Product Folder Sample & Buy Technical Documents Support & Community Tools & Software LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 LM2907 and LM2917 Frequency to Voltage Converter 1 Features 3 Description * The LM2907 and LM2917 devices are monolithic frequency-to-voltage converters with a high gain op amp designed to operate a relay, lamp, or other load when the input frequency reaches or exceeds a selected rate. The tachometer uses a charge pump technique and offers frequency doubling for lowripple, full-input protection in two versions (8-pin LM2907 and LM2917), and its output swings to ground for a zero frequency input. 1 * * * * * * * * * Ground Referenced Tachometer Input Interfaces Directly With Variable Reluctance Magnetic Pickups Op Amp Has Floating Transistor Output 50-mA Sink or Source to Operate Relays, Solenoids, Meters, or LEDs Frequency Doubling For Low Ripple Tachometer Has Built-In Hysteresis With Either Differential Input or Ground Referenced Input 0.3% Linearity (Typical) Ground-Referenced Tachometer is Fully Protected From Damage Due to Swings Above VCC and Below Ground Output Swings to Ground For Zero Frequency Input Easy to Use; VOUT = fIN x VCC x R1 x C1 Zener Regulator on Chip allows Accurate and Stable Frequency to Voltage or Current Conversion (LM2917) The two basic configurations offered include an 8-pin device with a ground-referenced tachometer input and an internal connection between the tachometer output and the op amp noninverting input. This version is well suited for single speed or frequency switching or fully buffered frequency-to-voltage conversion applications. Device Information(1) 2 Applications * * * * * * * * * * * The op amp is fully compatible with the tachometer and has a floating transistor as its output. This feature allows either a ground or supply referred load of up to 50 mA. The collector may be taken above VCC up to a maximum VCE of 28 V. PART NUMBER Over- and Under-Speed Sensing Frequency-to-Voltage Conversion (Tachometer) Speedometers Breaker Point Dwell Meters Hand-Held Tachometers Speed Governors Cruise Control Automotive Door Lock Control Clutch Control Horn Control Touch or Sound Switches LM2907-N, LM2917-N PACKAGE BODY SIZE (NOM) PDIP (8) 6.35 mm x 9.81 mm PDIP (14) 6.35 mm x 19.177 mm SOIC (8) 3.91 mm x 4.90 mm SOIC (14) 3.91 mm x 8.65 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Minimum Component Tachometer Diagram 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 9 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Description (continued)......................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 5 7.1 7.2 7.3 7.4 7.5 7.6 5 5 5 6 6 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Parameter Measurement Information .................. 9 Detailed Description ............................................ 10 9.1 Overview ................................................................. 10 9.2 Functional Block Diagram ....................................... 11 9.3 Feature Description................................................. 11 9.4 Device Functional Modes........................................ 12 10 Application and Implementation........................ 13 10.1 Application Information.......................................... 13 10.2 Typical Applications .............................................. 14 11 Power Supply Recommendations ..................... 27 12 Layout................................................................... 28 12.1 Layout Guidelines ................................................. 28 12.2 Layout Example .................................................... 28 13 Device and Documentation Support ................. 29 13.1 13.2 13.3 13.4 13.5 13.6 Related Links ........................................................ Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 29 29 29 29 29 29 14 Mechanical, Packaging, and Orderable Information ........................................................... 29 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (March 2013) to Revision D Page * Added Device Information table, Pin Configuration and Functions section, ESD Ratings table, Recommended Operating Conditions table, Thermal Information table, Parameter Measurement Information section, Detailed Description section, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ...... 1 * Deleted Built-In Zener on LM2917 from Features .................................................................................................................. 1 * Deleted Only One RC Network Provides Frequency Doubling from Features....................................................................... 1 * Added Thermal Information table ........................................................................................................................................... 6 * Changed tablenote text From: C2 = 0.22 mFd To: C2 = 0.22 F .......................................................................................... 6 Changes from Revision B (March 2013) to Revision C * 2 Page Changed layout of National Semiconductor Data Sheet to TI format .................................................................................... 1 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 5 Description (continued) The more versatile configurations provide differential tachometer input and uncommitted op amp inputs. With this version the tachometer input may be floated and the op amp becomes suitable for active filter conditioning of the tachometer output. Both of these configurations are available with an active shunt regulator connected across the power leads. The regulator clamps the supply such that stable frequency-to-voltage and frequency-to-current operations are possible with any supply voltage and a suitable resistor. 6 Pin Configuration and Functions P and D Package 8-Pin PDIP and SOIC Top View TACH+ 1 8 TACH/GND CP1 2 7 IN CP2/IN+ 3 6 V+ EMIT 4 5 COL Not to scale Pin Functions: 8 Pins PIN NAME NO. I/O DESCRIPTION COL 5 I The collector of the bipolar junction transistor CP1 2 O A capacitor placed on this pin will be charged up to VCC/2 by a constant current source of 180 A typical at the start of every positive half cycle. At the beginning of negative half cycles this capacitor is discharged the same amount at the same rate. CP2/IN+ 3 I/O See pins CP1 and IN+. On 8-pin devices (8-pin LM2907 and LM2917) these two nodes share a pin and are internally connected. EMIT 4 O The emitter of the bipolar junction transistor GND -- G Ground IN+ -- I The noninverting input to the high gain op amp IN- 7 I The inverting input to the high gain op amp NC -- -- TACH+ 1 I Positive terminal for the input signal that leads to the noninverting terminal of the internal SchmittTrigger comparator. TACH-/GND 8 I Negative terminal for the input signal that leads to the noninverting terminal of the internal SchmittTrigger comparator. (NOTE: On 8-pin devices, LM2907 and LM2917, this pin is internally connected to ground and must be tied to ground externally to provide the reference voltage of the device). V+ 6 I Supply voltage No connect Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 3 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com NFF and D Package 14-Pin PDIP and SOIC Top View TACH+ 1 14 NC CP1 2 13 NC CP2 3 12 GND IN+ 4 11 TACH EMIT 5 10 IN NC 6 9 V+ NC 7 8 COL Not to scale Pin Functions: 14 Pins PIN NAME NO. I/O DESCRIPTION COL 8 I The collector of the bipolar junction transistor CP1 2 O A capacitor placed on this pin will be charged up to VCC/2 by a constant current source of 180 A typical at the start of every positive half cycle. At the beginning of negative half cycles this capacitor is discharged the same amount at the same rate. CP2 3 O The charge pump sources current out of this pin equal to the absolute value of the capacitor current on CP1. A resistor and capacitor in parallel connected to this pin filters the current pulses into the output voltage. EMIT 5 O The emitter of the bipolar junction transistor GND 12 G Ground IN+ 4 I The noninverting input to the high gain op amp IN- 10 I The inverting input to the high gain op amp NC 6, 7, 13, 14 -- TACH+ 1 I Positive terminal for the input signal that leads to the noninverting terminal of the internal SchmittTrigger comparator. TACH- 11 I Negative terminal for the input signal that leads to the noninverting terminal of the internal SchmittTrigger comparator. V+ 9 I Supply voltage 4 No connect Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) MAX UNIT Supply voltage MIN 28 V Supply current (Zener options) 25 mA Collector voltage 28 V 28 V Differential input voltage Input voltage Tachometer, op amp, and comparator Tachometer LM2907 (8), LM2917 (8) LM2907 (14), LM2917 (14) Op amp and comparator Power dissipation 28 0 28 0 28 LM29x7 (8) 1200 LM29x7 (14) 1580 PDIP package Soldering information -28 SOIC package Soldering (10 s) 260 Vapor phase (60 s) 215 Infrared (15 s) V mW C 220 Operating temperature, TJ -40 85 C Storage temperature, Tstg -65 150 C (1) (2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. 7.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JESD22-A114 (1) 1000 Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) 250 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 7.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN LM2907 (8), LM2917 (8) Input voltage LM2907 (14), LM2917 (14) Output sink current Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N NOM MAX UNIT -28 28 0 28 V 50 mA Submit Documentation Feedback V 5 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 7.4 Thermal Information LM2907, LM2917 THERMAL METRIC (1) P (PDIP) D (SOIC) NFF (PDIP) D (SOIC) 8 PINS 8 PINS 14 PINS 14 PINS UNIT RJA Junction-to-ambient thermal resistance 77.6 110 69.1 83.7 C/W RJC(top) Junction-to-case (top) thermal resistance 80.5 53.9 64.8 42.1 C/W RJB Junction-to-board thermal resistance 54.8 50.4 49.1 38 C/W JT Junction-to-top characterization parameter 37.6 9.1 35.1 7.7 C/W JB Junction-to-board characterization parameter 54.8 49.9 49 37.7 C/W RJC(bot) Junction-to-case (bottom) thermal resistance -- -- -- -- C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. 7.5 Electrical Characteristics VCC = 12 VDC, TA = 25C, see test circuit PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 10 25 40 mV TACHOMETER Input thresholds VIN = 250 mVp-p at 1 kHz (1) Hysteresis VIN = 250 mVp-p at 1 kHz (1) 30 VIN = 250 mVp-p at 1 kHz (1) 3.5 10 5 15 1 LM29x7 offset voltage VIN = 250 mVp-p at 1 kHz (8-pin LM29x7) (1) Input bias current VIN = 50 mVDC 0.1 VOH High level output voltage For CP1, VIN = 125 mVDC (2) 8.3 VOL Low level output voltage For CP1, VIN = -125 mVDC (2) 2.3 I2, I3 Output current V2 = V3 = 6 V (3) I3 Leakage current I2 = 0, V3 = 0 K Gain constant See (2) Linearity fIN = 1 kHz, 5 kHz, or 10 kHz (4) mV mV A V V 140 180 240 A 0.9 1 0.1 1.1 A -1% 0.3% 1% OP AMP AND COMPARATOR VOS Input offset voltage VIN = 6 V 3 10 mV IBIAS Bias current VIN = 6 V 50 500 nA Input common-mode voltage 0 Voltage gain V/mV 50 mA VC = 1 Output source current VE = VCC -2 10 ISINK = 5 mA 0.1 ISINK = 20 mA ISINK = 50 mA V 200 Output sink current Saturation voltage 40 VCC-1.5 1 mA 0.5 V 1 V 1.5 V ZENER REGULATOR Regulator voltage RDROP = 470 7.56 Series resistance 10.5 Temperature stability (3) (4) 6 15 1 Total supply current (1) (2) V 3.8 mV/C 6 mA Hysteresis is the sum VTH - (-VTH), offset voltage is their difference. See test circuit. VOH = 0.75 x VCC - 1 VBE and VOL = 0.25 x VCC - 1 VBE, therefore VOH - VOL = VCC / 2. The difference (VOH - VOL) and the mirror gain (I2 / I3) are the two factors that cause the tachometer gain constant to vary from 1. Ensure that when choosing the time constant R1 x C1 that the maximum anticipated output voltage at CP2/IN+ can be reached with I3 x R1. The maximum value for R1 is limited by the output resistance of CP2/IN+ which is greater than 10 M typically. Nonlinearity is defined as the deviation of VOUT (at CP2/IN+) for fIN = 5 kHz from a straight line defined by the VOUT at 1 kHz and VOUT at 10 kHz. C1 = 1000 pF, R1 = 68 k and C2 = 0.22 F. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 7.6 Typical Characteristics Figure 1. Tachometer Linearity vs Temperature Figure 2. Tachometer Linearity vs Temperature Figure 3. Total Supply Current Figure 4. Zener Voltage vs Temperature Figure 5. Normalized Tachometer Output (K) vs Temperature Figure 6. Normalized Tachometer Output (K) vs Temperature Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 7 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Typical Characteristics (continued) 8 Figure 7. Tachometer Currents I2and I3 vs Supply Voltage Figure 8. Tachometer Currents I2and I3 vs Temperature Figure 9. Tachometer Linearity vs R1 Figure 10. Tachometer Input Hysteresis vs Temperature Figure 11. Op Amp Output Transistor Characteristics Figure 12. Op Amp Output Transistor Characteristics Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 8 Parameter Measurement Information Figure 13. Test Circuit Figure 14. Tachometer Input Threshold Measurement Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 9 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 9 Detailed Description 9.1 Overview The LM29x7 frequency-to-voltage converter features two separate inputs to monitor the signal. In the 8-pin devices, one of these inputs is internally grounded and therefore it monitors the remaining input for zero crossings. In the 14-pin devices, both of these inputs are open and it instead detects whenever the differential voltage switches polarity. Therefore, the input comparator outputs a square wave of equal frequency to the input. A charge pump system is used to translate the frequency of this square wave to a voltage. At the start of every positive half cycle of the input signal a 180-A constant current charges C1 until its voltage has increased by VCC/2. The capacitor is held at that voltage until the input signal begins a negative half cycle. Then the 180-A constant current discharges capacitor C1 until its voltage has dropped by VCC/2. This voltage is held until the next positive half cycle and the process repeats. This generates pulses of current flowing into and out of capacitor C1 at the same frequency as the input signal. For every full cycle, the charge pump mirrors both current pulses as positive current pulses into the parallel combination of resistor R1 and capacitor C2. Therefore every full cycle, the amount of charge leaving pin 3 is equal to the sum of the charge entering C1 and leaving C1. Because the voltage at pin 3 is equal to I3(avg) x R1, I(avg) is calculated in Equation 1. I3(avg) = Q/t = (Qcharge + Qdischarge) / (1 / f) = 2 x Q x f = 2 x C1 x (VCC/2) x f = C1 x VCC x f (1) This average current will be flowing across R1, giving the output voltage in Equation 2. Vo = R1 x C1 x VCC x f (2) C2 acts as a filter to smooth the pulses of current and does not affect the output voltage. However, the size of C2 determines both the output response time for changes in frequency and the amount of output voltage ripple. The voltage generated is then fed in a high gain op amp. This op amp drives a bipolar transistor whose collector and emitter are each broken out to a pin. The LM29x7 has the flexibility to be configured a variety of ways to meet system requirements including voltage output, driving loads, operating a relay, and more. 10 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 9.2 Functional Block Diagram *This connection made on 8-pin LM2907 and LM2917 only. **This connection made on LM2917 and 8-pin LM2917 only. 9.3 Feature Description 9.3.1 Differential Input This device features a Schmitt-Trigger comparator that is the first stage in converting the input signal. Every time the output of the comparator flips between high and low correlates to a half cycle elapsing on the input signal. On the LM29x7-8 devices, one terminal of this comparator is internally connected to ground. This requires that the input signal cross zero volts in order for device to detect the frequency. On the LM29x7 devices, the input terminals to the Schmitt-Trigger comparator are both available for use. This open terminal allows the potential at which the comparator's output is flipped to be applied externally. This allows the device to accept signals with DC offset or compare differential inputs. 9.3.2 Configurable While the ratio of output voltage to input frequency is dependent on supply voltage, it is easily adjusted through the combination of one resistor and one capacitor, R1 and C1. The formula for calculating the expected output voltage is in Equation 3. VOUT = VCC x f x C1 x R1. (3) The sizes of R1 and C1 have other effects on the system such as maximum frequency and output linearity. See Choosing R1 and C1 for detailed instructions on sizing components. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 11 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Feature Description (continued) 9.3.3 Output Stage The output voltage generated by the charge pump is fed in the noninverting terminal of a high gain op amp. This op amp then drives and uncommitted bipolar junction transistor. This allows the LM2907 to be configured a variety of ways to meet system needs. The output voltage can be buffered and used to drive a load (see Figure 15) or an output threshold can be given to trigger a load switch (see Figure 18). 9.4 Device Functional Modes 9.4.1 Grounded Input Devices (8-Pin LM2907 and LM2917) These devices have one of the two Schmitt-Trigger comparator inputs internally grounded and must be externally connected to the system ground as well. This configuration monitors the remaining terminal for zero crossings. 9.4.2 Differential Input Devices (LM2907 and LM2917) These devices have both inputs to the Schmitt-Trigger comparator available and broken out to pins 1 and 11. This configuration allows a new switching threshold provided in the case of signals with DC offset or to intake a differential pair and switch based on voltage difference. 12 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 10 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 10.1 Application Information The LM2907 series of tachometer circuits is designed for minimum external part count applications and maximum versatility. To fully exploit its features and advantages, first examine its theory of operation. The first stage of operation is a differential amplifier driving a positive feedback flip-flop circuit. The input threshold voltage is the amount of differential input voltage at which the output of this stage changes state. Two options (8-pin LM2907 and LM2917) have one input internally grounded so that an input signal must swing above and below ground and exceed the input thresholds to produce an output. This is offered specifically for magnetic variable reluctance pickups which typically provide a single-ended AC output. This single input is also fully protected against voltage swings to 28 V, which are easily attained with these types of pickups. The differential input options (LM2907, LM2917) give the user the option of setting his own input switching level and still have the hysteresis around that level for excellent noise rejection in any application. Of course to allow the inputs to attain common-mode voltages above ground, input protection is removed and neither input should be taken outside the limits of the supply voltage being used. It is very important that an input not go below ground without some resistance in its lead to limit the current that will then flow in the epi-substrate diode. Following the input stage is the charge pump where the input frequency is converted to a DC voltage. To do this requires one timing capacitor, one output resistor, and an integrating or filter capacitor. When the input stage changes state (due to a suitable zero crossing or differential voltage on the input) the timing capacitor is either charged or discharged linearly between two voltages whose difference is VCC/2. Then in one half cycle of the input frequency or a time equal to 1/2 fIN the change in charge on the timing capacitor is equal to VCC/2 x C1. The average amount of current pumped into or out of the capacitor is shown in Equation 4. V 'Q = ic(AVG) = C1x CC x (2 fIN ) = VCC x fINx C1 (4) T 2 The output circuit mirrors this current very accurately into the load resistor R1, connected to ground, such that if the pulses of current are integrated with a filter capacitor, then VO = ic x R1, and the total conversion formula becomes Equation 5. VO = VCC x fIN x C1 x R1 x K where * K is the gain constant (typically 1) (5) The size of C2 is dependent only on the amount of ripple voltage allowable and the required response time. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 13 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 10.2 Typical Applications 10.2.1 Minimum Component Tachometer Figure 15. Minimum Component Tachometer Diagram 10.2.1.1 Design Requirements * C1: This capacitor is charged and discharged every cycle by a 180-A typical current source. Smaller capacitors can be charged quicker therefore increasing the maximum readable frequency. However, lower capacitors values reduce the output voltage produced for a given frequency. C1 must not be sized lower than 500-pF die to its role in internal compensation. * R1: This resistor produces the output voltage from current pulses source by the internal charge pump. Higher values increase the output voltage for a given frequency, but too large will degrade the output's linearity. Because the current pulses are a fixed magnitude of 180 A typical, R1 must be big enough to produce the maximum desired output voltage at maximum input frequency. At maximum input frequency the pulse train duty cycle is 100%, therefore the average current is 180 A and R1 = Vo(max) / 180 A. * C2: This capacitor filters the ripple produced by the current pulses sourced by the charge pump. Large values reduce the output voltage ripple but increase the output's response time to changes in input frequency. * Rload: The load resistance must be large enough that at maximum output voltage, the current is under the rated value of 50 mA. 10.2.1.2 Detailed Design Procedure 10.2.1.2.1 Choosing R1 and C1 There are some limitations on the choice of R1 and C1 which should be considered for optimum performance. The timing capacitor also provides internal compensation for the charge pump and must be kept larger than 500 pF for very accurate operation. Smaller values can cause an error current on R1, especially at low temperatures. Several considerations must be met when choosing R1. The output current at pin 3 is internally fixed and therefore VO/R1 must be less than or equal to this value. If R1 is too large, it can become a significant fraction of the output impedance at pin 3 which degrades linearity. Also output ripple voltage must be considered and the size of C2 is affected by R1. An expression that describes the ripple content on pin 3 for a single R1C2 combination is in Equation 6. V VCC x fIN x C1 * C1 VRIPPLE = CC x x 1 pk- pk 2 C2 (c) I2 (6) R1 can be chosen independent of ripple. However, response time, or the time it takes VOUT to stabilize at a new voltage, increases as the size of C2 increases, so a compromise between ripple, response time, and linearity must be chosen carefully. As a final consideration, the maximum attainable input frequency is determined by VCC, C1, and I2 in Equation 7. 14 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 Typical Applications (continued) fMAX = I2 C1x VCC (7) 10.2.1.2.2 Using Zener Regulated Options (LM2917) For those applications where an output voltage or current must be obtained independent of supply voltage variations, the LM2917 is offered. The most important consideration in choosing a dropping resistor from the unregulated supply to the device is that the tachometer and op amp circuitry alone require about 3 mA at the voltage level provided by the Zener. At low supply voltages there must be some current flowing in the resistor above the 3-mA circuit current to operate the regulator. As an example, if the raw supply varies from 9 V to 16 V, a resistance of 470 minimizes the Zener voltage variation to 160 mV. If the resistance goes under 400 or over 600 , the Zener variation quickly rises above 200 mV for the same input variation. 10.2.1.3 Application Curves C1 = .01 F Rdrop = 910 C2 = 1 F R1 = 100 k Zener Regulated VCC = 7.58 V C1 = .01 F Rdrop = 910 Figure 16. Output Response to an Increase in Input Frequency C2 = 1 F R1 = 100 k Zener Regulated VCC = 7.58 V Figure 17. Output Voltage Ripple 10.2.2 Other Application Circuits This section shows application circuit examples using the LM2907-N and LM2917-N devices. Customers must fully validate and test these circuits before implementing a design based on these examples. SPACER Load is energized when fIN (1 / ( 2 x RC)) Figure 18. Speed Switch Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 15 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Typical Applications (continued) Figure 19. Zener Regulated Frequency to Voltage Converter SPACER Figure 20. Breaker Point Dwell Meter SPACER 16 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 Typical Applications (continued) VO = 6 V at 400 Hz or 6000 ERPM (8 Cylinder Engine) Figure 21. Voltage Driven Meter Indicating Engine RPM SPACER IO = 10 mA at 300 Hz or 6000 ERPM (6 Cylinder Engine) Figure 22. Current Driven Meter Indicating Engine RPM SPACER Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 17 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Typical Applications (continued) VOUT = 1 V to 10 V for CX = 0.01 to 0.1 mFd and R = 111 k Figure 23. Capacitance Meter SPACER Figure 24. Two-Wire Remote Speed Switch SPACER 18 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 Typical Applications (continued) V3 steps up in voltage by the amount of (VCC x C1) / C2, for each complete input cycle (2 zero crossings). For example: if C2 = 200 x C1 after 100 consecutive input cycles, then V3 = 1/2 x VCC. Figure 25. 100 Cycle Delay Switch SPACER Flashing begins when fIN 100 Hz Flash rate increases with input frequency increase beyond trip point. Figure 26. Flashing LED Indicates Over-Speed SPACER Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 19 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com fPOLE = 0.707 / (2 x x RC) RESPONSE = 2.57 / (2 x x fPOLE) Figure 27. Frequency to Voltage Converter With 2 Pole Butterworth Filter to Reduce Ripple 10.2.2.1 Variable Reluctance Magnetic Pickup Buffer Circuits Precision two-shot output frequency is twice the input frequency Pulse width = (VCC / 2) x (C1 / 12) Pulse height = VZENER Figure 28. Magnetic Pickup Buffer With Zener Regulated Output Magnitude SPACER 20 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 Figure 29. Magnetic Pickup Buffer With 1/2 VCC Output Magnitude 10.2.2.2 Finger Touch or Contact Switch Figure 30. Finger Touch or Contact Switch Diagram SPACER Figure 31. System Output in Response to Consecutive Button Presses Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 21 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 10.2.2.3 Over-Speed Latch Output latches when fIN = (R2 / (R1 + R2)) x (1 / RC). Output is reset by removing VCC. Figure 32. Over-Speed Latch Circuit Diagram SPACER Figure 33. VOUT vs FIN 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 10.2.2.4 Frequency Switch Applications Some frequency switch applications may require hysteresis in the comparator function which can be implemented in several ways. Example circuits are shown in Figure 34 to Figure 36. Figure 34. Frequency Switch With Resistor Divider Threshold SPACER Figure 35. Frequency Switch With Added Hysteresis SPACER Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 23 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com Figure 36. Frequency Switch With Added Hysteresis 10.2.2.4.1 Application Curves Figure 37. VOUT vs V3 Figure 38. VOUT vs V3 10.2.2.5 Anti-Skid Circuits 10.2.2.5.1 Select-Low Circuit Figure 39. Select-Low Circuit Diagram 24 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 SPACER VOUT is proportional to the lower of the two input wheel speeds Figure 40. VOUT vs Wheel Speed 10.2.2.5.2 Select-High Circuit Figure 41. Select-High Circuit Diagram SPACER VOUT is proportional to the higher of the two input wheel speeds Figure 42. VOUT vs Wheel Speed Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 25 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 10.2.2.5.3 Select-Average Circuit Figure 43. Select-Average Circuit Diagram 10.2.2.6 Changing the Output Voltage for an Input Frequency of Zero Figure 44. Tachometer With Adjustable Zero Speed Voltage Output SPACER Figure 45. VOUT vs Frequency Plot Shifted to Produce 1 V at Zero Speed 26 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 10.2.2.7 Changing Tachometer Gain Curve or Clamping the Minimum Output Voltage Figure 46. Tachometer With Output Clamped at Low Speeds SPACER Figure 47. VOUT vs Frequency Plot With Output Clamped at Low Speeds 11 Power Supply Recommendations This family of devices is designed to operate from a supply voltage up to 28 V. For the 8-pin LM2907 and LM2917, devices with a fixed ground reference for TACH-, the tachometer inputs can intake voltages between 28 V. LM2907 and LM2917 devices have both tachometer inputs available at the cost of input protection features. This means neither input should be taken outside of the supply voltage range without additional precautions (see Application Information). Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 27 LM2907-N, LM2917-N SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 www.ti.com 12 Layout 12.1 Layout Guidelines * * * Bypass capacitors must be placed as close as possible to the supply pin. When using a through-hole package, it is acceptable to place the bypass capacitor on the bottom layer. All other components must be placed as close to the device as possible. Use of a ground plane is recommended to provide a low-impedance ground across the circuit. Feedback loops must use short and wide traces. 12.2 Layout Example Figure 48. Layout Recommendation 28 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N LM2907-N, LM2917-N www.ti.com SNAS555D - JUNE 2000 - REVISED DECEMBER 2016 13 Device and Documentation Support 13.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LM2907-N Click here Click here Click here Click here Click here LM2917-N Click here Click here Click here Click here Click here 13.2 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 13.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 13.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 13.5 Electrostatic Discharge Caution This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 13.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 14 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LM2907-N LM2917-N Submit Documentation Feedback 29 PACKAGE OPTION ADDENDUM www.ti.com 10-Feb-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2907M NRND SOIC D 14 55 TBD Call TI Call TI -40 to 85 LM2907M LM2907M-8 NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM29 07M-8 LM2907M-8/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM29 07M-8 LM2907M/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM2907M LM2907MX NRND SOIC D 14 2500 TBD Call TI Call TI -40 to 85 LM2907M LM2907MX-8/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM29 07M-8 LM2907MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM2907M LM2907N-8/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 85 LM 2907N-8 LM2907N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS & no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 85 LM2907N LM2917M-8 NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM29 17M-8 LM2917M-8/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM29 17M-8 LM2917M/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM2917M LM2917MX-8/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM29 17M-8 LM2917MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 85 LM2917M LM2917N-8/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 85 LM 2917N-8 LM2917N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS & no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 85 LM2917N (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 10-Feb-2020 PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing LM2907MX SOIC D LM2907MX-8/NOPB SOIC LM2907MX/NOPB SOIC LM2917MX-8/NOPB LM2917MX/NOPB SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.35 2.3 8.0 16.0 Q1 14 2500 330.0 16.4 6.5 D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2907MX SOIC D 14 2500 367.0 367.0 35.0 LM2907MX-8/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM2907MX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LM2917MX-8/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM2917MX/NOPB SOIC D 14 2500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE D0008A SOIC - 1.75 mm max height SCALE 2.800 SMALL OUTLINE INTEGRATED CIRCUIT C SEATING PLANE .228-.244 TYP [5.80-6.19] A .004 [0.1] C PIN 1 ID AREA 6X .050 [1.27] 8 1 2X .150 [3.81] .189-.197 [4.81-5.00] NOTE 3 4X (0 -15 ) 4 5 B 8X .012-.020 [0.31-0.51] .010 [0.25] C A B .150-.157 [3.81-3.98] NOTE 4 .069 MAX [1.75] .005-.010 TYP [0.13-0.25] 4X (0 -15 ) SEE DETAIL A .010 [0.25] .004-.010 [0.11-0.25] 0 -8 .016-.050 [0.41-1.27] DETAIL A (.041) [1.04] TYPICAL 4214825/C 02/2019 NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 [0.15] per side. 4. This dimension does not include interlead flash. 5. Reference JEDEC registration MS-012, variation AA. www.ti.com EXAMPLE BOARD LAYOUT D0008A SOIC - 1.75 mm max height SMALL OUTLINE INTEGRATED CIRCUIT 8X (.061 ) [1.55] SYMM SEE DETAILS 1 8 8X (.024) [0.6] 6X (.050 ) [1.27] SYMM 5 4 (R.002 ) TYP [0.05] (.213) [5.4] LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:8X METAL SOLDER MASK OPENING EXPOSED METAL .0028 MAX [0.07] ALL AROUND SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL .0028 MIN [0.07] ALL AROUND SOLDER MASK DEFINED NON SOLDER MASK DEFINED SOLDER MASK DETAILS 4214825/C 02/2019 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN D0008A SOIC - 1.75 mm max height SMALL OUTLINE INTEGRATED CIRCUIT 8X (.061 ) [1.55] SYMM 1 8 8X (.024) [0.6] 6X (.050 ) [1.27] SYMM 5 4 (R.002 ) TYP [0.05] (.213) [5.4] SOLDER PASTE EXAMPLE BASED ON .005 INCH [0.125 MM] THICK STENCIL SCALE:8X 4214825/C 02/2019 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com MECHANICAL DATA NFF0014A N0014A N14A (Rev G) www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated