LM61
LM61 2.7V, SOT-23 or TO-92 Temperature Sensor
Literature Number: SNIS121H
LM61
February 9, 2010
2.7V, SOT-23 or TO-92 Temperature Sensor
General Description
The LM61 is a precision integrated-circuit temperature sensor
that can sense a −30°C to +100°C temperature range while
operating from a single +2.7V supply. The LM61's output volt-
age is linearly proportional to Celsius (Centigrade) tempera-
ture (+10 mV/°C) and has a DC offset of +600 mV. The offset
allows reading negative temperatures without the need for a
negative supply. The nominal output voltage of the LM61
ranges from +300 mV to +1600 mV for a −30°C to +100°C
temperature range. The LM61 is calibrated to provide accu-
racies of ±2.0°C at room temperature and ±3°C over the full
−25°C to +85°C temperature range.
The LM61's linear output, +600 mV offset, and factory cali-
bration simplify external circuitry required in a single supply
environment where reading negative temperatures is re-
quired. Because the LM61's quiescent current is less than
125 μA, self-heating is limited to a very low 0.2°C in still air.
Shutdown capability for the LM61 is intrinsic because its in-
herent low power consumption allows it to be powered directly
from the output of many logic gates.
Features
■Calibrated linear scale factor of +10 mV/°C
■Rated for full −30° to +100°C range
■Suitable for remote applications
■UL Recognized Component
Applications
■Cellular Phones
■Computers
■Power Supply Modules
■Battery Management
■FAX Machines
■Printers
■HVAC
■Disk Drives
■Appliances
Key Specifications
■ Accuracy at 25°C ±2.0 or ±3.0°C
(max)
■ Accuracy for −30°C to +100°C ±4.0°C (max)
■ Accuracy for −25°C to +85°C ±3.0°C (max)
■ Temperature Slope +10 mV/°C
■ Power Supply Voltage Range +2.7V to +10V
■ Current Drain @ 25°C 125 µA (max)
■ Nonlinearity ±0.8°C (max)
■ Output Impedance 800 Ω (max)
Typical Application
1289702
VO = (+10 mV/°C × T °C) + 600 mV
Temperature (T) Typical VO
+100°C +1600 mV
+85°C +1450 mV
+25°C +850 mV
0°C +600 mV
−25°C +350 mV
−30°C +300 mV
FIGURE 1. Full-Range Centigrade Temperature Sensor (−30°C to +100°C)
Operating from a Single Li-Ion Battery Cell
© 2010 National Semiconductor Corporation 12897 www.national.com
LM61 2.7V, SOT-23 or TO-92 Temperature Sensor
Connection Diagrams
SOT-23
1289701
Top View
See NS Package Number mf03a
TO-92
1289725
See NS Package Number Z03A
Ordering Information
Order
Number
Device
Top Mark Supplied In
Accuracy
Over
Specified
Temperature
Range (°C)
Specified
Temperature
Range
Package
Type
LM61BIM3 T1B 1000 Units on Tape and Reel ± 3 −25°C to +85°C
SOT-23
LM61BIM3X T1B 3000 Units on Tape and Reel
LM61CIM3 T1C 1000 Units on Tape and Reel ± 4 −30°C to +100°C
LM61CIM3X T1C 3000 Units on Tape and Reel
LM61BIZ LM61BIZ Bulk ± 3 −25°C to +85°C TO-92
LM61CIZ LM61CIZ Bulk ± 4 −30°C to +100°C
www.national.com 2
LM61
Absolute Maximum Ratings (Note 1)
Supply Voltage +12V to −0.2V
Output Voltage (+VS + 0.6V) to
−0.6V
Output Current 10 mA
Input Current at any pin (Note 2) 5 mA
Storage Temperature −65°C to +150°C
Maximum Junction Temperature
(TJMAX)+125°C
ESD Susceptibility (Note 3) :
Human Body Model 2500V
Machine Model 250V
Operating Ratings (Note 1)
Specified Temperature Range: TMIN ≤ TA ≤ TMAX
LM61C −30°C ≤ TA ≤ +100°C
LM61B −25°C ≤ TA ≤ +85°C
Supply Voltage Range (+VS)+2.7V to +10V
Thermal Resistance, θJA(Note 5)
SOT-23
TO-92
450°C/W
180°C/W
Soldering process must comply with National
Semiconductor's Reflow Temperature Profile specifications.
Refer to www.national.com/packaging. (Note 4)
Electrical Characteristics
Unless otherwise noted, these specifications apply for +VS = +3.0 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all other
limits TA = TJ = 25°C.
Parameter Conditions Typical
(Note 6)
LM61B LM61C Units
(Limit)
Limits Limits
(Note 7) (Note 7)
Accuracy (Note 8) ±2.0 ±3.0 °C (max)
±3.0 ±4.0 °C (max)
Output Voltage at 0°C +600 mV
Nonlinearity (Note 9) ±0.6 ±0.8 °C (max)
Sensor Gain +10 +9.7 +9.6 mV/°C (min)
(Average Slope) +10.3 +10.4 mV/°C (max)
Output Impedance +3.0V ≤ +VS ≤ +10V
−30°C ≤ TA ≤ +85°C, +VS= +2.7V
+85°C ≤ TA ≤ +100°C, +VS= +2.7V
0.8
2.3
5
0.8
2.3
5
kΩ (max)
kΩ (max)
kΩ (max)
Line Regulation (Note 10)+3.0V ≤ +VS ≤ +10V ±0.7 ±0.7 mV/V (max)
+2.7V ≤ +VS ≤ +3.3V ±5.7 ±5.7 mV (max)
Quiescent Current +2.7V ≤ +VS ≤ +10V 82 125 125 µA (max)
155 155 µA (max)
Change of Quiescent Current +2.7V ≤ +VS ≤ +10V ±5 μA
Temperature Coefficient of 0.2 µA/°C
Quiescent Current
Long Term Stability (Note 11) TJ=TMAX=+100°C,
for 1000 hours ±0.2 °C
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > +VS), the current at that pin should be limited to 5 mA.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged
directly into each pin.
Note 4: Reflow temperature profiles are different for lead-free and non-lead-free packages.
Note 5: The junction to ambient thermal resistance (θJA) is specified without a heat sink in still air.
Note 6: Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: Accuracy is defined as the error between the output voltage and +10 mV/°C times the device's case temperature plus 600 mV, at specified conditions of
voltage, current, and temperature (expressed in °C).
Note 9: Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's rated temperature
range.
Note 10: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be
computed by multiplying the internal dissipation by the thermal resistance.
3 www.national.com
LM61
Note 11: For best long-term stability, any precision circuit will give best results if the unit is aged at a warm temperature, and/or temperature cycled for at least
46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered; allow time for stress relaxation to occur.
The majority of the drift will occur in the first 1000 hours at elevated temperatures. The drift after 1000 hours will not continue at the first 1000 hour rate.
Typical Performance Characteristics The LM61 in the SOT-23 package mounted to a printed circuit
board as shown in Figure 2 was used to generate the following thermal curves.
Thermal Resistance
Junction to Air
1289703
Thermal Time Constant
1289704
Thermal Response in
Still Air with Heat Sink
1289705
Thermal Response
in Stirred Oil Bath
with Heat Sink
1289706
Thermal Response in Still
Air without a Heat Sink
1289708
Quiescent Current
vs. Temperature
1289709
www.national.com 4
LM61
Accuracy vs Temperature
1289710
Noise Voltage
1289711
Supply Voltage
vs Supply Current
1289712
Start-Up Response
1289722
1289714
FIGURE 2. Printed Circuit Board Used
for Heat Sink to Generate All Curves.
½″ Square Printed Circuit Board
with 2 oz. Copper Foil or Similar.
5 www.national.com
LM61
1.0 Mounting
The LM61 can be applied easily in the same way as other
integrated-circuit temperature sensors. It can be glued or ce-
mented to a surface. The temperature that the LM61 is sens-
ing will be within about +0.2°C of the surface temperature that
LM61's leads are attached to.
This presumes that the ambient air temperature is almost the
same as the surface temperature; if the air temperature were
much higher or lower than the surface temperature, the actual
temperature measured would be at an intermediate temper-
ature between the surface temperature and the air tempera-
ture.
To ensure good thermal conductivity the backside of the
LM61 die is directly attached to the GND pin. The lands and
traces to the LM61 will, of course, be part of the printed circuit
board, which is the object whose temperature is being mea-
sured.
Alternatively, the LM61 can be mounted inside a sealed-end
metal tube, and can then be dipped into a bath or screwed
into a threaded hole in a tank. As with any IC, the LM61 and
accompanying wiring and circuits must be kept insulated and
dry, to avoid leakage and corrosion. This is especially true if
the circuit may operate at cold temperatures where conden-
sation can occur. Printed-circuit coatings and varnishes such
as Humiseal and epoxy paints or dips are often used to ensure
that moisture cannot corrode the LM61 or its connections.
The thermal resistance junction to ambient (θJA) is the pa-
rameter used to calculate the rise of a device junction tem-
perature due to its power dissipation. For the LM61 the
equation used to calculate the rise in the die temperature is
as follows:
TJ = TA + θJA [(+VS IQ) + (+VS − VO) IL]
where IQ is the quiescent current and ILis the load current on
the output. Since the LM61's junction temperature is the ac-
tual temperature being measured care should be taken to
minimize the load current that the LM61 is required to drive.
The table shown in Figure 3 summarizes the rise in die tem-
perature of the LM61 without any loading with a 3.3V supply,
and the thermal resistance for different conditions.
SOT-23* SOT-23** TO-92* TO-92***
no heat sink small heat fin no heat sink small heat fin
θJA TJ − TAθJA TJ − TAθJA TJ − TAθJA TJ − TA
(°C/W) (°C) (°C/W) (°C) (°C/W) (°C) (°C/W) (°C)
Still air 450 0.26 260 0.13 180 0.09 140 0.07
Moving air 180 0.09 90 0.05 70 0.03
*Part soldered to 30 gauge wire.
**Heat sink used is ½″ square printed circuit board with 2 oz. foil with part attached as shown in Figure 2.
***Part glued and leads soldered to 1" square of 1/16" printed circuit board with 2oz. foil or similar.
FIGURE 3. Temperature Rise of LM61 Due to
Self-Heating and Thermal Resistance (θJA)
2.0 Capacitive Loads
The LM61 handles capacitive loading well. Without any spe-
cial precautions, the LM61 can drive any capacitive load as
shown in Figure 4. Over the specified temperature range the
LM61 has a maximum output impedance of 5 kΩ. In an ex-
tremely noisy environment it may be necessary to add some
filtering to minimize noise pickup. It is recommended that
0.1 μF be added from +VS to GND to bypass the power supply
voltage, as shown in Figure 5. In a noisy environment it may
be necessary to add a capacitor from the output to ground. A
1 μF output capacitor with the 5 kΩ maximum output
impedance will form a 32 Hz lowpass filter. Since the thermal
time constant of the LM61 is much slower than the 5 ms time
constant formed by the RC, the overall response time of the
LM61 will not be significantly affected. For much larger ca-
pacitors this additional time lag will increase the overall re-
sponse time of the LM61.
1289715
FIGURE 4. LM61 No Decoupling Required for Capacitive
Load
1289716
FIGURE 5. LM61 with Filter for Noisy Environment
www.national.com 6
LM61
1289717
FIGURE 6. Simplified Schematic
7 www.national.com
LM61
3.0 Applications Circuits
1289718
FIGURE 7. Centigrade Thermostat
1289719
FIGURE 8. Conserving Power Dissipation with Shutdown
4.0 Recommended Solder Pads for SOT-23 Package
1289720
www.national.com 8
LM61
Physical Dimensions inches (millimeters) unless otherwise noted
SOT-23 Molded Small Outline Transistor Package (M3)
Order Number LM61BIM3, LM61BIM3X, LM61CIM3 or LM61CIM3X
NS Package Number mf03a
9 www.national.com
LM61
TO-92 Plastic Package (Z)
Order Number LM61BIZ or LM61CIZ
NS Package Number Z03A
www.national.com 10
LM61
Notes
11 www.national.com
LM61
Notes
LM61 2.7V, SOT-23 or TO-92 Temperature Sensor
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
