This is information on a product in full production.
April 2014 DocID17488 Rev 4 1/17
LD59015
150 mA low noise and high PSRR linear voltage regulator
Datasheet
-
production data
Features
•Input voltage from 2.4 to 5.5 V
•Very low quiescent current (31 µA typ. at no
load, 75 µA typ. at 150 mA load, 1 µA max. in
OFF mode)
•Very low noise (20 µV
RMS
at V
OUT
= 1.5 V)
•Output voltage tolerance: ± 1.8% at 25 °C
•150 mA guaranteed output current
•Wide range of output voltages available on
request: 0.8 V to 3.3 V in 100 mV steps
•Logic-controlled electronic shutdown
•Compatible with ceramic capacitors
•Very high PSRR (80 dB @ 100 Hz, 76 @
10 kHz, 54 @ 100 kHz)
•Internal current and thermal limit
•Package: SOT323-5L
•Temperature range: -40 °C to 125 °C
Description
The LD59015 provides 150 mA maximum current
with an input voltage range from 2.4 V to 5.5 V,
and a typical dropout voltage of 150 mV. It is
stable with ceramic capacitors. High PSRR, low
quiescent current and low noise features make it
suitable for low power batt ery-powered
applications. Power supply rejection is 80 dB at
low frequency and starts to roll off at 10 kHz. The
enable logic control function puts the LD59015 in
shutdown mode, allowing a total current
consumption lower than 1 µA. The device also
includes short-circuit constant current limiting and
thermal pr otecti on. Typical ap plic ati ons are
mobile phones, personal digital assistants
(PDAs), cordless phones and similar battery-
powered systems.
SOT323-5L
Table 1. Device summary
Order codes Output voltages
LD59015C08R 0.8 V
LD59015C12R 1.2 V
LD59015C15R 1.5 V
LD59015C18R 1.8 V
LD59015C25R 2.5 V
LD59015C30R 3.0 V
LD59015C33R 3.3 V
www.st.com
Contents LD59015
2/17 DocI D17488 Rev 4
Contents
1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DocID17488 Rev 4 3/17
LD59015 Block di agram
17
1 Block diagram
Figure 1. LD59015 block diagram
Trimming
0.8 V
BandGap
Enable
EN GND
OUT
IN
Protection
Thermal R2
R1
Trimming
0.8 V
BandGap
Enable
EN GND
OUT
IN
Protection
Thermal R2
R1
Pin configuration LD59015
4/17 DocI D17488 Rev 4
2 Pin configuration
Figure 2. Pin connection (top view)
Table 2.
Pin description
Pin n° Symbol Function
1 IN Input voltage
2 GND Ground
3EN
Enable input
Set V
EN
> 0.9 to turn on the device
Set V
EN
< 0.4 to turn off the device
4 N.C. Not connected
5 OUT Output voltage
DocID17488 Rev 4 5/17
LD59015 Typical application
17
3 Typical application
Figure 3. Typic al application circuit
1 µF
IN
EN
V
EN
V
IN
OUT
Load
GND
1 µF
V
OUT
1 µF
IN
EN
V
EN
V
IN
OUT
Load
GND
1 µF
V
OUT
Maximum ratings LD59015
6/17 DocI D17488 Rev 4
4 Maximum ratings
Note: Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. All values are referred to GND.
Table 3. Absolute maximum ratings
Symbol Parameter Value Unit
V
IN
DC input voltage - 0.3 to 7 V
V
OUT
DC output voltage - 0.3 to V
I
+ 0.3 (max. 7) V
V
EN
Enable input voltage - 0.3 to V
I
+ 0.3 (max. 7) V
I
OUT
Output current Internally limited mA
P
D
Power dissipation Internally limited mW
ESD Human bod y mod el ±
3kV
Machine model ± 300 V
T
STG
Storage temperature range -65 to 150 °C
T
OP
Operating junction temperature range -40 to 125 °C
Table 4. Thermal data
Symbol Parameter Value Unit
R
thJA
Thermal resistance junction-ambient 645.69 °C/W
R
thJC
Thermal resistance junction-case 116 °C/W
DocID17488 Rev 4 7/17
LD59015 Electri cal chara ct er ist ics
17
5 Electrical characteristics
T
J
= 2 5 °C, V
IN
= V
OUT(NOM)
+ 1 V, C
IN
= C
OUT
= 1 µF, I
OUT
= 1 mA, V
EN
= V
IN
, unles s
otherwise specified.
Table 5. Electrical characteristics
(1)
Symbol Parameter Test conditions Min. Typ. Max. Unit
V
IN
Operating input voltage 2.4 5.5
V
V
UVLO
Turn-on threshold 2.0 2.15
Turn-of f thres ho ld 1.90 1.95
V
OUT
V
OUT
accuracy I
OUT
= 1mA, -40°C < T
J
< 125°C -1.8 1.8 %
ΔV
OUT
Static line regulation V
OUT
+1V ≤ V
IN
≤ 5.5V, I
OUT
= 1mA 0.001 %/V
ΔV
OUT
Static load regulation I
OUT
= 1mA to 150mA 0.001 %/mA
V
DROP
Dropout voltage
(2)
I
OUT
= 150mA, V
OUT
> 2.2V
-40°C < T
J
< 125°C 150 210 mV
e
N
Output noise voltage 10Hz to 100kHz, I
OUT
= 10mA,
V
OUT
= 1.5V 20 µV
RMS
/V
OUT
SVR Supply volta ge reje cti on
V
OUT
= 1.5V
V
IN
= V
OUTNOM
+ 1V +/-V
RIPPLE
V
RIPPLE
= 0.5V, frequency = 1kHz
I
OUT
= 1mA 76
dB
V
IN
= V
OUTNOM
+ 1V +/-V
RIPPLE
V
RIPPLE
= 0.5V, frequency =10kHz
I
OUT
= 1mA 76
V
IN
= V
OUTNOM
+ 1V +/-V
RIPPLE
V
RIPPLE
= 0.5V, frequency =100kHz
I
OUT
= 1mA 54
I
Q
Quiescent current
I
OUT
= 0mA 31
µA
I
OUT
= 0mA, -40°C < T
J
< 125°C 60
I
OUT
= 0 to 150mA 75
I
OUT
= 0 to 150mA
-40°C < T
J
< 125°C 110
V
IN
input current in OFF mode:
V
EN
= GND 0.001 1
I
SC
Short-circuit current R
L
= 0 200 mA
V
EN
Enable input logic low V
IN
= 2.4V to 5.5V,
-40°C < T
J
< 85°C 0.4 V
Enable in put logic high V
IN
= 2.4V to 5.5V,
-40°C < T
J
< 85°C 0.9 V
I
EN
Enable pin input current V
SHDN
= 5.5V 0.1 100 nA
T
ON
Turn-on time
(3)
200 µs
Ele ctrical characteristics LD59015
8/17 DocI D17488 Rev 4
Note: All transient values are guaranteed by design, not tested in production.
T
SHDN
Thermal shutdown 160 °C
Hysteresis 20
C
OUT
Output capacitor Capacitance (s ee typical
performan ce cha rac teri st ics for
stability) 14.7µF
1. For V
OUT(NOM)
< 1.3 V, V
IN
= 2.4 V.
2. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply to output voltages below 1.7 V.
3. Turn-on time is time measured between the enable input just exceeding V
EN
high value and the output voltage just
reaching 95% of its nominal value.
Table 5. Electrical characteristics (continued)
(1)
Symbol Parameter Test conditions Min. Typ. Max. Unit
DocID17488 Rev 4 9/17
LD59015 Typical performance characteristics
17
6 Typical performance characteristics
C
IN
= C
OUT
= 1 µF
Figure 4. V
OUT
vs. temperature (V
OUT
= 0.8 V) Figure 5. V
OUT
vs. temperature (V
OUT
= 3.3 V)
Figure 6. Quiescent current vs. temperature Figure 7. Quiescent current vs. I
OUT
Figure 8. V
OUT
vs. V
IN
Figure 9. V
DROP
vs. I
OUT
V
IN
= V
EN
= 4.3 V, I
OUT
= 1 mA, V
OUT
= 3.3 V
3.22
3.24
3.26
3.28
3.3
3.32
3.34
3.36
3.38
-75 -50 -25 0 25 50 75 100 125 150
T [°C]
V
OUT
[V]
V
IN
= V
EN
= 4.3 V, I
OUT
= 1 mA, V
OUT
= 3.3 V
3.22
3.24
3.26
3.28
3.3
3.32
3.34
3.36
3.38
-75 -50 -25 0 25 50 75 100 125 150
T [°C]
V
OUT
[V]









 
@@$>$
>
T,T,
@@&&>H>HUUXXWDWDUHSPH7UHSPH7
99
1,1,
99
1,1,
9999

2
99
9999
2
99
10.00
20.00
30.00
40.00
50.00
60.00
70.00
80.00
90.00
100.00
0 20 40 60 80 100 120 140 160
IOUT [mA]
Iq [uA]
-40°C 125°C 25°C
10.00
20.00
30.00
40.00
50.00
60.00
70.00
80.00
90.00
100.00
0 20 40 60 80 100 120 140 160
IOUT [mA]
Iq [uA]
-40°C 125°C 25°C
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
00.511.522.533.544.555.56
V
IN
[V]
V
OUT
[V]
150 ºC
125 ºC
85 ºC
55 ºC
25 ºC
0 ºC
-25 ºC
-40 ºC
-55 ºC
V
IN
= V
EN
= from 0 to 5.5 V, I
OUT
= 150 mA,
V
OUT
= 8 V
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
00.511.522.533.544.555.56
V
IN
[V]
V
OUT
[V]
150 ºC
125 ºC
85 ºC
55 ºC
25 ºC
0 ºC
-25 ºC
-40 ºC
-55 ºC
V
IN
= V
EN
= from 0 to 5.5 V, I
OUT
= 150 mA,
V
OUT
= 8 V
V
IN
= V
EN
, I
OUT
= from 0 to 150 mA, V
OUT
= 3.3 V
0
50
100
150
200
250
0 25 50 75 100 125 150 175
I
OUT
[mA]
Vdrop [mV]
125 ºC
-40 ºC
25 ºC
V
IN
= V
EN
, I
OUT
= from 0 to 150 mA, V
OUT
= 3.3 V
0
50
100
150
200
250
0 25 50 75 100 125 150 175
I
OUT
[mA]
Vdrop [mV]
125 ºC
-40 ºC
25 ºC
Typical performance characteristics LD59015
10/17 DocID17488 Rev 4
Figure 10. V
UVLO
vs. temperature Figure 11. ESR vs. C
OUT
Figure 12. Supply voltage rejection vs.
frequency Figure 13. Supply voltage rejection vs. I
OUT
Figure 14. I
SC
vs. V
DROP
Figure 15. Line transient (V
OUT
= 0.8 V)
C
OUT
= 1 µF; V
IN
= V
EN
= from 2.4 to 3.3 V; V
OUT
= 0.8 V;
I
OUT
= 1 mA; t
rise
= t
fall
= 25 µs
40
50
60
70
80
90
100
100 1000 10000 100000
Supply Voltage rejection [dB]
f [Hz]
V
IN
= 4.8 V, Vripple pk-pk = 1 V, V
O
= 3.3 V
40
50
60
70
80
90
0 20 40 60 80 100 120 140 160
I
OUT
[mA]
Supply voltage rejection [db]
1 kHz
100 Hz
10 kHz
V
IN
= 4.8 V, Vripple pk-pk = 1 V, V
O
= 3.3 V
40
50
60
70
80
90
0 20 40 60 80 100 120 140 160
I
OUT
[mA]
Supply voltage rejection [db]
1 kHz
100 Hz
10 kHz
V
IN
= V
EN
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0123456
Vdrop [V]
I
SC
[A]
125 ºC
-40 ºC
25 ºC
V
IN
= V
EN
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0123456
Vdrop [V]
I
SC
[A]
125 ºC
-40 ºC
25 ºC
DocID17488 Rev 4 11/17
LD59015 Typical performance characteristics
17
Figure 16. Line trans ien t (V
OUT
= 3.3 V) Figure 17. Load transient (V
OUT
= 0.8 V)
C
OUT
= 1 µF; V
IN
= V
EN
= from 4.5 to 5.5 V; V
OUT
= 3.3 V ;
I
OUT
= 1 mA; t
rise
= t
fall
= 25 µs
C
IN
= C
OUT
= 1 µF; V
IN
= V
EN
= 2.4 V; V
OUT
= 0.8 V ;
I
OUT
from 0.1 to 150 mA; t
rise
= t
fall
= 25 µs
Figure 18. Load transient (V
OUT
= 3.3 V) Figure 19. Start-up transient
C
IN
= C
OUT
= 1 µF; V
IN
= V
EN
= 4.3 V ; V
OUT
= 3.3 V;
I
OUT
from 0.1 to 150 mA; t
rise
= t
fall
= 25 µs
C
OUT
= 1 µF; V
IN
= V
EN
= from 0 to 5.5 V; V
OUT
= 3.3 V ;
I
OUT
= 150 mA
Fig ure 20. Enable transient
C
IN
= C
OUT
= 1 µF; V
IN
= 4.3; V
EN
= from 0 to 5.5 V;
V
OUT
= 3.3 V; I
OUT
= 1 mA; t
rise
= 25 µs
Package mechanical data LD59015
12/17 DocID17488 Rev 4
7 Package mechanical data
In orde r to meet en vironmental requi rements, ST offers these devices in different grades of
ECOPACK
®
packages, dependi ng on their level of environmental com pliance. ECOPACK
®
specifications, grade definitions and product status are available at:
www.st.com
.
ECOPACK
®
is an ST trademark.
Figure 21. SOT323-5L drawings
7091413_E
DocID17488 Rev 4 13/17
LD59015 Package mechanical data
17
Table 6. SOT323-5L mechanical data
Dim. mm
Min. Typ. Max.
A 0.80 1.10
A1 0 0.10
A2 0.80 0.90 1
b 0.15 0.30
c 0.10 0.22
D1.8022.20
E 1.80 2.10 2.40
E1 1.15 1.25 1.35
e0.65
e1 1.30
L 0.26 0.36 0.46
<0° 8°
Packagi ng mechan ic al data LD59015
14/17 DocID17488 Rev 4
8 Packaging mechanical data
Figure 22. SOT323-5L tape and reel drawings
DocID17488 Rev 4 15/17
LD59015 Packaging mechanical data
17
Table 7. SOT323-5L t ape and reel mechanical dat a
Dim. mm
Min. Typ. Max.
A 175 180 185
C12.81313.2
D20.2
N59.56060.5
T14.4
Ao 2.25
Bo 3.17
Ko 1.2
Po 3.9 4.0 4.1
P 3.9 4.0 4.2
Revision history LD59015
16/17 DocID17488 Rev 4
9 Revision history
Table 8. Document rev ision history
Date Revision Changes
10-May-2010 1 Initial release.
21-Dec-2011 2 Modified: operating input voltage (V
IN
) min. value Table 5 on page 7.
Availability LD59015C08R code Table 1 on page 1.
06-Jul-2012 3 Updated: Table 1 on pag e 1 .
24-Apr-2014 4
Part number LD59015xx changed to LD59015.
Updated the description in cover page and Section 7: Package mechanical
data.
Added Section 8: Packaging mechanical data.
Minor text changes.
DocID17488 Rev 4 17/17
LD59015
17
Please Read Carefully:
Informa tion in this do cument is prov ided solely in connec tion with ST products. STMic roelect ronics NV and its subsidiari es (“ST”) reser ve the
right to mak e chang es, c or recti ons , modif ic ations or improv ement s, t o th is documen t, and the prod ucts an d servic es des crib ed he rein a t any
time, without notice.
All ST produ cts are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes n o
liability whatsoever relating to the choice, selection or use of the ST produc ts and services described herein .
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST produ cts with provis ions different f rom the statement s and/or technic al features set forth in this document shall i mmediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liabili ty of ST.
ST and the ST logo are trade marks or registered trademarks of ST in various countries.
Information in this document su persedes and replac es all information previously supplie d.
The ST logo is a registered trademark of STMicroelectronic s. All other names are t he property of their respective owners.
© 2014 STMicroelec tronics - All rights rese rved
STMicroelectronics gro up of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - Unit ed Kingdom - United Stat es of America
www.st.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
STMicroelectronics:
LD59015C33R LD59015C12R LD59015C15R LD59015C18R LD59015C25R LD59015C30R