LM61 LM61 2.7V, SOT-23 or TO-92 Temperature Sensor Literature Number: SNIS121H LM61 2.7V, SOT-23 or TO-92 Temperature Sensor General Description Applications The LM61 is a precision integrated-circuit temperature sensor that can sense a -30C to +100C temperature range while operating from a single +2.7V supply. The LM61's output voltage is linearly proportional to Celsius (Centigrade) temperature (+10 mV/C) and has a DC offset of +600 mV. The offset allows reading negative temperatures without the need for a negative supply. The nominal output voltage of the LM61 ranges from +300 mV to +1600 mV for a -30C to +100C temperature range. The LM61 is calibrated to provide accuracies of 2.0C at room temperature and 3C over the full -25C to +85C temperature range. The LM61's linear output, +600 mV offset, and factory calibration simplify external circuitry required in a single supply environment where reading negative temperatures is required. Because the LM61's quiescent current is less than 125 A, self-heating is limited to a very low 0.2C in still air. Shutdown capability for the LM61 is intrinsic because its inherent low power consumption allows it to be powered directly from the output of many logic gates. Features Calibrated linear scale factor of +10 mV/C Rated for full -30 to +100C range Suitable for remote applications UL Recognized Component Cellular Phones Computers Power Supply Modules Battery Management FAX Machines Printers HVAC Disk Drives Appliances Key Specifications Accuracy at 25C Accuracy for -30C to +100C 2.0 or 3.0C (max) 4.0C (max) Accuracy for -25C to +85C 3.0C (max) Temperature Slope Power Supply Voltage Range +10 mV/C +2.7V to +10V Current Drain @ 25C 125 A (max) Nonlinearity 0.8C (max) Output Impedance 800 (max) Typical Application 1289702 VO = (+10 mV/C x T C) + 600 mV Temperature (T) Typical VO +100C +1600 mV +85C +1450 mV +25C +850 mV 0C +600 mV -25C +350 mV -30C +300 mV FIGURE 1. Full-Range Centigrade Temperature Sensor (-30C to +100C) Operating from a Single Li-Ion Battery Cell (c) 2010 National Semiconductor Corporation 12897 www.national.com LM61 2.7V, SOT-23 or TO-92 Temperature Sensor February 9, 2010 LM61 Connection Diagrams SOT-23 TO-92 1289701 Top View See NS Package Number mf03a 1289725 See NS Package Number Z03A Ordering Information Order Number Device Top Mark Supplied In LM61BIM3 T1B 1000 Units on Tape and Reel LM61BIM3X T1B 3000 Units on Tape and Reel LM61CIM3 T1C 1000 Units on Tape and Reel LM61CIM3X T1C 3000 Units on Tape and Reel Accuracy Over Specified Temperature Range (C) Specified Temperature Range 3 -25C to +85C SOT-23 4 -30C to +100C LM61BIZ LM61BIZ Bulk 3 -25C to +85C LM61CIZ LM61CIZ Bulk 4 -30C to +100C www.national.com 2 Package Type TO-92 Supply Voltage Output Voltage Output Current Input Current at any pin (Note 2) Storage Temperature Maximum Junction Temperature (TJMAX) ESD Susceptibility (Note 3) : Human Body Model Machine Model Operating Ratings (Note 1) TMIN TA TMAX Specified Temperature Range: +12V to -0.2V (+VS + 0.6V) to -0.6V 10 mA 5 mA -65C to +150C LM61 Absolute Maximum Ratings (Note 1) -30C TA +100C LM61C -25C TA +85C LM61B Supply Voltage Range (+VS) +2.7V to +10V Thermal Resistance, JA(Note 5) SOT-23 TO-92 +125C 450C/W 180C/W Soldering process must comply with National Semiconductor's Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 4) 2500V 250V Electrical Characteristics Unless otherwise noted, these specifications apply for +VS = +3.0 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all other limits TA = TJ = 25C. Parameter Conditions Typical (Note 6) Accuracy (Note 8) Output Voltage at 0C Limits (Note 7) Units (Limit) 2.0 3.0 C (max) 3.0 4.0 C (max) mV 0.6 0.8 C (max) +9.7 +10.3 +9.6 +10.4 mV/C (min) mV/C (max) -30C TA +85C, +VS= +2.7V 0.8 2.3 5 0.8 2.3 5 k (max) k (max) k (max) +3.0V +VS +10V 0.7 0.7 mV/V (max) +2.7V +VS +3.3V 5.7 5.7 mV (max) 125 125 A (max) 155 155 A (max) Sensor Gain (Average Slope) +10 +3.0V +VS +10V +85C TA +100C, +VS= +2.7V Line Regulation (Note 10) LM61C Limits (Note 7) +600 Nonlinearity (Note 9) Output Impedance LM61B Quiescent Current +2.7V +VS +10V 82 Change of Quiescent Current +2.7V +VS +10V 5 A 0.2 A/C 0.2 C Temperature Coefficient of Quiescent Current Long Term Stability (Note 11) TJ=TMAX=+100C, for 1000 hours Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > +VS), the current at that pin should be limited to 5 mA. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 4: Reflow temperature profiles are different for lead-free and non-lead-free packages. Note 5: The junction to ambient thermal resistance (JA) is specified without a heat sink in still air. Note 6: Typicals are at TJ = TA = 25C and represent most likely parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Accuracy is defined as the error between the output voltage and +10 mV/C times the device's case temperature plus 600 mV, at specified conditions of voltage, current, and temperature (expressed in C). Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's rated temperature range. Note 10: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. 3 www.national.com LM61 Note 11: For best long-term stability, any precision circuit will give best results if the unit is aged at a warm temperature, and/or temperature cycled for at least 46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered; allow time for stress relaxation to occur. The majority of the drift will occur in the first 1000 hours at elevated temperatures. The drift after 1000 hours will not continue at the first 1000 hour rate. Typical Performance Characteristics The LM61 in the SOT-23 package mounted to a printed circuit board as shown in Figure 2 was used to generate the following thermal curves. Thermal Time Constant Thermal Resistance Junction to Air 1289704 1289703 Thermal Response in Still Air with Heat Sink Thermal Response in Stirred Oil Bath with Heat Sink 1289705 1289706 Quiescent Current vs. Temperature Thermal Response in Still Air without a Heat Sink 1289709 1289708 www.national.com 4 LM61 Accuracy vs Temperature Noise Voltage 1289710 1289711 Supply Voltage vs Supply Current Start-Up Response 1289722 1289712 1289714 FIGURE 2. Printed Circuit Board Used for Heat Sink to Generate All Curves. 1/2 Square Printed Circuit Board with 2 oz. Copper Foil or Similar. 5 www.national.com LM61 accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the LM61 or its connections. The thermal resistance junction to ambient (JA) is the parameter used to calculate the rise of a device junction temperature due to its power dissipation. For the LM61 the equation used to calculate the rise in the die temperature is as follows: TJ = TA + JA [(+VS IQ) + (+VS - VO) IL] where IQ is the quiescent current and ILis the load current on the output. Since the LM61's junction temperature is the actual temperature being measured care should be taken to minimize the load current that the LM61 is required to drive. The table shown in Figure 3 summarizes the rise in die temperature of the LM61 without any loading with a 3.3V supply, and the thermal resistance for different conditions. 1.0 Mounting The LM61 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM61 is sensing will be within about +0.2C of the surface temperature that LM61's leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature measured would be at an intermediate temperature between the surface temperature and the air temperature. To ensure good thermal conductivity the backside of the LM61 die is directly attached to the GND pin. The lands and traces to the LM61 will, of course, be part of the printed circuit board, which is the object whose temperature is being measured. Alternatively, the LM61 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM61 and SOT-23* no heat sink TJ - TA JA Still air SOT-23** small heat fin TJ - TA JA TO-92* no heat sink TJ - TA JA TO-92*** small heat fin TJ - TA JA (C/W) (C) (C/W) (C) (C/W) (C) (C/W) (C) 450 0.26 260 0.13 180 0.09 140 0.07 180 0.09 90 0.05 70 0.03 Moving air *Part soldered to 30 gauge wire. **Heat sink used is 1/2 square printed circuit board with 2 oz. foil with part attached as shown in Figure 2. ***Part glued and leads soldered to 1" square of 1/16" printed circuit board with 2oz. foil or similar. FIGURE 3. Temperature Rise of LM61 Due to Self-Heating and Thermal Resistance (JA) 2.0 Capacitive Loads The LM61 handles capacitive loading well. Without any special precautions, the LM61 can drive any capacitive load as shown in Figure 4. Over the specified temperature range the LM61 has a maximum output impedance of 5 k. In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It is recommended that 0.1 F be added from +VS to GND to bypass the power supply voltage, as shown in Figure 5. In a noisy environment it may be necessary to add a capacitor from the output to ground. A 1 F output capacitor with the 5 k maximum output impedance will form a 32 Hz lowpass filter. Since the thermal time constant of the LM61 is much slower than the 5 ms time constant formed by the RC, the overall response time of the LM61 will not be significantly affected. For much larger capacitors this additional time lag will increase the overall response time of the LM61. 1289716 FIGURE 5. LM61 with Filter for Noisy Environment 1289715 FIGURE 4. LM61 No Decoupling Required for Capacitive Load www.national.com 6 LM61 1289717 FIGURE 6. Simplified Schematic 7 www.national.com LM61 3.0 Applications Circuits 1289718 FIGURE 7. Centigrade Thermostat 1289719 FIGURE 8. Conserving Power Dissipation with Shutdown 4.0 Recommended Solder Pads for SOT-23 Package 1289720 www.national.com 8 LM61 Physical Dimensions inches (millimeters) unless otherwise noted SOT-23 Molded Small Outline Transistor Package (M3) Order Number LM61BIM3, LM61BIM3X, LM61CIM3 or LM61CIM3X NS Package Number mf03a 9 www.national.com LM61 TO-92 Plastic Package (Z) Order Number LM61BIZ or LM61CIZ NS Package Number Z03A www.national.com 10 LM61 Notes 11 www.national.com LM61 2.7V, SOT-23 or TO-92 Temperature Sensor Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated