6 VCCCORE Power/Other D12 D42# AGTL+ I/O B8 GND Power/Other D14 D41# AGTL+ I/O B10 VCCCORE Power/Other D16 D52# AGTL+ I/O B12 GND Power/Other D18 GND Power/Other B14 VCCCORE Power/Other D20 VCCCORE Power/Other B16 GND Power/Other D22 GND Power/Other B18 VCCCORE Power/Other D24 VCCCORE Power/Other B20 GND Power/Other D26 GND Power/Other B22 VCCCORE Power/Other D28 VCCCORE Power/Other B24 GND Power/Other D30 GND Power/Other B26 VCCCORE Power/Other D32 VCCCORE Power/Other B28 GND Power/Other D34 GND Power/Other B30 VCCCORE Power/Other D36 VCCCORE Power/Other B32 GND Power/Other E1 D26# AGTL+ I/O B34 VCCCORE Power/Other E3 D25# AGTL+ I/O B36 BINIT# AGTL+ I/O E5 VCCCORE Power/Other C1 D33# AGTL+ I/O E7 GND Power/Other C3 VCCCORE Power/Other E9 VCCCORE Power/Other C5 D31# AGTL+ I/O E11 GND Power/Other C7 D34# AGTL+ I/O E13 VCCCORE Power/Other C9 D36# AGTL+ I/O E15 GND Power/Other C11 D45# AGTL+ I/O E17 VCCCORE Power/Other C13 D49# AGTL+ I/O E19 GND Power/Other C15 D40# AGTL+ I/O E21 RESERVE Power/Other C17 D59# AGTL+ I/O E23 VTT 4 Power/Other C19 D55# AGTL+ I/O E25 D62# AGTL+ I/O C21 D54# AGTL+ I/O E27 SLEWCTRL Power/Other C23 D58# AGTL+ I/O E29 DEP6# AGTL+ I/O 61 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. E31 62 Pin Name DEP4# Signal Group AGTL+ I/O Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. Pin Name Signal Group K2 VCCCORE Power/Other E33 VREF0 Power/Other K4 VREF2 Power/Other E35 BPM1# AGTL+ I/O K6 D24# AGTL+ I/O E37 BP3# AGTL+ I/O K32 VCCCORE Power/Other F2 VCCCORE Power/Other K34 VCCCORE Power/Other F4 VCCCORE Power/Other K36 GND Power/Other F6 D32# AGTL+ I/O L1 D13# AGTL+ I/O F8 D22# AGTL+ I/O L3 D20# AGTL+ I/O F10 Reserved Reserved for future use L5 GND Power/Other F12 D27# AGTL+ I/O L33 Reserved Reserved for future use F14 VCCCORE Power/Other L35 PICD1 APIC I/O F16 D63# AGTL+ I/O L37 LINT1/NMI CMOS Input F18 VREF1 Power/Other M2 GND Power/Other F20 GND Power/Other M4 D11# AGTL+ I/O F22 VCCCORE Power/Other M6 D3# AGTL+ I/O F24 GND Power/Other M32 VCCCORE Power/Other F26 VCCCORE Power/Other M34 GND Power/Other F28 GND Power/Other M36 LINT0/INTR CMOS Input F30 VCCCORE Power/Other N1 D2# AGTL+ I/O F32 GND Power/Other N3 D14# AGTL+ I/O F34 VCCCORE Power/Other N5 VCCCORE Power/Other F36 GND Power/Other N33 Reserved Reserved for future use G1 D21# AGTL+ I/O N35 Reserved Reserved for future use G3 D23# AGTL+ I/O N37 Reserved Reserved for future use G5 GND Power/Other P2 VCCCORE Power/Other G33 BP2# AGTL+ I/O P4 D18# AGTL+ I/O G35 VTT Power/Other P6 D9# AGTL+ I/O G37 Reserved Reserved for future use P32 GND Power/Other H2 GND Power/Other P34 VCCCORE Power/Other H4 D16# AGTL+ I/O P36 GND Power/Other H6 D19# AGTL+ I/O Q1 D12# AGTL+ I/O H32 VCCCORE Power/Other Q3 D10# AGTL+ I/O H34 GND Power/Other Q5 GND Power/Other H36 VCCCORE Power/Other Q33 Reserved Reserved for future use J1 D7# AGTL+ I/O Q35 Reserved Reserved for future use J3 D30# AGTL+ I/O Q37 Reserved Reserved for future use J5 VCCCORE Power/Other R2 Reserved Reserved for future use J33 PICCLK APIC Clock Input R4 D17# AGTL+ I/O J35 PICD0 APIC I/O R6 VREF3 Power/Other J37 PREQ# CMOS Input R32 VCCCORE Power/Other Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. R34 Datasheet Pin Name Signal Group Table 30. Signal Listing in Order by Pin Number (Continued) Pin No. Pin Name Signal Group GND Power/Other V36 VCCCORE Power/Other R36 VCCCORE Power/Other W1 D0# AGTL+ I/O S1 D8# AGTL+ I/O W3 A34# AGTL+ I/O S3 D5# AGTL+ I/O W5 VCCCORE Power/Other S5 VCCCORE Power/Other W33 PLL1 Power/Other S33 VTT 4 Power/Other W35 Reserved Reserved for future use S35 RTTCTRL Power/Other W37 BCLK System Bus Clock S37 VTT 4 Power/Other X2 BR1#8 AGTL+ input T2 VCCCORE Power/Other X4 RESET2# 2 AGTL+ I/O T4 D1# AGTL+ I/O X6 A32# AGTL+ I/O T6 D6# AGTL+ I/O X32 GND Power/Other T32 GND Power/Other X34 VCCCORE Power/Other T34 VCCCORE Power/Other X36 GND Power/Other T36 GND Power/Other Y1 Reserved Reserved for future use U1 D4# AGTL+ I/O Y3 A26# AGTL+ I/O U3 D15# AGTL+ I/O Y5 GND Power/Other U5 GND Power/Other Y33 CLKREF 7 Power/Other U33 PLL2 Power/Other Y35 VCCCORE Power/Other U35 VTT 4 Power/Other Y37 GND Power/Other U37 VTT 4 Power/Other Z2 GND Power/Other V2 GND Power/Other Z4 A29# AGTL+ I/O V4 BERR# AGTL+ I/O Z6 A18# AGTL+ I/O V6 VREF4 Power/Other Z32 VCCCORE Power/Other V32 VCCCORE Power/Other Z34 GND Power/Other V34 GND Power/Other Z36 VCC2.5 1 Power/Other 63 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 6.0 Boxed Processor Specifications The Intel(R) Pentium(R) III processor for the PGA370 socket is also offered as an Intel boxed processor. Intel boxed processors are intended for system integrators who build systems from motherboards and standard components. The boxed Pentium(R) III processor for the PGA370 socket will be supplied with an unattached fan heatsink. This section documents motherboard and system requirements for the fan heatsink that will be supplied with the boxed Pentium III processor. This section is particularly important for OEMs that manufacture motherboards for system integrators. Unless otherwise noted, all figures in this section are dimensioned in inches. Figure 22 shows a mechanical representation of the boxed Intel Pentium(R) III processor for the PGA370 socket in the Flip Chip Pin Grid Array (FC-PGA) package. Note: Drawings in this section reflect only the specifications on the Intel Boxed Processor product. These dimensions should not be used as a generic keep-out zone for all heatsinks. It is the system designer's responsibility to consider their proprietary solution when designing to the required keepout zone on their system platform and chassis. Refer to the Intel(R) Pentium(R) III Processor Thermal/ Mechanical Functional Specifications for further guidance. Contact your local Intel Sales Representative for this document. Figure 22. Conceptual Boxed Intel(R) Pentium(R) III Processor for the PGA370 Socket 6.1 Mechanical Specifications for the Boxed Intel(R) Pentium(R) III Processor 6.1.1 Boxed Processor Thermal Cooling Solution Dimensions This section documents the mechanical specifications of the boxed Intel Pentium processor fan heatsink in the FC-PGA package. The boxed processor in the FC-PGA package ships with an unattached fan heatsink. Figure 22 shows a mechanical representation of the boxed Intel Pentium III processor for the PGA370 socket in the Flip Chip Pin Grid Array (FC-PGA) package. The dimensions for the boxed processor with integrated fan heatsink are shown in Figure 23, Figure 24, and Figure 25. There are three versions of the fan heatsink. The smallest solution is shown in Figure 23 for 500 to 850MHz. The larger cooling solution Figure 24 is required for Pentium III processors at frequencies of 866 to 933MHz. Figure 25 is the largest boxed processor fan heatsink and is used for 1 GHz Pentium (R) III processor. General spatial specifications are also outlined in Table 31. All dimensions are in inches unless otherwise noted. 64 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz The fan heatsink is designed to allow visibility of the FC-PGA processor markings located on top of the package. The FC-PGA processor markings are visible after installation of the fan heatsink due to notched sides of the heatsink base (specified in Figure 27). The boxed processor fan heatsink is also asymmetrical in that the mechanical step feature (specified in Figure 26) must sit over the socket's cam. The step allows the heatsink to securely interface with the processor in order to meet thermal requirements. Note: The heatsink airflow keepout zones found in Table 31 and Figure 29 refer specifically to the boxed processor's active fan heatsink. This does not reflect the worst-case dimensions that may exist with other third party passive or active fan heatsinks. Figure 23. Space Requirements for the Boxed Processor to 850MHz Figure 24. Space Requirements for the Boxed Processor from 866 to 933MHz Datasheet 65 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 25. Space Requirements for the Boxed Processor at 1 GHz Table 31. Boxed Processor Fan Heatsink Spatial Dimensionsa Dimensions (Inches) Min Typ Fan Heatsink Length (see figure 23) Max 2.52 Fan Heatsink for 866 to 933 MHz Length (figure 24) 2.68 Fan Heatsink Length for 1 GHz (see figure 25) 3.17 Fan Heatsink Height (see figure 23) 1.75 Fan Heatsink for 866 to 933 MHz Height (figure 24) 1.78 Fan Heatsink Height for 1 GHz (see figure 25) 1.89 Fan Heatsink Width (see figure 23) 2.00 Fan Heatsink for 866 to 933 MHz Width (figure 24) 2.65 Fan Heatsink Width for 1 GHz (see figure 25) 2.65 Dimensions (Inches) Min Typ Max Fan Heatsink height above motherboard for all frequencies .30 .29 .33 Air Keepout Zones from end of Fan Heatsink for all frequencies .20 a. Drawings reflect only the specification of the Intel boxed processor product. These dimensions should not be used as a universal keepout zone that covers all heatsinks. It is the system designer's responsibility to consider their own proprietary solution when designing the desired keepout zone in their system platform. Figure 26. Dimensions of Mechanical Step Feature in Heatsink Base 0.043 0.472 66 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 6.1.2 Boxed Processor Heatsink Weight The boxed processor thermal cooling solution will not weigh more than 180 grams. Figure 27. Dimensions of Notches in Heatsink Base 6.1.3 Boxed Processor Thermal Cooling Solution Clip The boxed processor thermal solution requires installation by a system integrator to secure the thermal cooling solution to the processor after it is installed in the 370-pin socket ZIF socket. Motherboards designed for use by system integrators should take care to consider the implications of clip installation and potential scraping of the motherboard PCB underneath the 370-pin socket attach tabs. Motherboard components should not be placed too close to the 370-pin socket attach tabs in a way that interferes with the installation of the boxed processor thermal cooling solution (see Figure 28 for specification). Datasheet 67 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 28. Clip Keepout Requirements for the PGA370 (Top View) 6.2 Thermal Specifications This section describes the cooling requirements of the thermal cooling solution utilized by the boxed processor. 6.2.1 Boxed Processor Cooling Requirements The boxed processor is directly cooled with a fan heatsink. However, meeting the processor's temperature specification is also a function of the thermal design of the entire system, an ultimately the responsibility of the system integrator. The processor temperature specification is found in [Section 4.0] of this document. The boxed processor fan heatsink will keep the processor core at the recommended specifications (see Table 24) in chassis that provide good thermal management. For the boxed processor fan heatsink to operate properly, it is critical that the airflow provided to the fan heatsink is unimpeded. Airflow of the fan heatsink is into the center and out of the sides of the fan heatsink. Airspace is required around the fan to ensure that the airflow through the fan heatsink is not blocked. Blocking the airflow to the fan heatsink reduces the cooling efficiency and decreases fan life. Table 31 and Figure 29 illustrate an acceptable airspace clearance for the fan heatsink. It is also recommended that the air temperature entering the fan be kept below 45 C. Meeting the processor's temperature specification is the responsibility of the system integrator. The processor temperature specification is found in [Section 4.0] of this document. 68 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 29. Thermal Airspace Requirement for all Boxed Intel(R) Pentium(R) III Processor Fan Heatsinks in the PGA370 Socket Measure ambient temperature 0.3" above center of fan inlet 0.20 Min Air Space 0.20 Min Air Space Fan Heatsink Processor arsp1.vsd 6.3 Electrical Requirements for the Boxed Intel(R) Pentium(R) III Processor 6.3.1 Fan Heatsink Power Supply The boxed processor's fan heatsink requires a +12 V power supply. A fan power cable is attached to the fan and will draw power from a power header on the motherboard. The power cable connector and pinout are shown in Figure 30. Motherboards must provide a matched power header to support the boxed processor. Table 32 contains specifications for the input and output signals at the fan heatsink connector. The fan heatsink outputs a SENSE (open-collector output) signal that pulses at a rate of two pulses per fan revolution. A motherboard pull-up resistor provides VOH to match the motherboard-mounted fan speed monitor requirements, if applicable. Use of the SENSE signal is optional. If the SENSE signal is not used, pin 3 of the connector should be tied to GND. The power header on the baseboard must be positioned to allow the fan heatsink power cable to reach it. The power header identification and location should be documented in the motherboard documentation or on the motherboard. Figure 31 shows the recommended location of the fan power connector relative to the PGA370 socket. The motherboard power header should be positioned within 4.00 inches (lateral) from the center of the PGA370 socket. Datasheet 69 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Figure 30. Boxed Processor Fan Heatsink Power Cable Connector Description Pin Signal 1 GND Straight square pin, 3-pin terminal housing with polarizing ribs and friction locking ramp. 2 +12V 0.100" pin pitch, 0.025" square pin width. 3 SENSE Waldom/Molex P/N 22-01-3037 or equivalent. Match with straight pin, friction lock header on motherboard Waldom/Molex P/N 22-23-2031, AMP P/N 640456-3, or equivalent. 1 2 3 Table 32. Fan Heatsink Power and Signal Specifications Description +12 V: 12 volt fan power supply Min Typ Max 10.8 V 12 V 13.2 V IC: Fan current draw 100 mA SENSE: SENSE frequency (motherboard should pull this pin up to appropriate VCC with resistor) 2 pulses per fan revolution Figure 31. Motherboard Power Header Placement Relative to the Boxed Intel(R) Pentium(R) III Processor 0.10" R = 4.00" P G A 3 7 07 Socket 0.10" 70 Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz 7.0 Processor Signal Description This section provides an alphabetical listing of all the Intel(R) Pentium(R) III processor signals. The tables at the end of this section summarize the signals by direction: output, input, and I/O. 7.1 Alphabetical Signals Reference Table 33. Signal Description (Sheet 1 of 8) Name A[35:3]# Type I/O Description The A[35:3]# (Address) signals define a 236-byte physical memory address space. When ADS# is active, these pins transmit the address of a transaction; when ADS# is inactive, these pins transmit transaction type information. These signals must connect the appropriate pins of all agents on the processor system bus. The A[35:24]# signals are parity-protected by the AP1# parity signal, and the A[23:3]# signals are parity-protected by the AP0# parity signal. On the active-to-inactive transition of RESET#, the processors sample the A[35:3]# pins to determine their power-on configuration. See the Intel(R) Pentium(R) II Processor Developer's Manual for details. A20M# I If the A20M# (Address-20 Mask) input signal is asserted, the processor masks physical address bit 20 (A20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at the 1 MB boundary. Assertion of A20M# is only supported in real mode. A20M# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. ADS# AERR# I/O I/O The ADS# (Address Strobe) signal is asserted to indicate the validity of the transaction address on the A[35:3]# pins. All bus agents observe the ADS# activation to begin parity checking, protocol checking, address decode, internal snoop, or deferred reply ID match operations associated with the new transaction. This signal must connect the appropriate pins on all processor system bus agents. The AERR# (Address Parity Error) signal is observed and driven by all processor system bus agents, and if used, must connect the appropriate pins on all processor system bus agents. AERR# observation is optionally enabled during power-on configuration; if enabled, a valid assertion of AERR# aborts the current transaction. If AERR# observation is disabled during power-on configuration, a central agent may handle an assertion of AERR# as appropriate to the error handling architecture of the system. AP[1:0]# BCLK I/O I The AP[1:0]# (Address Parity) signals are driven by the request initiator along with ADS#, A[35:3]#, REQ[4:0]#, and RP#. AP1# covers A[35:24]#, and AP0# covers A[23:3]#. A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. This allows parity to be high when all the covered signals are high. AP[1:0]# should connect the appropriate pins of all processor system bus agents. The BCLK (Bus Clock) signal determines the bus frequency. All processor system bus agents must receive this signal to drive their outputs and latch their inputs on the BCLK rising edge. All external timing parameters are specified with respect to the BCLK signal. Datasheet 71 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 2 of 8) Name Type Description The BERR# (Bus Error) signal is asserted to indicate an unrecoverable error without a bus protocol violation. It may be driven by all processor system bus agents, and must connect the appropriate pins of all such agents, if used. However, Pentium III processors do not observe assertions of the BERR# signal. BERR# I/O BERR# assertion conditions are configurable at a system level. Assertion options are defined by the following options: * Enabled or disabled. * Asserted optionally for internal errors along with IERR#. * Asserted optionally by the request initiator of a bus transaction after it observes an error. * Asserted by any bus agent when it observes an error in a bus transaction. The BINIT# (Bus Initialization) signal may be observed and driven by all processor system bus agents, and if used must connect the appropriate pins of all such agents. If the BINIT# driver is enabled during power on configuration, BINIT# is asserted to signal any bus condition that prevents reliable future information. BINIT# I/O If BINIT# observation is enabled during power-on configuration, and BINIT# is sampled asserted, all bus state machines are reset and any data which was in transit is lost. All agents reset their rotating ID for bus arbitration to the state after Reset, and internal count information is lost. The L1 and L2 caches are not affected. If BINIT# observation is disabled during power-on configuration, a central agent may handle an assertion of BINIT# as appropriate to the error handling architecture of the system. The BNR# (Block Next Request) signal is used to assert a bus stall by any bus agent who is unable to accept new bus transactions. During a bus stall, the current bus owner cannot issue any new transactions. I/O BP[3:2]# I/O The BP[3:2]# (Breakpoint) signals are outputs from the processor that indicate the status of breakpoints. I/O The BPM[1:0]# (Breakpoint Monitor) signals are breakpoint and performance monitor signals. They are outputs from the processor which indicate the status of breakpoints and programmable counters used for monitoring processor performance. BPM[1:0]# BPRI# 72 Since multiple agents might need to request a bus stall at the same time, BNR# is a wire-OR signal which must connect the appropriate pins of all processor system bus agents. In order to avoid wire-OR glitches associated with simultaneous edge transitions driven by multiple drivers, BNR# is activated on specific clock edges and sampled on specific clock edges. BNR# I The BPRI# (Bus Priority Request) signal is used to arbitrate for ownership of the processor system bus. It must connect the appropriate pins of all processor system bus agents. Observing BPRI# active (as asserted by the priority agent) causes all other agents to stop issuing new requests, unless such requests are part of an ongoing locked operation. The priority agent keeps BPRI# asserted until all of its requests are completed, then releases the bus by deasserting BPRI#. Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 3 of 8) Name Type Description The BR0# and BR1# (Bus Request) pins drive the BREQ[1:0]# signals in the system. The BREQ[1:0]# signals are interconnected in a rotating manner to individual processor pins. The table below gives the rotating interconnect between the processor and bus signals. BR0# (I/O) and BR1# Signals Rotating Interconnect BR0# I/O BR1# I Bus Signal Agent 0 Pins Agent 1 Pins BREQ0# BR0# BR1# BREQ1# BR1# BR0# During power-up configuration, the central agent must assert the BR0# bus signal. All symmetric agents sample their BR[1:0]# pins on active-to-inactive transition of RESET#. The pin on which the agent samples an active level determines its symmetric agent ID. All agents then configure their pins to match the appropriate bus signal protocol, as shown below. BR[1:0]# Signal Agent IDs Pin Sampled Active in RESET# Agent ID BR0# 0 BR1# 3 These signals are used to select the system bus frequency. A BSEL[1:0] = "01" selects a 100 MHz system bus frequency and a BSEL[1:0] = "11" selects a 133 MHz system bus frequency. The frequency is determined by the processor(s), chipset, and frequency synthesizer capabilities. All system bus agents must operate at the same frequency. The Pentium III processor for the PGA370 socket operates at 100 MHz and 133 MHz system bus frequencies. Individual processors will only operate at their specified front side bus (FSB) frequency. Either 100 MHz or 133 MHz, not both. BSEL[1:0] I/O On motherboards which support operation at either 66 MHz or 100 MHz, a BSEL[1:0] = "x0" will select a 66 Mhz system bus frequency. 66 MHz operation is not support by the Pentium III processor for the PGA370 socket; therefore, BSEL0 is ignored. These signals must be pulled up to 2.5 V or 3.3V with 1 K resistors and provided as a frequency selection signal to the clock driver/synthesizer. If the system motherboard is not capable of operating at 133 MHz, it should ground the BSEL1 signal and generate a 100 MHz system bus frequency. See Section 2.8.2 for implementation examples. CLKREF Datasheet I The CLKREF input is a filtered 1.25V supply voltage for the processor PLL. A voltage divider and decoupling solution is provided by the motherboard. See the design guide for implementation details. 73 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 4 of 8) Name Type Description The CPUPRES# signal is defined to allow a system design to detect the presence of a terminator device or processor in a PGA370 socket. Combined with the VID combination of VID[3:0]= 1111 (see Section 2.6), a system can determine if a socket is occupied, and whether a processor core is present. See the table below for states and values for determining the presence of a device. PGA370 Socket Occupation Truth Table Signal CPUPRES# Value Status CPUPRES# VID[3:0] 0 Anything other than `1111' Processor core installed in the PGA370 socket. CPUPRES# VID[3:0] 0 1111 Terminator device installed in the PGA370 socket (i.e., no core present). CPUPRES# VID[3:0] 1 Any value PGA370 socket not occupied. I/O The D[63:0]# (Data) signals are the data signals. These signals provide a 64-bit data path between the processor system bus agents, and must connect the appropriate pins on all such agents. The data driver asserts DRDY# to indicate a valid data transfer. I/O The DBSY# (Data Bus Busy) signal is asserted by the agent responsible for driving data on the processor system bus to indicate that the data bus is in use. The data bus is released after DBSY# is deasserted. This signal must connect the appropriate pins on all processor system bus agents. I The DEFER# signal is asserted by an agent to indicate that a transaction cannot be guaranteed in-order completion. Assertion of DEFER# is normally the responsibility of the addressed memory or I/O agent. This signal must connect the appropriate pins of all processor system bus agents. DEP[7:0]# I/O The DEP[7:0]# (Data Bus ECC Protection) signals provide optional ECC protection for the data bus. They are driven by the agent responsible for driving D[63:0]#, and must connect the appropriate pins of all processor system bus agents which use them. The DEP[7:0]# signals are enabled or disabled for ECC protection during power on configuration. DRDY# I/O The DRDY# (Data Ready) signal is asserted by the data driver on each data transfer, indicating valid data on the data bus. In a multi-cycle data transfer, DRDY# may be deasserted to insert idle clocks. This signal must connect the appropriate pins of all processor system bus agents. EDGCTRL O The EDGCTRL input adjusts the edge rate of AGTL+ output buffers for previous processors and should be pulled up to VCCCORE with a 51 5% resistor. See the platform design guide for implementation details. This signal is not used by the Pentium III processor. FERR# O The FERR# (Floating-point Error) signal is asserted when the processor detects an unmasked floating-point error. FERR# is similar to the ERROR# signal on the Intel 387 coprocessor, and is included for compatibility with systems using MS-DOS*-type floating-point error reporting. D[63:0]# DBSY# DEFER# 74 O Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 5 of 8) Name Type Description When the FLUSH# input signal is asserted, processors write back all data in the Modified state from their internal caches and invalidate all internal cache lines. At the completion of this operation, the processor issues a Flush Acknowledge transaction. The processor does not cache any new data while the FLUSH# signal remains asserted. FLUSH# I FLUSH# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. On the active-to-inactive transition of RESET#, each processor samples FLUSH# to determine its power-on configuration. See the P6 Family of Processors Hardware Developer's Manual for details. HIT# I/O HITM# I/O IERR# IGNNE# O I The HIT# (Snoop Hit) and HITM# (Hit Modified) signals convey transaction snoop operation results, and must connect the appropriate pins of all processor system bus agents. Any such agent may assert both HIT# and HITM# together to indicate that it requires a snoop stall, which can be continued by reasserting HIT# and HITM# together. The IERR# (Internal Error) signal is asserted by a processor as the result of an internal error. Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the processor system bus. This transaction may optionally be converted to an external error signal (e.g., NMI) by system core logic. The processor will keep IERR# asserted until the assertion of RESET#, BINIT#, or INIT#. The IGNNE# (Ignore Numeric Error) signal is asserted to force the processor to ignore a numeric error and continue to execute noncontrol floating-point instructions. If IGNNE# is deasserted, the processor generates an exception on a noncontrol floating-point instruction if a previous floating-point instruction caused an error. IGNNE# has no effect when the NE bit in control register 0 is set. IGNNE# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. INIT# I The INIT# (Initialization) signal, when asserted, resets integer registers inside all processors without affecting their internal (L1 or L2) caches or floating-point registers. Each processor then begins execution at the power-on Reset vector configured during power-on configuration. The processor continues to handle snoop requests during INIT# assertion. INIT# is an asynchronous signal and must connect the appropriate pins of all processor system bus agents. If INIT# is sampled active on the active to inactive transition of RESET#, then the processor executes its Built-in Self-Test (BIST). LINT[1:0] I The LINT[1:0] (Local APIC Interrupt) signals must connect the appropriate pins of all APIC Bus agents, including all processors and the core logic or I/O APIC component. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and LINT1 becomes NMI, a nonmaskable interrupt. INTR and NMI are backward compatible with the signals of those names on the Intel(R) Pentium(R) processor. Both signals are asynchronous. Both of these signals must be software configured via BIOS programming of the APIC register space to be used either as NMI/INTR or LINT[1:0]. Because the APIC is enabled by default after Reset, operation of these pins as LINT[1:0] is the default configuration. LOCK# Datasheet I/O The LOCK# signal indicates to the system that a transaction must occur atomically. This signal must connect the appropriate pins of all processor system bus agents. For a locked sequence of transactions, LOCK# is asserted from the beginning of the first transaction end of the last transaction. When the priority agent asserts BPRI# to arbitrate for ownership of the processor system bus, it will wait until it observes LOCK# deasserted. This enables symmetric agents to retain ownership of the processor system bus throughout the bus locked operation and ensure the atomicity of lock. 75 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 6 of 8) Name Type Description I The PICCLK (APIC Clock) signal is an input clock to the processor and core logic or I/O APIC which is required for operation of all processors, core logic, and I/O APIC components on the APIC bus. I/O The PICD[1:0] (APIC Data) signals are used for bidirectional serial message passing on the APIC bus, and must connect the appropriate pins of all processors and core logic or I/O APIC components on the APIC bus. PLL1, PLL2 I All Pentium III processors have an internal analog PLL clock generator that requires a quiet power supply. PLL1 and PLL2 are inputs to this PLL and must be connected to VCCCORE through a low pass filter that minimizes jitter. See the platform design guide for implementation details. PRDY# O The PRDY (Probe Ready) signal is a processor output used by debug tools to determine processor debug readiness. PREQ# I The PREQ# (Probe Request) signal is used by debug tools to request debug operation of the processors. PICCLK PICD[1:0] PWRGOOD I The PWRGOOD (Power Good) signal is processor input. The processor requires this signal to be a clean indication that the clocks and power supplies (VCCCORE, etc.) are stable and within their specifications. Clean implies that the signal will remain low (capable of sinking leakage current), without glitches, from the time that the power supplies are turned on until they come within specification. The signal must then transition monotonically to a high state. The figure below illustrates the relationship of PWRGOOD to other system signals. PWRGOOD can be driven inactive at any time, but clocks and power must again be stable before a subsequent rising edge of PWRGOOD. It must also meet the minimum pulse width specification in Table 13, and be followed by a 1 ms RESET# pulse. The PWRGOOD signal must be supplied to the processor; it is used to protect internal circuits against voltage sequencing issues. It should be driven high throughout boundary scan operation. REQ[4:0]# I/O The REQ[4:0]# (Request Command) signals must connect the appropriate pins of all processor system bus agents. They are asserted by the current bus owner over two clock cycles to define the currently active transaction type. Asserting the RESET# signal resets all processors to known states and invalidates their L1 and L2 caches without writing back any of their contents. For a power-on Reset, RESET# must stay active for at least one millisecond after VCCCORE and CLK have reached their proper specifications. On observing active RESET#, all processor system bus agents will deassert their outputs within two clocks. RESET# I A number of bus signals are sampled at the active-to-inactive transition of RESET# for power-on configuration. These configuration options are described in the P6 Family of Processors Hardware Developer's Manual for details. The processor may have its outputs tristated via power-on configuration. Otherwise, if INIT# is sampled active during the active-to-inactive transition of RESET#, the processor will execute its Built-in Self-Test (BIST). Whether or not BIST is executed, the processor will begin program execution at the power on Reset vector (default 0_FFFF_FFF0h). RESET# must connect the appropriate pins of all processor system bus agents. RESET2# RP# RS[2:0]# 76 I I/O I The RESET2# pin is provided for compatibility with other Intel Architecture processors. The Pentium III processor does not use the RESET2# pin. Refer to the platform design guide for the proper connections of this signal. The RP# (Request Parity) signal is driven by the request initiator, and provides parity protection on ADS# and REQ[4:0]#. It must connect the appropriate pins of all processor system bus agents. A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. This definition allows parity to be high when all covered signals are high. The RS[2:0]# (Response Status) signals are driven by the response agent (the agent responsible for completion of the current transaction), and must connect the appropriate pins of all processor system bus agents. Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 7 of 8) Name Description The RSP# (Response Parity) signal is driven by the response agent (the agent responsible for completion of the current transaction) during assertion of RS[2:0]#, the signals for which RSP# provides parity protection. It must connect the appropriate pins of all processor system bus agents. RSP# I RTTCTRL I The RTTCTRL input signal provides AGTL+ termination control. The Pentium III processor samples this input to sense the presence of motherboard AGTL+ termination. See the platform design guide for implementation details. SLEWCTRL I The SLEWCTRL input signal provides AGTL+ slew rate control. The Pentium III processor samples this input to determine the slew rate for AGTL+ signals when it is the driving agent. See the platform design guide for implementation details. I The SLP# (Sleep) signal, when asserted in Stop-Grant state, causes processors to enter the Sleep state. During Sleep state, the processor stops providing internal clock signals to all units, leaving only the Phase-Locked Loop (PLL) still operating. Processors in this state will not recognize snoops or interrupts. The processor will recognize only assertions of the SLP#, STPCLK#, and RESET# signals while in Sleep state. If SLP# is deasserted, the processor exits Sleep state and returns to Stop-Grant state, restarting its internal clock signals to the bus and APIC processor core units. I The SMI# (System Management Interrupt) signal is asserted asynchronously by system logic. On accepting a System Management Interrupt, processors save the current state and enter System Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins program execution from the SMM handler. STPCLK# I The STPCLK# (Stop Clock) signal, when asserted, causes processors to enter a low power Stop-Grant state. The processor issues a Stop-Grant Acknowledge transaction, and stops providing internal clock signals to all processor core units except the bus and APIC units. The processor continues to snoop bus transactions and latch interrupts while in Stop-Grant state. When STPCLK# is deasserted, the processor restarts its internal clock to all units, services pending interrupts while in the Stop-Grant state, and resumes execution. The assertion of STPCLK# has no effect on the bus clock; STPCLK# is an asynchronous input. TCK I The TCK (Test Clock) signal provides the clock input for the processor Test Bus (also known as the Test Access Port). TDI I The TDI (Test Data In) signal transfers serial test data into the processor. TDI provides the serial input needed for JTAG specification support. TDO O The TDO (Test Data Out) signal transfers serial test data out of the processor. TDO provides the serial output needed for JTAG specification support. THERMDN O Thermal Diode Cathode. Used to calculate core (junction) temperature. See Section 4.1. THERMDP I Thermal Diode Anode. Used to calculate core (junction) temperature. See Section 4.1. O The processor protects itself from catastrophic overheating by use of an internal thermal sensor. This sensor is set well above the normal operating temperature to ensure that there are no false trips. The processor will stop all execution when the junction temperature exceeds approximately 135 C. This is signaled to the system by the THERMTRIP# (Thermal Trip) pin. Once activated, the signal remains latched, and the processor stopped, until RESET# goes active. There is no hysteresis built into the thermal sensor itself; as long as the die temperature drops below the trip level, a RESET# pulse will reset the processor and execution will continue. If the temperature has not dropped below the trip level, the processor will continue to drive THERMTRIP# and remain stopped. SLP# SMI# THERMTRIP# Datasheet Type A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. While RS[2:0]# = 000, RSP# is also high, since this indicates it is not being driven by any agent guaranteeing correct parity. 77 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 33. Signal Description (Sheet 8 of 8) Name 7.2 Type Description TMS I The TMS (Test Mode Select) signal is a JTAG specification support signal used by debug tools. TRDY# I The TRDY# (Target Ready) signal is asserted by the target to indicate that it is ready to receive a write or implicit writeback data transfer. TRDY# must connect the appropriate pins of all processor system bus agents. TRST# I The TRST# (Test Reset) signal resets the Test Access Port (TAP) logic. TRST# must be driven low during power on Reset. VID[3:0] O The VID[3:0] (Voltage ID) pins can be used to support automatic selection of power supply voltages. These pins are not signals, but are either an open circuit or a short circuit to VSS on the processor. The combination of opens and shorts defines the voltage required by the processor. The VID pins are needed to cleanly support voltage specification variations on processors. See Table 2 for definitions of these pins. The power supply must supply the voltage that is requested by these pins, or disable itself. VCOREDET O The VCOREDET pin indicate the type of processor core present. This pin will float for 2.0V VCCCORE based processor and will be shorted to VSS for the Pentium III processor. VCC1.5 I The VCC1.5 V input pin provides the termination voltage for CMOS signals interfacing to the processor. The Pentium III processor reroutes the 1.5V input to the VCCCMOS output via the package. The supply for VCC1.5 V must be the same one used to supply VTT. VCC2.5 I The VCC2.5 V input pin provides the termination voltage for CMOS signals interfacing to processors which require 2.5V termination on the CMOS signals. This signal is not used by the Pentium III processor. VCCCMOS O The VCCCMOS pin provides the CMOS voltage for use by the platform and is used for terminating CMOS signals that interface to the processor. VREF I The VREF input pins supply the AGTL+ reference voltage, which is typically 2/3 of VTT. VREF is used by the AGTL+ receivers to determine if a signal is a logical 0 or a logical 1. Signal Summaries Table 34 through Table 37 list attributes of the processor output, input, and I/O signals. Table 34. Output Signals 78 Name Active Level Clock Signal Group CPUPRES# Low Asynch Power/Other EDGCTRL N/A Asynch Power/Other FERR# Low Asynch CMOS Output IERR# Low Asynch CMOS Output PRDY# Low BCLK AGTL+ Output TDO High TCK TAP Output THERMTRIP# Low Asynch CMOS Output VCOREDET N/A Asynch Power/Other VID[3:0] N/A Asynch Power/Other Datasheet Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 35. Input Signals Name Active Level Clock Signal Group Qualified A20M# Low Asynch CMOS Input Always1 BCLK High -- System Bus Clock Always BPRI# Low BCLK AGTL+ Input Always BR1# Low BCLK AGTL+ Input Always DEFER# Low BCLK AGTL+ Input Always FLUSH# Low Asynch CMOS Input Always1 IGNNE# Low Asynch CMOS Input Always1 INIT# Low Asynch CMOS Input Always1 INTR High Asynch CMOS Input APIC disabled mode LINT[1:0] High Asynch CMOS Input APIC enabled mode NMI High Asynch CMOS Input APIC disabled mode PICCLK High -- APIC Clock Always PREQ# Low Asynch CMOS Input Always PWRGOOD High Asynch CMOS Input Always RESET# Low BCLK AGTL+ Input Always RS[2:0]# Low BCLK AGTL+ Input Always Always RSP# Low BCLK AGTL+ Input RTTCTRL N/A Asynch Power/Other SLEWCTRL N/A Asynch Power/Other SLP# Low Asynch CMOS Input SMI# Low Asynch CMOS Input STPCLK# Low Asynch CMOS Input TCK High -- TAP Input TDI High TCK TAP Input TMS High TCK TAP Input TRST# Low Asynch TAP Input TRDY# Low BCLK AGTL+ Input During Stop-Grant state NOTE: 1. Synchronous assertion with active TDRY# ensures synchronization. Datasheet 79 Pentium(R) III Processor for the PGA370 Socket at 500 MHz to 1 GHz Table 36. Input/Output Signals (Single Driver) Name Active Level Clock Signal Group Qualified A[35:3]# Low BCLK AGTL+ I/O ADS#, ADS#+1 ADS# Low BCLK AGTL+ I/O Always AP[1:0]# Low BCLK AGTL+ I/O ADS#, ADS#+1 BP[3:2]# Low BCLK AGTL+ I/O Always BPM[1:0]# Low BCLK AGTL+ I/O Always BR0# Low BCLK AGTL+ I/O Always BSEL[1:0] High Asynch Power/Other Always D[63:0]# Low BCLK AGTL+ I/O DRDY# DBSY# Low BCLK AGTL+ I/O Always DEP[7:0]# Low BCLK AGTL+ I/O DRDY# DRDY# Low BCLK AGTL+ I/O Always LOCK# Low BCLK AGTL+ I/O Always REQ[4:0]# Low BCLK AGTL+ I/O ADS#, ADS#+1 RP# Low BCLK AGTL+ I/O ADS#, ADS#+1 Table 37. Input/Output Signals (Multiple Driver) 80 Name Active Level Clock Signal Group Qualified AERR# Low BCLK AGTL+ I/O ADS#+3 BERR# Low BCLK AGTL+ I/O Always BINIT# Low BCLK AGTL+ I/O Always BNR# Low BCLK AGTL+ I/O Always HIT# Low BCLK AGTL+ I/O Always HITM# Low BCLK AGTL+ I/O Always PICD[1:0] High PICCLK APIC I/O Always Datasheet