This 2” prof essional high quality compr ession driver features a compact, lightweight neodymium rar e-earth magnet system, an integral pure titanium
dome and suspension attached to a lightweight aluminium voice coil. It provides an exceptional high acoustic power output over an extremely
wide frequency range, with reduced harmonic distortion and excellent power handling capacity. The use of a rim centred diaphragm and push
terminals permits simple field replacement without soldering.
CP850/Nd
HIGH FREQUENCY
COMPRESSION
DRIVER
Motor de compresión de 2” de muy alta calidad. Incorpora un sistema magnético ultracompacto y ligero a base de un imán en corona de neodimio,
que genera un campo magnético extremadamente elevado. La bobina de 4” de diámetro, está realizada con hilo rectangular de aluminio y unida a
un diafragma de titanio moldeado a presión.
Proporciona una potencia acústica excepcional, una respuesta en frecuencia muy amplia, y un rendimiento elevado, con una calidad sonora sin
parangón.
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power Capacity*
Program Power
Sensitivity*
Frequency range
Recommended crossover
Voice coil diameter
Magnetic assembly weight
Flux density
BL factor
49 mm. 2 in.
8 ohms.
7.5 ohms @ 2 kHz
5.6 ohm
60 w RMS above 500 Hz
125 w RMS above 1.5 kHz
120 Watts. above 500 Hz
250 Watts. above 1.5 kHz
112 dB 1w @ 1m
coupled to TD-460 horn
0.5 - 20 kHz
500 Hz or higher
100 mm. 4 in.
3.6 kg. 7.9lb.
2 T
16.5 N/A
MOUNTING INFORMATION
165 mm. 6.5 in.
114 mm. 4.5 in.
Four M6 threaded holes, 90° apart
on 101.6 mm (4 in.) diameter circle.
Mounting hardware is supplied.
4.4 kg. 9.7 Ib.
5 kg. 11 Ib.
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Titanium
Edgewound alum. ribbon
Kapton
Neodymium
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
-Pro-
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD460/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD400/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD590 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD460/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD400/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD590 Horn
- 32 -
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
The CP 800/Ti is a high performance compression driver capable of high acoustic output over a wide frequency range. It features an integral pure
titanium dome and surround, a precision lightweight voice coil made from flat aluminium wire, wound on high temperature polymide former and
a massive, powerful magnet structure, providing high energy and the ability to handle extremely high power levels over extended periods of time.
Modelo de compresión de 2” con unas características muy similares al CP850/Nd, aunque con un sistema magnético más macizo al utilizar un
imán de ferrita de gran tamaño. Este modelo se caracteriza por su excelente rendimiento, amplia banda pasante y gran potencia admisible.
-Pro-
CP800/Ti
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power Capacity*
Program Power
Sensitivity*
Frequency range
Recommended
crossover
Voice coil diameter
Magnetic assembly weight
Flux density
BL factor
49 mm. 2 in.
8 ohms.
7.5 ohms @ 1.5 kHz
5.6 ohm
60 w RMS above 500 Hz
125 w RMS above 1.5 kHz
120 Watts. above 500 Hz
250 Watts. above 1.5 kHz
112 dB 1w @ 1m
coupled to TD-460 horn
0.5 - 20 kHz
500 Hz or higher, 12 dB/oct. min.
100 mm. 4 in.
8.9 kg. 19.6lb.
1.75 T
15 N/A
MOUNTING INFORMATION
228 mm. 9 in.
117 mm. 4.6 in.
Four M6 threaded holes, 90° apart
on 101.6 mm (4 in.) diameter circle.
Mounting hardware is supplied.
10.3 kg. 22.7 Ib.
11 kg. 22.4 Ib.
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Titanium
Edgewound alum. ribbon
Kapton
Ferrite
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD460/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD400/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD590 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD460/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD400/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD590 Horn
- 33 -
This 2” high frequency compr ession driv er featur es a lightw eight dia phragm assembly made with pur e titanium material f or the dome and suspension,
attached to a 3” edgewound aluminium ribbon voice coil, providing exceptional high acoustic pressure over an extremely wide frequency range.
A short-circuit copper ring over pole piece reduces dramatically the harmonic distortion and maintains a constant impedance response. The use
of a rim centred diaphragm and push terminals permits simple field replacement without soldering.
CP650/Ti
HIGH FREQUENCY
COMPRESSION
DRIVER
Este motor de compresión de 2” se caracteriza por una respuesta en frecuencia muy amplia un rendimiento elevado y un buen comportamiento
en potencia. La utilización de un diafragma de titanio y una bobina de 3” de diámetro le confieren una extraordinaria naturalid ad en la r eproducción
de voz, así como una gran fidelidad en alta frecuencia.
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power Capacity*
Program Power
Sensitivity*
Frequency range
Recommended
crossover
Voice coil diameter
Magnetic assembly weight
Flux density
BL factor
49 mm. 2 in.
8 ohms.
8 ohms @ 6 kHz
5.5 ohm
80 w RMS above 1 kHz
160 Watts. above 1 kHz
110 dB 1w @ 1m
coupled to TD-460 horn
0.6 - 18 kHz
800 Hz or higher
72.2 mm. 2.87 in.
6.5 kg. 14.33lb.
1.875 T
10 N/A
MOUNTING INFORMATION
200 mm. 7.87 in.
75 mm. 2.95 in.
Four M6 threaded holes, 90° apart
on 101.6 mm (4 in.) diameter circle.
Mounting hardware is supplied.
7 kg. 15.43 Ib.
7.25 kg. 16 Ib.
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Titanium
Edgewound alum. ribbon
Kapton
Ferrite
-Pro-
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD460/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD400/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD590 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD460/N Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD400/N Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD590 Horn
- 34 -
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
This 1” prof essional high quality compression driver features a compact, lightweight neodymium rare-earth magnet system, an integrated polyester
diaphragm attached to an edgew ound aluminium ribbon wire voice coil, providing exceptionall y acoustic pr essure ov er an extr emel y wide fr ecuency
range, with smooth and flat response, and low harmonic distortion. The coil diaphragm assembly is easily field replaceable without soldering.
Este motor de compresion para altas frecuencias de 1” de salida presenta un compacto y ligero sistema magnético a base de imán de nedoimio,
un diafragma de polyester y bobina de aluminio de hilo plano puesta de canto”. Este motor suministra una excepcional presión acustica sobre
una amplia repuesta de frecuencia, aportando además una muy baja distorsión armómica.
-Pro-
CP385/Nd
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity
Program Power
Sensitivity
Frequency range
Recommended crossover
Voice coil diameter
Magnetic assembly weight
Flux density
Bl factor
25 mm-1 in.
8 ohms
5.2 ohms @ 4.5 kHz
4.7 ohms
50 w RMS above 1.5 kHz
100 w above 1.5 kHz
107 dB 1w @ 1 m
coupled to TD 250 horn
0.8 - 20 kHz
1.2 kHz or higher
44.4 mm. 1.75 in.
1.1 kg. 2.42 lb.
2.2 T
7.5 N/A
MOUNTING INFORMATION
100 mm. - 4 in.
80 mm. 3.1 in.
Three M-5 threaded holes, 120º apart
on 57 mm. (2.24 in.) diameter circle.
Two M5 threaded holes, 180 º apart
on 76.2 mm. (3 in) diameter circle.
1.35 kg. 2.97 lb
1.5 kg. 3.3 lb
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Polyester
Edgewound alum. ribbon
Kapton
Neodymium
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD245 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD235 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD250 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD245 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD235 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD250 Horn
- 35 -
80
Ø100
76,2
25
M-5
57
90º
30º
-Pro-
- 36 -
NOTES
*The power capacity corresponds to the RMS maximum value that can
dissipate the loudspeaker when a sinus signal is applied for a period
of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
CP380M
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power Capacity*
Program Power
Sensitivity*
Frequency range
Recommended
crossover
Voice coil diameter
Magnetic assembly weight
Flux density
BL factor
25 mm. 1 in.
8 ohms.
5.2 ohms @ 4.5 kHz
4.7 ohm
50 w RMS above 1.5 kHz
100 Watts. above 1.5 kHz
107 dB 1w @ 1m
coupled to TD-250 horn
0.8 - 20 kHz
1.2 kHz or higher
44.4 mm. 1.75 in.
3 kg. 6.6lb.
2 T
7 N/A
MOUNTING INFORMATION
146.5 mm. 5.77 in.
75 mm. 2.95 in.
Three M5 threaded holes, 120° apart
on 57 mm (2.24 in.) diameter circle.
Two M5 threaded holes, 180° apart
on 76.2 mm. (3 in.) diameter circle.
Mounting hardware is supplied.
3.25 kg. 7.16 Ib.
3.4 kg. 7.5 Ib.
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Polyester
Edgewound alum. ribbon
Kapton
Ferrite
This 1” professional high quality compression driver features a lightweight diaphragm assembly made with temperature polyester, attached to an
edgewound aluminium ribbon voice coil, providing exceptionally acoustic pressure over an extremely wide frequency range, with smooth and flat
response and low harmonic distortion. The coil diaphragm assembly is easily field replaceable without soldering.
Este modelo de compresión de 1” de salida incorpora un diafragma ultra ligero de poliester, unido a una bobina de hilo plano de aluminio, lo que
le dota de una extraordinaria sensibilidad y amplísima banda pasante. Su gran linealidad le permite ser utilizado con bocinas de directividad constante
sin ningún tipo de ecualización.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD245 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD235 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD250 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD245 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD235 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD250 Horn
-Pro-
- 37 -
CP350/Ti
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Throat diameter
Rated impedance
Minimum impedance
D.C. Resistance
Power Capacity*
Program Power
Sensitivity*
Frequency range
Recommended
crossover
Voice coil diameter
Magnetic assembly weight
Flux density
BL factor
25 mm. 1 in.
8 ohms.
5 ohms @ 5 kHz
6.8 ohm
50 w RMS above 1.5 kHz
100 Watts. above 1.5 kHz
104 dB 1w @ 1m
coupled to TD-250 horn
0.8 - 20 kHz
1 kHz or higher, 12 dB/oct. min.
44.4 mm. 1.75 in.
3.06 kg. 6.7lb.
1.9 T
9.6 N/A
MOUNTING INFORMATION
140 mm. 5.5 in.
65 mm. 2.55 in.
Three M5 threaded holes, 120° apart.
on 57 mm (2.24 in.) diameter circle
Two M5 threaded holes, 180° apart.
on 76.2 mm. (3 in.) diameter circle.
Mounting hardware is supplied
3.28 kg. 7.2 Ib.
3.4 kg. 4.48 Ib.
Overall diameter
Depth
Mounting
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Titanium
Edgewound alum. ribbon
Kapton
Ferrite
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada. Por potencia programa se
entiende la capacidad de altavoz en el manejo de señales transitorias
como sería el proporcionado por el contenido de un pasaje musical
normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
This 1” compression driver features an integral dome and suspension formed from pure titanium, attached to an edgewound aluminium ribbon
voice coil, providing exceptional high acoustic pressure with low distortion and extended response, with extra power handling. The coil diaphragm
assembly is easily field replaceable without soldering.
Motor de compresión de 1” con diafragma de titanio. La extraordinaria resistencia mecánica de este material, así como su gran ligereza hacen
que este transductor se comporte de forma inmejorable desde las frecuencias audibles más altas hasta frecuencias tan bajas como 1000 Hz sin
merma de prestaciones.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD245 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD235 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD250 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD245 Horn
FREE AIR IMPEDANCE CURVE
Coupling to TD235 Horn
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Coupling to TD250 Horn
-Pro-
- 38 -
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
CP25
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
8.5 ohms @ 9 kHz
6.1 ohm
25 w RMS
50 Watts.
104 dB 1w @ 1m.
2.5 - 20 kHz
5 kHz or higher
100° x 60°
37.6 mm. 1.5 in.
1.45 kg. 3.2 Ib.
1.75 T
6 N/A
MOUNTING INFORMATION
160 x 135 mm. 6.3 x 5.3 in.
125 mm. 4.9 in.
120 x 130 mm. 4.72 x 5.12 in.
1.7 kg. 3.75 Ib.
1.84 kg. 4.05 Ib.
Overall diameter
Depth
Baffle cutout
dimensions
Bolt circle diameter
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Edgewound alum. ribbon
Kapton
Ferrite
This compression tw eeter is designed f or use in m ulti-element loudspeaker systems in both sound reinforcement and studio applications. It features
smooth response with wide controlled dispersion and high output. The voice coil is wound from flat aluminium wire, bonded to an aluminium
diaphragm for extended response and excellent transient attack. The diaphragm assembly is field replaceable without soldering.
Tweeter de compresión de gran potencia con diagrama de dispersión constante para aplicaciones que requieran un control pr eciso de la respuesta
tanto en el eje como fuera del mismo. Dotado de un diafragma y de un bobinado de aluminio movidos por un sistema magnético muy potente,
supera con creces en calidad, rendimiento y potencia, a la mayoría de los reproductores de agudos presentes en el mercado.
HORIZONTAL POLAR PATTERN
FREQUENCY RESPONSE PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
-Pro-
- 39 -
CP22
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
8.5 ohms @ 9 kHz
6.1 ohm
25 w RMS
50 Watts.
107 dB 1w @ 1m.
4 - 20 kHz
5 kHz or higher
40°conical
37.6 mm. 1.5 in.
1.2 kg. 2.64 Ib.
1.55 T
5.2 N/A
MOUNTING INFORMATION
102 x 102 mm. 4 x 4 in.
71 mm. 2.79 in.
ø 92 mm. 3.62 in.
107 mm. 4.21 in.
1.6 kg. 3.5 Ib.
1.67 kg. 3.67 Ib.
Overall diameter
Depth
Baffle cutout dimensions
Bolt circle diameter
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Edgewound alum. ribbon
Kapton
Ferrite
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
This compression tweeter is designed for use in multi-element loudspeaker systems in sound reinforcement applications that require high output,
narrow controlled dispersion and long throw. This model produces a very high output level with flat response and excellent transient attack. This
unit features an aluminium voice coil diaphragm assembly, which is field replaceable without soldering.
Tweeter de compresión para aplicaciones de gran alcance. Su ajustada directividad así como su rendimiento excepcional e importante potencia
admisible le hacen imprescindible en aquellas aplicaciones que precisen de una presión elevada en alta frecuencia a grandes distancias.
FREQUENCY RESPONSE PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
POLAR PATTERN
-Pro-
- 40 -
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
CP21/F
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
8 ohms @ 9 kHz
6.1 ohm
25 w RMS
50 Watts.
105 dB 1w @ 1m.
3.5 - 20 kHz
5 kHz or higher
140° x 40°
37.6 mm. 1.5 in.
1.2 kg. 2.64 Ib.
1.55 T
5.2 N/A
MOUNTING INFORMATION
102 x 102 mm. 4 x 4 in.
72 mm. 2.83 in.
ø 92 mm. 3.62 in.
107 mm. 4.21 in.
1.7 kg. 3.75 Ib.
1.75 kg. 3.85 Ib.
Overall diameter
Depth
Baffle cutout dimensions
Bolt circle diameter
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Edgewound alum. ribbon
Kapton
Ferrite
This compression tw eeter is designed f or use in m ulti-element loudspeaker systems in both sound reinforcement and studio applications. It features
smooth response with wide controlled dispersion in the horizontal plane (140°). The voice coil is wound from flat aluminium wire, bonded to an
aluminium diaphragm for extended response and excellent transient attack. The diaphragm assembly is field replaceable without soldering.
Modelo similar al CP22, pero con una dispersión horizontal muy amplia. Especialmente recomendado para aplicaciones que precisen de una gran
definición en alta frecuencia, pero que además requieran una cobertura horizontal importante.
HORIZONTAL POLAR PATTERN
FREQUENCY RESPONSE PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
-Pro-
- 41 -
CP16
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
8.5 ohms @ 10 kHz
7.3 ohm
15 w RMS
30 Watts.
105 dB 1w @ 1m.
3 - 20 kHz
6 kHz or higher
40° conical
25.8 mm. 1 in.
0.66 kg. 1.45 Ib.
1.45 T
4 N/A
MOUNTING INFORMATION
86 x 86 mm. 3.38 x 3.38 in.
65 mm. 2.56 in.
ø 75 mm. 2.95 in.
92 mm. 3.62 in.
0.76 kg. 1.67 Ib.
0.8 kg. 1.76 Ib.
Overall diameter
Depth
Baffle cutout dimensions
Bolt circle diameter
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Copper
Kapton
Ferrite
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
This compression tw eeter is designed f or using in m ulti-element loudspeaker systems in sound reinf orcement applications that r equir e high output,
narrow controlled dispersion and long throw. This model produces a very high output level with flat response and excellent transient attack. This
unit features an aluminium voice coil diaphragm assembly, which is field replaceable without soldering.
Tweeter de compresión de pequeño tamaño, pero de grandes prestaciones. Se caracteriza por una directividad pronunciada, para aplicaciones en
exteriores que precisen de un buen nivel de presión acústica en alta frecuencia.
POLAR PATTERN
FREQUENCY RESPONSE PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
-Pro-
- 42 -
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
CP12/N
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
8 ohms @ 8 kHz
5 ohm
15 w RMS
30 Watts.
107 dB 1w @ 1m.
3 - 20 kHz
6 kHz, 12 dB/oct. min.
40° conical
25.8 mm. 1 in.
0.7 kg. 1.54 Ib.
1.4 T
4 N/A
MOUNTING INFORMATION
87 x 87 mm. 3.4 x 3.4 in.
72 mm. 2.83 in.
ø 74 mm. 2.9 in.
91 mm. 3.58 in.
0.75 kg. 1.65 Ib.
0.85 kg. 1.87 Ib.
Overall diameter
Depth
Baffle cutout dimensions
Bolt circle diameter
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Edgewound alum. ribbon
Nomex
Ferrite
The model CP 12/N is a professional lightweight compression tweeter, featuring an aluminium voice coil-diaphragm assembly. This device has a
smooth response in all its frequency ranges with an incredibly high sound pressure (107 dB), as well as a narrow controlled dispersion for long
throw applications. This models is well suited for use in two or three-way compact size enclosures.
The diaphragm assembly is field replaceable without soldering.
Modelo similar al CP16, pero con una eficiencia mayor gracias a la utilización de una bobina de hilo plano de aluminio y a un optimizado diseño.
Su aplicación principal es en instalaciones de exteriores, pero puede ser utilizado con m ucho éxito en sistemas semiprofesionales y de alta fidelidad.
POLAR PATTERN
FREQUENCY RESPONSE, PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
-Pro-
- 43 -
CP09
HIGH FREQUENCY
COMPRESSION
DRIVER
SPECIFICATIONS
Rated impedance
Minimum impedance
D.C. Resistance
Power capacity*
Program Power
Sensitivity**
Frequency range
Recommended crossover
Dispersion H x V
Voice coil diameter
Magnetic assembly weight
Flux density
BL Factor
8 ohms.
7.5 ohms @ 8 kHz
5 ohm
15 w RMS
30 Watts.
104 dB 1w @ 1m.
2 - 20 kHz
6 kHz, 12 dB/oct. min.
90° x 60° conical
25.8 mm. 1 in.
0.7 kg. 1.54 Ib.
1.4 T
4 N/A
MOUNTING INFORMATION
98 x 92 mm. 3.85 x 3.6 in.
96 mm. 3.78 in.
90x70 mm. 3.54x2.75 in.
0.75 kg. 1.65 Ib.
0.85 kg. 1.87 Ib.
Overall dimensions
Depth
Baffle cutout dimensions
Net weight
Shipping weight
MATERIALS
Diaphragm
Voice coil
Voice coil former
Magnet
Aluminium
Edgewound alum. ribbon
Nomex
Ferrite
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at lest two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
**Sensitivity was measured at 1m distance, on axis, with 1w input,
averaged in the range 3-15 kHz.
NOTAS
* La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal determinada. Por potencia programa se entiende la
capacidad de altavoz en el manejo de señales transitorias como sería
el proporcionado por el contenido de un pasaje musical normal.
**Medición realizada con el micrófono a 1 m de distancia, en el eje,
aplicando 1w al altavoz, promediando en el rango 1-7 kHz.
This compression tweeter is a professional lightweight, featuring an aluminium voice coil-diaphragm assembly and constant directivity horn. The
voice coil is wound from flat aluminium wir e, bonded to an aluminium diaphragm for extended response and excellent transient attack. This device
has a wide controlled dispersion in the horizontal and vertical axes (90° x 60°), and a smooth response in all its frequency ranges with an incredibly
high sound pressure. The diaphragm assembly is field replaceable without soldering.
Este tweeter de compresión, dotado de un diafragma y un bobinado de aluminio y cargado por una bocina de directividad constante, proporciona
una cobertura angular muy amplia y una respuesta transitoria excelente con una sensibilidad elevada y una potencia admisible importante a pesar
de su pequeño tamaño.
HORIZONTAL POLAR PATTERN
FREQUENCY RESPONSE PHASE. On axis, 1w @ 1m.
TIME RESPONSE, MAGN.
FREE AIR IMPEDANCE CURVE
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
