LP3875EMP-3.3/NOPB - Texas Instruments

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

LP387x 1.5-A Fast Ultra-Low-Dropout Linear Regulators

1 Features 3 Description

The LP387x series of fast ultra low-dropout linear

1• Input Voltage Range: 2.5 V to 7 V regulators operate from a 2.5-V to 7-V input supply.

• Ultra Low-Dropout Voltage Wide range of preset output voltage options are

• Low Ground Pin Current available. These ultra low-dropout linear regulators

respond very quickly to step changes in load, which

• Load Regulation of 0.06% makes them suitable for low-voltage microprocessor

• 10-nA Quiescent Current in Shutdown Mode applications. The LP3872 and LP3875 are developed

• Ensured Output Current of 1.5-A DC on a CMOS process which allows low quiescent

current operation independent of output load current.

• Available in DDPAK/TO-263, TO-220, and This CMOS process also allows the LP3872 and

SOT-223 Packages LP3875 to operate under extremely low dropout

• Output Voltage Accuracy ± 1.5% conditions.

• ERROR Flag for Output Status Dropout Voltage: Ultra low-dropout voltage; typically

• Sense Option Improves Load Regulation 38 mV at 150-mA load current and 380 mV at 1.5-A

• Minimum Output Capacitor Requirements load current.

• Overtemperature/Overcurrent Protection Ground Pin Current: Typically 6 mA at 1.5-A load

•−40°C to 125°C Junction Temperature Range current.

Shutdown Mode: Typically 10-nA quiescent current

2 Applications when the SD pin is pulled low.

• Microprocessor Power Supplies ERROR Flag: ERROR flag goes low when the output

• GTL, GTL+, BTL, and SSTL Bus Terminators voltage drops 10% below nominal value (LP3872

• Power Supplies for DSPs only).

• SCSI Terminators SENSE: Sense pin improves regulation at remote

• Post Regulators loads (LP3875 only).

• High Efficiency Linear Regulators Precision Output Voltage: Multiple output voltage

options are available ranging from 1.8 V to 5 V with a

• Battery Chargers specified accuracy of ±1.5% at room temperature,

• Other Battery-Powered Applications and ±3.0% over all conditions (varying line, load, and

space temperature).

space Device Information(1)

space PART NUMBER PACKAGE BODY SIZE (NOM)

space SOT-223 (5) 6.50 mm × 3.56 mm

space LP3872 TO-263 (5) 10.16 mm × 8.42 mm

LP3872 Typical Application Circuit SOT-223 (5) 6.50 mm × 3.56 mm

LP3875 TO-263 (5) 10.16 mm × 8.42 mm

TO-220 (5) 14.986 mm × 10.16 mm

(1) For all available packages, see the orderable addendum at

the end of the datasheet.

LP3875 Typical Application Circuit

*SD and ERROR pins must be pulled high

through a 10-kΩpullup resistor. Connect

the ERROR pin to ground if this function is

not used. See the Shutdown Mode and

ERROR Flag Operation sections.

*SD must be pulled high through a 10-kΩ

pullup resistor. See the Shutdown Mode

section.

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

Table of Contents

7.3 Feature Description................................................... 8

1 Features.................................................................. 17.4 Device Functional Modes.......................................... 9

2 Applications ........................................................... 18 Application and Implementation ........................ 11

3 Description............................................................. 18.1 Application Information............................................ 11

4 Revision History..................................................... 28.2 Typical Application.................................................. 11

5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 16

6 Specifications......................................................... 410 Layout................................................................... 16

6.1 Absolute Maximum Ratings ...................................... 410.1 Layout Guidelines ................................................. 16

6.2 ESD Ratings ............................................................ 410.2 Layout Examples................................................... 17

6.3 Recommended Operating Conditions....................... 411 Device and Documentation Support................. 18

6.4 Thermal Information.................................................. 411.1 Related Links ........................................................ 18

6.5 Electrical Characteristics........................................... 511.2 Trademarks........................................................... 18

6.6 Typical Characteristics.............................................. 611.3 Electrostatic Discharge Caution............................ 18

7 Detailed Description.............................................. 811.4 Glossary................................................................ 18

7.1 Overview................................................................... 812 Mechanical, Packaging, and Orderable

7.2 Functional Block Diagram......................................... 8Information ........................................................... 18

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision G (December 2014) to Revision H Page

• Added Input voltage range as first Feature ........................................................................................................................... 1

• Added "(LP3872 only)" .......................................................................................................................................................... 1

• Added "(LP3875 only)" .......................................................................................................................................................... 1

• Changed all VIN and VOUT pin names to IN and OUT in drawings and text........................................................................ 1

• Changed footnotes to appear under each table .................................................................................................................... 4

• Deleted CDM footnote ........................................................................................................................................................... 4

• Deleted last sentence of Short-Circuit Protection subsection ............................................................................................... 9

Changes from Revision F (April 2013) to Revision G Page

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional

Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device

and Documentation Support section, and Mechanical, Packaging, and Orderable Information section; update

thermal values ....................................................................................................................................................................... 1

Product Folder Links: LP3872 LP3875

1 2 34

SD IN OUT ERROR

/SENSE

GND

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

5 Pin Configuration and Functions

5-Pin TO-220 5-Pin DDPAK/TO-263

NDH Package KTT Package

Top View Top View

5-Pin SOT-223

NDC Package

Top View

Pin Functions

NUMBER I/O DESCRIPTION

LP3872 LP3875

NAME TO-220 TO-220

SOT-223 SOT-223

DDPAK/TO-263 DDPAK/TO-263

SD 1 1 1 1 I Shutdown

IN 2 2 2 2 I Input supply

OUT 4 3 4 3 O Output voltage

ERROR 5 4 — — O Error flag

SENSE — — 5 4 I Remote voltage sense

GND 3 5 3 5 — Ground

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

6 Specifications

6.1 Absolute Maximum Ratings(1)(2)

If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability

and specifications. MIN MAX UNIT

Lead temperature (soldering, 5 sec.) 260 °C

Power dissipation(3) Internally limited

IN pin to GND pin voltage −0.3 7.5 V

Shutdown (SD) pin to GND pin voltage −0.3 7.5 V

OUT pin to GND pin voltage(4),(5) −0.3 6 V

IOUT Short-circuit protected

ERROR pin to GND pin voltage VIN V

SENSE pin to GND pin voltage VOUT V

Storage temperature, Tstg −65 150 °C

(1) Stresses beyond those listed under Absolute Maximum Ratings(1)(2) may cause permanent damage to the device. These are stress

ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under

Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.

(3) Internal thermal shutdown circuitry protects the device from permanent damage.

(4) If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.

(5) The output PMOS structure contains a diode between the IN and OUT pins. This diode is normally reverse biased. This diode will get

forward biased if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically

withstand 200 mA of DC current and 1 A of peak current.

6.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions MIN MAX UNIT

VIN supply voltage (1) 2.5 7 V

Shutdown (SD) voltage −0.3 7 V

Maximum operating current (DC) IOUT 1.5 A

Junction temperature –40 125 °C

(1) The minimum operating value for VIN is equal to either [VOUT(NOM) + VDROPOUT] or 2.5 V, whichever is greater.

6.4 Thermal Information LP3872, LP3875 LP3875

THERMAL METRIC(1) NDC (SOT-223) KTT (TO-263) NDH (TO-220) UNIT

5 PINS 5 PINS 5 PINS

RθJA Junction-to-ambient thermal resistance 65.2 40.3 32

RθJC(top) Junction-to-case (top) thermal resistance 47.2 43.4 43.8

RθJB Junction-to-board thermal resistance 9.9 23.1 18.6 °C/W

ψJT Junction-to-top characterization parameter 3.4 11.5 8.8

ψJB Junction-to-board characterization parameter 9.7 22 18

RθJC(bot) Junction-to-case (bottom) thermal resistance n/a 1 1.2

(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.

Product Folder Links: LP3872 LP3875

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

6.5 Electrical Characteristics

Unless otherwise specified: TJ= 25°C, VIN = VO(NOM) + 1 V, IL= 10 mA, COUT = 10 µF, VSD = 2 V.

PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT

Output voltage tolerance (3) VOUT +1 V ≤VIN ≤7 V, 10 mA ≤IL≤1.5 A –1.5% 0% 1.5%

VOUT VOUT +1 V ≤VIN ≤7 V, 10 mA ≤IL≤1.5 A, –3% 3%

–40°C ≤TJ≤125°C

Output voltage line regulation (3) VOUT + 1 V ≤VIN ≤7 V 0.02%

ΔVOL VOUT + 1 V ≤VIN ≤7 V, –40°C ≤TJ≤125°C 0.06%

Output voltage load regulation (3) 10 mA ≤IL≤1.5 A 0.06%

ΔVO/

ΔIOUT 10 mA ≤IL≤1.5 A, –40°C ≤TJ≤125°C 0.12%

IL= 150 mA 38 50

IL= 150 mA, –40°C ≤TJ≤125°C 60

VIN -Dropout voltage (4) mV

VOUT IL= 1.5 A 380 450

IL= 1.5 A, –40°C ≤TJ≤125°C 550

IL= 150 mA 5 9

IL= 150 mA,–40°C ≤TJ≤125°C 10

Ground pin current in normal

IGND mA

operation mode IL= 1.5 A 6 14

IL= 1.5 A, –40°C ≤TJ≤125°C 15

Ground pin current in shutdown VSD ≤0.3 V 0.01 10 µA

IGND mode –40°C ≤TJ≤85°C 50

IO(PK) Peak output current VOUT ≥VO(NOM) – 4% 1.8 A

SHORT CIRCUIT PROTECTION

ISC Short-circuit current 3.2 A

SHUTDOWN INPUT

Output = High VIN

Output = High, –40°C ≤TJ≤125°C 2

VSDT Shutdown threshold V

Output = Low 0

Output = Low, –40°C ≤TJ≤125°C 0.3

TdOFF Turnoff delay IL= 1.5 A 20 µs

TdON Turnon delay IL= 1.5 A 25 µs

ISD SD input current VSD = VIN 1 nA

ERROR FLAG

Threshold See(5) 10%

VTSee(5), –40°C ≤TJ≤125°C 5% 16%

Threshold hysteresis See(5) 5%

VTH See(5), –40°C ≤TJ≤125°C 2% 8%

ERROR flag saturation Isink = 100 µA 0.02

VEF(Sat) V

Isink = 100 µA, –40°C ≤TJ≤125°C 0.1

Td Flag reset delay 1 µs

Ilk ERROR flag pin leakage current 1 nA

Imax ERROR flag pin sink current VError = 0.5 V 1 mA

(1) Limits are specified by testing, design, or statistical correlation.

(2) Typical numbers are at 25°C and represent the most likely parametric norm.

(3) Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage.

Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line

and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the

output voltage tolerance specification.

(4) Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value.

Dropout voltage specification applies only to output voltages of 2.5 V and above. For output voltages below 2.5 V, the dropout voltage is

nothing but the input to output differential, because the minimum input voltage is 2.5 V.

(5) ERROR Flag threshold and hysteresis are specified as percentage of regulated output voltage. See ERROR Flag Operation.

Product Folder Links: LP3872 LP3875

SHUTDOWN IQ (PA)

TEMPERATURE (oC)

-40 -20 0 20 40 60 80 100 125

0.001

0.01

0.1

ERROR THRESHOLD (% of VOUT)

JUNCTION TEMPERATURE (oC)

-40 -20 0 20 40 60 80 100 125

1.8 2.3 2.8 3.3 3.8 4.3 5.0

OUTPUT VOLTAGE (V)

GROUND PIN CURRENT (mA)

0 0.5 11.5

100

200

300

400

500

600

OUTPUT LOAD CURRENT (A)

DROPOUT VOLTAGE (mV)

25oC

-40oC

125oC

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

Electrical Characteristics (continued)

Unless otherwise specified: TJ= 25°C, VIN = VO(NOM) + 1 V, IL= 10 mA, COUT = 10 µF, VSD = 2 V.

PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT

AC PARAMETERS

VIN = VOUT + 1 V, COUT = 10 µF 73

VOUT = 3.3 V, f = 120 Hz

PSRR Ripple rejection dB

VIN = VOUT + 0.5 V, COUT = 10 µF 57

VOUT = 3.3 V, f = 120 Hz

ρn(l/f) Output noise density f = 120 Hz 0.8 µV

BW = 10 Hz – 100 kHz, VOUT = 2.5 V 150 µV

enOutput noise voltage (rms)

BW = 300 Hz – 300 kH, VOUT = 2.5 V 100

6.6 Typical Characteristics

Unless otherwise specified: TJ= 25°C, COUT = 10 µF, CIN = 10 µF, SD pin is tied to VIN, VOUT = 2.5 V, VIN = VO(NOM) + 1 V, IL=

10 mA

Figure 1. Dropout Voltage vs Output Load Current Figure 2. Ground Current vs Output Voltage

IL= 1.5 A

Figure 4. Errorflag Threshold vs Junction Temperature

Figure 3. Shutdown IQvs Junction Temperature

Product Folder Links: LP3872 LP3875

FREQUENCY (Hz)

0.000

0.500

1.000

1.500

2.000

2.500

3.000

100 1k 10k 100k

IL = 100mA

CIN = COUT = 10PF

NOISE (PV/ Hz

(

-40 -20 0 20 40 60 80 100 125

JUNCTION TEMPERATURE (oC)

0.5

1.5

2.5

DC LOAD REGULATION (mV/A)

-40 -20 0 20 40 60 80 100 125

JUNCTION TEMPERATURE (oC)

0.5

1.5

2.5

' VOUT/VOLT CHANGE in VIN (mV)

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

Typical Characteristics (continued)

Unless otherwise specified: TJ= 25°C, COUT = 10 µF, CIN = 10 µF, SD pin is tied to VIN, VOUT = 2.5 V, VIN = VO(NOM) + 1 V, IL=

10 mA

Figure 5. DC Load Reg. vs Junction Temperature Figure 6. DC Line Regulation vs Temperature

Figure 7. Noise vs Frequency

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

7 Detailed Description

7.1 Overview

The LP387x linear regulators are designed to provide an ultra-low-dropout voltage with excellent transient

response and load/line regulation. For battery-powered always-on type applications, the very low quiescent

current of LP387x in shutdown mode helps reduce battery drain. For applications where load is not placed close

to the regulator, LP3875 incorporates a voltage sense circuit to improve voltage regulation at the point of load.

ERROR output pin of LP3872 can be used in the system to flag a low-voltage condition.

7.2 Functional Block Diagram

Figure 8. LP3872

Figure 9. LP3875

7.3 Feature Description

7.3.1 Shutdown (SD)

The LM387x devices have a shutdown feature that turns the device off and reduces the quiescent current to 10

nA, typical.

Product Folder Links: LP3872 LP3875

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

Feature Description (continued)

7.3.2 Load Voltage Sense

In applications where the regulator output is not very close to the load, LP3875 can provide better remote load

regulation using the SENSE pin. Figure 10 depicts the advantage of the SENSE option. LP3872 regulates the

voltage at the OUT pin. Hence, the voltage at the remote load will be the regulator output voltage minus the drop

across the trace resistance. For example, in the case of a 3.3-V output, if the trace resistance is 100 mΩ, the

voltage at the remote load will be 3.15 V with 1.5 A of load current, ILOAD. The LP3875 regulates the voltage at

the sense pin. Connecting the sense pin to the remote load will provide regulation at the remote load, as shown

in Figure 10. If the sense option pin is not required, the SENSE pin must be connected to the OUT pin.

Figure 10. Improving Remote Load Regulation Using LP3875

7.3.3 Short-Circuit Protection

The LP3872 and LP3875 devices are short-circuit protected and in the event of a peak overcurrent condition, the

short-circuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts

down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the

thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency.

7.3.4 Low Dropout Voltage

The LP387x devices feature an ultra-low-dropout voltage, typically 38 mV at 150-mA load current and 380 mV at

1.5-A load current.

7.4 Device Functional Modes

7.4.1 Shutdown Mode

A CMOS Logic low level signal at the shutdown (SD) pin will turn off the regulator. The SD pin must be actively

terminated through a 10-kΩpullup resistor for a proper operation. If this pin is driven from a source that actively

pulls high and low (such as a CMOS rail to rail comparator), the pullup resistor is not required. This pin must be

tied to VIN if not used.

7.4.2 Active Mode

When voltage at SD pin of the LP387x device is at logic high level, the device is in normal mode of operation.

7.4.3 ERROR Flag Operation

The LP3872 and LP3875 produces a logic low signal at the ERROR Flag pin when the output drops out of

regulation due to low input voltage, current limiting, or thermal limiting. This flag has a built-in hysteresis. The

timing diagram in Figure 11 shows the relationship between the ERROR flag and the output voltage. In this

example, the input voltage is changed to demonstrate the functionality of the ERROR Flag.

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

Device Functional Modes (continued)

The internal ERROR flag comparator has an open-drain output stage. Hence, the ERROR pin should be pulled

high through a pullup resistor. Although the ERROR flag pin can sink current of 1 mA, this current is energy drain

from the input supply. Hence, the value of the pullup resistor should be in the range of 10 kΩto 1 MΩ.The

ERROR pin must be connected to ground if this function is not used. It should also be noted that when the SD

pin is pulled low, the ERROR pin is forced to be invalid for reasons of saving power in shutdown mode.

Figure 11. ERROR Flag Operation

Product Folder Links: LP3872 LP3875

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

8 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

8.1 Application Information

The LP387x devices are linear regulators designed to provide high load current of up to 1.5 A, low dropout

voltage, and low quiescent current in shutdown mode. Figure 12 and Figure 13 show the typical application

circuit for these devices.

8.1.1 Dropout Voltage

The dropout voltage of a regulator is defined as the minimum input-to-output differential required to stay within

2% of the nominal output voltage. For CMOS LDOs, the dropout voltage is the product of the load current and

the Rds(on) of the internal MOSFET.

8.1.2 Reverse Current Path

The internal MOSFET in LP3872 and LP3875 has an inherent parasitic diode. During normal operation, the input

voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is

pulled above the input in an application, then current flows from the output to the input as the parasitic diode gets

forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to

200-mA continuous and 1-A peak.

8.2 Typical Application

*SD and ERROR pins must be pulled high through a 10-kΩpullup resistor. Connect the ERROR pin to ground if this

function is not used. See the Shutdown Mode and ERROR Flag Operation sections.

Figure 12. LP3872 Typical Application Circuit

*SD must be pulled high through a 10-kΩpullup resistor. See the Shutdown Mode section.

Figure 13. LP3875 Typical Application Circuit

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

Typical Application (continued)

8.2.1 Design Requirements

Table 1. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE

Input voltage range 2.5 V to 7 V

Output voltage 1.8 V

Output current 1.5 A

Output capacitor 10 µF

Input capacitor 10 µF

Output capacitor ESR range 100 mΩto 4 Ω

8.2.2 Detailed Design Procedure

8.2.2.1 Power Dissipation and Device Operation

The permissible power dissipation for any package is a measure of the capability of the device to pass heat from

the power source, the junctions of the IC, to the ultimate heat sink, the ambient environment. Thus, the power

dissipation depends on the ambient temperature and the thermal resistance across the various interfaces

between the die junction and ambient air.

The maximum allowable power dissipation for the device in a given package can be calculated using Equation 1:

PD-MAX = ((TJ-MAX – TA) / RθJA) (1)

The actual power being dissipated in the device can be represented by Equation 2:

PD= (VIN – VOUT)×IOUT (2)

Equation 1 and Equation 2 establish the relationship between the maximum power dissipation allowed due to

thermal consideration, the voltage drop across the device, and the continuous current capability of the device.

These two equations should be used to determine the optimum operating conditions for the device in the

application.

In applications where lower power dissipation (PD) and/or excellent package thermal resistance (RθJA) is present,

the maximum ambient temperature (TA-MAX) may be increased.

In applications where high power dissipation and/or poor package thermal resistance is present, the maximum

ambient temperature (TA-MAX) may have to be derated. TA-MAX is dependent on the maximum operating junction

temperature (TJ-MAX-OP = 125°C), the maximum allowable power dissipation in the device package in the

application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (RθJA),

as given by Equation 3:

TA-MAX = (TJ-MAX-OP – (RθJA × PD-MAX)) (3)

Alternately, if TA-MAX can not be derated, the PDvalue must be reduced. This can be accomplished by reducing

VIN in the VIN – VOUT term as long as the minimum VIN is met, or by reducing the IOUT term, or by some

combination of the two.

8.2.2.2 External Capacitors

Like any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be

correctly selected for proper performance.

• Input Capacitor: An input capacitor of at least 10 µF is required. Ceramic, tantalum, or Electrolytic capacitors

may be used, and capacitance may be increased without limit.

• Output Capacitor: An output capacitor is required for loop stability. It must be located less than 1 cm from the

device and connected directly to the output and ground pins using traces which have no other currents

flowing through them (see Layout section).

The minimum value of output capacitance that can be used for stable full-load operation is 10 µF, but it may be

increased without limit. The output capacitor must have an equivalent series resistance (ESR) value as shown in

Figure 14. Tantalum capacitors are recommended for the output capacitor.

Product Folder Links: LP3872 LP3875

COUT ESR (:)

LOAD CURRENT (A)

STABLE REGION

COUT > 10 PF

012

.001

.01

0.1

1.0

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

Figure 14. ESR Curve

8.2.2.3 Selecting a Capacitor

Capacitance tolerance and variation with temperature must be considered when selecting a capacitor so that the

minimum required amount of capacitance is provided over the full operating temperature range. In general, a

good tantalum capacitor will show very little capacitance variation with temperature, but a ceramic may not be as

good (depending on dielectric type). Aluminum electrolytics also typically have large temperature variation of

capacitance value.

Equally important to consider is how ESR of a capacitor changes with temperature: this is not an issue with

ceramics, as their ESR is extremely low. However, it is very important in tantalum and aluminum electrolytic

capacitors. Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic

capacitors is so severe they may not be feasible for some applications (see Capacitor Characteristics).

8.2.2.4 Capacitor Characteristics

8.2.2.4.1 Ceramic

For values of capacitance in the 10-µF to 100-µF range, ceramics are usually larger and more costly than

tantalums but give superior AC performance for bypassing high frequency noise because of very low ESR

(typically less than 10 mΩ). However, some dielectric types do not have good capacitance characteristics as a

function of voltage and temperature.

Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or

Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V

also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of

the temperature range.

X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically

maintain a capacitance range within ±20% of nominal over full operating ratings of temperature and voltage. Of

course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance.

8.2.2.4.2 Tantalum

Solid tantalum capacitors are recommended for use on the output because their typical ESR is very close to the

ideal value required for loop compensation. They also work well as input capacitors if selected to meet the ESR

requirements previously listed.

Tantalums also have good temperature stability: a good quality tantalum will typically show a capacitance value

that varies less than 10-15% across the full temperature range of −40°C to 125°C. ESR will vary only about 2X

going from the high to low temperature limits.

The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if

the ESR of the capacitor is near the upper limit of the stability range at room temperature).

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

8.2.2.4.3 Aluminum

This capacitor type offers the most capacitance for the money. The disadvantages are that they are larger in

physical size, not widely available in surface mount, and have poor AC performance (especially at higher

frequencies) due to higher ESR and equivalent series inductance (ESL).

Compared by size, the ESR of an aluminum electrolytic is higher than either tantalum or ceramic, and it also

varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50X

when going from 25°C down to −40°C.

It should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which

indicates they have poor high-frequency performance. Only aluminum electrolytics that have an impedance

specified at a higher frequency (from 20 kHz to 100 kHz) should be used for the LP387x. Derating must be

applied to the manufacturer's ESR specification, because it is typically only valid at room temperature.

Any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating

temperature where ESR is maximum.

8.2.2.5 Turnon Characteristics for Output Voltages Programmed to 2 V or Less

As VIN increases during start-up, the regulator output will track the input until Vin reaches the minimum operating

voltage (typically about 2.2 V). For output voltages programmed to 2 V or less, the regulator output may

momentarily exceed its programmed output voltage during start-up. Outputs programmed to voltages above 2 V

are not affected by this behavior.

8.2.2.6 RFI/EMI Susceptibility

Radio frequency interference (RFI) and electromagnetic interference (EMI) can degrade the performance of any

IC because of the small dimensions of the geometries inside the device. In applications where circuit sources are

present which generate signals with significant high frequency energy content (> 1 MHz), care must be taken to

ensure that this does not affect the IC regulator.

If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes

from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the IC.

If a load is connected to the IC output which switches at high speed (such as a clock), the high-frequency current

pulses required by the load must be supplied by the capacitors on the IC output. Because the bandwidth of the

regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that frequency.

This means the effective output impedance of the IC at frequencies above 100 kHz is determined only by the

output capacitors.

In applications where the load is switching at high speed, the output of the IC may need RF isolation from the

load. It is recommended that some inductance be placed between the output capacitor and the load, and good

RF bypass capacitors be placed directly across the load.

PCB layout is also critical in high noise environments, because RFI/EMI is easily radiated directly into PC traces.

Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At

MHz frequencies, ground planes begin to look inductive and RFI/EMI can cause ground bounce across the

ground plane.

In multilayer PCB applications, care should be taken in layout so that noisy power and ground planes do not

radiate directly into adjacent layers which carry analog power and ground.

8.2.2.7 Output Noise

Noise is specified in two ways:

• Spot Noise (or Output Noise Density): the RMS sum of all noise sources, measured at the regulator output, at

a specific frequency (measured with a 1-Hz bandwidth). This type of noise is usually plotted on a curve as a

function of frequency.

• Total Output Noise (or Broad-Band Noise): the RMS sum of spot noise over a specified bandwidth, usually

several decades of frequencies.

Attention should be paid to the units of measurement. Spot noise is measured in units µV/√Hz or nV/√Hz and

total output noise is measured in µV(rms).

Product Folder Links: LP3872 LP3875

VOUT

100mV/DIV

ILOAD

1A/DIV

TIME (50Ps/DIV)

MAGNITUDE

VOUT

100mV/DIV

ILOAD

1A/DIV

TIME (50Ps/DIV)

MAGNITUDE

VOUT

100mV/DIV

ILOAD

1A/DIV

TIME (50Ps/DIV)

MAGNITUDE

VOUT

100mV/DIV

ILOAD

1A/DIV

TIME (50Ps/DIV)

MAGNITUDE

VOUT

100mV/DIV

ILOAD

1A/DIV

TIME (50Ps/DIV)

MAGNITUDE

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

The primary source of noise in low-dropout regulators is the internal reference. In CMOS regulators, noise has a

low frequency component and a high frequency component, which depend strongly on the silicon area and

quiescent current. Noise can be reduced in two ways: by increasing the transistor area or by increasing the

current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a

smaller package. Increasing the current drawn by the internal reference increases the total supply current

(ground pin current). Using an optimized trade-off of ground pin current and die size, LP3872 and LP3875

achieves low noise performance and low quiescent current operation.

The total output noise specification for LP3872 and LP3875 is presented in Electrical Characteristics. The Output

noise density at different frequencies is represented by a curve under typical performance characteristics.

8.2.3 Application Curves

CIN = COUT = 100 µF, OSCON

CIN = COUT = 10 µF, OSCON Figure 16. Load Transient Response

Figure 15. Load Transient Response

CIN = COUT = 100 µF, POSCAP CIN = COUT = 10 µF, Tantalum

Figure 17. Load Transient Response Figure 18. Load Transient Response

CIN = COUT = 100 µF, Tantalum Figure 19. Load Transient Response

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

9 Power Supply Recommendations

The LP397x devices are designed to operate from an input supply voltage range of 2.5 V to 7 V. The input

supply should be well regulated and free of spurious noise. To ensure that the LP387x output voltage is well

regulated, the input supply should be at least VOUT + 0.5 V, or 2.5 V, whichever is higher. A minimum capacitor

value of 10 μF is required to be within 1 cm of the IN pin.

10 Layout

10.1 Layout Guidelines

Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops.

The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator

using traces which do not have other currents flowing in them (Kelvin connect).

The best way to do this is to lay out CIN and COUT near the device with short traces to the IN, OUT, and GND

pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its

capacitors have a single-point ground.

It should be noted that stability problems have been seen in applications where vias to an internal ground plane

were used at the ground points of the IC and the input and output capacitors. This was caused by varying ground

potentials at these nodes resulting from current flowing through the ground plane. Using a single-point ground

technique for the regulator and it's capacitors fixed the problem.

Because high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor

leads to these pins so there is no voltage drop in series with the input and output capacitors.

Product Folder Links: LP3872 LP3875

CIN

VOUT

VIN IN

OUT

ERROR/SENSE

GND

COUT

GND

OUT

ERROR/SENSE

VIN

VOUT

COUT

CIN

Layout Example for SOT-223 Package

Layout Example for TO-263 Package

LP3872

LP3875

www.ti.com

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

10.2 Layout Examples

Product Folder Links: LP3872 LP3875

LP3872

LP3875

SNVS227H –FEBRUARY 2003–REVISED JANUARY 2015

www.ti.com

11 Device and Documentation Support

11.1 Related Links

Table 2 below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 2. Related Links

TECHNICAL TOOLS & SUPPORT &

PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY

LP3872 Click here Click here Click here Click here Click here

LP3875 Click here Click here Click here Click here Click here

11.2 Trademarks

All trademarks are the property of their respective owners.

11.3 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

11.4 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

Product Folder Links: LP3872 LP3875

PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LP3872EMP-1.8/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHAB

LP3872EMP-2.5/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHBB

LP3872EMP-3.3/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHCB

LP3872EMP-5.0 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LHDB

LP3872EMP-5.0/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHDB

LP3872EMPX-2.5/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHBB

LP3872EMPX-3.3/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHCB

LP3872ES-1.8 NRND DDPAK/

TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3872ES

-1.8

LP3872ES-1.8/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-1.8

LP3872ES-2.5 NRND DDPAK/

TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3872ES

-2.5

LP3872ES-2.5/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-2.5

LP3872ES-3.3/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-3.3

LP3872ES-5.0 NRND DDPAK/

TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3872ES

-5.0

LP3872ES-5.0/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-5.0

LP3872ESX-1.8/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-1.8

LP3872ESX-2.5/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-2.5

LP3872ESX-3.3/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-3.3

PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2017

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LP3872ESX-5.0/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3872ES

-5.0

LP3875EMP-1.8/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHLB

LP3875EMP-2.5/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHNB

LP3875EMP-3.3/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHPB

LP3875EMP-5.0/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LHRB

LP3875ES-1.8/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-1.8

LP3875ES-2.5/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-2.5

LP3875ES-3.3/NOPB ACTIVE DDPAK/

TO-263 KTT 5 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-3.3

LP3875ESX-1.8/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-1.8

LP3875ESX-2.5/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-2.5

LP3875ESX-3.3/NOPB ACTIVE DDPAK/

TO-263 KTT 5 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3875ES

-3.3

LP3875ET-3.3/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP3875ET

-3.3

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

PACKAGE OPTION ADDENDUM

www.ti.com 14-Oct-2017

Addendum-Page 3

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LP3872EMP-1.8/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMP-2.5/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMP-3.3/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMP-5.0 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMP-5.0/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMPX-2.5/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872EMPX-3.3/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3872ESX-1.8/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3872ESX-2.5/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3872ESX-3.3/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3872ESX-5.0/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3875EMP-1.8/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3875EMP-2.5/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3875EMP-3.3/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LP3875EMP-5.0/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

PACKAGE MATERIALS INFORMATION

www.ti.com 2-Sep-2015

Pack Materials-Page 1

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LP3875ESX-1.8/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3875ESX-2.5/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LP3875ESX-3.3/NOPB DDPAK/

TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LP3872EMP-1.8/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3872EMP-2.5/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3872EMP-3.3/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3872EMP-5.0 SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3872EMP-5.0/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3872EMPX-2.5/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0

LP3872EMPX-3.3/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0

LP3872ESX-1.8/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3872ESX-2.5/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3872ESX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3872ESX-5.0/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3875EMP-1.8/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 2-Sep-2015

Pack Materials-Page 2

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LP3875EMP-2.5/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3875EMP-3.3/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3875EMP-5.0/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0

LP3875ESX-1.8/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3875ESX-2.5/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

LP3875ESX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0

PACKAGE MATERIALS INFORMATION

www.ti.com 2-Sep-2015

Pack Materials-Page 3

MECHANICAL DATA

NDC0005A

www.ti.com

MECHANICAL DATA

NDH0005D

www.ti.com

MECHANICAL DATA

KTT0005B

www.ti.com

BOTTOM SIDE OF PACKAGE

TS5B (Rev D)

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LP3875EMP-1.8 LP3875EMP-1.8/NOPB LP3875EMP-2.5 LP3875EMP-2.5/NOPB LP3875EMP-3.3 LP3875EMP-

3.3/NOPB LP3875EMP-5.0 LP3875EMP-5.0/NOPB LP3875EMP-ADJ LP3875EMPX-ADJ LP3875ES-1.8

LP3875ES-1.8/NOPB LP3875ES-2.5 LP3875ES-2.5/NOPB LP3875ES-3.3 LP3875ES-3.3/NOPB LP3875ESX-1.8

LP3875ESX-1.8/NOPB LP3875ESX-2.5 LP3875ESX-2.5/NOPB LP3875ESX-3.3 LP3875ESX-3.3/NOPB

LP3875ESX-ADJ LP3875ET-3.3 LP3875ET-3.3/NOPB