INCH-POUND MIL-PRF-39018/3G 20 February 2009 SUPERSEDING MIL-PRF-39018/3F 24 April 2007 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, ELECTROLYTIC (ALUMINUM OXIDE) (POLARIZED), NON-ESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYLES CU16 (UNINSULATED), CU17 (INSULATED), AND CUR17 (INSULATED) STYLE CU16 INACTIVE FOR DESIGN AFTER 23 MARCH 1972 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the capacitors described herein shall consist of this specification sheet and MIL-PRF-39018. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. These capacitors are not intended to be mounted by their leads. 4. For .625 diameter case, the leads shall be .032 +.008, -.002 diameter and for all other diameter cases the leads shall be .040 +.008, -.002 diameter. 5. The "D" dimensions for styles CU17 and CUR17 shall be not more than .008 (0.20 mm) larger than the specified bare case diameter. FIGURE 1. Styles CU16, CU17, and CUR17 capacitors. AMSC N/A FSC 5910 MIL-PRF-39018/3G Inches .002 .008 .015 .032 .040 .250 .625 .750 .875 1.000 1.125 1.328 1.625 1.828 2.125 2.238 2.500 2.625 2.828 3.125 3.328 3.625 3.828 mm .05 .20 .38 .81 1.02 6.35 15.88 19.05 22.22 25.40 28.58 33.73 41.28 46.43 53.98 56.85 63.50 66.68 71.83 79.38 84.53 92.08 97.23 Dimensions Case size D1 D2 D3 D4 D5 D6 D7 E1 E2 E3 E4 E5 E6 E7 F1 F2 F3 F4 F5 F6 F7 L Min 1.125 1.125 1.125 1.625 1.625 1.625 1.625 2.125 2.125 2.125 2.125 2.625 2.625 2.625 2.625 3.125 3.125 3.125 3.625 3.625 3.625 Max 1.328 1.328 1.328 1.828 1.828 1.828 1.828 2.328 2.328 2.328 2.328 2.828 2.828 2.828 2.828 3.328 3.328 3.328 3.828 3.828 3.828 D .015 See note 5 .625 .750 .875 .625 .750 .875 1.000 .625 .750 .875 1.000 .625 .750 .875 1.000 .625 .875 1.000 .750 .875 1.000 FIGURE 1. Styles CU16, CU17, and CUR17 capacitors - Continued. 2 MIL-PRF-39018/3G REQUIREMENTS: Dimensions and configuration: See figure 1. Case: Type - Tubular. Material - Metal. Leads - See figure 1. DC rated voltage: See table I. Reverse voltage: 3.0 volts maximum. Capacitance (Cap.) value: See table I. Cap. tolerance: See table I. Failure rate level (CUR17 only): M, P, R, and S. Operating temperature range: -55C to +105C. Burn-in (CUR17 only): In accordance with MIL-PRF-39018. DC leakage (DCL): See table I. Equivalent series resistance (ESR): See table I. Low temperature exposure: DCL: See table I. Cap.: See table I. ESR: See table I. Terminal strength: Method 211 of MIL-STD-202, test condition A (3 pounds) and test condition D (3 rotations). Solderability: In accordance with MIL-PRF-39018. Stability at reduced and high temperatures: Step 1 (at +25C): DCL: See table I. Cap.: See table I. ESR: See table I. Step 2 (at -55C): Impedance: See table I. Cap.: Within the following percentages of the step 1 value: 7 V dc: 35 percent. 10 to 30 V dc inclusive: 25 percent 50 to 100 V dc inclusive: 20 percent. 150 to 350 V dc inclusive: 30 percent. Step 3 (at +25C): DCL: See table I. Cap.: Within 5 percent of step 1 value. ESR: See table I. Step 4 (at +105C): DCL: See table I. Cap.: Within 30 percent of step 1 value. ESR: See table I. Step 5 (at +25C): DCL: See table I. Cap.: Within 5 percent of step 1 value. ESR: See table I. 3 TABLE I. Styles CU16, CU17, and CUR17 capacitors. DC rated voltage +85C and 105C F 680 1,000 1,500 2,200 3,300 4,700 6,800 10,000 12,000 470 1,000 1,500 2,200 3,300 4,700 6,800 8,200 390 680 1,000 1,500 2,200 3,300 4,700 6,800 DC surge voltage +85C and +105C volts 10 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 See footnotes at end of table. ESR 25C 105C .78 .53 .35 .24 .16 .11 .08 .05 .04 .99 .46 .31 .21 .14 .10 .07 .06 .85 .49 .33 .22 .15 .10 .07 .05 Impedance (max) at -55C and 120 Hz .98 .66 .44 .30 .20 .14 .10 .07 .06 1.13 .53 .35 .24 .16 .11 .08 .06 1.02 .59 .40 .27 .18 .12 .07 .06 DC leakage 25C 5 9.3 6.2 4.2 2.9 2.0 1.3 .93 .77 8.5 4.0 2.7 1.8 1.2 .85 .59 .50 10 5.9 4.0 2.7 1.8 1.2 0.8 0.6 105C A 30 35 43 50 66 75 90 111 127 35 50 61 70 93 110 127 150 38 49 61 75 86 114 136 156 183 212 259 300 396 450 540 670 764 212 300 367 424 558 663 764 900 232 296 367 450 519 687 821 936 AC ripple current (max) 120 Hz at 85C 1/ mA 489 644 885 1,220 1,520 1,930 2,930 3,850 4,510 454 807 1,130 1,390 1,950 2,750 3,570 4,180 478 689 1,060 1,420 1,890 2,380 3,420 4,360 Case size Style CU16 Capacitance tolerance -10 +30 D1 D2 D4 E1 D6 D7 F5 F4 F7 D1 D4 E1 D6 E3 F5 F6 F7 D1 D2 E1 E2 E6 E4 F6 F7 0401 0402 0403 0404 0405 0406 0407 0408 0409 0410 0411 0412 0413 0414 0415 0416 0417 0418 0419 0420 0421 0422 0423 0424 0425 -10 +50 Percent --------------------------------------------------- Dash number Style CUR17 3/ Style CU17 2/ low frequency vibration Capacitance Capacitance tolerance tolerance -10 +75 -10 +30 0501 0502 0503 0504 0505 0506 0507 0508 0509 0510 0511 0512 0513 0514 0515 0516 0517 0518 0519 0520 0521 0522 0523 0524 0525 0601 0602 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0613 0614 0615 0616 0617 0618 0619 0620 0621 0622 0623 0624 0625 -10 +50 Percent --------------------------------------------------- -10 +75 -10 +30 0701 0702 0703 0704 0705 0706 0707 0708 0709 0710 0711 0712 0713 0714 0715 0716 0717 0718 0719 0720 0721 0722 0723 0724 0725 1001100210031004100510061007100810091010101110121013101410151016101710181019102010211022102310241025- -10 +50 Percent --------------------------------------------------- Style CUR17 3/ high frequency vibration Capacitance tolerance -10 +75 -10 +30 1101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125- 120112021203120412051206120712081209 1210121112121213121412151216121712181219122012211222122312241225- -10 +50 Percent --------------------------------------------------- -10 +75 1301130213031304130513061307130813091310131113121313 131413151316131713181319132013211322132313241325- MIL-PRF-39018/3G 4 volts 7 7 7 7 7 7 7 7 7 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 Cap. TABLE I. Styles CU16, CU17, and CUR17 capacitors - Continued. DC rated voltage +85C and 105C F 150 220 330 470 680 1,000 1,500 2,200 2,700 100 150 220 330 470 680 1,000 1,500 1,800 47 68 100 150 220 330 470 680 820 DC surge voltage +85C and +105C volts 40 40 40 40 40 40 40 40 40 60 60 60 60 60 60 60 60 60 90 90 90 90 90 90 90 90 90 ESR 25C 105C 2.21 1.51 1.00 .71 .44 .33 .22 .15 .12 1.33 .88 .60 .40 .28 .20 .13 .09 .07 2.82 1.95 1.33 .88 .60 .40 .28 .20 .16 See footnotes at end of table. Impedance (max) at -55C and 120 Hz 2.65 1.81 1.21 .85 .59 .40 .27 .18 .16 3.98 2.65 1.81 1.21 .84 .59 .40 .27 .22 8.47 5.85 3.98 2.65 1.81 1.21 .84 .59 .49 DC leakage 25C 27 14 12 10 6.0 4.0 2.7 1.8 1.6 25 15 13 8.1 5.6 3.9 2.7 1.8 1.5 57 39 27 18 13 8.1 6.7 3.9 3.2 105C A 33 47 51 54 69 86 110 122 136 37 46 55 66 79 90 111 147 196 29 37 43 53 68 80 91 110 122 201 284 307 328 418 519 663 734 821 222 276 335 396 474 540 670 883 1,196 174 225 259 318 410 483 551 662 734 AC ripple current (max) 120 Hz at 85C 1/ mA 296 390 536 609 957 1,230 1,680 2,350 2,560 241 322 417 580 619 946 1,300 1,920 2,260 166 217 281 391 540 781 1,010 1,290 1,520 Case size Style CU16 Capacitance tolerance -10 +30 D1 D2 D4 D3 E5 E3 E7 F6 F4 D1 D2 D3 D5 E2 D7 E4 F4 F7 D1 D2 D3 D5 E2 E7 F3 F4 F7 0426 0427 0428 0429 0430 0431 0432 0433 0434 0435 0436 0437 0438 0439 0440 0441 0442 --0443 0444 0445 0446 0447 0448 0449 0450 0451 -10 +50 Percent ------------------------------------------------------- Dash number Style CUR17 3/ Style CU17 2/ low frequency vibration Capacitance Capacitance tolerance tolerance -10 +75 -10 +30 0526 0527 0528 0529 0530 0531 0532 0533 0534 0535 0536 0537 0538 0539 0540 0541 0542 --0543 0544 0545 0545 0547 0548 0549 0550 0551 0626 0627 0628 0629 0630 0631 0632 0633 0634 0635 0636 0637 0638 0639 0640 0641 0642 0699 0643 0644 0645 0646 0647 0648 0649 0650 0651 -10 +50 Percent ------------------------------------------------------- -10 +75 -10 +30 0726 0727 0728 0729 0730 0731 0732 0733 0734 0735 0736 0737 0738 0739 0740 0741 0742 0799 0743 0744 0745 0746 0747 0748 0749 0750 0751 102610271028102910301031103210331034103510361037103810391040104110421099 104310441045104610471048104910501051- -10 +50 Percent ------------------------------------------------------- Style CUR17 3/ high frequency vibration Capacitance tolerance -10 +75 -10 +30 112611271128112911301131113211331134113511361137113811391140114111421199114311441145114611471148114911501151- 122612271228122912301231123212331234123512361237123812391240124112421299124312441245124612471248124912501251- -10 +50 Percent ------------------------------------------------------- -10 +75 132613271328132913301331133213331334133513361337133813391340134113421399 134313441345134613471348134913501351- MIL-PRF-39018/3G 5 volts 30 30 30 30 30 30 30 30 30 50 50 50 50 50 50 50 50 50 75 75 75 75 75 75 75 75 75 Cap. TABLE I. Styles CU16, CU17, and CUR17 capacitors - Continued. DC rated voltage +85C and 105C F 22 47 68 100 160 220 330 470 18 33 47 68 100 150 220 330 15 33 47 68 100 150 220 270 DC surge voltage +85C and +105C volts 125 125 125 125 125 125 125 125 175 175 175 175 175 175 175 175 225 225 225 225 225 225 225 225 ESR 25C 105C 6.03 2.82 1.95 1.33 .88 .60 .40 .28 7.37 4.02 2.82 1.95 1.33 .88 .60 .40 8.84 4.02 2.82 1.95 1.33 .88 .60 .49 See footnotes at end of table. Impedance (max) at -55C and 120 Hz 18.09 8.47 5.85 3.98 2.65 1.81 1.21 .84 22.10 12.06 8.47 5.85 3.98 2.65 1.81 1.21 26.53 12.06 8.47 5.85 3.98 2.65 1.81 1.47 DC leakage 25C 125 57 39 27 18 13 8.1 5.6 150 81 57 39 27 18 12 8.0 180 81 57 39 27 18 12 .9.8 105C A 25 33 40 50 61 79 93 171 25 36 41 49 61 77 86 114 27 41 47 59 70 86 109 120 150 201 241 300 367 474 563 670 155 217 246 296 367 464 519 687 164 244 284 354 519 424 657 722 AC ripple current (max) 120 Hz at 85C 1/ mA 113 180 232 389 444 613 906 1,150 103 170 192 304 362 528 627 966 94 162 230 304 362 506 736 873 Case size Dash number Style CUR17 3/ Style CU17 2/ low frequency vibration Capacitance Capacitance tolerance tolerance Style CU16 Capacitance tolerance -10 +30 D1 D2 D3 F2 D7 E4 F6 F7 D1 D4 D3 E5 D7 E7 F1 F7 D1 D3 E1 E5 D7 E4 F4 F7 0452 0453 0454 0455 0456 0457 0458 0459 0460 0461 0462 0463 0464 0465 0466 0467 0468 0469 0470 0471 0472 0473 0474 0475 -10 +50 Percent 0552 0553 0554 0555 0556 0557 0558 0559 0560 0561 0562 0563 0564 0565 0566 0567 0568 0569 0570 0571 0572 0573 0574 0575 -10 +75 -10 +30 ------------------------------------------------- 0652 0653 0654 0655 0656 0657 0658 0659 0660 0661 0662 0663 0664 0665 0666 0667 0668 0669 0670 0671 0672 0673 0674 0675 -10 +50 Percent 0752 0753 0754 0755 0756 0757 0758 0759 0760 0761 0762 0763 0764 0765 0766 0767 0768 0769 0770 0771 0772 0773 0774 0775 -10 +75 -10 +30 ------------------------------------------------- 105210531054105510561057105810591060106110621063106410651066106710681069107010711072107310741075- -10 +50 Percent 115211531154115511561157115811591160116111621163116411651166116711681169117011711172117311741175- Style CUR17 3/ high frequency vibration Capacitance tolerance -10 +75 -10 +30 ------------------------------------------------- 125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275- -10 +50 Percent 135213531354135513561357135813591360136113621363136413651366136713681369137013711372137313741375- -10 +75 --------------------------------- ------------- MIL-PRF-39018/3G 6 volts 100 100 100 100 100 100 100 100 150 150 150 150 150 150 150 150 200 200 200 200 200 200 200 200 Cap. TABLE I. Styles CU16, CU17, and CUR17 capacitors - Continued. DC rated voltage +85C and 105C 1/ 2/ 3/ F 10 20 33 39 68 82 120 180 8.2 15 27 47 68 82 120 150 5.8 20 27 47 56 82 120 DC surge voltage +85C and +105C volts 275 275 275 275 275 275 275 275 325 325 325 325 325 325 325 325 375 375 375 375 375 375 375 ESR 25C 105 C 13.26 6.63 4.02 3.40 1.95 1.62 1.11 .74 24.26 13.26 7.37 4.23 2.93 2.43 1.66 1.33 35.53 9.95 7.37 4.23 3.55 2.43 1.66 Impedance (max) at -55C and 120 Hz 39.79 19.89 12.06 10.20 5.85 4.85 3.32 2.21 48.52 26.53 14.74 8.47 5.85 4.85 3.32 2.65 71.05 19.89 14.74 8.47 7.11 4.25 3.32 DC leakage 25C 250 125 80 65 40 35 25 15 320 170 93 54 37 31 21 17 450 125 93 54 45 31 21 105C A 25 35 45 50 67 80 94 111 25 35 48 63 77 87 96 112 25 42 53 66 75 86 112 150 210 270 300 402 480 564 666 150 210 288 378 462 522 576 672 150 252 318 396 450 516 672 AC ripple current (max) 120 Hz at 85C 1/ mA 96 131 212 240 299 374 548 712 69 114 166 275 355 423 547 650 57 150 208 248 332 422 581 Case size Dash number Style CUR17 3/ Style CU17 2/ low frequency vibration Capacitance Capacitance tolerance tolerance Style CU16 Capacitance tolerance -10 +30 D1 D4 E5 F2 D7 E4 F6 F7 D1 D4 D5 E6 E7 F3 F6 F7 D1 E1 F2 D7 E7 F3 F7 0476 0477 0478 0479 0480 0481 0482 0483 0484 0485 0486 0487 0488 0489 0490 0491 0492 0493 0494 0495 0496 0497 0498 -10 +50 Percent 0576 0577 0578 0579 0580 0581 0582 0583 0584 0585 0586 0587 0588 0589 0590 0591 0592 0593 0594 0595 0596 0597 0598 -10 +75 -10 +30 ----------------------------------------------- 0676 0677 0678 0679 0680 0681 0682 0683 0684 0685 0686 0687 0688 0689 0690 0691 0692 0693 0694 0695 0696 0697 0698 -10 +50 Percent 0776 0777 0778 0779 0780 0781 0782 0783 0784 0785 0786 0787 0788 0789 0790 0791 0792 0793 0794 0795 0796 0797 0798 -10 +75 -10 +30 ----------------------------------------------- 10761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098- -10 +50 Percent 11761177117811791180118111821183118411851186118711881189119011911192119311941195119611971198- Style CUR17 3/ high frequency vibration Capacitance tolerance -10 +75 -10 +30 ----------------------------------------------- 12761277127812791280128112821283128412851286128712881289129012911292129312941295 129612971298- -10 +50 Percent 13761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398- The ripple current values shown are representative values not supported by test data. Dash number will include the letter "H" to indicate high frequency vibration (when applicable) or "-" will be deleted. The last letter in the dash number will indicate the applicable FR level symbol ("M", "P", "R", or "S"). For style CUR17 parts with random vibration, the letter R shall be used in place of the dash between the specification sheet number and the dash number (i.e., M39018/03R1052M or M39018/03R1252M). -10 +75 ----------------------------------------------- MIL-PRF-39018/3G 7 volts 250 250 250 250 250 250 250 250 300 300 300 300 300 300 300 300 350 350 350 350 350 350 350 Cap. MIL-PRF-39018/3G Life: Method 108 of MIL-STD-202. For qualification: Condition F (2,000 hours) at +85C. DCL: See table I. Cap.: Within 10 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. For conformance: Performance check, condition B (250 hours) at +85C (non-ER). DCL: See table I. Cap.: Within 10 percent of initial measured value. ESR: See table I. For conformance: Continuation test (1,750 hours) at +85C (non-ER). DCL: See table I. Cap.: Within 15 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. For quality conformance: 10,000 hours (ER) at +85C. DCL: At +25C initial limit, at +85C, 125 percent of initial limit. Cap.: Within 25 percent of initial measured value. ESR: Not more than 200 percent of initial requirement. Case insulation (CU17 and CUR17 only): In accordance with MIL-PRF-39018. Vibration: Low frequency: In accordance with MIL-PRF-39018. High frequency: (When specified, see ordering data): In accordance with MIL-PRF-39018 with the following exceptions: Test condition letter A; duration and direction of motion - In accordance with method 204 of MIL-STD-202. Random (style CUR17 only): In accordance with MIL-PRF-39018. Thermal shock and immersion: Thermal shock: Method 107 of MIL-STD-202, condition A, except in step 3, units shall be tested at applicable high temperature. Immersion: Method 104 of MIL-STD-202, condition B (2 cycles, 30 minutes). DCL: See table I. Cap.: Within 5 percent of initial measured value. ESR: See table I. Case insulation (CU17 and CUR17 only): Shall meet initial requirement. Surge voltage: DCL: See table I. Cap.: Within 6 percent of initial measured value. ESR: See table I. Moisture resistance: Method 106 of MIL-STD-202. DCL: See table I. Cap: Within 6 percent of initial measured value. ESR: See table I. Case Insulation (CU17 and CUR17 only): Shall meet initial requirement. High temperature exposure (500 hours at +105C): DCL: Not more than 200 percent of initial requirement. Cap.: Within 10 percent of initial measured value. ESR: Not more than 115 percent of initial requirement. 8 MIL-PRF-39018/3G Reverse voltage: After 125 hours at 105C with 1 +0, -.1, reverse volt applied to units rated at 7 V dc and 3 +0, -.3 reverse volts applied to all others. After additional 125 hours at 105C with rated forward voltage applied: DCL: Within 125 percent of initial requirement. Cap.: Within the following percentages of the initial measured value: 7 to 30 V dc inclusive: +10, -25 percent. 50 to 350 V dc inclusive: 10 percent. ESR: See table I. Penetration of solvents: In accordance with MIL-PRF-39018. High temperature verification: In accordance with MIL-PRF-39018 at +105C with rated voltage applied: DCL: See table I. Cap: Within 10 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. Reverse voltage aging: In accordance with MIL-PRF-39018. Marking: In accordance with MIL-PRF-39018. Part or Identifying Number (PIN): M39018/03- (Dash number from table I). For CU17 and CUR17, the complete dash number will include additional letter symbol(s) as shown on table I. For style CUR17 parts with random vibration, the letter R shall be used in place of the dash (i.e., M39018/03R1052M or M39018/03R1252M). Substitutability data: See table II. Ordering data: In addition to the data specified in MIL-PRF-39018, procurement documents should specify those capacitors which are to be tested to high frequency vibration. 9 MIL-PRF-39018/3G TABLE II. Substitutability data. Dash number in MIL-PRF-39018/3A, /3B, /3C, /3D, 31E Style CU16 Style CU17 1/ Capacitance tolerance -10 +30 -10 +50 -10 +75 0401 --0501 0402 --0502 0403 --0503 0404 --0504 0405 --0505 0406 --0506 0407 --0507 0408 --0508 0409 --0509 0410 --0510 0411 --0511 0412 --0512 0413 --0513 0414 --0514 0415 --0515 0416 --0516 0417 --0517 0418 --0518 0419 --0519 0420 --0520 0421 --0521 0422 --0522 0423 --0523 0424 --0524 0425 --0525 0426 --0526 0427 --0527 0428 --0528 0429 --0529 0430 --0530 0431 --0531 0432 --0532 0433 --0533 0434 --0534 0435 --0535 0436 --0536 0437 --0537 0438 --0538 0439 --0539 0440 --0540 0441 --0541 0442 --0542 0443 --0543 0444 --0544 0445 --0545 0446 --0546 0447 --0547 0448 --0548 0449 --0549 0450 --0550 0451 --0551 Dash number MIL-PRF-39018/3 Style CU16 Style CU17 Capacitance tolerance -10 +30 -10 +50 -10 +75 0601 --0701 0602 --0702 0603 --0703 0604 --0704 0605 --0705 0606 --0706 0607 --0707 0608 --0708 0609 --0709 0610 --0710 0611 --0711 0612 --0712 0613 --0713 0614 --0714 0615 --0715 0616 --0716 0617 --0717 0618 --0718 0619 --0719 0620 --0720 0621 --0721 0622 --0722 0623 --0723 0624 --0724 0625 --0725 0626 --0726 0627 --0727 0628 --0728 0629 --0729 0630 --0730 0631 --0731 0632 --0732 0633 --0733 0634 --0734 0635 --0735 0636 --0736 0637 --0737 0638 --0738 0639 --0739 0640 --0740 0641 --0741 0642 --0742 0643 --0743 0644 --0744 0645 --0745 0646 --0746 0647 --0747 0648 --0748 0649 --0749 0650 --0750 0651 --0751 See footnotes at end of table. 10 Capacitance tolerance -10 +30 -10 +50 -10 +75 0001 --0002 0005 --0006 0009 --0010 0013 --0014 0017 --0018 0021 --0022 0025 --0026 0029 --0030 0033 --0034 0037 --0038 0041 --0042 0045 --0046 0049 --0050 0053 --0054 0057 --0058 0061 --0062 0065 --0066 0069 --0070 0073 --0074 0077 --0078 0081 --0082 0085 --0086 0089 --0090 0093 --0094 0097 --0098 0101 --0102 0105 --0106 0109 --0110 0113 --0114 0117 --0118 0121 --0122 0125 --0126 0129 --0130 0133 --0134 0137 --0138 0141 --0142 0145 --0146 0149 --0150 0153 --0154 0157 --0158 0161 --0162 0165 --0166 0169 --0170 0173 --0174 0177 --0178 0181 --0182 0185 --0186 0189 --0190 0193 --0194 0197 --0198 0201 --0202 Capacitance tolerance -10 +30 -10 +50 -10 +75 0003 --0004 0007 --0008 0011 --0012 0015 --0016 0019 --0020 0023 --0024 0027 --0028 0031 --0032 0035 --0036 0039 --0040 0043 --0044 0047 --0048 0051 --0052 0055 --0056 0059 --0060 0063 --0064 0067 --0068 0071 --0072 0075 --0076 0079 --0080 0083 --0084 0087 --0088 0091 --0092 0095 --0096 0099 --0100 0103 --0104 0107 --0108 0111 --0112 0115 --0116 0119 --0120 0123 --0124 0127 --0128 0131 --0132 0135 --0136 0139 --0140 0143 --0144 0147 --0148 0151 --0152 0155 --0156 0159 --0160 0163 --0164 0167 --0168 0171 --0172 0175 --0176 0179 --0180 0183 --0184 0187 --0188 0191 --0192 0195 --0196 0199 --0200 0203 --0204 MIL-PRF-39018/3G TABLE II. Substitutability data - Continued. Dash number in MIL-PRF-39018/3A, /3B, /3C, /3D, /3E Style CU16 Style CU17 1/ Capacitance tolerance -10 +30 -10 +50 -10 +75 0452 0552 --0453 0553 --0454 0554 --0455 0555 --0456 0556 --0457 0557 --0458 0558 --0459 0559 --0460 0560 --0461 0561 --0462 0562 --0463 0563 --0464 0564 --0465 0565 --0466 0566 --0467 0567 --0468 0568 --0469 0569 --0470 0570 --0471 0571 --0472 0572 --0473 0573 --0474 0574 --0475 0575 --- Dash number MIL-PRF-39018/3 Style CU16 Style CU17 Capacitance tolerance -10 +30 -10 +50 -10 +75 0652 0752 --0653 0753 --0654 0754 --0655 0755 --0656 0756 --0657 0757 --0658 0758 --0659 0759 --0660 0760 --0661 0761 --0662 0762 --0663 0763 --0664 0764 --0665 0765 --0666 0766 --0667 0767 --0668 0768 --0669 0769 --0670 0770 --0671 0771 --0672 0772 --0673 0773 --0674 0774 --0675 0775 --- Capacitance tolerance -10 +30 -10 +50 -10 +75 0205 0206 --0209 0210 --0213 0214 --0217 0218 --0221 0222 --0225 0226 --0229 0230 --0233 0234 --0237 0238 --0241 0242 --0245 0246 --0249 0250 --0253 0254 --0257 0258 --0261 0262 --0265 0266 --0269 0270 --0273 0274 --0277 0278 --0281 0282 --0285 0286 --0289 0290 --0293 0294 --0297 0298 --- Capacitance tolerance -10 +30 -10 +50 -10 +75 0207 0208 --0211 0212 --0215 0216 --0219 0220 --0223 0224 --0227 0228 --0231 0232 --0235 0236 --0239 0240 --0243 0244 --0247 0248 --0251 0252 --0255 0256 --0259 0260 --0263 0264 --0267 0268 --0271 0272 --0275 0276 --0279 0280 --0283 0284 --0287 0288 --0291 0292 --0295 0296 --0299 0300 1/ Style CUR17 may be substituted for style CU17. APPLICATION NOTE: Ripple current: The maximum permissible ripple current for these capacitors can be determined from table III. The appropriate multiplier from this table should be used where operation at other frequencies or temperatures is desired. Operation of these capacitors outside the limits of 60 to 100,000 Hz is not recommended. TABLE III. Ripple current multipliers. With temperature With frequency +25C 1.4 +45C 1.4 60 Hz +65C 1.2 120 Hz +85C 1.0 400 Hz ----1 k through 100 kHz 0- 60 volts 61-200 201-350 .85 .83 .80 1.0 1.0 1.0 1.1 1.15 1.3 1.15 1.2 1.4 11 MIL-PRF-39018/3G NOTES: Reference documents. MIL-PRF-39018. MIL-STD-202. Changes from previous issue. The margins of this specification are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - CR Navy - EC Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5910-2009-022) Review activities: Army - MI Navy - AS, MC, OS, SH Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil/. 12